All of lore.kernel.org
 help / color / mirror / Atom feed
From: Masahiro Yamada <yamada.masahiro@socionext.com>
To: linux-i2c@vger.kernel.org
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>,
	Mika Westerberg <mika.westerberg@linux.intel.com>,
	Anders Berg <anders.berg@avagotech.com>,
	Max Schwarz <max.schwarz@online.de>,
	David Box <david.e.box@linux.intel.com>,
	Wei Yan <sledge.yanwei@huawei.com>,
	Zubair Lutfullah Kakakhel <Zubair.Kakakhel@imgtec.com>,
	Andrew Bresticker <abrestic@chromium.org>,
	Wolfram Sang <wsa@the-dreams.de>,
	linux-kernel@vger.kernel.org, Kamal Dasu <kdasu.kdev@gmail.com>,
	Laurentiu Palcu <laurentiu.palcu@intel.com>,
	Baruch Siach <baruch@tkos.co.il>,
	Xudong Chen <xudong.chen@mediatek.com>,
	Lee Jones <lee.jones@linaro.org>,
	Geert Uytterhoeven <geert@linux-m68k.org>,
	Neelesh Gupta <neelegup@linux.vnet.ibm.com>,
	Sachin Kamat <sachin.kamat@samsung.com>,
	Ray Jui <rjui@broadcom.com>,
	linux-arm-kernel@lists.infradead.org
Subject: [PATCH 1/3] i2c: uniphier: add UniPhier FIFO-less I2C driver
Date: Thu, 30 Jul 2015 17:12:20 +0900	[thread overview]
Message-ID: <1438243942-26401-2-git-send-email-yamada.masahiro@socionext.com> (raw)
In-Reply-To: <1438243942-26401-1-git-send-email-yamada.masahiro@socionext.com>

Add support for on-chip I2C controller used on old UniPhier SoCs
such as PH1-LD4, PH1-sLD8, etc..  This adapter is so simple that
it has no FIFO in it.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
---

 drivers/i2c/busses/Kconfig        |   8 +
 drivers/i2c/busses/Makefile       |   1 +
 drivers/i2c/busses/i2c-uniphier.c | 446 ++++++++++++++++++++++++++++++++++++++
 3 files changed, 455 insertions(+)
 create mode 100644 drivers/i2c/busses/i2c-uniphier.c

diff --git a/drivers/i2c/busses/Kconfig b/drivers/i2c/busses/Kconfig
index 577d58d..7073a19 100644
--- a/drivers/i2c/busses/Kconfig
+++ b/drivers/i2c/busses/Kconfig
@@ -885,6 +885,14 @@ config I2C_TEGRA
 	  If you say yes to this option, support will be included for the
 	  I2C controller embedded in NVIDIA Tegra SOCs
 
+config I2C_UNIPHIER
+	tristate "UniPhier FIFO-less I2C controller"
+	depends on ARCH_UNIPHIER
+	help
+	  If you say yes to this option, support will be included for
+	  the UniPhier FIFO-less I2C interface embedded in PH1-LD4, PH1-sLD8,
+	  or older UniPhier SoCs.
+
 config I2C_VERSATILE
 	tristate "ARM Versatile/Realview I2C bus support"
 	depends on ARCH_VERSATILE || ARCH_REALVIEW || ARCH_VEXPRESS
diff --git a/drivers/i2c/busses/Makefile b/drivers/i2c/busses/Makefile
index e5f537c..e89969c 100644
--- a/drivers/i2c/busses/Makefile
+++ b/drivers/i2c/busses/Makefile
@@ -85,6 +85,7 @@ obj-$(CONFIG_I2C_ST)		+= i2c-st.o
 obj-$(CONFIG_I2C_STU300)	+= i2c-stu300.o
 obj-$(CONFIG_I2C_SUN6I_P2WI)	+= i2c-sun6i-p2wi.o
 obj-$(CONFIG_I2C_TEGRA)		+= i2c-tegra.o
+obj-$(CONFIG_I2C_UNIPHIER)	+= i2c-uniphier.o
 obj-$(CONFIG_I2C_VERSATILE)	+= i2c-versatile.o
 obj-$(CONFIG_I2C_WMT)		+= i2c-wmt.o
 obj-$(CONFIG_I2C_OCTEON)	+= i2c-octeon.o
diff --git a/drivers/i2c/busses/i2c-uniphier.c b/drivers/i2c/busses/i2c-uniphier.c
new file mode 100644
index 0000000..bd9877f
--- /dev/null
+++ b/drivers/i2c/busses/i2c-uniphier.c
@@ -0,0 +1,446 @@
+/*
+ * Copyright (C) 2015 Masahiro Yamada <yamada.masahiro@socionext.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ */
+
+#include <linux/clk.h>
+#include <linux/i2c.h>
+#include <linux/interrupt.h>
+#include <linux/io.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+
+#define UNIPHIER_I2C_DTRM	0x00	/* TX register */
+#define     UNIPHIER_I2C_DTRM_IRQEN	BIT(11)	/* enable interrupt */
+#define     UNIPHIER_I2C_DTRM_STA	BIT(10)	/* start condition */
+#define     UNIPHIER_I2C_DTRM_STO	BIT(9)	/* stop condition */
+#define     UNIPHIER_I2C_DTRM_NACK	BIT(8)	/* do not return ACK */
+#define     UNIPHIER_I2C_DTRM_RD	BIT(0)	/* read transaction */
+#define UNIPHIER_I2C_DREC	0x04	/* RX register */
+#define     UNIPHIER_I2C_DREC_MST	BIT(14)	/* 1 = master, 0 = slave */
+#define     UNIPHIER_I2C_DREC_TX	BIT(13)	/* 1 = transmit, 0 = receive */
+#define     UNIPHIER_I2C_DREC_STS	BIT(12)	/* stop condition detected */
+#define     UNIPHIER_I2C_DREC_LRB	BIT(11)	/* no ACK */
+#define     UNIPHIER_I2C_DREC_LAB	BIT(9)	/* arbitration lost */
+#define     UNIPHIER_I2C_DREC_BBN	BIT(8)	/* bus not busy */
+#define UNIPHIER_I2C_MYAD	0x08	/* slave address */
+#define UNIPHIER_I2C_CLK	0x0c	/* clock frequency control */
+#define UNIPHIER_I2C_BRST	0x10	/* bus reset */
+#define     UNIPHIER_I2C_BRST_FOEN	BIT(1)	/* normal operation */
+#define     UNIPHIER_I2C_BRST_RSCL	BIT(0)	/* release SCL */
+#define UNIPHIER_I2C_HOLD	0x14	/* hold time control */
+#define UNIPHIER_I2C_BSTS	0x18	/* bus status monitor */
+#define     UNIPHIER_I2C_BSTS_SDA	BIT(1)	/* readback of SDA line */
+#define     UNIPHIER_I2C_BSTS_SCL	BIT(0)	/* readback of SCL line */
+#define UNIPHIER_I2C_NOISE	0x1c	/* noise filter control */
+#define UNIPHIER_I2C_SETUP	0x20	/* setup time control */
+
+#define UNIPHIER_I2C_DEFAULT_SPEED	100000
+#define UNIPHIER_I2C_MAX_SPEED		400000
+
+struct uniphier_i2c_priv {
+	struct completion comp;
+	struct i2c_adapter adap;
+	void __iomem *membase;
+	struct clk *clk;
+	unsigned int busy_cnt;
+};
+
+static irqreturn_t uniphier_i2c_interrupt(int irq, void *dev_id)
+{
+	struct uniphier_i2c_priv *priv = dev_id;
+
+	/*
+	 * This hardware uses edge triggered interrupt.  Do not touch the
+	 * hardware registers in this handler to make sure to catch the next
+	 * interrupt edge.  Just send a complete signal and return.
+	 */
+	complete(&priv->comp);
+
+	return IRQ_HANDLED;
+}
+
+static int uniphier_i2c_xfer_byte(struct i2c_adapter *adap, u32 txdata,
+				  u32 *rxdatap)
+{
+	struct uniphier_i2c_priv *priv = i2c_get_adapdata(adap);
+	unsigned long time_left;
+	u32 rxdata;
+
+	reinit_completion(&priv->comp);
+
+	txdata |= UNIPHIER_I2C_DTRM_IRQEN;
+	dev_dbg(&adap->dev, "write data: 0x%04x\n", txdata);
+	writel(txdata, priv->membase + UNIPHIER_I2C_DTRM);
+
+	time_left = wait_for_completion_timeout(&priv->comp, adap->timeout);
+	if (unlikely(!time_left)) {
+		dev_err(&adap->dev, "transaction timeout\n");
+		return -ETIMEDOUT;
+	}
+
+	rxdata = readl(priv->membase + UNIPHIER_I2C_DREC);
+	dev_dbg(&adap->dev, "read data: 0x%04x\n", rxdata);
+
+	if (rxdatap)
+		*rxdatap = rxdata;
+
+	return 0;
+}
+
+static int uniphier_i2c_send_byte(struct i2c_adapter *adap, u32 txdata)
+{
+	u32 rxdata;
+	int ret;
+
+	ret = uniphier_i2c_xfer_byte(adap, txdata, &rxdata);
+	if (ret)
+		return ret;
+
+	if (unlikely(rxdata & UNIPHIER_I2C_DREC_LAB)) {
+		dev_dbg(&adap->dev, "arbitration lost\n");
+		return -EAGAIN;
+	}
+	if (unlikely(rxdata & UNIPHIER_I2C_DREC_LRB)) {
+		dev_dbg(&adap->dev, "could not get ACK\n");
+		return -ENXIO;
+	}
+
+	return 0;
+}
+
+static int uniphier_i2c_tx(struct i2c_adapter *adap, u16 addr, u16 len,
+			   const u8 *buf)
+{
+	int ret;
+
+	dev_dbg(&adap->dev, "start condition\n");
+	ret = uniphier_i2c_send_byte(adap, addr << 1 |
+				     UNIPHIER_I2C_DTRM_STA |
+				     UNIPHIER_I2C_DTRM_NACK);
+	if (ret)
+		return ret;
+
+	while (len--) {
+		ret = uniphier_i2c_send_byte(adap,
+					     UNIPHIER_I2C_DTRM_NACK | *buf++);
+		if (ret)
+			return ret;
+	}
+
+	return 0;
+}
+
+static int uniphier_i2c_rx(struct i2c_adapter *adap, u16 addr, u16 len,
+			   u8 *buf)
+{
+	int ret;
+
+	dev_dbg(&adap->dev, "start condition\n");
+	ret = uniphier_i2c_send_byte(adap, addr << 1 |
+				     UNIPHIER_I2C_DTRM_STA |
+				     UNIPHIER_I2C_DTRM_NACK |
+				     UNIPHIER_I2C_DTRM_RD);
+	if (ret)
+		return ret;
+
+	while (len--) {
+		u32 rxdata;
+
+		ret = uniphier_i2c_xfer_byte(adap,
+					     len ? 0 : UNIPHIER_I2C_DTRM_NACK,
+					     &rxdata);
+		if (ret)
+			return ret;
+		*buf++ = rxdata;
+	}
+
+	return 0;
+}
+
+static int uniphier_i2c_stop(struct i2c_adapter *adap)
+{
+	dev_dbg(&adap->dev, "stop condition\n");
+	return uniphier_i2c_send_byte(adap, UNIPHIER_I2C_DTRM_STO |
+				      UNIPHIER_I2C_DTRM_NACK);
+}
+
+static int uniphier_i2c_master_xfer_one(struct i2c_adapter *adap,
+					struct i2c_msg *msg, bool stop)
+{
+	bool is_read = msg->flags & I2C_M_RD;
+	bool recovery = false;
+	int ret;
+
+	dev_dbg(&adap->dev, "%s: addr=0x%02x, len=%d, stop=%d\n",
+		is_read ? "receive" : "transmit", msg->addr, msg->len, stop);
+
+	if (is_read)
+		ret = uniphier_i2c_rx(adap, msg->addr, msg->len, msg->buf);
+	else
+		ret = uniphier_i2c_tx(adap, msg->addr, msg->len, msg->buf);
+
+	if (ret == -EAGAIN) /* could not acquire bus. bail out without STOP */
+		return ret;
+
+	if (ret == -ETIMEDOUT) {
+		/* This error is fatal.  Needs recovery. */
+		stop = false;
+		recovery = true;
+	}
+
+	if (stop) {
+		int ret2 = uniphier_i2c_stop(adap);
+
+		if (ret2) {
+			/* Failed to issue STOP.  The bus needs recovery. */
+			recovery = true;
+			ret = ret ?: ret2;
+		}
+	}
+
+	if (recovery)
+		i2c_recover_bus(adap);
+
+	return ret;
+}
+
+static int uniphier_i2c_check_bus_busy(struct i2c_adapter *adap)
+{
+	struct uniphier_i2c_priv *priv = i2c_get_adapdata(adap);
+
+	if (!(readl(priv->membase + UNIPHIER_I2C_DREC) &
+						UNIPHIER_I2C_DREC_BBN)) {
+		if (priv->busy_cnt++ > 3) {
+			/*
+			 * If bus busy continues too long, it is probably
+			 * in a wrong state.  Try bus recovery.
+			 */
+			i2c_recover_bus(adap);
+			priv->busy_cnt = 0;
+		}
+
+		return -EAGAIN;
+	}
+
+	priv->busy_cnt = 0;
+	return 0;
+}
+
+static int uniphier_i2c_master_xfer(struct i2c_adapter *adap,
+				    struct i2c_msg *msgs, int num)
+{
+	struct i2c_msg *msg, *emsg = msgs + num;
+	int ret;
+
+	ret = uniphier_i2c_check_bus_busy(adap);
+	if (ret)
+		return ret;
+
+	for (msg = msgs; msg < emsg; msg++) {
+		/* If next message is read, skip the stop condition */
+		bool stop = !(msg + 1 < emsg && msg[1].flags & I2C_M_RD);
+		/* but, force it if I2C_M_STOP is set */
+		if (msg->flags & I2C_M_STOP)
+			stop = true;
+
+		ret = uniphier_i2c_master_xfer_one(adap, msg, stop);
+		if (ret)
+			return ret;
+	}
+
+	return num;
+}
+
+static u32 uniphier_i2c_functionality(struct i2c_adapter *adap)
+{
+	return I2C_FUNC_I2C;
+}
+
+static const struct i2c_algorithm uniphier_i2c_algo = {
+	.master_xfer = uniphier_i2c_master_xfer,
+	.functionality = uniphier_i2c_functionality,
+};
+
+static void uniphier_i2c_reset(struct uniphier_i2c_priv *priv, bool reset_on)
+{
+	u32 val = UNIPHIER_I2C_BRST_RSCL;
+
+	val |= reset_on ? 0 : UNIPHIER_I2C_BRST_FOEN;
+	writel(val, priv->membase + UNIPHIER_I2C_BRST);
+}
+
+static int uniphier_i2c_get_scl(struct i2c_adapter *adap)
+{
+	struct uniphier_i2c_priv *priv = i2c_get_adapdata(adap);
+
+	return !!(readl(priv->membase + UNIPHIER_I2C_BSTS) &
+							UNIPHIER_I2C_BSTS_SCL);
+}
+
+static void uniphier_i2c_set_scl(struct i2c_adapter *adap, int val)
+{
+	struct uniphier_i2c_priv *priv = i2c_get_adapdata(adap);
+
+	writel(val ? UNIPHIER_I2C_BRST_RSCL : 0,
+	       priv->membase + UNIPHIER_I2C_BRST);
+}
+
+static int uniphier_i2c_get_sda(struct i2c_adapter *adap)
+{
+	struct uniphier_i2c_priv *priv = i2c_get_adapdata(adap);
+
+	return !!(readl(priv->membase + UNIPHIER_I2C_BSTS) &
+							UNIPHIER_I2C_BSTS_SDA);
+}
+
+static void uniphier_i2c_unprepare_recovery(struct i2c_adapter *adap)
+{
+	uniphier_i2c_reset(i2c_get_adapdata(adap), false);
+}
+
+static struct i2c_bus_recovery_info uniphier_i2c_bus_recovery_info = {
+	.recover_bus = i2c_generic_scl_recovery,
+	.get_scl = uniphier_i2c_get_scl,
+	.set_scl = uniphier_i2c_set_scl,
+	.get_sda = uniphier_i2c_get_sda,
+	.unprepare_recovery = uniphier_i2c_unprepare_recovery,
+};
+
+static int uniphier_i2c_clk_init(struct device *dev,
+				 struct uniphier_i2c_priv *priv)
+{
+	struct device_node *np = dev->of_node;
+	unsigned long clk_rate;
+	u32 bus_speed;
+	int ret;
+
+	if (of_property_read_u32(np, "clock-frequency", &bus_speed))
+		bus_speed = UNIPHIER_I2C_DEFAULT_SPEED;
+
+	if (bus_speed > UNIPHIER_I2C_MAX_SPEED)
+		bus_speed = UNIPHIER_I2C_MAX_SPEED;
+
+	/* Get input clk rate through clk driver */
+	priv->clk = devm_clk_get(dev, NULL);
+	if (IS_ERR(priv->clk)) {
+		dev_err(dev, "failed to get clock\n");
+		return PTR_ERR(priv->clk);
+	}
+
+	ret = clk_prepare_enable(priv->clk);
+	if (ret)
+		return ret;
+
+	clk_rate = clk_get_rate(priv->clk);
+
+	uniphier_i2c_reset(priv, true);
+
+	writel((clk_rate / bus_speed / 2 << 16) | (clk_rate / bus_speed),
+	       priv->membase + UNIPHIER_I2C_CLK);
+
+	uniphier_i2c_reset(priv, false);
+
+	return 0;
+}
+
+static int uniphier_i2c_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct uniphier_i2c_priv *priv;
+	struct resource *regs;
+	int irq;
+	int ret;
+
+	priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
+	if (!priv)
+		return -ENOMEM;
+
+	regs = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	if (!regs) {
+		dev_err(dev, "failed to get memory resource");
+		return -EINVAL;
+	}
+
+	priv->membase = devm_ioremap_resource(dev, regs);
+	if (IS_ERR(priv->membase))
+		return PTR_ERR(priv->membase);
+
+	irq = platform_get_irq(pdev, 0);
+	if (irq < 0) {
+		dev_err(dev, "failed to get IRQ number");
+		return irq;
+	}
+
+	init_completion(&priv->comp);
+	priv->adap.owner = THIS_MODULE;
+	priv->adap.algo = &uniphier_i2c_algo;
+	priv->adap.dev.parent = dev;
+	priv->adap.dev.of_node = dev->of_node;
+	strlcpy(priv->adap.name, "UniPhier I2C", sizeof(priv->adap.name));
+	priv->adap.bus_recovery_info = &uniphier_i2c_bus_recovery_info;
+	i2c_set_adapdata(&priv->adap, priv);
+	platform_set_drvdata(pdev, priv);
+
+	ret = uniphier_i2c_clk_init(dev, priv);
+	if (ret)
+		return ret;
+
+	ret = devm_request_irq(dev, irq, uniphier_i2c_interrupt, 0, pdev->name,
+			       priv);
+	if (ret) {
+		dev_err(dev, "failed to request irq %d\n", irq);
+		goto err;
+	}
+
+	ret = i2c_add_adapter(&priv->adap);
+	if (ret) {
+		dev_err(dev, "failed to add I2C adapter\n");
+		goto err;
+	}
+
+err:
+	if (ret)
+		clk_disable_unprepare(priv->clk);
+
+	return ret;
+}
+
+static int uniphier_i2c_remove(struct platform_device *pdev)
+{
+	struct uniphier_i2c_priv *priv = platform_get_drvdata(pdev);
+
+	i2c_del_adapter(&priv->adap);
+	clk_disable_unprepare(priv->clk);
+
+	return 0;
+}
+
+static const struct of_device_id uniphier_i2c_match[] = {
+	{ .compatible = "socionext,uniphier-i2c" },
+	{ /* sentinel */ }
+};
+MODULE_DEVICE_TABLE(of, uniphier_i2c_match);
+
+static struct platform_driver uniphier_i2c_drv = {
+	.probe  = uniphier_i2c_probe,
+	.remove = uniphier_i2c_remove,
+	.driver = {
+		.name  = "uniphier-i2c",
+		.of_match_table = uniphier_i2c_match,
+	},
+};
+module_platform_driver(uniphier_i2c_drv);
+
+MODULE_DESCRIPTION("UniPhier I2C bus driver");
+MODULE_AUTHOR("Masahiro Yamada <yamada.masahiro@socionext.com>");
+MODULE_LICENSE("GPL");
-- 
1.9.1


WARNING: multiple messages have this Message-ID (diff)
From: Masahiro Yamada <yamada.masahiro@socionext.com>
To: linux-i2c@vger.kernel.org
Cc: Laurentiu Palcu <laurentiu.palcu@intel.com>,
	Xudong Chen <xudong.chen@mediatek.com>,
	Baruch Siach <baruch@tkos.co.il>,
	Zubair Lutfullah Kakakhel <Zubair.Kakakhel@imgtec.com>,
	Masahiro Yamada <yamada.masahiro@socionext.com>,
	Andrew Bresticker <abrestic@chromium.org>,
	Lee Jones <lee.jones@linaro.org>,
	Max Schwarz <max.schwarz@online.de>,
	linux-kernel@vger.kernel.org, Ray Jui <rjui@broadcom.com>,
	Sachin Kamat <sachin.kamat@samsung.com>,
	Wei Yan <sledge.yanwei@huawei.com>,
	Anders Berg <anders.berg@avagotech.com>,
	Geert Uytterhoeven <geert@linux-m68k.org>,
	Kamal Dasu <kdasu.kdev@gmail.com>,
	David Box <david.e.box@linux.intel.com>,
	Wolfram Sang <wsa@the-dreams.de>,
	Neelesh Gupta <neelegup@linux.vnet.ibm.com>,
	Mika Westerberg <mika.westerberg@linux.intel.com>,
	linux-arm-kernel@lists.infradead.org
Subject: [PATCH 1/3] i2c: uniphier: add UniPhier FIFO-less I2C driver
Date: Thu, 30 Jul 2015 17:12:20 +0900	[thread overview]
Message-ID: <1438243942-26401-2-git-send-email-yamada.masahiro@socionext.com> (raw)
In-Reply-To: <1438243942-26401-1-git-send-email-yamada.masahiro@socionext.com>

Add support for on-chip I2C controller used on old UniPhier SoCs
such as PH1-LD4, PH1-sLD8, etc..  This adapter is so simple that
it has no FIFO in it.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
---

 drivers/i2c/busses/Kconfig        |   8 +
 drivers/i2c/busses/Makefile       |   1 +
 drivers/i2c/busses/i2c-uniphier.c | 446 ++++++++++++++++++++++++++++++++++++++
 3 files changed, 455 insertions(+)
 create mode 100644 drivers/i2c/busses/i2c-uniphier.c

diff --git a/drivers/i2c/busses/Kconfig b/drivers/i2c/busses/Kconfig
index 577d58d..7073a19 100644
--- a/drivers/i2c/busses/Kconfig
+++ b/drivers/i2c/busses/Kconfig
@@ -885,6 +885,14 @@ config I2C_TEGRA
 	  If you say yes to this option, support will be included for the
 	  I2C controller embedded in NVIDIA Tegra SOCs
 
+config I2C_UNIPHIER
+	tristate "UniPhier FIFO-less I2C controller"
+	depends on ARCH_UNIPHIER
+	help
+	  If you say yes to this option, support will be included for
+	  the UniPhier FIFO-less I2C interface embedded in PH1-LD4, PH1-sLD8,
+	  or older UniPhier SoCs.
+
 config I2C_VERSATILE
 	tristate "ARM Versatile/Realview I2C bus support"
 	depends on ARCH_VERSATILE || ARCH_REALVIEW || ARCH_VEXPRESS
diff --git a/drivers/i2c/busses/Makefile b/drivers/i2c/busses/Makefile
index e5f537c..e89969c 100644
--- a/drivers/i2c/busses/Makefile
+++ b/drivers/i2c/busses/Makefile
@@ -85,6 +85,7 @@ obj-$(CONFIG_I2C_ST)		+= i2c-st.o
 obj-$(CONFIG_I2C_STU300)	+= i2c-stu300.o
 obj-$(CONFIG_I2C_SUN6I_P2WI)	+= i2c-sun6i-p2wi.o
 obj-$(CONFIG_I2C_TEGRA)		+= i2c-tegra.o
+obj-$(CONFIG_I2C_UNIPHIER)	+= i2c-uniphier.o
 obj-$(CONFIG_I2C_VERSATILE)	+= i2c-versatile.o
 obj-$(CONFIG_I2C_WMT)		+= i2c-wmt.o
 obj-$(CONFIG_I2C_OCTEON)	+= i2c-octeon.o
diff --git a/drivers/i2c/busses/i2c-uniphier.c b/drivers/i2c/busses/i2c-uniphier.c
new file mode 100644
index 0000000..bd9877f
--- /dev/null
+++ b/drivers/i2c/busses/i2c-uniphier.c
@@ -0,0 +1,446 @@
+/*
+ * Copyright (C) 2015 Masahiro Yamada <yamada.masahiro@socionext.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ */
+
+#include <linux/clk.h>
+#include <linux/i2c.h>
+#include <linux/interrupt.h>
+#include <linux/io.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+
+#define UNIPHIER_I2C_DTRM	0x00	/* TX register */
+#define     UNIPHIER_I2C_DTRM_IRQEN	BIT(11)	/* enable interrupt */
+#define     UNIPHIER_I2C_DTRM_STA	BIT(10)	/* start condition */
+#define     UNIPHIER_I2C_DTRM_STO	BIT(9)	/* stop condition */
+#define     UNIPHIER_I2C_DTRM_NACK	BIT(8)	/* do not return ACK */
+#define     UNIPHIER_I2C_DTRM_RD	BIT(0)	/* read transaction */
+#define UNIPHIER_I2C_DREC	0x04	/* RX register */
+#define     UNIPHIER_I2C_DREC_MST	BIT(14)	/* 1 = master, 0 = slave */
+#define     UNIPHIER_I2C_DREC_TX	BIT(13)	/* 1 = transmit, 0 = receive */
+#define     UNIPHIER_I2C_DREC_STS	BIT(12)	/* stop condition detected */
+#define     UNIPHIER_I2C_DREC_LRB	BIT(11)	/* no ACK */
+#define     UNIPHIER_I2C_DREC_LAB	BIT(9)	/* arbitration lost */
+#define     UNIPHIER_I2C_DREC_BBN	BIT(8)	/* bus not busy */
+#define UNIPHIER_I2C_MYAD	0x08	/* slave address */
+#define UNIPHIER_I2C_CLK	0x0c	/* clock frequency control */
+#define UNIPHIER_I2C_BRST	0x10	/* bus reset */
+#define     UNIPHIER_I2C_BRST_FOEN	BIT(1)	/* normal operation */
+#define     UNIPHIER_I2C_BRST_RSCL	BIT(0)	/* release SCL */
+#define UNIPHIER_I2C_HOLD	0x14	/* hold time control */
+#define UNIPHIER_I2C_BSTS	0x18	/* bus status monitor */
+#define     UNIPHIER_I2C_BSTS_SDA	BIT(1)	/* readback of SDA line */
+#define     UNIPHIER_I2C_BSTS_SCL	BIT(0)	/* readback of SCL line */
+#define UNIPHIER_I2C_NOISE	0x1c	/* noise filter control */
+#define UNIPHIER_I2C_SETUP	0x20	/* setup time control */
+
+#define UNIPHIER_I2C_DEFAULT_SPEED	100000
+#define UNIPHIER_I2C_MAX_SPEED		400000
+
+struct uniphier_i2c_priv {
+	struct completion comp;
+	struct i2c_adapter adap;
+	void __iomem *membase;
+	struct clk *clk;
+	unsigned int busy_cnt;
+};
+
+static irqreturn_t uniphier_i2c_interrupt(int irq, void *dev_id)
+{
+	struct uniphier_i2c_priv *priv = dev_id;
+
+	/*
+	 * This hardware uses edge triggered interrupt.  Do not touch the
+	 * hardware registers in this handler to make sure to catch the next
+	 * interrupt edge.  Just send a complete signal and return.
+	 */
+	complete(&priv->comp);
+
+	return IRQ_HANDLED;
+}
+
+static int uniphier_i2c_xfer_byte(struct i2c_adapter *adap, u32 txdata,
+				  u32 *rxdatap)
+{
+	struct uniphier_i2c_priv *priv = i2c_get_adapdata(adap);
+	unsigned long time_left;
+	u32 rxdata;
+
+	reinit_completion(&priv->comp);
+
+	txdata |= UNIPHIER_I2C_DTRM_IRQEN;
+	dev_dbg(&adap->dev, "write data: 0x%04x\n", txdata);
+	writel(txdata, priv->membase + UNIPHIER_I2C_DTRM);
+
+	time_left = wait_for_completion_timeout(&priv->comp, adap->timeout);
+	if (unlikely(!time_left)) {
+		dev_err(&adap->dev, "transaction timeout\n");
+		return -ETIMEDOUT;
+	}
+
+	rxdata = readl(priv->membase + UNIPHIER_I2C_DREC);
+	dev_dbg(&adap->dev, "read data: 0x%04x\n", rxdata);
+
+	if (rxdatap)
+		*rxdatap = rxdata;
+
+	return 0;
+}
+
+static int uniphier_i2c_send_byte(struct i2c_adapter *adap, u32 txdata)
+{
+	u32 rxdata;
+	int ret;
+
+	ret = uniphier_i2c_xfer_byte(adap, txdata, &rxdata);
+	if (ret)
+		return ret;
+
+	if (unlikely(rxdata & UNIPHIER_I2C_DREC_LAB)) {
+		dev_dbg(&adap->dev, "arbitration lost\n");
+		return -EAGAIN;
+	}
+	if (unlikely(rxdata & UNIPHIER_I2C_DREC_LRB)) {
+		dev_dbg(&adap->dev, "could not get ACK\n");
+		return -ENXIO;
+	}
+
+	return 0;
+}
+
+static int uniphier_i2c_tx(struct i2c_adapter *adap, u16 addr, u16 len,
+			   const u8 *buf)
+{
+	int ret;
+
+	dev_dbg(&adap->dev, "start condition\n");
+	ret = uniphier_i2c_send_byte(adap, addr << 1 |
+				     UNIPHIER_I2C_DTRM_STA |
+				     UNIPHIER_I2C_DTRM_NACK);
+	if (ret)
+		return ret;
+
+	while (len--) {
+		ret = uniphier_i2c_send_byte(adap,
+					     UNIPHIER_I2C_DTRM_NACK | *buf++);
+		if (ret)
+			return ret;
+	}
+
+	return 0;
+}
+
+static int uniphier_i2c_rx(struct i2c_adapter *adap, u16 addr, u16 len,
+			   u8 *buf)
+{
+	int ret;
+
+	dev_dbg(&adap->dev, "start condition\n");
+	ret = uniphier_i2c_send_byte(adap, addr << 1 |
+				     UNIPHIER_I2C_DTRM_STA |
+				     UNIPHIER_I2C_DTRM_NACK |
+				     UNIPHIER_I2C_DTRM_RD);
+	if (ret)
+		return ret;
+
+	while (len--) {
+		u32 rxdata;
+
+		ret = uniphier_i2c_xfer_byte(adap,
+					     len ? 0 : UNIPHIER_I2C_DTRM_NACK,
+					     &rxdata);
+		if (ret)
+			return ret;
+		*buf++ = rxdata;
+	}
+
+	return 0;
+}
+
+static int uniphier_i2c_stop(struct i2c_adapter *adap)
+{
+	dev_dbg(&adap->dev, "stop condition\n");
+	return uniphier_i2c_send_byte(adap, UNIPHIER_I2C_DTRM_STO |
+				      UNIPHIER_I2C_DTRM_NACK);
+}
+
+static int uniphier_i2c_master_xfer_one(struct i2c_adapter *adap,
+					struct i2c_msg *msg, bool stop)
+{
+	bool is_read = msg->flags & I2C_M_RD;
+	bool recovery = false;
+	int ret;
+
+	dev_dbg(&adap->dev, "%s: addr=0x%02x, len=%d, stop=%d\n",
+		is_read ? "receive" : "transmit", msg->addr, msg->len, stop);
+
+	if (is_read)
+		ret = uniphier_i2c_rx(adap, msg->addr, msg->len, msg->buf);
+	else
+		ret = uniphier_i2c_tx(adap, msg->addr, msg->len, msg->buf);
+
+	if (ret == -EAGAIN) /* could not acquire bus. bail out without STOP */
+		return ret;
+
+	if (ret == -ETIMEDOUT) {
+		/* This error is fatal.  Needs recovery. */
+		stop = false;
+		recovery = true;
+	}
+
+	if (stop) {
+		int ret2 = uniphier_i2c_stop(adap);
+
+		if (ret2) {
+			/* Failed to issue STOP.  The bus needs recovery. */
+			recovery = true;
+			ret = ret ?: ret2;
+		}
+	}
+
+	if (recovery)
+		i2c_recover_bus(adap);
+
+	return ret;
+}
+
+static int uniphier_i2c_check_bus_busy(struct i2c_adapter *adap)
+{
+	struct uniphier_i2c_priv *priv = i2c_get_adapdata(adap);
+
+	if (!(readl(priv->membase + UNIPHIER_I2C_DREC) &
+						UNIPHIER_I2C_DREC_BBN)) {
+		if (priv->busy_cnt++ > 3) {
+			/*
+			 * If bus busy continues too long, it is probably
+			 * in a wrong state.  Try bus recovery.
+			 */
+			i2c_recover_bus(adap);
+			priv->busy_cnt = 0;
+		}
+
+		return -EAGAIN;
+	}
+
+	priv->busy_cnt = 0;
+	return 0;
+}
+
+static int uniphier_i2c_master_xfer(struct i2c_adapter *adap,
+				    struct i2c_msg *msgs, int num)
+{
+	struct i2c_msg *msg, *emsg = msgs + num;
+	int ret;
+
+	ret = uniphier_i2c_check_bus_busy(adap);
+	if (ret)
+		return ret;
+
+	for (msg = msgs; msg < emsg; msg++) {
+		/* If next message is read, skip the stop condition */
+		bool stop = !(msg + 1 < emsg && msg[1].flags & I2C_M_RD);
+		/* but, force it if I2C_M_STOP is set */
+		if (msg->flags & I2C_M_STOP)
+			stop = true;
+
+		ret = uniphier_i2c_master_xfer_one(adap, msg, stop);
+		if (ret)
+			return ret;
+	}
+
+	return num;
+}
+
+static u32 uniphier_i2c_functionality(struct i2c_adapter *adap)
+{
+	return I2C_FUNC_I2C;
+}
+
+static const struct i2c_algorithm uniphier_i2c_algo = {
+	.master_xfer = uniphier_i2c_master_xfer,
+	.functionality = uniphier_i2c_functionality,
+};
+
+static void uniphier_i2c_reset(struct uniphier_i2c_priv *priv, bool reset_on)
+{
+	u32 val = UNIPHIER_I2C_BRST_RSCL;
+
+	val |= reset_on ? 0 : UNIPHIER_I2C_BRST_FOEN;
+	writel(val, priv->membase + UNIPHIER_I2C_BRST);
+}
+
+static int uniphier_i2c_get_scl(struct i2c_adapter *adap)
+{
+	struct uniphier_i2c_priv *priv = i2c_get_adapdata(adap);
+
+	return !!(readl(priv->membase + UNIPHIER_I2C_BSTS) &
+							UNIPHIER_I2C_BSTS_SCL);
+}
+
+static void uniphier_i2c_set_scl(struct i2c_adapter *adap, int val)
+{
+	struct uniphier_i2c_priv *priv = i2c_get_adapdata(adap);
+
+	writel(val ? UNIPHIER_I2C_BRST_RSCL : 0,
+	       priv->membase + UNIPHIER_I2C_BRST);
+}
+
+static int uniphier_i2c_get_sda(struct i2c_adapter *adap)
+{
+	struct uniphier_i2c_priv *priv = i2c_get_adapdata(adap);
+
+	return !!(readl(priv->membase + UNIPHIER_I2C_BSTS) &
+							UNIPHIER_I2C_BSTS_SDA);
+}
+
+static void uniphier_i2c_unprepare_recovery(struct i2c_adapter *adap)
+{
+	uniphier_i2c_reset(i2c_get_adapdata(adap), false);
+}
+
+static struct i2c_bus_recovery_info uniphier_i2c_bus_recovery_info = {
+	.recover_bus = i2c_generic_scl_recovery,
+	.get_scl = uniphier_i2c_get_scl,
+	.set_scl = uniphier_i2c_set_scl,
+	.get_sda = uniphier_i2c_get_sda,
+	.unprepare_recovery = uniphier_i2c_unprepare_recovery,
+};
+
+static int uniphier_i2c_clk_init(struct device *dev,
+				 struct uniphier_i2c_priv *priv)
+{
+	struct device_node *np = dev->of_node;
+	unsigned long clk_rate;
+	u32 bus_speed;
+	int ret;
+
+	if (of_property_read_u32(np, "clock-frequency", &bus_speed))
+		bus_speed = UNIPHIER_I2C_DEFAULT_SPEED;
+
+	if (bus_speed > UNIPHIER_I2C_MAX_SPEED)
+		bus_speed = UNIPHIER_I2C_MAX_SPEED;
+
+	/* Get input clk rate through clk driver */
+	priv->clk = devm_clk_get(dev, NULL);
+	if (IS_ERR(priv->clk)) {
+		dev_err(dev, "failed to get clock\n");
+		return PTR_ERR(priv->clk);
+	}
+
+	ret = clk_prepare_enable(priv->clk);
+	if (ret)
+		return ret;
+
+	clk_rate = clk_get_rate(priv->clk);
+
+	uniphier_i2c_reset(priv, true);
+
+	writel((clk_rate / bus_speed / 2 << 16) | (clk_rate / bus_speed),
+	       priv->membase + UNIPHIER_I2C_CLK);
+
+	uniphier_i2c_reset(priv, false);
+
+	return 0;
+}
+
+static int uniphier_i2c_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct uniphier_i2c_priv *priv;
+	struct resource *regs;
+	int irq;
+	int ret;
+
+	priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
+	if (!priv)
+		return -ENOMEM;
+
+	regs = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	if (!regs) {
+		dev_err(dev, "failed to get memory resource");
+		return -EINVAL;
+	}
+
+	priv->membase = devm_ioremap_resource(dev, regs);
+	if (IS_ERR(priv->membase))
+		return PTR_ERR(priv->membase);
+
+	irq = platform_get_irq(pdev, 0);
+	if (irq < 0) {
+		dev_err(dev, "failed to get IRQ number");
+		return irq;
+	}
+
+	init_completion(&priv->comp);
+	priv->adap.owner = THIS_MODULE;
+	priv->adap.algo = &uniphier_i2c_algo;
+	priv->adap.dev.parent = dev;
+	priv->adap.dev.of_node = dev->of_node;
+	strlcpy(priv->adap.name, "UniPhier I2C", sizeof(priv->adap.name));
+	priv->adap.bus_recovery_info = &uniphier_i2c_bus_recovery_info;
+	i2c_set_adapdata(&priv->adap, priv);
+	platform_set_drvdata(pdev, priv);
+
+	ret = uniphier_i2c_clk_init(dev, priv);
+	if (ret)
+		return ret;
+
+	ret = devm_request_irq(dev, irq, uniphier_i2c_interrupt, 0, pdev->name,
+			       priv);
+	if (ret) {
+		dev_err(dev, "failed to request irq %d\n", irq);
+		goto err;
+	}
+
+	ret = i2c_add_adapter(&priv->adap);
+	if (ret) {
+		dev_err(dev, "failed to add I2C adapter\n");
+		goto err;
+	}
+
+err:
+	if (ret)
+		clk_disable_unprepare(priv->clk);
+
+	return ret;
+}
+
+static int uniphier_i2c_remove(struct platform_device *pdev)
+{
+	struct uniphier_i2c_priv *priv = platform_get_drvdata(pdev);
+
+	i2c_del_adapter(&priv->adap);
+	clk_disable_unprepare(priv->clk);
+
+	return 0;
+}
+
+static const struct of_device_id uniphier_i2c_match[] = {
+	{ .compatible = "socionext,uniphier-i2c" },
+	{ /* sentinel */ }
+};
+MODULE_DEVICE_TABLE(of, uniphier_i2c_match);
+
+static struct platform_driver uniphier_i2c_drv = {
+	.probe  = uniphier_i2c_probe,
+	.remove = uniphier_i2c_remove,
+	.driver = {
+		.name  = "uniphier-i2c",
+		.of_match_table = uniphier_i2c_match,
+	},
+};
+module_platform_driver(uniphier_i2c_drv);
+
+MODULE_DESCRIPTION("UniPhier I2C bus driver");
+MODULE_AUTHOR("Masahiro Yamada <yamada.masahiro@socionext.com>");
+MODULE_LICENSE("GPL");
-- 
1.9.1

WARNING: multiple messages have this Message-ID (diff)
From: yamada.masahiro@socionext.com (Masahiro Yamada)
To: linux-arm-kernel@lists.infradead.org
Subject: [PATCH 1/3] i2c: uniphier: add UniPhier FIFO-less I2C driver
Date: Thu, 30 Jul 2015 17:12:20 +0900	[thread overview]
Message-ID: <1438243942-26401-2-git-send-email-yamada.masahiro@socionext.com> (raw)
In-Reply-To: <1438243942-26401-1-git-send-email-yamada.masahiro@socionext.com>

Add support for on-chip I2C controller used on old UniPhier SoCs
such as PH1-LD4, PH1-sLD8, etc..  This adapter is so simple that
it has no FIFO in it.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
---

 drivers/i2c/busses/Kconfig        |   8 +
 drivers/i2c/busses/Makefile       |   1 +
 drivers/i2c/busses/i2c-uniphier.c | 446 ++++++++++++++++++++++++++++++++++++++
 3 files changed, 455 insertions(+)
 create mode 100644 drivers/i2c/busses/i2c-uniphier.c

diff --git a/drivers/i2c/busses/Kconfig b/drivers/i2c/busses/Kconfig
index 577d58d..7073a19 100644
--- a/drivers/i2c/busses/Kconfig
+++ b/drivers/i2c/busses/Kconfig
@@ -885,6 +885,14 @@ config I2C_TEGRA
 	  If you say yes to this option, support will be included for the
 	  I2C controller embedded in NVIDIA Tegra SOCs
 
+config I2C_UNIPHIER
+	tristate "UniPhier FIFO-less I2C controller"
+	depends on ARCH_UNIPHIER
+	help
+	  If you say yes to this option, support will be included for
+	  the UniPhier FIFO-less I2C interface embedded in PH1-LD4, PH1-sLD8,
+	  or older UniPhier SoCs.
+
 config I2C_VERSATILE
 	tristate "ARM Versatile/Realview I2C bus support"
 	depends on ARCH_VERSATILE || ARCH_REALVIEW || ARCH_VEXPRESS
diff --git a/drivers/i2c/busses/Makefile b/drivers/i2c/busses/Makefile
index e5f537c..e89969c 100644
--- a/drivers/i2c/busses/Makefile
+++ b/drivers/i2c/busses/Makefile
@@ -85,6 +85,7 @@ obj-$(CONFIG_I2C_ST)		+= i2c-st.o
 obj-$(CONFIG_I2C_STU300)	+= i2c-stu300.o
 obj-$(CONFIG_I2C_SUN6I_P2WI)	+= i2c-sun6i-p2wi.o
 obj-$(CONFIG_I2C_TEGRA)		+= i2c-tegra.o
+obj-$(CONFIG_I2C_UNIPHIER)	+= i2c-uniphier.o
 obj-$(CONFIG_I2C_VERSATILE)	+= i2c-versatile.o
 obj-$(CONFIG_I2C_WMT)		+= i2c-wmt.o
 obj-$(CONFIG_I2C_OCTEON)	+= i2c-octeon.o
diff --git a/drivers/i2c/busses/i2c-uniphier.c b/drivers/i2c/busses/i2c-uniphier.c
new file mode 100644
index 0000000..bd9877f
--- /dev/null
+++ b/drivers/i2c/busses/i2c-uniphier.c
@@ -0,0 +1,446 @@
+/*
+ * Copyright (C) 2015 Masahiro Yamada <yamada.masahiro@socionext.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ */
+
+#include <linux/clk.h>
+#include <linux/i2c.h>
+#include <linux/interrupt.h>
+#include <linux/io.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+
+#define UNIPHIER_I2C_DTRM	0x00	/* TX register */
+#define     UNIPHIER_I2C_DTRM_IRQEN	BIT(11)	/* enable interrupt */
+#define     UNIPHIER_I2C_DTRM_STA	BIT(10)	/* start condition */
+#define     UNIPHIER_I2C_DTRM_STO	BIT(9)	/* stop condition */
+#define     UNIPHIER_I2C_DTRM_NACK	BIT(8)	/* do not return ACK */
+#define     UNIPHIER_I2C_DTRM_RD	BIT(0)	/* read transaction */
+#define UNIPHIER_I2C_DREC	0x04	/* RX register */
+#define     UNIPHIER_I2C_DREC_MST	BIT(14)	/* 1 = master, 0 = slave */
+#define     UNIPHIER_I2C_DREC_TX	BIT(13)	/* 1 = transmit, 0 = receive */
+#define     UNIPHIER_I2C_DREC_STS	BIT(12)	/* stop condition detected */
+#define     UNIPHIER_I2C_DREC_LRB	BIT(11)	/* no ACK */
+#define     UNIPHIER_I2C_DREC_LAB	BIT(9)	/* arbitration lost */
+#define     UNIPHIER_I2C_DREC_BBN	BIT(8)	/* bus not busy */
+#define UNIPHIER_I2C_MYAD	0x08	/* slave address */
+#define UNIPHIER_I2C_CLK	0x0c	/* clock frequency control */
+#define UNIPHIER_I2C_BRST	0x10	/* bus reset */
+#define     UNIPHIER_I2C_BRST_FOEN	BIT(1)	/* normal operation */
+#define     UNIPHIER_I2C_BRST_RSCL	BIT(0)	/* release SCL */
+#define UNIPHIER_I2C_HOLD	0x14	/* hold time control */
+#define UNIPHIER_I2C_BSTS	0x18	/* bus status monitor */
+#define     UNIPHIER_I2C_BSTS_SDA	BIT(1)	/* readback of SDA line */
+#define     UNIPHIER_I2C_BSTS_SCL	BIT(0)	/* readback of SCL line */
+#define UNIPHIER_I2C_NOISE	0x1c	/* noise filter control */
+#define UNIPHIER_I2C_SETUP	0x20	/* setup time control */
+
+#define UNIPHIER_I2C_DEFAULT_SPEED	100000
+#define UNIPHIER_I2C_MAX_SPEED		400000
+
+struct uniphier_i2c_priv {
+	struct completion comp;
+	struct i2c_adapter adap;
+	void __iomem *membase;
+	struct clk *clk;
+	unsigned int busy_cnt;
+};
+
+static irqreturn_t uniphier_i2c_interrupt(int irq, void *dev_id)
+{
+	struct uniphier_i2c_priv *priv = dev_id;
+
+	/*
+	 * This hardware uses edge triggered interrupt.  Do not touch the
+	 * hardware registers in this handler to make sure to catch the next
+	 * interrupt edge.  Just send a complete signal and return.
+	 */
+	complete(&priv->comp);
+
+	return IRQ_HANDLED;
+}
+
+static int uniphier_i2c_xfer_byte(struct i2c_adapter *adap, u32 txdata,
+				  u32 *rxdatap)
+{
+	struct uniphier_i2c_priv *priv = i2c_get_adapdata(adap);
+	unsigned long time_left;
+	u32 rxdata;
+
+	reinit_completion(&priv->comp);
+
+	txdata |= UNIPHIER_I2C_DTRM_IRQEN;
+	dev_dbg(&adap->dev, "write data: 0x%04x\n", txdata);
+	writel(txdata, priv->membase + UNIPHIER_I2C_DTRM);
+
+	time_left = wait_for_completion_timeout(&priv->comp, adap->timeout);
+	if (unlikely(!time_left)) {
+		dev_err(&adap->dev, "transaction timeout\n");
+		return -ETIMEDOUT;
+	}
+
+	rxdata = readl(priv->membase + UNIPHIER_I2C_DREC);
+	dev_dbg(&adap->dev, "read data: 0x%04x\n", rxdata);
+
+	if (rxdatap)
+		*rxdatap = rxdata;
+
+	return 0;
+}
+
+static int uniphier_i2c_send_byte(struct i2c_adapter *adap, u32 txdata)
+{
+	u32 rxdata;
+	int ret;
+
+	ret = uniphier_i2c_xfer_byte(adap, txdata, &rxdata);
+	if (ret)
+		return ret;
+
+	if (unlikely(rxdata & UNIPHIER_I2C_DREC_LAB)) {
+		dev_dbg(&adap->dev, "arbitration lost\n");
+		return -EAGAIN;
+	}
+	if (unlikely(rxdata & UNIPHIER_I2C_DREC_LRB)) {
+		dev_dbg(&adap->dev, "could not get ACK\n");
+		return -ENXIO;
+	}
+
+	return 0;
+}
+
+static int uniphier_i2c_tx(struct i2c_adapter *adap, u16 addr, u16 len,
+			   const u8 *buf)
+{
+	int ret;
+
+	dev_dbg(&adap->dev, "start condition\n");
+	ret = uniphier_i2c_send_byte(adap, addr << 1 |
+				     UNIPHIER_I2C_DTRM_STA |
+				     UNIPHIER_I2C_DTRM_NACK);
+	if (ret)
+		return ret;
+
+	while (len--) {
+		ret = uniphier_i2c_send_byte(adap,
+					     UNIPHIER_I2C_DTRM_NACK | *buf++);
+		if (ret)
+			return ret;
+	}
+
+	return 0;
+}
+
+static int uniphier_i2c_rx(struct i2c_adapter *adap, u16 addr, u16 len,
+			   u8 *buf)
+{
+	int ret;
+
+	dev_dbg(&adap->dev, "start condition\n");
+	ret = uniphier_i2c_send_byte(adap, addr << 1 |
+				     UNIPHIER_I2C_DTRM_STA |
+				     UNIPHIER_I2C_DTRM_NACK |
+				     UNIPHIER_I2C_DTRM_RD);
+	if (ret)
+		return ret;
+
+	while (len--) {
+		u32 rxdata;
+
+		ret = uniphier_i2c_xfer_byte(adap,
+					     len ? 0 : UNIPHIER_I2C_DTRM_NACK,
+					     &rxdata);
+		if (ret)
+			return ret;
+		*buf++ = rxdata;
+	}
+
+	return 0;
+}
+
+static int uniphier_i2c_stop(struct i2c_adapter *adap)
+{
+	dev_dbg(&adap->dev, "stop condition\n");
+	return uniphier_i2c_send_byte(adap, UNIPHIER_I2C_DTRM_STO |
+				      UNIPHIER_I2C_DTRM_NACK);
+}
+
+static int uniphier_i2c_master_xfer_one(struct i2c_adapter *adap,
+					struct i2c_msg *msg, bool stop)
+{
+	bool is_read = msg->flags & I2C_M_RD;
+	bool recovery = false;
+	int ret;
+
+	dev_dbg(&adap->dev, "%s: addr=0x%02x, len=%d, stop=%d\n",
+		is_read ? "receive" : "transmit", msg->addr, msg->len, stop);
+
+	if (is_read)
+		ret = uniphier_i2c_rx(adap, msg->addr, msg->len, msg->buf);
+	else
+		ret = uniphier_i2c_tx(adap, msg->addr, msg->len, msg->buf);
+
+	if (ret == -EAGAIN) /* could not acquire bus. bail out without STOP */
+		return ret;
+
+	if (ret == -ETIMEDOUT) {
+		/* This error is fatal.  Needs recovery. */
+		stop = false;
+		recovery = true;
+	}
+
+	if (stop) {
+		int ret2 = uniphier_i2c_stop(adap);
+
+		if (ret2) {
+			/* Failed to issue STOP.  The bus needs recovery. */
+			recovery = true;
+			ret = ret ?: ret2;
+		}
+	}
+
+	if (recovery)
+		i2c_recover_bus(adap);
+
+	return ret;
+}
+
+static int uniphier_i2c_check_bus_busy(struct i2c_adapter *adap)
+{
+	struct uniphier_i2c_priv *priv = i2c_get_adapdata(adap);
+
+	if (!(readl(priv->membase + UNIPHIER_I2C_DREC) &
+						UNIPHIER_I2C_DREC_BBN)) {
+		if (priv->busy_cnt++ > 3) {
+			/*
+			 * If bus busy continues too long, it is probably
+			 * in a wrong state.  Try bus recovery.
+			 */
+			i2c_recover_bus(adap);
+			priv->busy_cnt = 0;
+		}
+
+		return -EAGAIN;
+	}
+
+	priv->busy_cnt = 0;
+	return 0;
+}
+
+static int uniphier_i2c_master_xfer(struct i2c_adapter *adap,
+				    struct i2c_msg *msgs, int num)
+{
+	struct i2c_msg *msg, *emsg = msgs + num;
+	int ret;
+
+	ret = uniphier_i2c_check_bus_busy(adap);
+	if (ret)
+		return ret;
+
+	for (msg = msgs; msg < emsg; msg++) {
+		/* If next message is read, skip the stop condition */
+		bool stop = !(msg + 1 < emsg && msg[1].flags & I2C_M_RD);
+		/* but, force it if I2C_M_STOP is set */
+		if (msg->flags & I2C_M_STOP)
+			stop = true;
+
+		ret = uniphier_i2c_master_xfer_one(adap, msg, stop);
+		if (ret)
+			return ret;
+	}
+
+	return num;
+}
+
+static u32 uniphier_i2c_functionality(struct i2c_adapter *adap)
+{
+	return I2C_FUNC_I2C;
+}
+
+static const struct i2c_algorithm uniphier_i2c_algo = {
+	.master_xfer = uniphier_i2c_master_xfer,
+	.functionality = uniphier_i2c_functionality,
+};
+
+static void uniphier_i2c_reset(struct uniphier_i2c_priv *priv, bool reset_on)
+{
+	u32 val = UNIPHIER_I2C_BRST_RSCL;
+
+	val |= reset_on ? 0 : UNIPHIER_I2C_BRST_FOEN;
+	writel(val, priv->membase + UNIPHIER_I2C_BRST);
+}
+
+static int uniphier_i2c_get_scl(struct i2c_adapter *adap)
+{
+	struct uniphier_i2c_priv *priv = i2c_get_adapdata(adap);
+
+	return !!(readl(priv->membase + UNIPHIER_I2C_BSTS) &
+							UNIPHIER_I2C_BSTS_SCL);
+}
+
+static void uniphier_i2c_set_scl(struct i2c_adapter *adap, int val)
+{
+	struct uniphier_i2c_priv *priv = i2c_get_adapdata(adap);
+
+	writel(val ? UNIPHIER_I2C_BRST_RSCL : 0,
+	       priv->membase + UNIPHIER_I2C_BRST);
+}
+
+static int uniphier_i2c_get_sda(struct i2c_adapter *adap)
+{
+	struct uniphier_i2c_priv *priv = i2c_get_adapdata(adap);
+
+	return !!(readl(priv->membase + UNIPHIER_I2C_BSTS) &
+							UNIPHIER_I2C_BSTS_SDA);
+}
+
+static void uniphier_i2c_unprepare_recovery(struct i2c_adapter *adap)
+{
+	uniphier_i2c_reset(i2c_get_adapdata(adap), false);
+}
+
+static struct i2c_bus_recovery_info uniphier_i2c_bus_recovery_info = {
+	.recover_bus = i2c_generic_scl_recovery,
+	.get_scl = uniphier_i2c_get_scl,
+	.set_scl = uniphier_i2c_set_scl,
+	.get_sda = uniphier_i2c_get_sda,
+	.unprepare_recovery = uniphier_i2c_unprepare_recovery,
+};
+
+static int uniphier_i2c_clk_init(struct device *dev,
+				 struct uniphier_i2c_priv *priv)
+{
+	struct device_node *np = dev->of_node;
+	unsigned long clk_rate;
+	u32 bus_speed;
+	int ret;
+
+	if (of_property_read_u32(np, "clock-frequency", &bus_speed))
+		bus_speed = UNIPHIER_I2C_DEFAULT_SPEED;
+
+	if (bus_speed > UNIPHIER_I2C_MAX_SPEED)
+		bus_speed = UNIPHIER_I2C_MAX_SPEED;
+
+	/* Get input clk rate through clk driver */
+	priv->clk = devm_clk_get(dev, NULL);
+	if (IS_ERR(priv->clk)) {
+		dev_err(dev, "failed to get clock\n");
+		return PTR_ERR(priv->clk);
+	}
+
+	ret = clk_prepare_enable(priv->clk);
+	if (ret)
+		return ret;
+
+	clk_rate = clk_get_rate(priv->clk);
+
+	uniphier_i2c_reset(priv, true);
+
+	writel((clk_rate / bus_speed / 2 << 16) | (clk_rate / bus_speed),
+	       priv->membase + UNIPHIER_I2C_CLK);
+
+	uniphier_i2c_reset(priv, false);
+
+	return 0;
+}
+
+static int uniphier_i2c_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct uniphier_i2c_priv *priv;
+	struct resource *regs;
+	int irq;
+	int ret;
+
+	priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
+	if (!priv)
+		return -ENOMEM;
+
+	regs = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	if (!regs) {
+		dev_err(dev, "failed to get memory resource");
+		return -EINVAL;
+	}
+
+	priv->membase = devm_ioremap_resource(dev, regs);
+	if (IS_ERR(priv->membase))
+		return PTR_ERR(priv->membase);
+
+	irq = platform_get_irq(pdev, 0);
+	if (irq < 0) {
+		dev_err(dev, "failed to get IRQ number");
+		return irq;
+	}
+
+	init_completion(&priv->comp);
+	priv->adap.owner = THIS_MODULE;
+	priv->adap.algo = &uniphier_i2c_algo;
+	priv->adap.dev.parent = dev;
+	priv->adap.dev.of_node = dev->of_node;
+	strlcpy(priv->adap.name, "UniPhier I2C", sizeof(priv->adap.name));
+	priv->adap.bus_recovery_info = &uniphier_i2c_bus_recovery_info;
+	i2c_set_adapdata(&priv->adap, priv);
+	platform_set_drvdata(pdev, priv);
+
+	ret = uniphier_i2c_clk_init(dev, priv);
+	if (ret)
+		return ret;
+
+	ret = devm_request_irq(dev, irq, uniphier_i2c_interrupt, 0, pdev->name,
+			       priv);
+	if (ret) {
+		dev_err(dev, "failed to request irq %d\n", irq);
+		goto err;
+	}
+
+	ret = i2c_add_adapter(&priv->adap);
+	if (ret) {
+		dev_err(dev, "failed to add I2C adapter\n");
+		goto err;
+	}
+
+err:
+	if (ret)
+		clk_disable_unprepare(priv->clk);
+
+	return ret;
+}
+
+static int uniphier_i2c_remove(struct platform_device *pdev)
+{
+	struct uniphier_i2c_priv *priv = platform_get_drvdata(pdev);
+
+	i2c_del_adapter(&priv->adap);
+	clk_disable_unprepare(priv->clk);
+
+	return 0;
+}
+
+static const struct of_device_id uniphier_i2c_match[] = {
+	{ .compatible = "socionext,uniphier-i2c" },
+	{ /* sentinel */ }
+};
+MODULE_DEVICE_TABLE(of, uniphier_i2c_match);
+
+static struct platform_driver uniphier_i2c_drv = {
+	.probe  = uniphier_i2c_probe,
+	.remove = uniphier_i2c_remove,
+	.driver = {
+		.name  = "uniphier-i2c",
+		.of_match_table = uniphier_i2c_match,
+	},
+};
+module_platform_driver(uniphier_i2c_drv);
+
+MODULE_DESCRIPTION("UniPhier I2C bus driver");
+MODULE_AUTHOR("Masahiro Yamada <yamada.masahiro@socionext.com>");
+MODULE_LICENSE("GPL");
-- 
1.9.1

  reply	other threads:[~2015-07-30  8:14 UTC|newest]

Thread overview: 28+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2015-07-30  8:12 [PATCH 0/3] i2c: uniphier: add two I2C controller drivers for UniPhier SoC platform Masahiro Yamada
2015-07-30  8:12 ` Masahiro Yamada
2015-07-30  8:12 ` Masahiro Yamada
2015-07-30  8:12 ` Masahiro Yamada [this message]
2015-07-30  8:12   ` [PATCH 1/3] i2c: uniphier: add UniPhier FIFO-less I2C driver Masahiro Yamada
2015-07-30  8:12   ` Masahiro Yamada
2015-10-22 20:59   ` Wolfram Sang
2015-10-22 20:59     ` Wolfram Sang
2015-10-23 10:52     ` Masahiro Yamada
2015-10-23 10:52       ` Masahiro Yamada
2015-07-30  8:12 ` [PATCH 2/3] i2c: uniphier_f: add UniPhier FIFO-builtin " Masahiro Yamada
2015-07-30  8:12   ` Masahiro Yamada
2015-07-30  8:12   ` Masahiro Yamada
2015-10-22 21:06   ` Wolfram Sang
2015-10-22 21:06     ` Wolfram Sang
2015-10-23 10:59     ` Masahiro Yamada
2015-10-23 10:59       ` Masahiro Yamada
2015-07-30  8:12 ` [PATCH 3/3] i2c: uniphier: add bindings for UniPhier I2C controllers Masahiro Yamada
2015-07-30  8:12   ` Masahiro Yamada
2015-07-30  8:12   ` Masahiro Yamada
2015-10-22 21:00   ` Wolfram Sang
2015-10-22 21:00     ` Wolfram Sang
2015-10-23 10:54     ` Masahiro Yamada
2015-10-23 10:54       ` Masahiro Yamada
2015-10-23 10:54       ` Masahiro Yamada
2015-09-25  2:12 ` [PATCH 0/3] i2c: uniphier: add two I2C controller drivers for UniPhier SoC platform Masahiro Yamada
2015-09-25  2:12   ` Masahiro Yamada
2015-09-25  2:12   ` Masahiro Yamada

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=1438243942-26401-2-git-send-email-yamada.masahiro@socionext.com \
    --to=yamada.masahiro@socionext.com \
    --cc=Zubair.Kakakhel@imgtec.com \
    --cc=abrestic@chromium.org \
    --cc=anders.berg@avagotech.com \
    --cc=baruch@tkos.co.il \
    --cc=david.e.box@linux.intel.com \
    --cc=geert@linux-m68k.org \
    --cc=kdasu.kdev@gmail.com \
    --cc=laurentiu.palcu@intel.com \
    --cc=lee.jones@linaro.org \
    --cc=linux-arm-kernel@lists.infradead.org \
    --cc=linux-i2c@vger.kernel.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=max.schwarz@online.de \
    --cc=mika.westerberg@linux.intel.com \
    --cc=neelegup@linux.vnet.ibm.com \
    --cc=rjui@broadcom.com \
    --cc=sachin.kamat@samsung.com \
    --cc=sledge.yanwei@huawei.com \
    --cc=wsa@the-dreams.de \
    --cc=xudong.chen@mediatek.com \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.