From: Ryan Hsu <ryanhsu@qca.qualcomm.com> To: <ath10k@lists.infradead.org> Cc: <linux-wireless@vger.kernel.org>, <ryanhsu@qca.qualcomm.com> Subject: [PATCH v3] ath10k: Override CE5 configuration for QCA6147 device Date: Wed, 11 Nov 2015 10:21:22 -0800 [thread overview] Message-ID: <1447266082-10933-1-git-send-email-ryanhsu@qca.qualcomm.com> (raw) 'Commit a70587b3389a ("ath10k: configure copy engine 5 for HTT messages")' Introduces to use the unused CE5 for target to host message. For the device like QCA6174, CE5 already assigned for other feature. So for QCA6174, override the CE5 configuration and use the CE1 instead. This patch is based on Rajkumar's earlier patch. Fixes: a70587b3389a ("ath10k: configure copy engine 5 for HTT messages") Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com> Signed-off-by: Ryan Hsu <ryanhsu@qca.qualcomm.com> --- drivers/net/wireless/ath/ath10k/pci.c | 32 +++++++++++++++++++++++++++++--- 1 file changed, 29 insertions(+), 3 deletions(-) diff --git a/drivers/net/wireless/ath/ath10k/pci.c b/drivers/net/wireless/ath/ath10k/pci.c index 5c91a67..2a48376 100644 --- a/drivers/net/wireless/ath/ath10k/pci.c +++ b/drivers/net/wireless/ath/ath10k/pci.c @@ -113,7 +113,7 @@ static void ath10k_pci_htt_tx_cb(struct ath10k_ce_pipe *ce_state); static void ath10k_pci_htt_rx_cb(struct ath10k_ce_pipe *ce_state); static void ath10k_pci_pktlog_rx_cb(struct ath10k_ce_pipe *ce_state); -static const struct ce_attr host_ce_config_wlan[] = { +static struct ce_attr host_ce_config_wlan[] = { /* CE0: host->target HTC control and raw streams */ { .flags = CE_ATTR_FLAGS, @@ -219,7 +219,7 @@ static const struct ce_attr host_ce_config_wlan[] = { }; /* Target firmware's Copy Engine configuration. */ -static const struct ce_pipe_config target_ce_config_wlan[] = { +static struct ce_pipe_config target_ce_config_wlan[] = { /* CE0: host->target HTC control and raw streams */ { .pipenum = __cpu_to_le32(0), @@ -332,7 +332,7 @@ static const struct ce_pipe_config target_ce_config_wlan[] = { * This table is derived from the CE_PCI TABLE, above. * It is passed to the Target at startup for use by firmware. */ -static const struct service_to_pipe target_service_to_ce_map_wlan[] = { +static struct service_to_pipe target_service_to_ce_map_wlan[] = { { __cpu_to_le32(ATH10K_HTC_SVC_ID_WMI_DATA_VO), __cpu_to_le32(PIPEDIR_OUT), /* out = UL = host -> target */ @@ -2038,6 +2038,29 @@ static int ath10k_pci_init_config(struct ath10k *ar) return 0; } +static void ath10k_pci_override_ce_config(struct ath10k *ar) +{ + struct ce_attr *attr; + struct ce_pipe_config *config; + + /* For QCA6174 we're overriding the Copy Engine 5 configuration, + * since it is currently used for other feature. + */ + + /* Override Host's Copy Engine 5 configuration */ + attr = &host_ce_config_wlan[5]; + attr->src_sz_max = 0; + attr->dest_nentries = 0; + + /* Override Target firmware's Copy Engine configuration */ + config = &target_ce_config_wlan[5]; + config->pipedir = __cpu_to_le32(PIPEDIR_OUT); + config->nbytes_max = __cpu_to_le32(2048); + + /* Map from service/endpoint to Copy Engine */ + target_service_to_ce_map_wlan[15].pipenum = __cpu_to_le32(1); +} + static int ath10k_pci_alloc_pipes(struct ath10k *ar) { struct ath10k_pci *ar_pci = ath10k_pci_priv(ar); @@ -3031,6 +3054,9 @@ static int ath10k_pci_probe(struct pci_dev *pdev, goto err_core_destroy; } + if (QCA_REV_6174(ar)) + ath10k_pci_override_ce_config(ar); + ret = ath10k_pci_alloc_pipes(ar); if (ret) { ath10k_err(ar, "failed to allocate copy engine pipes: %d\n", -- 1.9.1
WARNING: multiple messages have this Message-ID (diff)
From: Ryan Hsu <ryanhsu@qca.qualcomm.com> To: ath10k@lists.infradead.org Cc: linux-wireless@vger.kernel.org, ryanhsu@qca.qualcomm.com Subject: [PATCH v3] ath10k: Override CE5 configuration for QCA6147 device Date: Wed, 11 Nov 2015 10:21:22 -0800 [thread overview] Message-ID: <1447266082-10933-1-git-send-email-ryanhsu@qca.qualcomm.com> (raw) 'Commit a70587b3389a ("ath10k: configure copy engine 5 for HTT messages")' Introduces to use the unused CE5 for target to host message. For the device like QCA6174, CE5 already assigned for other feature. So for QCA6174, override the CE5 configuration and use the CE1 instead. This patch is based on Rajkumar's earlier patch. Fixes: a70587b3389a ("ath10k: configure copy engine 5 for HTT messages") Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com> Signed-off-by: Ryan Hsu <ryanhsu@qca.qualcomm.com> --- drivers/net/wireless/ath/ath10k/pci.c | 32 +++++++++++++++++++++++++++++--- 1 file changed, 29 insertions(+), 3 deletions(-) diff --git a/drivers/net/wireless/ath/ath10k/pci.c b/drivers/net/wireless/ath/ath10k/pci.c index 5c91a67..2a48376 100644 --- a/drivers/net/wireless/ath/ath10k/pci.c +++ b/drivers/net/wireless/ath/ath10k/pci.c @@ -113,7 +113,7 @@ static void ath10k_pci_htt_tx_cb(struct ath10k_ce_pipe *ce_state); static void ath10k_pci_htt_rx_cb(struct ath10k_ce_pipe *ce_state); static void ath10k_pci_pktlog_rx_cb(struct ath10k_ce_pipe *ce_state); -static const struct ce_attr host_ce_config_wlan[] = { +static struct ce_attr host_ce_config_wlan[] = { /* CE0: host->target HTC control and raw streams */ { .flags = CE_ATTR_FLAGS, @@ -219,7 +219,7 @@ static const struct ce_attr host_ce_config_wlan[] = { }; /* Target firmware's Copy Engine configuration. */ -static const struct ce_pipe_config target_ce_config_wlan[] = { +static struct ce_pipe_config target_ce_config_wlan[] = { /* CE0: host->target HTC control and raw streams */ { .pipenum = __cpu_to_le32(0), @@ -332,7 +332,7 @@ static const struct ce_pipe_config target_ce_config_wlan[] = { * This table is derived from the CE_PCI TABLE, above. * It is passed to the Target at startup for use by firmware. */ -static const struct service_to_pipe target_service_to_ce_map_wlan[] = { +static struct service_to_pipe target_service_to_ce_map_wlan[] = { { __cpu_to_le32(ATH10K_HTC_SVC_ID_WMI_DATA_VO), __cpu_to_le32(PIPEDIR_OUT), /* out = UL = host -> target */ @@ -2038,6 +2038,29 @@ static int ath10k_pci_init_config(struct ath10k *ar) return 0; } +static void ath10k_pci_override_ce_config(struct ath10k *ar) +{ + struct ce_attr *attr; + struct ce_pipe_config *config; + + /* For QCA6174 we're overriding the Copy Engine 5 configuration, + * since it is currently used for other feature. + */ + + /* Override Host's Copy Engine 5 configuration */ + attr = &host_ce_config_wlan[5]; + attr->src_sz_max = 0; + attr->dest_nentries = 0; + + /* Override Target firmware's Copy Engine configuration */ + config = &target_ce_config_wlan[5]; + config->pipedir = __cpu_to_le32(PIPEDIR_OUT); + config->nbytes_max = __cpu_to_le32(2048); + + /* Map from service/endpoint to Copy Engine */ + target_service_to_ce_map_wlan[15].pipenum = __cpu_to_le32(1); +} + static int ath10k_pci_alloc_pipes(struct ath10k *ar) { struct ath10k_pci *ar_pci = ath10k_pci_priv(ar); @@ -3031,6 +3054,9 @@ static int ath10k_pci_probe(struct pci_dev *pdev, goto err_core_destroy; } + if (QCA_REV_6174(ar)) + ath10k_pci_override_ce_config(ar); + ret = ath10k_pci_alloc_pipes(ar); if (ret) { ath10k_err(ar, "failed to allocate copy engine pipes: %d\n", -- 1.9.1 _______________________________________________ ath10k mailing list ath10k@lists.infradead.org http://lists.infradead.org/mailman/listinfo/ath10k
next reply other threads:[~2015-11-11 18:21 UTC|newest] Thread overview: 10+ messages / expand[flat|nested] mbox.gz Atom feed top 2015-11-11 18:21 Ryan Hsu [this message] 2015-11-11 18:21 ` [PATCH v3] ath10k: Override CE5 configuration for QCA6147 device Ryan Hsu 2015-11-12 10:47 ` Julian Calaby 2015-11-12 10:47 ` Julian Calaby 2015-11-12 14:53 ` Kalle Valo 2015-11-12 14:53 ` Kalle Valo -- strict thread matches above, loose matches on Subject: below -- 2015-11-06 2:44 Ryan Hsu 2015-11-06 2:44 ` Ryan Hsu 2015-11-12 19:07 ` Kalle Valo 2015-11-12 19:07 ` Kalle Valo
Reply instructions: You may reply publicly to this message via plain-text email using any one of the following methods: * Save the following mbox file, import it into your mail client, and reply-to-all from there: mbox Avoid top-posting and favor interleaved quoting: https://en.wikipedia.org/wiki/Posting_style#Interleaved_style * Reply using the --to, --cc, and --in-reply-to switches of git-send-email(1): git send-email \ --in-reply-to=1447266082-10933-1-git-send-email-ryanhsu@qca.qualcomm.com \ --to=ryanhsu@qca.qualcomm.com \ --cc=ath10k@lists.infradead.org \ --cc=linux-wireless@vger.kernel.org \ /path/to/YOUR_REPLY https://kernel.org/pub/software/scm/git/docs/git-send-email.html * If your mail client supports setting the In-Reply-To header via mailto: links, try the mailto: linkBe sure your reply has a Subject: header at the top and a blank line before the message body.
This is an external index of several public inboxes, see mirroring instructions on how to clone and mirror all data and code used by this external index.