From: Nishanth Menon <nm@ti.com>
To: "Benoît Cousson" <bcousson@baylibre.com>,
"Tony Lindgren" <tony@atomide.com>
Cc: <devicetree@vger.kernel.org>,
<linux-arm-kernel@lists.infradead.org>,
<linux-kernel@vger.kernel.org>, <linux-omap@vger.kernel.org>,
Nishanth Menon <nm@ti.com>
Subject: [PATCH 4/4] ARM: dts: DRA7: Add device nodes for ABB
Date: Wed, 29 Jan 2014 17:46:16 -0600 [thread overview]
Message-ID: <1391039177-25284-5-git-send-email-nm@ti.com> (raw)
In-Reply-To: <1391039177-25284-1-git-send-email-nm@ti.com>
Add ABB device nodes for DRA7 family of devices. Data is based on
DRA7 Technical Reference Manual revision I (Sept 2013)
Signed-off-by: Nishanth Menon <nm@ti.com>
---
Depends on https://patchwork.kernel.org/patch/3530111/
arch/arm/boot/dts/dra7.dtsi | 132 +++++++++++++++++++++++++++++++++++++++++++
1 file changed, 132 insertions(+)
diff --git a/arch/arm/boot/dts/dra7.dtsi b/arch/arm/boot/dts/dra7.dtsi
index 1fd75aa..23a2a11 100644
--- a/arch/arm/boot/dts/dra7.dtsi
+++ b/arch/arm/boot/dts/dra7.dtsi
@@ -559,6 +559,138 @@
status = "disabled";
};
+ abb_mpu: regulator-abb-mpu {
+ compatible = "ti,abb-v3";
+ regulator-name = "abb_mpu";
+ #address-cells = <0>;
+ #size-cells = <0>;
+ clocks = <&sys_clkin1>;
+ ti,settling-time = <50>;
+ ti,clock-cycles = <16>;
+
+ reg = <0x4ae07ddc 0x4>, <0x4ae07de0 0x4>,
+ <0x4ae06014 0x4>, <0x4a003b20 0x8>,
+ <0x4ae0c158 0x4>;
+ reg-names = "setup-address", "control-address",
+ "int-address", "efuse-address",
+ "ldo-address";
+ ti,tranxdone-status-mask = <0x80>;
+ /* LDOVBBMPU_FBB_MUX_CTRL */
+ ti,ldovbb-override-mask = <0x400>;
+ /* LDOVBBMPU_FBB_VSET_OUT */
+ ti,ldovbb-vset-mask = <0x1F>;
+
+ /*
+ * NOTE: only FBB mode used but actual vset will
+ * determine final biasing
+ */
+ ti,abb_info = <
+ /*uV ABB efuse rbb_m fbb_m vset_m*/
+ 1060000 0 0x0 0 0x02000000 0x01F00000
+ 1160000 0 0x4 0 0x02000000 0x01F00000
+ 1210000 0 0x8 0 0x02000000 0x01F00000
+ >;
+ };
+
+ abb_ivahd: regulator-abb-ivahd {
+ compatible = "ti,abb-v3";
+ regulator-name = "abb_ivahd";
+ #address-cells = <0>;
+ #size-cells = <0>;
+ clocks = <&sys_clkin1>;
+ ti,settling-time = <50>;
+ ti,clock-cycles = <16>;
+
+ reg = <0x4ae07e34 0x4>, <0x4ae07e24 0x4>,
+ <0x4ae06010 0x4>, <0x4a0025cc 0x8>,
+ <0x4a002470 0x4>;
+ reg-names = "setup-address", "control-address",
+ "int-address", "efuse-address",
+ "ldo-address";
+ ti,tranxdone-status-mask = <0x40000000>;
+ /* LDOVBBIVA_FBB_MUX_CTRL */
+ ti,ldovbb-override-mask = <0x400>;
+ /* LDOVBBIVA_FBB_VSET_OUT */
+ ti,ldovbb-vset-mask = <0x1F>;
+
+ /*
+ * NOTE: only FBB mode used but actual vset will
+ * determine final biasing
+ */
+ ti,abb_info = <
+ /*uV ABB efuse rbb_m fbb_m vset_m*/
+ 1055000 0 0x0 0 0x02000000 0x01F00000
+ 1150000 0 0x4 0 0x02000000 0x01F00000
+ 1250000 0 0x8 0 0x02000000 0x01F00000
+ >;
+ };
+
+ abb_dspeve: regulator-abb-dspeve {
+ compatible = "ti,abb-v3";
+ regulator-name = "abb_dspeve";
+ #address-cells = <0>;
+ #size-cells = <0>;
+ clocks = <&sys_clkin1>;
+ ti,settling-time = <50>;
+ ti,clock-cycles = <16>;
+
+ reg = <0x4ae07e30 0x4>, <0x4ae07e20 0x4>,
+ <0x4ae06010 0x4>, <0x4a0025e0 0x8>,
+ <0x4a00246c 0x4>;
+ reg-names = "setup-address", "control-address",
+ "int-address", "efuse-address",
+ "ldo-address";
+ ti,tranxdone-status-mask = <0x20000000>;
+ /* LDOVBBDSPEVE_FBB_MUX_CTRL */
+ ti,ldovbb-override-mask = <0x400>;
+ /* LDOVBBDSPEVE_FBB_VSET_OUT */
+ ti,ldovbb-vset-mask = <0x1F>;
+
+ /*
+ * NOTE: only FBB mode used but actual vset will
+ * determine final biasing
+ */
+ ti,abb_info = <
+ /*uV ABB efuse rbb_m fbb_m vset_m*/
+ 1055000 0 0x0 0 0x02000000 0x01F00000
+ 1150000 0 0x4 0 0x02000000 0x01F00000
+ 1250000 0 0x8 0 0x02000000 0x01F00000
+ >;
+ };
+
+ abb_gpu: regulator-abb-gpu {
+ compatible = "ti,abb-v3";
+ regulator-name = "abb_gpu";
+ #address-cells = <0>;
+ #size-cells = <0>;
+ clocks = <&sys_clkin1>;
+ ti,settling-time = <50>;
+ ti,clock-cycles = <16>;
+
+ reg = <0x4ae07de4 0x4>, <0x4ae07de8 0x4>,
+ <0x4ae06010 0x4>, <0x4a003b08 0x8>,
+ <0x4ae0c154 0x4>;
+ reg-names = "setup-address", "control-address",
+ "int-address", "efuse-address",
+ "ldo-address";
+ ti,tranxdone-status-mask = <0x10000000>;
+ /* LDOVBBGPU_FBB_MUX_CTRL */
+ ti,ldovbb-override-mask = <0x400>;
+ /* LDOVBBGPU_FBB_VSET_OUT */
+ ti,ldovbb-vset-mask = <0x1F>;
+
+ /*
+ * NOTE: only FBB mode used but actual vset will
+ * determine final biasing
+ */
+ ti,abb_info = <
+ /*uV ABB efuse rbb_m fbb_m vset_m*/
+ 1090000 0 0x0 0 0x02000000 0x01F00000
+ 1210000 0 0x4 0 0x02000000 0x01F00000
+ 1280000 0 0x8 0 0x02000000 0x01F00000
+ >;
+ };
+
mcspi1: spi@48098000 {
compatible = "ti,omap4-mcspi";
reg = <0x48098000 0x200>;
--
1.7.9.5
WARNING: multiple messages have this Message-ID (diff)
From: Nishanth Menon <nm@ti.com>
To: "Benoît Cousson" <bcousson@baylibre.com>,
"Tony Lindgren" <tony@atomide.com>
Cc: devicetree@vger.kernel.org, linux-arm-kernel@lists.infradead.org,
linux-kernel@vger.kernel.org, linux-omap@vger.kernel.org,
Nishanth Menon <nm@ti.com>
Subject: [PATCH 4/4] ARM: dts: DRA7: Add device nodes for ABB
Date: Wed, 29 Jan 2014 17:46:16 -0600 [thread overview]
Message-ID: <1391039177-25284-5-git-send-email-nm@ti.com> (raw)
In-Reply-To: <1391039177-25284-1-git-send-email-nm@ti.com>
Add ABB device nodes for DRA7 family of devices. Data is based on
DRA7 Technical Reference Manual revision I (Sept 2013)
Signed-off-by: Nishanth Menon <nm@ti.com>
---
Depends on https://patchwork.kernel.org/patch/3530111/
arch/arm/boot/dts/dra7.dtsi | 132 +++++++++++++++++++++++++++++++++++++++++++
1 file changed, 132 insertions(+)
diff --git a/arch/arm/boot/dts/dra7.dtsi b/arch/arm/boot/dts/dra7.dtsi
index 1fd75aa..23a2a11 100644
--- a/arch/arm/boot/dts/dra7.dtsi
+++ b/arch/arm/boot/dts/dra7.dtsi
@@ -559,6 +559,138 @@
status = "disabled";
};
+ abb_mpu: regulator-abb-mpu {
+ compatible = "ti,abb-v3";
+ regulator-name = "abb_mpu";
+ #address-cells = <0>;
+ #size-cells = <0>;
+ clocks = <&sys_clkin1>;
+ ti,settling-time = <50>;
+ ti,clock-cycles = <16>;
+
+ reg = <0x4ae07ddc 0x4>, <0x4ae07de0 0x4>,
+ <0x4ae06014 0x4>, <0x4a003b20 0x8>,
+ <0x4ae0c158 0x4>;
+ reg-names = "setup-address", "control-address",
+ "int-address", "efuse-address",
+ "ldo-address";
+ ti,tranxdone-status-mask = <0x80>;
+ /* LDOVBBMPU_FBB_MUX_CTRL */
+ ti,ldovbb-override-mask = <0x400>;
+ /* LDOVBBMPU_FBB_VSET_OUT */
+ ti,ldovbb-vset-mask = <0x1F>;
+
+ /*
+ * NOTE: only FBB mode used but actual vset will
+ * determine final biasing
+ */
+ ti,abb_info = <
+ /*uV ABB efuse rbb_m fbb_m vset_m*/
+ 1060000 0 0x0 0 0x02000000 0x01F00000
+ 1160000 0 0x4 0 0x02000000 0x01F00000
+ 1210000 0 0x8 0 0x02000000 0x01F00000
+ >;
+ };
+
+ abb_ivahd: regulator-abb-ivahd {
+ compatible = "ti,abb-v3";
+ regulator-name = "abb_ivahd";
+ #address-cells = <0>;
+ #size-cells = <0>;
+ clocks = <&sys_clkin1>;
+ ti,settling-time = <50>;
+ ti,clock-cycles = <16>;
+
+ reg = <0x4ae07e34 0x4>, <0x4ae07e24 0x4>,
+ <0x4ae06010 0x4>, <0x4a0025cc 0x8>,
+ <0x4a002470 0x4>;
+ reg-names = "setup-address", "control-address",
+ "int-address", "efuse-address",
+ "ldo-address";
+ ti,tranxdone-status-mask = <0x40000000>;
+ /* LDOVBBIVA_FBB_MUX_CTRL */
+ ti,ldovbb-override-mask = <0x400>;
+ /* LDOVBBIVA_FBB_VSET_OUT */
+ ti,ldovbb-vset-mask = <0x1F>;
+
+ /*
+ * NOTE: only FBB mode used but actual vset will
+ * determine final biasing
+ */
+ ti,abb_info = <
+ /*uV ABB efuse rbb_m fbb_m vset_m*/
+ 1055000 0 0x0 0 0x02000000 0x01F00000
+ 1150000 0 0x4 0 0x02000000 0x01F00000
+ 1250000 0 0x8 0 0x02000000 0x01F00000
+ >;
+ };
+
+ abb_dspeve: regulator-abb-dspeve {
+ compatible = "ti,abb-v3";
+ regulator-name = "abb_dspeve";
+ #address-cells = <0>;
+ #size-cells = <0>;
+ clocks = <&sys_clkin1>;
+ ti,settling-time = <50>;
+ ti,clock-cycles = <16>;
+
+ reg = <0x4ae07e30 0x4>, <0x4ae07e20 0x4>,
+ <0x4ae06010 0x4>, <0x4a0025e0 0x8>,
+ <0x4a00246c 0x4>;
+ reg-names = "setup-address", "control-address",
+ "int-address", "efuse-address",
+ "ldo-address";
+ ti,tranxdone-status-mask = <0x20000000>;
+ /* LDOVBBDSPEVE_FBB_MUX_CTRL */
+ ti,ldovbb-override-mask = <0x400>;
+ /* LDOVBBDSPEVE_FBB_VSET_OUT */
+ ti,ldovbb-vset-mask = <0x1F>;
+
+ /*
+ * NOTE: only FBB mode used but actual vset will
+ * determine final biasing
+ */
+ ti,abb_info = <
+ /*uV ABB efuse rbb_m fbb_m vset_m*/
+ 1055000 0 0x0 0 0x02000000 0x01F00000
+ 1150000 0 0x4 0 0x02000000 0x01F00000
+ 1250000 0 0x8 0 0x02000000 0x01F00000
+ >;
+ };
+
+ abb_gpu: regulator-abb-gpu {
+ compatible = "ti,abb-v3";
+ regulator-name = "abb_gpu";
+ #address-cells = <0>;
+ #size-cells = <0>;
+ clocks = <&sys_clkin1>;
+ ti,settling-time = <50>;
+ ti,clock-cycles = <16>;
+
+ reg = <0x4ae07de4 0x4>, <0x4ae07de8 0x4>,
+ <0x4ae06010 0x4>, <0x4a003b08 0x8>,
+ <0x4ae0c154 0x4>;
+ reg-names = "setup-address", "control-address",
+ "int-address", "efuse-address",
+ "ldo-address";
+ ti,tranxdone-status-mask = <0x10000000>;
+ /* LDOVBBGPU_FBB_MUX_CTRL */
+ ti,ldovbb-override-mask = <0x400>;
+ /* LDOVBBGPU_FBB_VSET_OUT */
+ ti,ldovbb-vset-mask = <0x1F>;
+
+ /*
+ * NOTE: only FBB mode used but actual vset will
+ * determine final biasing
+ */
+ ti,abb_info = <
+ /*uV ABB efuse rbb_m fbb_m vset_m*/
+ 1090000 0 0x0 0 0x02000000 0x01F00000
+ 1210000 0 0x4 0 0x02000000 0x01F00000
+ 1280000 0 0x8 0 0x02000000 0x01F00000
+ >;
+ };
+
mcspi1: spi@48098000 {
compatible = "ti,omap4-mcspi";
reg = <0x48098000 0x200>;
--
1.7.9.5
WARNING: multiple messages have this Message-ID (diff)
From: nm@ti.com (Nishanth Menon)
To: linux-arm-kernel@lists.infradead.org
Subject: [PATCH 4/4] ARM: dts: DRA7: Add device nodes for ABB
Date: Wed, 29 Jan 2014 17:46:16 -0600 [thread overview]
Message-ID: <1391039177-25284-5-git-send-email-nm@ti.com> (raw)
In-Reply-To: <1391039177-25284-1-git-send-email-nm@ti.com>
Add ABB device nodes for DRA7 family of devices. Data is based on
DRA7 Technical Reference Manual revision I (Sept 2013)
Signed-off-by: Nishanth Menon <nm@ti.com>
---
Depends on https://patchwork.kernel.org/patch/3530111/
arch/arm/boot/dts/dra7.dtsi | 132 +++++++++++++++++++++++++++++++++++++++++++
1 file changed, 132 insertions(+)
diff --git a/arch/arm/boot/dts/dra7.dtsi b/arch/arm/boot/dts/dra7.dtsi
index 1fd75aa..23a2a11 100644
--- a/arch/arm/boot/dts/dra7.dtsi
+++ b/arch/arm/boot/dts/dra7.dtsi
@@ -559,6 +559,138 @@
status = "disabled";
};
+ abb_mpu: regulator-abb-mpu {
+ compatible = "ti,abb-v3";
+ regulator-name = "abb_mpu";
+ #address-cells = <0>;
+ #size-cells = <0>;
+ clocks = <&sys_clkin1>;
+ ti,settling-time = <50>;
+ ti,clock-cycles = <16>;
+
+ reg = <0x4ae07ddc 0x4>, <0x4ae07de0 0x4>,
+ <0x4ae06014 0x4>, <0x4a003b20 0x8>,
+ <0x4ae0c158 0x4>;
+ reg-names = "setup-address", "control-address",
+ "int-address", "efuse-address",
+ "ldo-address";
+ ti,tranxdone-status-mask = <0x80>;
+ /* LDOVBBMPU_FBB_MUX_CTRL */
+ ti,ldovbb-override-mask = <0x400>;
+ /* LDOVBBMPU_FBB_VSET_OUT */
+ ti,ldovbb-vset-mask = <0x1F>;
+
+ /*
+ * NOTE: only FBB mode used but actual vset will
+ * determine final biasing
+ */
+ ti,abb_info = <
+ /*uV ABB efuse rbb_m fbb_m vset_m*/
+ 1060000 0 0x0 0 0x02000000 0x01F00000
+ 1160000 0 0x4 0 0x02000000 0x01F00000
+ 1210000 0 0x8 0 0x02000000 0x01F00000
+ >;
+ };
+
+ abb_ivahd: regulator-abb-ivahd {
+ compatible = "ti,abb-v3";
+ regulator-name = "abb_ivahd";
+ #address-cells = <0>;
+ #size-cells = <0>;
+ clocks = <&sys_clkin1>;
+ ti,settling-time = <50>;
+ ti,clock-cycles = <16>;
+
+ reg = <0x4ae07e34 0x4>, <0x4ae07e24 0x4>,
+ <0x4ae06010 0x4>, <0x4a0025cc 0x8>,
+ <0x4a002470 0x4>;
+ reg-names = "setup-address", "control-address",
+ "int-address", "efuse-address",
+ "ldo-address";
+ ti,tranxdone-status-mask = <0x40000000>;
+ /* LDOVBBIVA_FBB_MUX_CTRL */
+ ti,ldovbb-override-mask = <0x400>;
+ /* LDOVBBIVA_FBB_VSET_OUT */
+ ti,ldovbb-vset-mask = <0x1F>;
+
+ /*
+ * NOTE: only FBB mode used but actual vset will
+ * determine final biasing
+ */
+ ti,abb_info = <
+ /*uV ABB efuse rbb_m fbb_m vset_m*/
+ 1055000 0 0x0 0 0x02000000 0x01F00000
+ 1150000 0 0x4 0 0x02000000 0x01F00000
+ 1250000 0 0x8 0 0x02000000 0x01F00000
+ >;
+ };
+
+ abb_dspeve: regulator-abb-dspeve {
+ compatible = "ti,abb-v3";
+ regulator-name = "abb_dspeve";
+ #address-cells = <0>;
+ #size-cells = <0>;
+ clocks = <&sys_clkin1>;
+ ti,settling-time = <50>;
+ ti,clock-cycles = <16>;
+
+ reg = <0x4ae07e30 0x4>, <0x4ae07e20 0x4>,
+ <0x4ae06010 0x4>, <0x4a0025e0 0x8>,
+ <0x4a00246c 0x4>;
+ reg-names = "setup-address", "control-address",
+ "int-address", "efuse-address",
+ "ldo-address";
+ ti,tranxdone-status-mask = <0x20000000>;
+ /* LDOVBBDSPEVE_FBB_MUX_CTRL */
+ ti,ldovbb-override-mask = <0x400>;
+ /* LDOVBBDSPEVE_FBB_VSET_OUT */
+ ti,ldovbb-vset-mask = <0x1F>;
+
+ /*
+ * NOTE: only FBB mode used but actual vset will
+ * determine final biasing
+ */
+ ti,abb_info = <
+ /*uV ABB efuse rbb_m fbb_m vset_m*/
+ 1055000 0 0x0 0 0x02000000 0x01F00000
+ 1150000 0 0x4 0 0x02000000 0x01F00000
+ 1250000 0 0x8 0 0x02000000 0x01F00000
+ >;
+ };
+
+ abb_gpu: regulator-abb-gpu {
+ compatible = "ti,abb-v3";
+ regulator-name = "abb_gpu";
+ #address-cells = <0>;
+ #size-cells = <0>;
+ clocks = <&sys_clkin1>;
+ ti,settling-time = <50>;
+ ti,clock-cycles = <16>;
+
+ reg = <0x4ae07de4 0x4>, <0x4ae07de8 0x4>,
+ <0x4ae06010 0x4>, <0x4a003b08 0x8>,
+ <0x4ae0c154 0x4>;
+ reg-names = "setup-address", "control-address",
+ "int-address", "efuse-address",
+ "ldo-address";
+ ti,tranxdone-status-mask = <0x10000000>;
+ /* LDOVBBGPU_FBB_MUX_CTRL */
+ ti,ldovbb-override-mask = <0x400>;
+ /* LDOVBBGPU_FBB_VSET_OUT */
+ ti,ldovbb-vset-mask = <0x1F>;
+
+ /*
+ * NOTE: only FBB mode used but actual vset will
+ * determine final biasing
+ */
+ ti,abb_info = <
+ /*uV ABB efuse rbb_m fbb_m vset_m*/
+ 1090000 0 0x0 0 0x02000000 0x01F00000
+ 1210000 0 0x4 0 0x02000000 0x01F00000
+ 1280000 0 0x8 0 0x02000000 0x01F00000
+ >;
+ };
+
mcspi1: spi at 48098000 {
compatible = "ti,omap4-mcspi";
reg = <0x48098000 0x200>;
--
1.7.9.5
next prev parent reply other threads:[~2014-01-29 23:46 UTC|newest]
Thread overview: 23+ messages / expand[flat|nested] mbox.gz Atom feed top
2014-01-29 23:46 [PATCH 0/4] ARM: dts: OMAP3630+: Add ABB device nodes Nishanth Menon
2014-01-29 23:46 ` Nishanth Menon
2014-01-29 23:46 ` Nishanth Menon
2014-01-29 23:46 ` [PATCH 1/4] ARM: dts: OMAP36xx: Add device node for ABB Nishanth Menon
2014-01-29 23:46 ` Nishanth Menon
2014-01-29 23:46 ` Nishanth Menon
2014-01-29 23:46 ` [PATCH 2/4] ARM: dts: OMAP4: Add device nodes " Nishanth Menon
2014-01-29 23:46 ` Nishanth Menon
2014-01-29 23:46 ` Nishanth Menon
2014-01-29 23:46 ` [PATCH 3/4] ARM: dts: OMAP5: " Nishanth Menon
2014-01-29 23:46 ` Nishanth Menon
2014-01-29 23:46 ` Nishanth Menon
2014-02-20 16:36 ` Nishanth Menon
2014-02-20 16:36 ` Nishanth Menon
2014-02-20 16:36 ` Nishanth Menon
2014-01-29 23:46 ` Nishanth Menon [this message]
2014-01-29 23:46 ` [PATCH 4/4] ARM: dts: DRA7: " Nishanth Menon
2014-01-29 23:46 ` Nishanth Menon
2014-03-05 19:47 ` [PATCH 0/4] ARM: dts: OMAP3630+: Add ABB device nodes Tony Lindgren
2014-03-05 19:47 ` Tony Lindgren
2014-03-05 19:49 ` Tony Lindgren
2014-03-05 19:49 ` Tony Lindgren
2014-03-05 19:49 ` Tony Lindgren
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1391039177-25284-5-git-send-email-nm@ti.com \
--to=nm@ti.com \
--cc=bcousson@baylibre.com \
--cc=devicetree@vger.kernel.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-omap@vger.kernel.org \
--cc=tony@atomide.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.