[PATCH v4 11/13] mmc: mmci: add f_max to variant structure

[srinivas.kandagatla@linaro.org]

From: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>

Some of the controller have maximum supported frequency, This patch adds
support in variant data structure to specify such restrictions. This
gives more flexibility in calculating the f_max before passing it to
mmc-core.

Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
---
 drivers/mmc/host/mmci.c | 14 ++++++++++++--
 1 file changed, 12 insertions(+), 2 deletions(-)

diff --git a/drivers/mmc/host/mmci.c b/drivers/mmc/host/mmci.c
index fd40f9a..202f2d5 100644
--- a/drivers/mmc/host/mmci.c
+++ b/drivers/mmc/host/mmci.c
@@ -67,6 +67,7 @@ static unsigned int fmax = 515633;
  * @blksz_datactrl4: true if Block size is at b4..b16 position in datactrl
  *		     register
  * @pwrreg_powerup: power up value for MMCIPOWER register
+ * @f_max: maximum clk frequency supported by the controller.
  * @signal_direction: input/out direction of bus signals can be indicated
  * @pwrreg_clkgate: MMCIPOWER register must be used to gate the clock
  * @busy_detect: true if busy detection on dat0 is supported
@@ -87,6 +88,7 @@ struct variant_data {
 	bool			blksz_datactrl16;
 	bool			blksz_datactrl4;
 	u32			pwrreg_powerup;
+	u32			f_max;
 	bool			signal_direction;
 	bool			pwrreg_clkgate;
 	bool			busy_detect;
@@ -98,6 +100,7 @@ static struct variant_data variant_arm = {
 	.fifohalfsize		= 8 * 4,
 	.datalength_bits	= 16,
 	.pwrreg_powerup		= MCI_PWR_UP,
+	.f_max			= 100000000,
 };
 
 static struct variant_data variant_arm_extended_fifo = {
@@ -105,6 +108,7 @@ static struct variant_data variant_arm_extended_fifo = {
 	.fifohalfsize		= 64 * 4,
 	.datalength_bits	= 16,
 	.pwrreg_powerup		= MCI_PWR_UP,
+	.f_max			= 100000000,
 };
 
 static struct variant_data variant_arm_extended_fifo_hwfc = {
@@ -113,6 +117,7 @@ static struct variant_data variant_arm_extended_fifo_hwfc = {
 	.clkreg_enable		= MCI_ARM_HWFCEN,
 	.datalength_bits	= 16,
 	.pwrreg_powerup		= MCI_PWR_UP,
+	.f_max			= 100000000,
 };
 
 static struct variant_data variant_u300 = {
@@ -123,6 +128,7 @@ static struct variant_data variant_u300 = {
 	.datalength_bits	= 16,
 	.sdio			= true,
 	.pwrreg_powerup		= MCI_PWR_ON,
+	.f_max			= 100000000,
 	.signal_direction	= true,
 	.pwrreg_clkgate		= true,
 	.pwrreg_nopower		= true,
@@ -136,6 +142,7 @@ static struct variant_data variant_nomadik = {
 	.sdio			= true,
 	.st_clkdiv		= true,
 	.pwrreg_powerup		= MCI_PWR_ON,
+	.f_max			= 100000000,
 	.signal_direction	= true,
 	.pwrreg_clkgate		= true,
 	.pwrreg_nopower		= true,
@@ -152,6 +159,7 @@ static struct variant_data variant_ux500 = {
 	.sdio			= true,
 	.st_clkdiv		= true,
 	.pwrreg_powerup		= MCI_PWR_ON,
+	.f_max			= 100000000,
 	.signal_direction	= true,
 	.pwrreg_clkgate		= true,
 	.busy_detect		= true,
@@ -171,6 +179,7 @@ static struct variant_data variant_ux500v2 = {
 	.st_clkdiv		= true,
 	.blksz_datactrl16	= true,
 	.pwrreg_powerup		= MCI_PWR_ON,
+	.f_max			= 100000000,
 	.signal_direction	= true,
 	.pwrreg_clkgate		= true,
 	.busy_detect		= true,
@@ -189,6 +198,7 @@ static struct variant_data variant_qcom = {
 	.blksz_datactrl4	= true,
 	.datalength_bits	= 24,
 	.pwrreg_powerup		= MCI_PWR_UP,
+	.f_max			= 208000000,
 };
 
 static int mmci_card_busy(struct mmc_host *mmc)
@@ -1485,8 +1495,8 @@ static int mmci_probe(struct amba_device *dev,
 	 * so we try to adjust the clock down to this,
 	 * (if possible).
 	 */
-	if (host->mclk > 100000000) {
-		ret = clk_set_rate(host->clk, 100000000);
+	if (host->mclk > host->variant->f_max) {
+		ret = clk_set_rate(host->clk, host->variant->f_max);
 		if (ret < 0)
 			goto clk_disable;
 		host->mclk = clk_get_rate(host->clk);
-- 
1.9.1