[RFC PATCH 5/9] drm/rockchip: Optimization vop mode set

[Mark Yao <mark.yao@rock-chips.com>]

Rk3288 vop timing registers is immediately register, when configure
timing on display active time, will cause tearing. use dclk reset is
not a good idea to avoid this tearing. we can avoid tearing by using
standby register.

Vop standby register will take effect at end of current frame, and
go back to work immediately when exit standby.

So we can use standby register to protect this context.

Signed-off-by: Mark Yao <mark.yao@rock-chips.com>
---
 drivers/gpu/drm/rockchip/rockchip_drm_vop.c |   49 +++++++++++++++++++--------
 1 file changed, 34 insertions(+), 15 deletions(-)

diff --git a/drivers/gpu/drm/rockchip/rockchip_drm_vop.c b/drivers/gpu/drm/rockchip/rockchip_drm_vop.c
index a28e255..6317dea 100644
--- a/drivers/gpu/drm/rockchip/rockchip_drm_vop.c
+++ b/drivers/gpu/drm/rockchip/rockchip_drm_vop.c
@@ -1098,10 +1098,40 @@ static void vop_crtc_mode_set_nofb(struct drm_crtc *crtc)
 	uint32_t val;
 
 	/*
-	 * disable dclk to stop frame scan, so that we can safe config mode and
-	 * enable iommu.
+	 * If dclk rate is zero, mean that scanout is stop,
+	 * we don't need wait any more.
 	 */
-	clk_disable(vop->dclk);
+	if (clk_get_rate(vop->dclk)) {
+		/*
+		 * Rk3288 vop timing register is immediately, when configure
+		 * display timing on display time, may cause tearing.
+		 *
+		 * Vop standby will take effect at end of current frame,
+		 * if dsp hold valid irq happen, it means standby complete.
+		 *
+		 * mode set:
+		 *    standby and wait complete --> |----
+		 *                                  | display time
+		 *                                  |----
+		 *                                  |---> dsp hold irq
+		 *     configure display timing --> |
+		 *         standby exit             |
+		 *                                  | new frame start.
+		 */
+
+		reinit_completion(&vop->dsp_hold_completion);
+		vop_dsp_hold_valid_irq_enable(vop);
+
+		spin_lock(&vop->reg_lock);
+
+		VOP_CTRL_SET(vop, standby, 1);
+
+		spin_unlock(&vop->reg_lock);
+
+		wait_for_completion(&vop->dsp_hold_completion);
+
+		vop_dsp_hold_valid_irq_disable(vop);
+	}
 
 	switch (vop->connector_type) {
 	case DRM_MODE_CONNECTOR_LVDS:
@@ -1137,20 +1167,9 @@ static void vop_crtc_mode_set_nofb(struct drm_crtc *crtc)
 	VOP_CTRL_SET(vop, vact_st_end, val);
 	VOP_CTRL_SET(vop, vpost_st_end, val);
 
-
-	/*
-	 * reset dclk, take all mode config affect, so the clk would run in
-	 * correct frame.
-	 */
-	reset_control_assert(vop->dclk_rst);
-	usleep_range(10, 20);
-	reset_control_deassert(vop->dclk_rst);
-
 	clk_set_rate(vop->dclk, adjusted_mode->clock * 1000);
-out:
-	if (clk_enable(vop->dclk) < 0)
-		dev_err(vop->dev, "failed to enable dclk - %d\n", ret_clk);
 
+	VOP_CTRL_SET(vop, standby, 0);
 }
 
 static void vop_crtc_atomic_flush(struct drm_crtc *crtc,
-- 
1.7.9.5