From: Sylwester Nawrocki <s.nawrocki@samsung.com> To: linux-media@vger.kernel.org, devicetree@vger.kernel.org Cc: linux-samsung-soc@vger.kernel.org, linux-arm-kernel@lists.infradead.org, robh+dt@kernel.org, mark.rutland@arm.com, galak@codeaurora.org, kyungmin.park@samsung.com, kgene.kim@samsung.com, a.hajda@samsung.com, Sylwester Nawrocki <s.nawrocki@samsung.com> Subject: [PATCH v6 01/10] Documentation: dt: Add binding documentation for S5K6A3 image sensor Date: Thu, 06 Mar 2014 17:20:10 +0100 [thread overview] Message-ID: <1394122819-9582-2-git-send-email-s.nawrocki@samsung.com> (raw) In-Reply-To: <1394122819-9582-1-git-send-email-s.nawrocki@samsung.com> This patch adds binding documentation for the Samsung S5K6A3(YX) raw image sensor. Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com> Acked-by: Kyungmin Park <kyungmin.park@samsung.com> Acked-by: Mark Rutland <mark.rutland@arm.com> --- Changes since v5: - none. Changes since v2: - rephrased 'clocks' and 'clock-names' properties' description; --- .../devicetree/bindings/media/samsung-s5k6a3.txt | 33 ++++++++++++++++++++ 1 file changed, 33 insertions(+) create mode 100644 Documentation/devicetree/bindings/media/samsung-s5k6a3.txt diff --git a/Documentation/devicetree/bindings/media/samsung-s5k6a3.txt b/Documentation/devicetree/bindings/media/samsung-s5k6a3.txt new file mode 100644 index 0000000..cce01e8 --- /dev/null +++ b/Documentation/devicetree/bindings/media/samsung-s5k6a3.txt @@ -0,0 +1,33 @@ +Samsung S5K6A3(YX) raw image sensor +--------------------------------- + +S5K6A3(YX) is a raw image sensor with MIPI CSI-2 and CCP2 image data interfaces +and CCI (I2C compatible) control bus. + +Required properties: + +- compatible : "samsung,s5k6a3"; +- reg : I2C slave address of the sensor; +- svdda-supply : core voltage supply; +- svddio-supply : I/O voltage supply; +- afvdd-supply : AF (actuator) voltage supply; +- gpios : specifier of a GPIO connected to the RESET pin; +- clocks : should contain list of phandle and clock specifier pairs + according to common clock bindings for the clocks described + in the clock-names property; +- clock-names : should contain "extclk" entry for the sensor's EXTCLK clock; + +Optional properties: + +- clock-frequency : the frequency at which the "extclk" clock should be + configured to operate, in Hz; if this property is not + specified default 24 MHz value will be used. + +The common video interfaces bindings (see video-interfaces.txt) should be +used to specify link to the image data receiver. The S5K6A3(YX) device +node should contain one 'port' child node with an 'endpoint' subnode. + +Following properties are valid for the endpoint node: + +- data-lanes : (optional) specifies MIPI CSI-2 data lanes as covered in + video-interfaces.txt. The sensor supports only one data lane. -- 1.7.9.5
WARNING: multiple messages have this Message-ID (diff)
From: s.nawrocki@samsung.com (Sylwester Nawrocki) To: linux-arm-kernel@lists.infradead.org Subject: [PATCH v6 01/10] Documentation: dt: Add binding documentation for S5K6A3 image sensor Date: Thu, 06 Mar 2014 17:20:10 +0100 [thread overview] Message-ID: <1394122819-9582-2-git-send-email-s.nawrocki@samsung.com> (raw) In-Reply-To: <1394122819-9582-1-git-send-email-s.nawrocki@samsung.com> This patch adds binding documentation for the Samsung S5K6A3(YX) raw image sensor. Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com> Acked-by: Kyungmin Park <kyungmin.park@samsung.com> Acked-by: Mark Rutland <mark.rutland@arm.com> --- Changes since v5: - none. Changes since v2: - rephrased 'clocks' and 'clock-names' properties' description; --- .../devicetree/bindings/media/samsung-s5k6a3.txt | 33 ++++++++++++++++++++ 1 file changed, 33 insertions(+) create mode 100644 Documentation/devicetree/bindings/media/samsung-s5k6a3.txt diff --git a/Documentation/devicetree/bindings/media/samsung-s5k6a3.txt b/Documentation/devicetree/bindings/media/samsung-s5k6a3.txt new file mode 100644 index 0000000..cce01e8 --- /dev/null +++ b/Documentation/devicetree/bindings/media/samsung-s5k6a3.txt @@ -0,0 +1,33 @@ +Samsung S5K6A3(YX) raw image sensor +--------------------------------- + +S5K6A3(YX) is a raw image sensor with MIPI CSI-2 and CCP2 image data interfaces +and CCI (I2C compatible) control bus. + +Required properties: + +- compatible : "samsung,s5k6a3"; +- reg : I2C slave address of the sensor; +- svdda-supply : core voltage supply; +- svddio-supply : I/O voltage supply; +- afvdd-supply : AF (actuator) voltage supply; +- gpios : specifier of a GPIO connected to the RESET pin; +- clocks : should contain list of phandle and clock specifier pairs + according to common clock bindings for the clocks described + in the clock-names property; +- clock-names : should contain "extclk" entry for the sensor's EXTCLK clock; + +Optional properties: + +- clock-frequency : the frequency at which the "extclk" clock should be + configured to operate, in Hz; if this property is not + specified default 24 MHz value will be used. + +The common video interfaces bindings (see video-interfaces.txt) should be +used to specify link to the image data receiver. The S5K6A3(YX) device +node should contain one 'port' child node with an 'endpoint' subnode. + +Following properties are valid for the endpoint node: + +- data-lanes : (optional) specifies MIPI CSI-2 data lanes as covered in + video-interfaces.txt. The sensor supports only one data lane. -- 1.7.9.5
next prev parent reply other threads:[~2014-03-06 16:20 UTC|newest] Thread overview: 47+ messages / expand[flat|nested] mbox.gz Atom feed top 2014-03-06 16:20 [PATCH v6 00/10] Add device tree support for Exynos4 camera interface Sylwester Nawrocki 2014-03-06 16:20 ` Sylwester Nawrocki 2014-03-06 16:20 ` Sylwester Nawrocki [this message] 2014-03-06 16:20 ` [PATCH v6 01/10] Documentation: dt: Add binding documentation for S5K6A3 image sensor Sylwester Nawrocki 2014-03-06 18:08 ` Philipp Zabel 2014-03-06 18:08 ` Philipp Zabel 2014-03-06 20:15 ` Sylwester Nawrocki 2014-03-06 20:15 ` Sylwester Nawrocki 2014-03-06 16:20 ` [PATCH v6 02/10] Documentation: dt: Add binding documentation for S5C73M3 camera Sylwester Nawrocki 2014-03-06 16:20 ` Sylwester Nawrocki 2014-03-06 16:20 ` [PATCH v6 03/10] Documentation: devicetree: Update Samsung FIMC DT binding Sylwester Nawrocki 2014-03-06 16:20 ` Sylwester Nawrocki 2014-03-11 12:30 ` Laurent Pinchart 2014-03-11 12:30 ` Laurent Pinchart 2014-03-11 13:38 ` Sylwester Nawrocki 2014-03-11 13:38 ` Sylwester Nawrocki 2014-03-11 14:58 ` Laurent Pinchart 2014-03-11 14:58 ` Laurent Pinchart 2014-03-11 16:00 ` [PATCH v7 3/10] " Sylwester Nawrocki 2014-03-11 16:20 ` Laurent Pinchart 2014-03-11 16:30 ` Sylwester Nawrocki 2014-03-11 16:34 ` [PATCH v8 " Sylwester Nawrocki 2014-03-11 16:38 ` Laurent Pinchart 2014-03-12 15:41 ` Mauro Carvalho Chehab 2014-03-18 10:02 ` Mark Rutland 2014-03-18 11:31 ` Sylwester Nawrocki 2014-03-06 16:20 ` [PATCH v6 04/10] V4L: Add driver for s5k6a3 image sensor Sylwester Nawrocki 2014-03-06 16:20 ` Sylwester Nawrocki 2014-03-06 16:20 ` [PATCH v6 05/10] V4L: s5c73m3: Add device tree support Sylwester Nawrocki 2014-03-06 16:20 ` Sylwester Nawrocki 2014-03-18 10:05 ` Arnd Bergmann 2014-03-18 10:05 ` Arnd Bergmann 2014-03-18 10:05 ` Arnd Bergmann 2014-03-18 11:07 ` Sylwester Nawrocki 2014-03-18 11:07 ` Sylwester Nawrocki 2014-03-06 16:20 ` [PATCH v6 06/10] exynos4-is: Use external s5k6a3 sensor driver Sylwester Nawrocki 2014-03-06 16:20 ` Sylwester Nawrocki 2014-03-06 16:20 ` [PATCH v6 07/10] exynos4-is: Add clock provider for the SCLK_CAM clock outputs Sylwester Nawrocki 2014-03-06 16:20 ` Sylwester Nawrocki 2014-03-06 16:20 ` [PATCH v6 08/10] exynos4-is: Add support for asynchronous subdevices registration Sylwester Nawrocki 2014-03-06 16:20 ` Sylwester Nawrocki 2014-03-06 16:20 ` [PATCH v6 09/10] ARM: dts: Add rear camera nodes for Exynos4412 TRATS2 board Sylwester Nawrocki 2014-03-06 16:20 ` Sylwester Nawrocki 2014-03-07 10:07 ` Sylwester Nawrocki 2014-03-07 10:07 ` Sylwester Nawrocki 2014-03-06 16:20 ` [PATCH v6 10/10] ARM: dts: exynos4: Update camera clk provider and s5k6a3 sensor node Sylwester Nawrocki 2014-03-06 16:20 ` Sylwester Nawrocki
Reply instructions: You may reply publicly to this message via plain-text email using any one of the following methods: * Save the following mbox file, import it into your mail client, and reply-to-all from there: mbox Avoid top-posting and favor interleaved quoting: https://en.wikipedia.org/wiki/Posting_style#Interleaved_style * Reply using the --to, --cc, and --in-reply-to switches of git-send-email(1): git send-email \ --in-reply-to=1394122819-9582-2-git-send-email-s.nawrocki@samsung.com \ --to=s.nawrocki@samsung.com \ --cc=a.hajda@samsung.com \ --cc=devicetree@vger.kernel.org \ --cc=galak@codeaurora.org \ --cc=kgene.kim@samsung.com \ --cc=kyungmin.park@samsung.com \ --cc=linux-arm-kernel@lists.infradead.org \ --cc=linux-media@vger.kernel.org \ --cc=linux-samsung-soc@vger.kernel.org \ --cc=mark.rutland@arm.com \ --cc=robh+dt@kernel.org \ /path/to/YOUR_REPLY https://kernel.org/pub/software/scm/git/docs/git-send-email.html * If your mail client supports setting the In-Reply-To header via mailto: links, try the mailto: linkBe sure your reply has a Subject: header at the top and a blank line before the message body.
This is an external index of several public inboxes, see mirroring instructions on how to clone and mirror all data and code used by this external index.