From: Krzysztof Kozlowski <k.kozlowski.k@gmail.com> To: Kukjin Kim <kgene@kernel.org>, devicetree@vger.kernel.org, linux-arm-kernel@lists.infradead.org, linux-samsung-soc@vger.kernel.org, linux-kernel@vger.kernel.org Cc: Arnd Bergmann <arnd@arndb.de>, Olof Johansson <olof@lixom.net>, Marek Szyprowski <m.szyprowski@samsung.com>, Krzysztof Kozlowski <k.kozlowski.k@gmail.com> Subject: [PATCH 7/7] ARM: dts: Use phandle notation for overriding nodes in Exynos5440 boards Date: Sun, 12 Apr 2015 21:24:54 +0900 [thread overview] Message-ID: <1428841494-20769-8-git-send-email-k.kozlowski.k@gmail.com> (raw) In-Reply-To: <1428841494-20769-1-git-send-email-k.kozlowski.k@gmail.com> The phandle notation reduces possible mistakes when overriding nodes. Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com> --- arch/arm/boot/dts/exynos5440-sd5v1.dts | 10 ++-- arch/arm/boot/dts/exynos5440-ssdk5440.dts | 85 +++++++++++++++---------------- 2 files changed, 47 insertions(+), 48 deletions(-) diff --git a/arch/arm/boot/dts/exynos5440-sd5v1.dts b/arch/arm/boot/dts/exynos5440-sd5v1.dts index 268609a42b2c..a98501bab6fc 100644 --- a/arch/arm/boot/dts/exynos5440-sd5v1.dts +++ b/arch/arm/boot/dts/exynos5440-sd5v1.dts @@ -27,13 +27,13 @@ }; }; - gmac: ethernet@00230000 { - fixed_phy; - phy_addr = <1>; - }; - spi { status = "disabled"; }; }; + +&gmac { + fixed_phy; + phy_addr = <1>; +}; diff --git a/arch/arm/boot/dts/exynos5440-ssdk5440.dts b/arch/arm/boot/dts/exynos5440-ssdk5440.dts index ff55dac6e219..e4443f4e6572 100644 --- a/arch/arm/boot/dts/exynos5440-ssdk5440.dts +++ b/arch/arm/boot/dts/exynos5440-ssdk5440.dts @@ -20,59 +20,58 @@ bootargs = "root=/dev/sda2 rw rootwait ignore_loglevel earlyprintk no_console_suspend mem=2048M@0x80000000 mem=6144M@0x100000000 console=ttySAC0,115200"; }; - spi_0: spi@D0000 { - - flash: w25q128@0 { - #address-cells = <1>; - #size-cells = <1>; - compatible = "winbond,w25q128"; - spi-max-frequency = <15625000>; - reg = <0>; - controller-data { - samsung,spi-feedback-delay = <0>; - }; + fixed-rate-clocks { + xtal { + compatible = "samsung,clock-xtal"; + clock-frequency = <50000000>; + }; + }; +}; - partition@00000 { - label = "BootLoader"; - reg = <0x60000 0x80000>; - read-only; - }; +&pcie_0 { + reset-gpio = <&pin_ctrl 5 0>; + status = "okay"; +}; - partition@e0000 { - label = "Recovery-Kernel"; - reg = <0xe0000 0x300000>; - read-only; - }; +&pcie_1 { + reset-gpio = <&pin_ctrl 22 0>; + status = "okay"; +}; - partition@3e0000 { - label = "CRAM-FS"; - reg = <0x3e0000 0x700000>; - read-only; - }; +&spi_0 { + flash: w25q128@0 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "winbond,w25q128"; + spi-max-frequency = <15625000>; + reg = <0>; + controller-data { + samsung,spi-feedback-delay = <0>; + }; - partition@ae0000 { - label = "User-Data"; - reg = <0xae0000 0x520000>; - }; + partition@00000 { + label = "BootLoader"; + reg = <0x60000 0x80000>; + read-only; + }; + partition@e0000 { + label = "Recovery-Kernel"; + reg = <0xe0000 0x300000>; + read-only; }; - }; + partition@3e0000 { + label = "CRAM-FS"; + reg = <0x3e0000 0x700000>; + read-only; + }; - fixed-rate-clocks { - xtal { - compatible = "samsung,clock-xtal"; - clock-frequency = <50000000>; + partition@ae0000 { + label = "User-Data"; + reg = <0xae0000 0x520000>; }; - }; - pcie@290000 { - reset-gpio = <&pin_ctrl 5 0>; - status = "okay"; }; - pcie@2a0000 { - reset-gpio = <&pin_ctrl 22 0>; - status = "okay"; - }; }; -- 2.1.0
WARNING: multiple messages have this Message-ID (diff)
From: k.kozlowski.k@gmail.com (Krzysztof Kozlowski) To: linux-arm-kernel@lists.infradead.org Subject: [PATCH 7/7] ARM: dts: Use phandle notation for overriding nodes in Exynos5440 boards Date: Sun, 12 Apr 2015 21:24:54 +0900 [thread overview] Message-ID: <1428841494-20769-8-git-send-email-k.kozlowski.k@gmail.com> (raw) In-Reply-To: <1428841494-20769-1-git-send-email-k.kozlowski.k@gmail.com> The phandle notation reduces possible mistakes when overriding nodes. Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com> --- arch/arm/boot/dts/exynos5440-sd5v1.dts | 10 ++-- arch/arm/boot/dts/exynos5440-ssdk5440.dts | 85 +++++++++++++++---------------- 2 files changed, 47 insertions(+), 48 deletions(-) diff --git a/arch/arm/boot/dts/exynos5440-sd5v1.dts b/arch/arm/boot/dts/exynos5440-sd5v1.dts index 268609a42b2c..a98501bab6fc 100644 --- a/arch/arm/boot/dts/exynos5440-sd5v1.dts +++ b/arch/arm/boot/dts/exynos5440-sd5v1.dts @@ -27,13 +27,13 @@ }; }; - gmac: ethernet at 00230000 { - fixed_phy; - phy_addr = <1>; - }; - spi { status = "disabled"; }; }; + +&gmac { + fixed_phy; + phy_addr = <1>; +}; diff --git a/arch/arm/boot/dts/exynos5440-ssdk5440.dts b/arch/arm/boot/dts/exynos5440-ssdk5440.dts index ff55dac6e219..e4443f4e6572 100644 --- a/arch/arm/boot/dts/exynos5440-ssdk5440.dts +++ b/arch/arm/boot/dts/exynos5440-ssdk5440.dts @@ -20,59 +20,58 @@ bootargs = "root=/dev/sda2 rw rootwait ignore_loglevel earlyprintk no_console_suspend mem=2048M at 0x80000000 mem=6144M at 0x100000000 console=ttySAC0,115200"; }; - spi_0: spi at D0000 { - - flash: w25q128 at 0 { - #address-cells = <1>; - #size-cells = <1>; - compatible = "winbond,w25q128"; - spi-max-frequency = <15625000>; - reg = <0>; - controller-data { - samsung,spi-feedback-delay = <0>; - }; + fixed-rate-clocks { + xtal { + compatible = "samsung,clock-xtal"; + clock-frequency = <50000000>; + }; + }; +}; - partition at 00000 { - label = "BootLoader"; - reg = <0x60000 0x80000>; - read-only; - }; +&pcie_0 { + reset-gpio = <&pin_ctrl 5 0>; + status = "okay"; +}; - partition at e0000 { - label = "Recovery-Kernel"; - reg = <0xe0000 0x300000>; - read-only; - }; +&pcie_1 { + reset-gpio = <&pin_ctrl 22 0>; + status = "okay"; +}; - partition at 3e0000 { - label = "CRAM-FS"; - reg = <0x3e0000 0x700000>; - read-only; - }; +&spi_0 { + flash: w25q128 at 0 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "winbond,w25q128"; + spi-max-frequency = <15625000>; + reg = <0>; + controller-data { + samsung,spi-feedback-delay = <0>; + }; - partition at ae0000 { - label = "User-Data"; - reg = <0xae0000 0x520000>; - }; + partition at 00000 { + label = "BootLoader"; + reg = <0x60000 0x80000>; + read-only; + }; + partition at e0000 { + label = "Recovery-Kernel"; + reg = <0xe0000 0x300000>; + read-only; }; - }; + partition at 3e0000 { + label = "CRAM-FS"; + reg = <0x3e0000 0x700000>; + read-only; + }; - fixed-rate-clocks { - xtal { - compatible = "samsung,clock-xtal"; - clock-frequency = <50000000>; + partition at ae0000 { + label = "User-Data"; + reg = <0xae0000 0x520000>; }; - }; - pcie at 290000 { - reset-gpio = <&pin_ctrl 5 0>; - status = "okay"; }; - pcie at 2a0000 { - reset-gpio = <&pin_ctrl 22 0>; - status = "okay"; - }; }; -- 2.1.0
next prev parent reply other threads:[~2015-04-12 12:25 UTC|newest] Thread overview: 20+ messages / expand[flat|nested] mbox.gz Atom feed top 2015-04-12 12:24 [PATCH 0/7] ARM: dts: Refactor Exynos5 boards for phandle notation Krzysztof Kozlowski 2015-04-12 12:24 ` Krzysztof Kozlowski 2015-04-12 12:24 ` [PATCH 1/7] ARM: dts: Add labels to nodes used in Exynos5 based DTS Krzysztof Kozlowski 2015-04-12 12:24 ` Krzysztof Kozlowski 2015-04-12 12:24 ` [PATCH 2/7] ARM: dts: Use phandle notation for overriding nodes in Exynos5250 Krzysztof Kozlowski 2015-04-12 12:24 ` Krzysztof Kozlowski 2015-04-12 12:24 ` [PATCH 3/7] ARM: dts: Remove duplicated I2C 7 nodes in Snow Krzysztof Kozlowski 2015-04-12 12:24 ` Krzysztof Kozlowski 2015-04-12 12:24 ` [PATCH 4/7] ARM: dts: Use phandle notation for overriding nodes in Arndale Octa Krzysztof Kozlowski 2015-04-12 12:24 ` Krzysztof Kozlowski 2015-04-12 12:24 ` [PATCH 5/7] ARM: dts: Use phandle notation for overriding nodes in Exynos5420 Krzysztof Kozlowski 2015-04-12 12:24 ` Krzysztof Kozlowski 2015-04-12 12:24 ` [PATCH 6/7] ARM: dts: Use phandle notation for overriding nodes in SMDK5420 Krzysztof Kozlowski 2015-04-12 12:24 ` Krzysztof Kozlowski 2015-04-12 12:24 ` Krzysztof Kozlowski [this message] 2015-04-12 12:24 ` [PATCH 7/7] ARM: dts: Use phandle notation for overriding nodes in Exynos5440 boards Krzysztof Kozlowski 2015-04-12 20:07 ` [PATCH 0/7] ARM: dts: Refactor Exynos5 boards for phandle notation Arnd Bergmann 2015-04-12 20:07 ` Arnd Bergmann 2015-04-13 10:54 ` Krzysztof Kozłowski 2015-04-13 10:54 ` Krzysztof Kozłowski
Reply instructions: You may reply publicly to this message via plain-text email using any one of the following methods: * Save the following mbox file, import it into your mail client, and reply-to-all from there: mbox Avoid top-posting and favor interleaved quoting: https://en.wikipedia.org/wiki/Posting_style#Interleaved_style * Reply using the --to, --cc, and --in-reply-to switches of git-send-email(1): git send-email \ --in-reply-to=1428841494-20769-8-git-send-email-k.kozlowski.k@gmail.com \ --to=k.kozlowski.k@gmail.com \ --cc=arnd@arndb.de \ --cc=devicetree@vger.kernel.org \ --cc=kgene@kernel.org \ --cc=linux-arm-kernel@lists.infradead.org \ --cc=linux-kernel@vger.kernel.org \ --cc=linux-samsung-soc@vger.kernel.org \ --cc=m.szyprowski@samsung.com \ --cc=olof@lixom.net \ /path/to/YOUR_REPLY https://kernel.org/pub/software/scm/git/docs/git-send-email.html * If your mail client supports setting the In-Reply-To header via mailto: links, try the mailto: linkBe sure your reply has a Subject: header at the top and a blank line before the message body.
This is an external index of several public inboxes, see mirroring instructions on how to clone and mirror all data and code used by this external index.