From: Aaro Koskinen <aaro.koskinen-X3B1VOXEql0@public.gmane.org> To: Felipe Balbi <balbi-l0cyMroinI0@public.gmane.org>, linux-usb-u79uwXL29TY76Z2rM5mHXA@public.gmane.org, linux-omap-u79uwXL29TY76Z2rM5mHXA@public.gmane.org, linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r@public.gmane.org Cc: Aaro Koskinen <aaro.koskinen-X3B1VOXEql0@public.gmane.org> Subject: [PATCH v4 3/4] USB: OMAP1: OTG controller driver Date: Fri, 6 Dec 2013 16:13:06 +0200 [thread overview] Message-ID: <1386339187-28466-4-git-send-email-aaro.koskinen@iki.fi> (raw) In-Reply-To: <1386339187-28466-1-git-send-email-aaro.koskinen-X3B1VOXEql0@public.gmane.org> Transceivers need to manage OTG controller state on OMAP1 to enable switching between peripheral and host modes. Provide a driver for that. Signed-off-by: Aaro Koskinen <aaro.koskinen-X3B1VOXEql0@public.gmane.org> --- drivers/usb/phy/Kconfig | 10 +++ drivers/usb/phy/Makefile | 1 + drivers/usb/phy/phy-omap-otg.c | 169 +++++++++++++++++++++++++++++++++++++++++ 3 files changed, 180 insertions(+) create mode 100644 drivers/usb/phy/phy-omap-otg.c diff --git a/drivers/usb/phy/Kconfig b/drivers/usb/phy/Kconfig index d5589f9c60a9..95d0acc117cc 100644 --- a/drivers/usb/phy/Kconfig +++ b/drivers/usb/phy/Kconfig @@ -154,6 +154,16 @@ config USB_GPIO_VBUS optionally control of a D+ pullup GPIO as well as a VBUS current limit regulator. +config OMAP_OTG + tristate "OMAP USB OTG controller driver" + depends on ARCH_OMAP_OTG && EXTCON + help + Enable this to support some transceivers on OMAP1 platforms. OTG + controller is needed to switch between host and peripheral modes. + + This driver can also be built as a module. If so, the module + will be called omap-otg. + config USB_ISP1301 tristate "NXP ISP1301 USB transceiver support" depends on USB || USB_GADGET diff --git a/drivers/usb/phy/Makefile b/drivers/usb/phy/Makefile index 2135e85f46ed..ca5bcad49da2 100644 --- a/drivers/usb/phy/Makefile +++ b/drivers/usb/phy/Makefile @@ -15,6 +15,7 @@ obj-$(CONFIG_NOP_USB_XCEIV) += phy-generic.o obj-$(CONFIG_OMAP_CONTROL_USB) += phy-omap-control.o obj-$(CONFIG_AM335X_CONTROL_USB) += phy-am335x-control.o obj-$(CONFIG_AM335X_PHY_USB) += phy-am335x.o +obj-$(CONFIG_OMAP_OTG) += phy-omap-otg.o obj-$(CONFIG_OMAP_USB2) += phy-omap-usb2.o obj-$(CONFIG_OMAP_USB3) += phy-omap-usb3.o obj-$(CONFIG_SAMSUNG_USBPHY) += phy-samsung-usb.o diff --git a/drivers/usb/phy/phy-omap-otg.c b/drivers/usb/phy/phy-omap-otg.c new file mode 100644 index 000000000000..11598cdb3189 --- /dev/null +++ b/drivers/usb/phy/phy-omap-otg.c @@ -0,0 +1,169 @@ +/* + * OMAP OTG controller driver + * + * Based on code from tahvo-usb.c and isp1301_omap.c drivers. + * + * Copyright (C) 2005-2006 Nokia Corporation + * Copyright (C) 2004 Texas Instruments + * Copyright (C) 2004 David Brownell + * + * This file is subject to the terms and conditions of the GNU General + * Public License. See the file "COPYING" in the main directory of this + * archive for more details. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + */ + +#include <linux/io.h> +#include <linux/err.h> +#include <linux/extcon.h> +#include <linux/kernel.h> +#include <linux/module.h> +#include <linux/interrupt.h> +#include <linux/platform_device.h> +#include <linux/platform_data/usb-omap1.h> + +struct otg_device { + void __iomem *base; + bool id; + bool vbus; + struct extcon_specific_cable_nb vbus_dev; + struct extcon_specific_cable_nb id_dev; + struct notifier_block vbus_nb; + struct notifier_block id_nb; +}; + +#define OMAP_OTG_CTRL 0x0c +#define OMAP_OTG_ASESSVLD (1 << 20) +#define OMAP_OTG_BSESSEND (1 << 19) +#define OMAP_OTG_BSESSVLD (1 << 18) +#define OMAP_OTG_VBUSVLD (1 << 17) +#define OMAP_OTG_ID (1 << 16) +#define OMAP_OTG_XCEIV_OUTPUTS \ + (OMAP_OTG_ASESSVLD | OMAP_OTG_BSESSEND | OMAP_OTG_BSESSVLD | \ + OMAP_OTG_VBUSVLD | OMAP_OTG_ID) + +static void omap_otg_ctrl(struct otg_device *otg_dev, u32 outputs) +{ + u32 l; + + l = readl(otg_dev->base + OMAP_OTG_CTRL); + l &= ~OMAP_OTG_XCEIV_OUTPUTS; + l |= outputs; + writel(l, otg_dev->base + OMAP_OTG_CTRL); +} + +static void omap_otg_set_mode(struct otg_device *otg_dev) +{ + if (!otg_dev->id && otg_dev->vbus) + /* Set B-session valid. */ + omap_otg_ctrl(otg_dev, OMAP_OTG_ID | OMAP_OTG_BSESSVLD); + else if (otg_dev->vbus) + /* Set A-session valid. */ + omap_otg_ctrl(otg_dev, OMAP_OTG_ASESSVLD); + else if (!otg_dev->id) + /* Set B-session end to indicate no VBUS. */ + omap_otg_ctrl(otg_dev, OMAP_OTG_ID | OMAP_OTG_BSESSEND); +} + +static int omap_otg_id_notifier(struct notifier_block *nb, + unsigned long event, void *ptr) +{ + struct otg_device *otg_dev = container_of(nb, struct otg_device, id_nb); + + otg_dev->id = event; + omap_otg_set_mode(otg_dev); + + return NOTIFY_DONE; +} + +static int omap_otg_vbus_notifier(struct notifier_block *nb, + unsigned long event, void *ptr) +{ + struct otg_device *otg_dev = container_of(nb, struct otg_device, + vbus_nb); + + otg_dev->vbus = event; + omap_otg_set_mode(otg_dev); + + return NOTIFY_DONE; +} + +static int omap_otg_probe(struct platform_device *pdev) +{ + const struct omap_usb_config *config = pdev->dev.platform_data; + struct otg_device *otg_dev; + struct extcon_dev *extcon; + int ret; + u32 rev; + + if (!config || !config->extcon) + return -ENODEV; + + extcon = extcon_get_extcon_dev(config->extcon); + if (!extcon) + return -EPROBE_DEFER; + + otg_dev = devm_kzalloc(&pdev->dev, sizeof(*otg_dev), GFP_KERNEL); + if (!otg_dev) + return -ENOMEM; + + otg_dev->base = devm_ioremap_resource(&pdev->dev, &pdev->resource[0]); + if (IS_ERR(otg_dev->base)) + return PTR_ERR(otg_dev->base); + + otg_dev->id_nb.notifier_call = omap_otg_id_notifier; + otg_dev->vbus_nb.notifier_call = omap_otg_vbus_notifier; + + ret = extcon_register_interest(&otg_dev->id_dev, config->extcon, + "USB-HOST", &otg_dev->id_nb); + if (ret) + return ret; + + ret = extcon_register_interest(&otg_dev->vbus_dev, config->extcon, + "USB", &otg_dev->vbus_nb); + if (ret) { + extcon_unregister_interest(&otg_dev->id_dev); + return ret; + } + + otg_dev->id = extcon_get_cable_state(extcon, "USB-HOST"); + otg_dev->vbus = extcon_get_cable_state(extcon, "USB"); + omap_otg_set_mode(otg_dev); + + rev = readl(otg_dev->base); + + dev_info(&pdev->dev, + "OMAP USB OTG controller rev %d.%d (%s, id=%d, vbus=%d)\n", + (rev >> 4) & 0xf, rev & 0xf, config->extcon, otg_dev->id, + otg_dev->vbus); + + return 0; +} + +static int omap_otg_remove(struct platform_device *pdev) +{ + struct otg_device *otg_dev = platform_get_drvdata(pdev); + + extcon_unregister_interest(&otg_dev->id_dev); + extcon_unregister_interest(&otg_dev->vbus_dev); + + return 0; +} + +static struct platform_driver omap_otg_driver = { + .probe = omap_otg_probe, + .remove = omap_otg_remove, + .driver = { + .owner = THIS_MODULE, + .name = "omap_otg", + }, +}; +module_platform_driver(omap_otg_driver); + +MODULE_DESCRIPTION("OMAP USB OTG controller driver"); +MODULE_LICENSE("GPL"); +MODULE_AUTHOR("Aaro Koskinen <aaro.koskinen-X3B1VOXEql0@public.gmane.org>"); -- 1.8.4.4 -- To unsubscribe from this list: send the line "unsubscribe linux-usb" in the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org More majordomo info at http://vger.kernel.org/majordomo-info.html
WARNING: multiple messages have this Message-ID (diff)
From: aaro.koskinen@iki.fi (Aaro Koskinen) To: linux-arm-kernel@lists.infradead.org Subject: [PATCH v4 3/4] USB: OMAP1: OTG controller driver Date: Fri, 6 Dec 2013 16:13:06 +0200 [thread overview] Message-ID: <1386339187-28466-4-git-send-email-aaro.koskinen@iki.fi> (raw) In-Reply-To: <1386339187-28466-1-git-send-email-aaro.koskinen@iki.fi> Transceivers need to manage OTG controller state on OMAP1 to enable switching between peripheral and host modes. Provide a driver for that. Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi> --- drivers/usb/phy/Kconfig | 10 +++ drivers/usb/phy/Makefile | 1 + drivers/usb/phy/phy-omap-otg.c | 169 +++++++++++++++++++++++++++++++++++++++++ 3 files changed, 180 insertions(+) create mode 100644 drivers/usb/phy/phy-omap-otg.c diff --git a/drivers/usb/phy/Kconfig b/drivers/usb/phy/Kconfig index d5589f9c60a9..95d0acc117cc 100644 --- a/drivers/usb/phy/Kconfig +++ b/drivers/usb/phy/Kconfig @@ -154,6 +154,16 @@ config USB_GPIO_VBUS optionally control of a D+ pullup GPIO as well as a VBUS current limit regulator. +config OMAP_OTG + tristate "OMAP USB OTG controller driver" + depends on ARCH_OMAP_OTG && EXTCON + help + Enable this to support some transceivers on OMAP1 platforms. OTG + controller is needed to switch between host and peripheral modes. + + This driver can also be built as a module. If so, the module + will be called omap-otg. + config USB_ISP1301 tristate "NXP ISP1301 USB transceiver support" depends on USB || USB_GADGET diff --git a/drivers/usb/phy/Makefile b/drivers/usb/phy/Makefile index 2135e85f46ed..ca5bcad49da2 100644 --- a/drivers/usb/phy/Makefile +++ b/drivers/usb/phy/Makefile @@ -15,6 +15,7 @@ obj-$(CONFIG_NOP_USB_XCEIV) += phy-generic.o obj-$(CONFIG_OMAP_CONTROL_USB) += phy-omap-control.o obj-$(CONFIG_AM335X_CONTROL_USB) += phy-am335x-control.o obj-$(CONFIG_AM335X_PHY_USB) += phy-am335x.o +obj-$(CONFIG_OMAP_OTG) += phy-omap-otg.o obj-$(CONFIG_OMAP_USB2) += phy-omap-usb2.o obj-$(CONFIG_OMAP_USB3) += phy-omap-usb3.o obj-$(CONFIG_SAMSUNG_USBPHY) += phy-samsung-usb.o diff --git a/drivers/usb/phy/phy-omap-otg.c b/drivers/usb/phy/phy-omap-otg.c new file mode 100644 index 000000000000..11598cdb3189 --- /dev/null +++ b/drivers/usb/phy/phy-omap-otg.c @@ -0,0 +1,169 @@ +/* + * OMAP OTG controller driver + * + * Based on code from tahvo-usb.c and isp1301_omap.c drivers. + * + * Copyright (C) 2005-2006 Nokia Corporation + * Copyright (C) 2004 Texas Instruments + * Copyright (C) 2004 David Brownell + * + * This file is subject to the terms and conditions of the GNU General + * Public License. See the file "COPYING" in the main directory of this + * archive for more details. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + */ + +#include <linux/io.h> +#include <linux/err.h> +#include <linux/extcon.h> +#include <linux/kernel.h> +#include <linux/module.h> +#include <linux/interrupt.h> +#include <linux/platform_device.h> +#include <linux/platform_data/usb-omap1.h> + +struct otg_device { + void __iomem *base; + bool id; + bool vbus; + struct extcon_specific_cable_nb vbus_dev; + struct extcon_specific_cable_nb id_dev; + struct notifier_block vbus_nb; + struct notifier_block id_nb; +}; + +#define OMAP_OTG_CTRL 0x0c +#define OMAP_OTG_ASESSVLD (1 << 20) +#define OMAP_OTG_BSESSEND (1 << 19) +#define OMAP_OTG_BSESSVLD (1 << 18) +#define OMAP_OTG_VBUSVLD (1 << 17) +#define OMAP_OTG_ID (1 << 16) +#define OMAP_OTG_XCEIV_OUTPUTS \ + (OMAP_OTG_ASESSVLD | OMAP_OTG_BSESSEND | OMAP_OTG_BSESSVLD | \ + OMAP_OTG_VBUSVLD | OMAP_OTG_ID) + +static void omap_otg_ctrl(struct otg_device *otg_dev, u32 outputs) +{ + u32 l; + + l = readl(otg_dev->base + OMAP_OTG_CTRL); + l &= ~OMAP_OTG_XCEIV_OUTPUTS; + l |= outputs; + writel(l, otg_dev->base + OMAP_OTG_CTRL); +} + +static void omap_otg_set_mode(struct otg_device *otg_dev) +{ + if (!otg_dev->id && otg_dev->vbus) + /* Set B-session valid. */ + omap_otg_ctrl(otg_dev, OMAP_OTG_ID | OMAP_OTG_BSESSVLD); + else if (otg_dev->vbus) + /* Set A-session valid. */ + omap_otg_ctrl(otg_dev, OMAP_OTG_ASESSVLD); + else if (!otg_dev->id) + /* Set B-session end to indicate no VBUS. */ + omap_otg_ctrl(otg_dev, OMAP_OTG_ID | OMAP_OTG_BSESSEND); +} + +static int omap_otg_id_notifier(struct notifier_block *nb, + unsigned long event, void *ptr) +{ + struct otg_device *otg_dev = container_of(nb, struct otg_device, id_nb); + + otg_dev->id = event; + omap_otg_set_mode(otg_dev); + + return NOTIFY_DONE; +} + +static int omap_otg_vbus_notifier(struct notifier_block *nb, + unsigned long event, void *ptr) +{ + struct otg_device *otg_dev = container_of(nb, struct otg_device, + vbus_nb); + + otg_dev->vbus = event; + omap_otg_set_mode(otg_dev); + + return NOTIFY_DONE; +} + +static int omap_otg_probe(struct platform_device *pdev) +{ + const struct omap_usb_config *config = pdev->dev.platform_data; + struct otg_device *otg_dev; + struct extcon_dev *extcon; + int ret; + u32 rev; + + if (!config || !config->extcon) + return -ENODEV; + + extcon = extcon_get_extcon_dev(config->extcon); + if (!extcon) + return -EPROBE_DEFER; + + otg_dev = devm_kzalloc(&pdev->dev, sizeof(*otg_dev), GFP_KERNEL); + if (!otg_dev) + return -ENOMEM; + + otg_dev->base = devm_ioremap_resource(&pdev->dev, &pdev->resource[0]); + if (IS_ERR(otg_dev->base)) + return PTR_ERR(otg_dev->base); + + otg_dev->id_nb.notifier_call = omap_otg_id_notifier; + otg_dev->vbus_nb.notifier_call = omap_otg_vbus_notifier; + + ret = extcon_register_interest(&otg_dev->id_dev, config->extcon, + "USB-HOST", &otg_dev->id_nb); + if (ret) + return ret; + + ret = extcon_register_interest(&otg_dev->vbus_dev, config->extcon, + "USB", &otg_dev->vbus_nb); + if (ret) { + extcon_unregister_interest(&otg_dev->id_dev); + return ret; + } + + otg_dev->id = extcon_get_cable_state(extcon, "USB-HOST"); + otg_dev->vbus = extcon_get_cable_state(extcon, "USB"); + omap_otg_set_mode(otg_dev); + + rev = readl(otg_dev->base); + + dev_info(&pdev->dev, + "OMAP USB OTG controller rev %d.%d (%s, id=%d, vbus=%d)\n", + (rev >> 4) & 0xf, rev & 0xf, config->extcon, otg_dev->id, + otg_dev->vbus); + + return 0; +} + +static int omap_otg_remove(struct platform_device *pdev) +{ + struct otg_device *otg_dev = platform_get_drvdata(pdev); + + extcon_unregister_interest(&otg_dev->id_dev); + extcon_unregister_interest(&otg_dev->vbus_dev); + + return 0; +} + +static struct platform_driver omap_otg_driver = { + .probe = omap_otg_probe, + .remove = omap_otg_remove, + .driver = { + .owner = THIS_MODULE, + .name = "omap_otg", + }, +}; +module_platform_driver(omap_otg_driver); + +MODULE_DESCRIPTION("OMAP USB OTG controller driver"); +MODULE_LICENSE("GPL"); +MODULE_AUTHOR("Aaro Koskinen <aaro.koskinen@iki.fi>"); -- 1.8.4.4
next prev parent reply other threads:[~2013-12-06 14:13 UTC|newest] Thread overview: 16+ messages / expand[flat|nested] mbox.gz Atom feed top 2013-12-06 14:13 [PATCH v4 0/4] USB: OMAP1: Tahvo USB support for 770 Aaro Koskinen 2013-12-06 14:13 ` Aaro Koskinen 2013-12-06 14:13 ` [PATCH v4 2/4] USB: OMAP1: add extcon to platform data Aaro Koskinen 2013-12-06 14:13 ` Aaro Koskinen [not found] ` <1386339187-28466-1-git-send-email-aaro.koskinen-X3B1VOXEql0@public.gmane.org> 2013-12-06 14:13 ` [PATCH v4 1/4] ARM: OMAP1: USB: move omap_usb_config " Aaro Koskinen 2013-12-06 14:13 ` Aaro Koskinen 2013-12-06 14:13 ` Aaro Koskinen [this message] 2013-12-06 14:13 ` [PATCH v4 3/4] USB: OMAP1: OTG controller driver Aaro Koskinen 2013-12-06 14:13 ` [PATCH v4 4/4] USB: OMAP1: Tahvo USB transceiver driver Aaro Koskinen 2013-12-06 14:13 ` Aaro Koskinen 2013-12-06 20:46 ` Felipe Balbi 2013-12-06 20:46 ` Felipe Balbi 2013-12-07 14:16 ` Aaro Koskinen 2013-12-07 14:16 ` Aaro Koskinen 2013-12-07 17:51 ` Felipe Balbi 2013-12-07 17:51 ` Felipe Balbi
Reply instructions: You may reply publicly to this message via plain-text email using any one of the following methods: * Save the following mbox file, import it into your mail client, and reply-to-all from there: mbox Avoid top-posting and favor interleaved quoting: https://en.wikipedia.org/wiki/Posting_style#Interleaved_style * Reply using the --to, --cc, and --in-reply-to switches of git-send-email(1): git send-email \ --in-reply-to=1386339187-28466-4-git-send-email-aaro.koskinen@iki.fi \ --to=aaro.koskinen-x3b1voxeql0@public.gmane.org \ --cc=balbi-l0cyMroinI0@public.gmane.org \ --cc=linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r@public.gmane.org \ --cc=linux-omap-u79uwXL29TY76Z2rM5mHXA@public.gmane.org \ --cc=linux-usb-u79uwXL29TY76Z2rM5mHXA@public.gmane.org \ /path/to/YOUR_REPLY https://kernel.org/pub/software/scm/git/docs/git-send-email.html * If your mail client supports setting the In-Reply-To header via mailto: links, try the mailto: linkBe sure your reply has a Subject: header at the top and a blank line before the message body.
This is an external index of several public inboxes, see mirroring instructions on how to clone and mirror all data and code used by this external index.