From: Sourav Poddar <sourav.poddar@ti.com>
To: tony@atomide.com, linux-omap@vger.kernel.org,
devicetree-discuss@lists.ozlabs.org,
linux-arm-kernel@lists.infradead.org, balbi@ti.com,
santosh.shilimkar@ti.com, b-cousson@ti.com
Cc: Sourav Poddar <sourav.poddar@ti.com>, Andrew Morton <akpm@osdl.org>
Subject: [Resend/PATCH 2/5] arm: dts: omap5-evm: Add I2c pinctrl data
Date: Mon, 11 Mar 2013 19:15:51 +0530 [thread overview]
Message-ID: <1363009551-19503-1-git-send-email-sourav.poddar@ti.com> (raw)
Booting 3.9-rc2 on omap 5430evm results in the following error
omap_i2c 48070000.i2c: did not get pins for i2c error: -19
[ 1.024261] omap_i2c 48070000.i2c: bus 0 rev0.12 at 100 kHz
[ 1.030181] omap_i2c 48072000.i2c: did not get pins for i2c error: -19
[ 1.037384] omap_i2c 48072000.i2c: bus 1 rev0.12 at 400 kHz
[ 1.043762] omap_i2c 48060000.i2c: did not get pins for i2c error: -19
[ 1.050964] omap_i2c 48060000.i2c: bus 2 rev0.12 at 100 kHz
[ 1.056823] omap_i2c 4807a000.i2c: did not get pins for i2c error: -19
[ 1.064025] omap_i2c 4807a000.i2c: bus 3 rev0.12 at 400 kHz
This happens because omap5 dts file is not adapted to use i2c through pinctrl
framework. Populating i2c pinctrl data to get rid of the error.
Tested on omap5430 evm with 3.9-rc2 kernel.
Cc: Andrew Morton <akpm@osdl.org>
Signed-off-by: Sourav Poddar <sourav.poddar@ti.com>
---
arch/arm/boot/dts/omap5-evm.dts | 62 +++++++++++++++++++++++++++++++++++++++
1 files changed, 62 insertions(+), 0 deletions(-)
diff --git a/arch/arm/boot/dts/omap5-evm.dts b/arch/arm/boot/dts/omap5-evm.dts
index 8722c15..a4784be 100644
--- a/arch/arm/boot/dts/omap5-evm.dts
+++ b/arch/arm/boot/dts/omap5-evm.dts
@@ -80,6 +80,41 @@
0x15a 0x100 /* abemcbsp2_clkx.abemcbsp2_clkx INPUT | MODE0 */
>;
};
+
+ i2c1_pins: pinmux_i2c1_pins {
+ pinctrl-single,pins = <
+ 0x1b2 0x118 /* i2c1_scl PULLUP | INPUTENABLE | MODE0 */
+ 0x1b4 0x118 /* i2c1_sda PULLUP | INPUTENABLE | MODE0 */
+ >;
+ };
+
+ i2c2_pins: pinmux_i2c2_pins {
+ pinctrl-single,pins = <
+ 0x178 0x100 /* i2c2_scl INPUTENABLE | MODE0 */
+ 0x17a 0x100 /* i2c2_sda INPUTENABLE | MODE0 */
+ >;
+ };
+
+ i2c3_pins: pinmux_i2c3_pins {
+ pinctrl-single,pins = <
+ 0x13a 0x100 /* i2c3_scl INPUTENABLE | MODE0 */
+ 0x13c 0x100 /* i2c3_sda INPUTENABLE | MODE0 */
+ >;
+ };
+
+ i2c4_pins: pinmux_i2c4_pins {
+ pinctrl-single,pins = <
+ 0xb8 0x100 /* i2c4_scl INPUTENABLE | MODE0 */
+ 0xba 0x100 /* i2c4_sda INPUTENABLE | MODE0 */
+ >;
+ };
+
+ i2c5_pins: pinmux_i2c5_pins {
+ pinctrl-single,pins = <
+ 0x184 0x100 /* i2c5_scl INPUTENABLE | MODE0 */
+ 0x186 0x100 /* i2c5_sda INPUTENABLE | MODE0 */
+ >;
+ };
};
&mmc1 {
@@ -106,7 +141,17 @@
status = "disabled";
};
+&i2c1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c1_pins>;
+
+ clock-frequency = <400000>;
+};
+
&i2c2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c2_pins>;
+
clock-frequency = <400000>;
/* Pressure Sensor */
@@ -116,7 +161,17 @@
};
};
+&i2c3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c3_pins>;
+
+ clock-frequency = <400000>;
+};
+
&i2c4 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c4_pins>;
+
clock-frequency = <400000>;
/* Temperature Sensor */
@@ -126,6 +181,13 @@
};
};
+&i2c5 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c5_pins>;
+
+ clock-frequency = <400000>;
+};
+
&keypad {
keypad,num-rows = <8>;
keypad,num-columns = <8>;
--
1.7.1
WARNING: multiple messages have this Message-ID (diff)
From: sourav.poddar@ti.com (Sourav Poddar)
To: linux-arm-kernel@lists.infradead.org
Subject: [Resend/PATCH 2/5] arm: dts: omap5-evm: Add I2c pinctrl data
Date: Mon, 11 Mar 2013 19:15:51 +0530 [thread overview]
Message-ID: <1363009551-19503-1-git-send-email-sourav.poddar@ti.com> (raw)
Booting 3.9-rc2 on omap 5430evm results in the following error
omap_i2c 48070000.i2c: did not get pins for i2c error: -19
[ 1.024261] omap_i2c 48070000.i2c: bus 0 rev0.12 at 100 kHz
[ 1.030181] omap_i2c 48072000.i2c: did not get pins for i2c error: -19
[ 1.037384] omap_i2c 48072000.i2c: bus 1 rev0.12 at 400 kHz
[ 1.043762] omap_i2c 48060000.i2c: did not get pins for i2c error: -19
[ 1.050964] omap_i2c 48060000.i2c: bus 2 rev0.12 at 100 kHz
[ 1.056823] omap_i2c 4807a000.i2c: did not get pins for i2c error: -19
[ 1.064025] omap_i2c 4807a000.i2c: bus 3 rev0.12 at 400 kHz
This happens because omap5 dts file is not adapted to use i2c through pinctrl
framework. Populating i2c pinctrl data to get rid of the error.
Tested on omap5430 evm with 3.9-rc2 kernel.
Cc: Andrew Morton <akpm@osdl.org>
Signed-off-by: Sourav Poddar <sourav.poddar@ti.com>
---
arch/arm/boot/dts/omap5-evm.dts | 62 +++++++++++++++++++++++++++++++++++++++
1 files changed, 62 insertions(+), 0 deletions(-)
diff --git a/arch/arm/boot/dts/omap5-evm.dts b/arch/arm/boot/dts/omap5-evm.dts
index 8722c15..a4784be 100644
--- a/arch/arm/boot/dts/omap5-evm.dts
+++ b/arch/arm/boot/dts/omap5-evm.dts
@@ -80,6 +80,41 @@
0x15a 0x100 /* abemcbsp2_clkx.abemcbsp2_clkx INPUT | MODE0 */
>;
};
+
+ i2c1_pins: pinmux_i2c1_pins {
+ pinctrl-single,pins = <
+ 0x1b2 0x118 /* i2c1_scl PULLUP | INPUTENABLE | MODE0 */
+ 0x1b4 0x118 /* i2c1_sda PULLUP | INPUTENABLE | MODE0 */
+ >;
+ };
+
+ i2c2_pins: pinmux_i2c2_pins {
+ pinctrl-single,pins = <
+ 0x178 0x100 /* i2c2_scl INPUTENABLE | MODE0 */
+ 0x17a 0x100 /* i2c2_sda INPUTENABLE | MODE0 */
+ >;
+ };
+
+ i2c3_pins: pinmux_i2c3_pins {
+ pinctrl-single,pins = <
+ 0x13a 0x100 /* i2c3_scl INPUTENABLE | MODE0 */
+ 0x13c 0x100 /* i2c3_sda INPUTENABLE | MODE0 */
+ >;
+ };
+
+ i2c4_pins: pinmux_i2c4_pins {
+ pinctrl-single,pins = <
+ 0xb8 0x100 /* i2c4_scl INPUTENABLE | MODE0 */
+ 0xba 0x100 /* i2c4_sda INPUTENABLE | MODE0 */
+ >;
+ };
+
+ i2c5_pins: pinmux_i2c5_pins {
+ pinctrl-single,pins = <
+ 0x184 0x100 /* i2c5_scl INPUTENABLE | MODE0 */
+ 0x186 0x100 /* i2c5_sda INPUTENABLE | MODE0 */
+ >;
+ };
};
&mmc1 {
@@ -106,7 +141,17 @@
status = "disabled";
};
+&i2c1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c1_pins>;
+
+ clock-frequency = <400000>;
+};
+
&i2c2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c2_pins>;
+
clock-frequency = <400000>;
/* Pressure Sensor */
@@ -116,7 +161,17 @@
};
};
+&i2c3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c3_pins>;
+
+ clock-frequency = <400000>;
+};
+
&i2c4 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c4_pins>;
+
clock-frequency = <400000>;
/* Temperature Sensor */
@@ -126,6 +181,13 @@
};
};
+&i2c5 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c5_pins>;
+
+ clock-frequency = <400000>;
+};
+
&keypad {
keypad,num-rows = <8>;
keypad,num-columns = <8>;
--
1.7.1
next reply other threads:[~2013-03-11 13:45 UTC|newest]
Thread overview: 2+ messages / expand[flat|nested] mbox.gz Atom feed top
2013-03-11 13:45 Sourav Poddar [this message]
2013-03-11 13:45 ` [Resend/PATCH 2/5] arm: dts: omap5-evm: Add I2c pinctrl data Sourav Poddar
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1363009551-19503-1-git-send-email-sourav.poddar@ti.com \
--to=sourav.poddar@ti.com \
--cc=akpm@osdl.org \
--cc=b-cousson@ti.com \
--cc=balbi@ti.com \
--cc=devicetree-discuss@lists.ozlabs.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-omap@vger.kernel.org \
--cc=santosh.shilimkar@ti.com \
--cc=tony@atomide.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.