[PATCH v3] clk: ti: Add support for dm814x ADPLL

[Tony Lindgren <tony@atomide.com>]

On dm814x we have 13 ADPLLs with 3 to 4 outputs on each. The
ADPLLs have several dividers and muxes controlled by a shared
control register for each PLL.

Note that for the clocks to work as device drivers for booting on
dm814x, this patch depends on "ARM: OMAP2+: Change core_initcall
levels to postcore_initcall".

Also note that this patch does not implement clk_set_rate for the
PLL, that will be posted later on when available.

Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
---
Changes from v2 to v3 are listed below, hopefully I addressed everybody's
comments,please check and let me know if I missed something.

After review, it is suggested that Tero applies this patch into an
immutable branch against v4.4-rc1 that then gets submitted as a pull
request along with other omap clock patches to Mike and Stephen. That
way I can merge the clock driver too into my omap-for-v4.5/soc branch.

Changes since v2:

Addressed comments from RMK:

- Use clkdev_create() and set up separate con id from name in format
  "pll260dcoclkldo" to avoid the MAX_CON_ID limitations

Addressed comments from Tero:

- Change register access to use offsets from d->regs instead of setting
  up separate void __iomem * registers

- Change ti_adpll_clkout_set_parent() to return -EAGAIN if unavailable
  parent is selected

Addressed comments from Matthijs:

- Standardize on "dcoclkldo" output name and use that name also for TRM
  "clkdcoldo"

- Use "bypass" name instead of "ulow" used in TRM 

- Use 16-bit register access in ti_adpll_recalc_rate() to simplify
  the code

- Use ti_adpll_set_idle_bypass() naming to make it clear it's the idle
  mode

- Check PLL lock for both ti_adpll_is_prepared() and ti_adpll_wait_lock()

---
 .../devicetree/bindings/clock/ti/adpll.txt         |   43 +
 drivers/clk/Kconfig                                |    1 +
 drivers/clk/ti/Kconfig                             |    6 +
 drivers/clk/ti/Makefile                            |    2 +
 drivers/clk/ti/adpll.c                             | 1003 ++++++++++++++++++++
 drivers/clk/ti/clk-814x.c                          |   53 ++
 6 files changed, 1108 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/clock/ti/adpll.txt
 create mode 100644 drivers/clk/ti/Kconfig
 create mode 100644 drivers/clk/ti/adpll.c

diff --git a/Documentation/devicetree/bindings/clock/ti/adpll.txt b/Documentation/devicetree/bindings/clock/ti/adpll.txt
new file mode 100644
index 0000000..3c41aea
--- /dev/null
+++ b/Documentation/devicetree/bindings/clock/ti/adpll.txt
@@ -0,0 +1,43 @@
+Binding for Texas Instruments ADPLL clock.
+
+Binding status: Unstable - ABI compatibility may be broken in the future
+
+This binding uses the common clock binding[1]. It assumes a
+register-mapped ADPLL with two to three selectable input clocks
+and three to four children..
+
+[1] Documentation/devicetree/bindings/clock/clock-bindings.txt
+
+Required properties:
+- compatible : shall be one of "ti,dm814-adpll-s-clock" or
+  "ti,dm814-adpll-lj-clock" depending on the type of the ADPLL
+- #clock-cells : from common clock binding; shall be set to 0.
+- clocks : link phandles of parent clocks clkinp and clkinpulow, note
+  that the adpll-s-clock also has an optional clkinphif
+- reg : address and length of the register set for controlling the ADPLL.
+
+Examples:
+	adpll_mpu_ck: adpll@40 {
+		#clock-cells = <1>;
+		compatible = "ti,dm814-adpll-s-clock";
+		reg = <0x40 0x40>;
+		clocks = <&devosc_ck &devosc_ck &devosc_ck>;
+		clock-names = "clkinp", "clkinpulow", "clkinphif";
+		clock-indices = <0>, <1>, <2>, <3>;
+		clock-output-names = "481c5040.adpll.dcoclkldo",
+				     "481c5040.adpll.clkout",
+				     "481c5040.adpll.clkoutx2",
+				     "481c5040.adpll.clkouthif";
+	};
+
+	adpll_dsp_ck: adpll@80 {
+		#clock-cells = <1>;
+		compatible = "ti,dm814-adpll-lj-clock";
+		reg = <0x80 0x30>;
+		clocks = <&devosc_ck &devosc_ck>;
+		clock-names = "clkinp", "clkinpulow";
+		clock-indices = <0>, <1>, <2>;
+		clock-output-names = "481c5080.adpll.dcoclkldo",
+				     "481c5080.adpll.clkout",
+				     "481c5080.adpll.clkoutldo";
+	};
diff --git a/drivers/clk/Kconfig b/drivers/clk/Kconfig
index c3e3a02f..c0c9868 100644
--- a/drivers/clk/Kconfig
+++ b/drivers/clk/Kconfig
@@ -190,6 +190,7 @@ config COMMON_CLK_CDCE706
 
 source "drivers/clk/bcm/Kconfig"
 source "drivers/clk/hisilicon/Kconfig"
+source "drivers/clk/ti/Kconfig"
 source "drivers/clk/qcom/Kconfig"
 
 endmenu
diff --git a/drivers/clk/ti/Kconfig b/drivers/clk/ti/Kconfig
new file mode 100644
index 0000000..a9d5474
--- /dev/null
+++ b/drivers/clk/ti/Kconfig
@@ -0,0 +1,6 @@
+config COMMON_CLK_TI_ADPLL
+	tristate "Clock driver for dm814x ADPLL"
+	depends on ARCH_OMAP2PLUS
+	default y if SOC_TI81XX
+	---help---
+	  ADPLL clock driver for the dm814x SoC using common clock framework.
diff --git a/drivers/clk/ti/Makefile b/drivers/clk/ti/Makefile
index d4ac960..dfe91d7 100644
--- a/drivers/clk/ti/Makefile
+++ b/drivers/clk/ti/Makefile
@@ -18,3 +18,5 @@ obj-$(CONFIG_SOC_AM43XX)		+= $(clk-common) dpll3xxx.o clk-43xx.o
 ifdef CONFIG_ATAGS
 obj-$(CONFIG_ARCH_OMAP3)                += clk-3xxx-legacy.o
 endif
+
+obj-$(CONFIG_COMMON_CLK_TI_ADPLL)	+= adpll.o
diff --git a/drivers/clk/ti/adpll.c b/drivers/clk/ti/adpll.c
new file mode 100644
index 0000000..571ae8c
--- /dev/null
+++ b/drivers/clk/ti/adpll.c
@@ -0,0 +1,1003 @@
+/*
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation version 2.
+ *
+ * This program is distributed "as is" WITHOUT ANY WARRANTY of any
+ * kind, whether express or implied; without even the implied warranty
+ * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#include <linux/clk.h>
+#include <linux/clkdev.h>
+#include <linux/clk-provider.h>
+#include <linux/delay.h>
+#include <linux/err.h>
+#include <linux/math64.h>
+#include <linux/module.h>
+#include <linux/of_device.h>
+#include <linux/string.h>
+
+#define ADPLL_PLLSS_MMR_LOCK_OFFSET	0x00	/* Managed by MPPULL */
+#define ADPLL_PLLSS_MMR_LOCK_ENABLED	0x1f125B64
+#define ADPLL_PLLSS_MMR_UNLOCK_MAGIC	0x1eda4c3d
+
+#define ADPLL_PWRCTRL_OFFSET		0x00
+#define ADPLL_PWRCTRL_PONIN		5
+#define ADPLL_PWRCTRL_PGOODIN		4
+#define ADPLL_PWRCTRL_RET		3
+#define ADPLL_PWRCTRL_ISORET		2
+#define ADPLL_PWRCTRL_ISOSCAN		1
+#define ADPLL_PWRCTRL_OFFMODE		0
+
+#define ADPLL_CLKCTRL_OFFSET		0x04
+#define ADPLL_CLKCTRL_CLKDCOLDOEN	29
+#define ADPLL_CLKCTRL_IDLE		23
+#define ADPLL_CLKCTRL_CLKOUTEN		20
+#define ADPLL_CLKINPHIFSEL_ADPLL_S	19	/* REVISIT: which bit? */
+#define ADPLL_CLKCTRL_CLKOUTLDOEN_ADPLL_LJ 19
+#define ADPLL_CLKCTRL_ULOWCLKEN		18
+#define ADPLL_CLKCTRL_CLKDCOLDOPWDNZ	17
+#define ADPLL_CLKCTRL_M2PWDNZ		16
+#define ADPLL_CLKCTRL_M3PWDNZ_ADPLL_S	15
+#define ADPLL_CLKCTRL_LOWCURRSTDBY_ADPLL_S 13
+#define ADPLL_CLKCTRL_LPMODE_ADPLL_S	12
+#define ADPLL_CLKCTRL_REGM4XEN_ADPLL_S	10
+#define ADPLL_CLKCTRL_SELFREQDCO_ADPLL_LJ 10
+#define ADPLL_CLKCTRL_TINITZ		0
+
+#define ADPLL_TENABLE_OFFSET		0x08
+#define ADPLL_TENABLE_TENABLE		0
+
+#define ADPLL_TENABLEDIV_OFFSET		0x8c
+#define ADPLL_TENABLEDIV_TENABLEDIV	0
+
+#define ADPLL_M2NDIV_OFFSET		0x10
+#define ADPLL_M2NDIV_M2			16
+#define ADPLL_M2NDIV_M2_ADPLL_S_WIDTH	5
+#define ADPLL_M2NDIV_M2_ADPLL_LJ_WIDTH	7
+#define ADPLL_M2NDIV_N			0
+#define ADPLL_M2NDIV_N_ADPLL_S_MASK	0x7f
+#define ADPLL_M2NDIV_N_ADPLL_LJ_MASK	0xff
+
+#define ADPLL_MN2DIV_OFFSET		0x14
+#define ADPLL_MN2DIV_N2			16
+#define ADPLL_MN2DIV_M			0
+#define ADPLL_MN2DIV_M_MASK		0xfff
+
+#define ADPLL_FRACDIV_OFFSET		0x18
+#define ADPLL_FRACDIV_REGSD		24
+#define ADPLL_FRACDIV_FRACTIONALM	0
+#define ADPLL_FRACDIV_FRACTIONALM_MASK	0x3ffff
+
+#define ADPLL_BWCTRL_OFFSET		0x1c
+#define ADPLL_BWCTRL_BWCONTROL		1
+#define ADPLL_BWCTRL_BW_INCR_DECRZ	0
+
+#define ADPLL_RESERVED_OFFSET		0x20
+
+#define ADPLL_STATUS_OFFSET		0x24
+#define ADPLL_STATUS_PONOUT		31
+#define ADPLL_STATUS_PGOODOUT		30
+#define ADPLL_STATUS_LDOPWDN		29
+#define ADPLL_STATUS_RECAL_BSTATUS3	28
+#define ADPLL_STATUS_RECAL_OPPIN	27
+#define ADPLL_STATUS_PHASELOCK		10
+#define ADPLL_STATUS_FREQLOCK		9
+#define ADPLL_STATUS_BYPASSACK		8
+#define ADPLL_STATUS_LOSSREF		6
+#define ADPLL_STATUS_CLKOUTENACK	5
+#define ADPLL_STATUS_LOCK2		4
+#define ADPLL_STATUS_M2CHANGEACK	3
+#define ADPLL_STATUS_HIGHJITTER		1
+#define ADPLL_STATUS_BYPASS		0
+#define ADPLL_STATUS_PREPARED_MASK	(BIT(ADPLL_STATUS_PHASELOCK) | \
+					 BIT(ADPLL_STATUS_FREQLOCK))
+
+#define ADPLL_M3DIV_OFFSET		0x28	/* Only on MPUPLL */
+#define ADPLL_M3DIV_M3			0
+#define ADPLL_M3DIV_M3_WIDTH		5
+#define ADPLL_M3DIV_M3_MASK		0x1f
+
+#define ADPLL_RAMPCTRL_OFFSET		0x2c	/* Only on MPUPLL */
+#define ADPLL_RAMPCTRL_CLKRAMPLEVEL	19
+#define ADPLL_RAMPCTRL_CLKRAMPRATE	16
+#define ADPLL_RAMPCTRL_RELOCK_RAMP_EN	0
+
+#define MAX_ADPLL_INPUTS		3
+#define MAX_ADPLL_OUTPUTS		4
+#define ADPLL_MAX_RETRIES		5
+
+#define to_dco(_hw)	container_of(_hw, struct ti_adpll_dco_data, hw)
+#define to_adpll(_hw)	container_of(_hw, struct ti_adpll_data, dco)
+#define to_clkout(_hw)	container_of(_hw, struct ti_adpll_clkout_data, hw)
+
+enum ti_adpll_clocks {
+	TI_ADPLL_DCO,
+	TI_ADPLL_DCO_GATE,
+	TI_ADPLL_N2,
+	TI_ADPLL_M2,
+	TI_ADPLL_M2_GATE,
+	TI_ADPLL_BYPASS,
+	TI_ADPLL_HIF,
+	TI_ADPLL_DIV2,
+	TI_ADPLL_CLKOUT,
+	TI_ADPLL_CLKOUT2,
+	TI_ADPLL_M3,
+};
+
+#define TI_ADPLL_NR_CLOCKS	(TI_ADPLL_M3 + 1)
+
+enum ti_adpll_inputs {
+	TI_ADPLL_CLKINP,
+	TI_ADPLL_CLKINPULOW,
+	TI_ADPLL_CLKINPHIF,
+};
+
+enum ti_adpll_s_outputs {
+	TI_ADPLL_S_DCOCLKLDO,
+	TI_ADPLL_S_CLKOUT,
+	TI_ADPLL_S_CLKOUTX2,
+	TI_ADPLL_S_CLKOUTHIF,
+};
+
+enum ti_adpll_lj_outputs {
+	TI_ADPLL_LJ_CLKDCOLDO,
+	TI_ADPLL_LJ_CLKOUT,
+	TI_ADPLL_LJ_CLKOUTLDO,
+};
+
+struct ti_adpll_platform_data {
+	const bool is_type_s;
+	const int nr_max_inputs;
+	const int nr_max_outputs;
+	const int output_index;
+};
+
+struct ti_adpll_clock {
+	struct clk *clk;
+	struct clk_lookup *cl;
+	void (*unregister)(struct clk *clk);
+};
+
+struct ti_adpll_dco_data {
+	struct clk_hw hw;
+};
+
+struct ti_adpll_clkout_data {
+	struct ti_adpll_data *adpll;
+	struct clk_gate gate;
+	struct clk_hw hw;
+};
+
+struct ti_adpll_data {
+	struct device *dev;
+	const struct ti_adpll_platform_data *c;
+	struct device_node *np;
+	unsigned long pa;
+	void __iomem *iobase;
+	void __iomem *regs;
+	spinlock_t lock;	/* For ADPLL shared register access */
+	const char *parent_names[MAX_ADPLL_INPUTS];
+	struct clk *parent_clocks[MAX_ADPLL_INPUTS];
+	struct ti_adpll_clock *clocks;
+	struct clk_onecell_data outputs;
+	struct ti_adpll_dco_data dco;
+};
+
+static const char *ti_adpll_clk_get_name(struct ti_adpll_data *d,
+					 int output_index,
+					 const char *postfix)
+{
+	const char *name;
+	int err;
+
+	if (output_index >= 0) {
+		err = of_property_read_string_index(d->np,
+						    "clock-output-names",
+						    output_index,
+						    &name);
+		if (err)
+			return NULL;
+	} else {
+		const char *base_name = "adpll";
+		char *buf;
+
+		buf = devm_kzalloc(d->dev, 8 + 1 + strlen(base_name) + 1 +
+				    strlen(postfix), GFP_KERNEL);
+		if (!buf)
+			return NULL;
+		sprintf(buf, "%08lx.%s.%s", d->pa, base_name, postfix);
+		name = buf;
+	}
+
+	return name;
+}
+
+#define ADPLL_MAX_CON_ID	16	/* See MAX_CON_ID */
+
+static int ti_adpll_setup_clock(struct ti_adpll_data *d, struct clk *clock,
+				int index, int output_index, const char *name,
+				void (*unregister)(struct clk *clk))
+{
+	struct clk_lookup *cl;
+	const char *postfix = NULL;
+	char con_id[ADPLL_MAX_CON_ID];
+
+	d->clocks[index].clk = clock;
+	d->clocks[index].unregister = unregister;
+
+	if (output_index < 0)
+		return 0;
+
+	/* Separate con_id in format "pll040dcoclkldo" to fit MAX_CON_ID */
+	postfix = strrchr(name, '.');
+	if (strlen(postfix) > 1) {
+		if (strlen(postfix) > ADPLL_MAX_CON_ID)
+			dev_warn(d->dev, "clock %s con_id lookup may fail\n",
+				 name);
+		snprintf(con_id, 16, "pll%03lx%s", d->pa & 0xfff, postfix + 1);
+		cl = clkdev_create(clock, con_id, NULL);
+		if (!cl)
+			return -ENOMEM;
+		d->clocks[index].cl = cl;
+	} else {
+		dev_warn(d->dev, "no con_id for clock %s\n", name);
+	}
+
+	d->outputs.clks[output_index] = clock;
+	d->outputs.clk_num++;
+
+	return 0;
+}
+
+static int ti_adpll_init_divider(struct ti_adpll_data *d,
+				 enum ti_adpll_clocks index,
+				 int output_index, char *name,
+				 struct clk *parent_clock,
+				 void __iomem *reg,
+				 u8 shift, u8 width,
+				 u8 clk_divider_flags)
+{
+	const char *child_name;
+	const char *parent_name;
+	struct clk *clock;
+
+	child_name = ti_adpll_clk_get_name(d, output_index, name);
+	if (!child_name)
+		return -EINVAL;
+
+	parent_name = __clk_get_name(parent_clock);
+	clock = clk_register_divider(d->dev, child_name, parent_name, 0,
+				     reg, shift, width, clk_divider_flags,
+				     &d->lock);
+	if (IS_ERR(clock)) {
+		dev_err(d->dev, "failed to register divider %s: %li\n",
+			name, PTR_ERR(clock));
+		return PTR_ERR(clock);
+	}
+
+	return ti_adpll_setup_clock(d, clock, index, output_index, child_name,
+				    clk_unregister_divider);
+}
+
+static int ti_adpll_init_mux(struct ti_adpll_data *d,
+			     enum ti_adpll_clocks index,
+			     char *name, struct clk *clk0,
+			     struct clk *clk1,
+			     void __iomem *reg,
+			     u8 shift)
+{
+	const char *child_name;
+	const char *parents[2];
+	struct clk *clock;
+
+	child_name = ti_adpll_clk_get_name(d, -ENODEV, name);
+	if (!child_name)
+		return -ENOMEM;
+	parents[0] = __clk_get_name(clk0);
+	parents[1] = __clk_get_name(clk1);
+	clock = clk_register_mux(d->dev, child_name, parents, 2, 0,
+				 reg, shift, 1, 0, &d->lock);
+	if (IS_ERR(clock)) {
+		dev_err(d->dev, "failed to register mux %s: %li\n",
+			name, PTR_ERR(clock));
+		return PTR_ERR(clock);
+	}
+
+	return ti_adpll_setup_clock(d, clock, index, -ENODEV, child_name,
+				    clk_unregister_mux);
+}
+
+static int ti_adpll_init_gate(struct ti_adpll_data *d,
+			      enum ti_adpll_clocks index,
+			      int output_index, char *name,
+			      struct clk *parent_clock,
+			      void __iomem *reg,
+			      u8 bit_idx,
+			      u8 clk_gate_flags)
+{
+	const char *child_name;
+	const char *parent_name;
+	struct clk *clock;
+
+	child_name = ti_adpll_clk_get_name(d, output_index, name);
+	if (!child_name)
+		return -EINVAL;
+
+	parent_name = __clk_get_name(parent_clock);
+	clock = clk_register_gate(d->dev, child_name, parent_name, 0,
+				  reg, bit_idx, clk_gate_flags,
+				  &d->lock);
+	if (IS_ERR(clock)) {
+		dev_err(d->dev, "failed to register gate %s: %li\n",
+			name, PTR_ERR(clock));
+		return PTR_ERR(clock);
+	}
+
+	return ti_adpll_setup_clock(d, clock, index, output_index, child_name,
+				    clk_unregister_gate);
+}
+
+static int ti_adpll_init_fixed_factor(struct ti_adpll_data *d,
+				      enum ti_adpll_clocks index,
+				      char *name,
+				      struct clk *parent_clock,
+				      unsigned int mult,
+				      unsigned int div)
+{
+	const char *child_name;
+	const char *parent_name;
+	struct clk *clock;
+
+	child_name = ti_adpll_clk_get_name(d, -ENODEV, name);
+	if (!child_name)
+		return -ENOMEM;
+
+	parent_name = __clk_get_name(parent_clock);
+	clock = clk_register_fixed_factor(d->dev, child_name, parent_name,
+					  0, mult, div);
+	if (IS_ERR(clock))
+		return PTR_ERR(clock);
+
+	return ti_adpll_setup_clock(d, clock, index, -ENODEV, child_name,
+				    clk_unregister);
+}
+
+static void ti_adpll_set_idle_bypass(struct ti_adpll_data *d)
+{
+	unsigned long flags;
+	u32 v;
+
+	spin_lock_irqsave(&d->lock, flags);
+	v = readl_relaxed(d->regs + ADPLL_CLKCTRL_OFFSET);
+	v |= BIT(ADPLL_CLKCTRL_IDLE);
+	writel_relaxed(v, d->regs + ADPLL_CLKCTRL_OFFSET);
+	spin_unlock_irqrestore(&d->lock, flags);
+}
+
+static void ti_adpll_clear_idle_bypass(struct ti_adpll_data *d)
+{
+	unsigned long flags;
+	u32 v;
+
+	spin_lock_irqsave(&d->lock, flags);
+	v = readl_relaxed(d->regs + ADPLL_CLKCTRL_OFFSET);
+	v &= ~BIT(ADPLL_CLKCTRL_IDLE);
+	writel_relaxed(v, d->regs + ADPLL_CLKCTRL_OFFSET);
+	spin_unlock_irqrestore(&d->lock, flags);
+}
+
+static bool ti_adpll_clock_is_bypass(struct ti_adpll_data *d)
+{
+	u32 v;
+
+	v = readl_relaxed(d->regs + ADPLL_STATUS_OFFSET);
+
+	return v & BIT(ADPLL_STATUS_BYPASS);
+}
+
+/*
+ * Locked and bypass are not actually mutually exclusive:  if you only care
+ * about the DCO clock and not CLKOUT you can clear M2PWDNZ before enabling
+ * the PLL, resulting in status (FREQLOCK | PHASELOCK | BYPASS) after lock.
+ */
+static bool ti_adpll_is_locked(struct ti_adpll_data *d)
+{
+	u32 v = readl_relaxed(d->regs + ADPLL_STATUS_OFFSET);
+
+	return (v & ADPLL_STATUS_PREPARED_MASK) == ADPLL_STATUS_PREPARED_MASK;
+}
+
+static int ti_adpll_wait_lock(struct ti_adpll_data *d)
+{
+	int retries = ADPLL_MAX_RETRIES;
+
+	do {
+		if (ti_adpll_is_locked(d))
+			return 0;
+		usleep_range(200, 300);
+	} while (retries-- <= 0);
+
+	dev_err(d->dev, "pll failed to lock\n");
+	return -ETIMEDOUT;
+}
+
+static int ti_adpll_prepare(struct clk_hw *hw)
+{
+	struct ti_adpll_dco_data *dco = to_dco(hw);
+	struct ti_adpll_data *d = to_adpll(dco);
+
+	ti_adpll_clear_idle_bypass(d);
+	ti_adpll_wait_lock(d);
+
+	return 0;
+}
+
+static void ti_adpll_unprepare(struct clk_hw *hw)
+{
+	struct ti_adpll_dco_data *dco = to_dco(hw);
+	struct ti_adpll_data *d = to_adpll(dco);
+
+	ti_adpll_set_idle_bypass(d);
+}
+
+static int ti_adpll_is_prepared(struct clk_hw *hw)
+{
+	struct ti_adpll_dco_data *dco = to_dco(hw);
+	struct ti_adpll_data *d = to_adpll(dco);
+
+	return ti_adpll_is_locked(d);
+}
+
+/*
+ * Note that the DCO clock is never subject to bypass: if the PLL is off,
+ * dcoclk is low.
+ */
+static unsigned long ti_adpll_recalc_rate(struct clk_hw *hw,
+					  unsigned long parent_rate)
+{
+	struct ti_adpll_dco_data *dco = to_dco(hw);
+	struct ti_adpll_data *d = to_adpll(dco);
+	u32 frac_m, v;
+	long long rate, divider;
+	unsigned long flags;
+
+	if (ti_adpll_clock_is_bypass(d))
+		return 0;
+
+	spin_lock_irqsave(&d->lock, flags);
+	frac_m = readl_relaxed(d->regs + ADPLL_FRACDIV_OFFSET);
+	frac_m &= ADPLL_FRACDIV_FRACTIONALM_MASK;
+	rate = readw_relaxed(d->regs + ADPLL_MN2DIV_OFFSET) << 18;
+	rate += frac_m;
+	rate *= parent_rate;
+	divider = (readw_relaxed(d->regs + ADPLL_M2NDIV_OFFSET) + 1) << 18;
+	spin_unlock_irqrestore(&d->lock, flags);
+
+	do_div(rate, divider);
+
+	if (d->c->is_type_s) {
+		v = readl_relaxed(d->regs + ADPLL_CLKCTRL_OFFSET);
+		if (v & BIT(ADPLL_CLKCTRL_REGM4XEN_ADPLL_S))
+			rate *= 4;
+		rate *= 2;
+	}
+
+	return rate;
+}
+
+/* PLL parent is always clkinp, bypass only affects the children */
+static u8 ti_adpll_get_parent(struct clk_hw *hw)
+{
+	return 0;
+}
+
+static struct clk_ops ti_adpll_ops = {
+	.prepare = ti_adpll_prepare,
+	.unprepare = ti_adpll_unprepare,
+	.is_prepared = ti_adpll_is_prepared,
+	.recalc_rate = ti_adpll_recalc_rate,
+	.get_parent = ti_adpll_get_parent,
+};
+
+static int ti_adpll_init_dco(struct ti_adpll_data *d)
+{
+	struct clk_init_data init;
+	struct clk *clock;
+	const char *postfix;
+	int width, err;
+
+	d->outputs.clks = devm_kzalloc(d->dev, sizeof(struct clk *) *
+				       MAX_ADPLL_OUTPUTS,
+				       GFP_KERNEL);
+	if (!d->outputs.clks)
+		return -ENOMEM;
+
+	if (d->c->output_index < 0)
+		postfix = "dco";
+	else
+		postfix = NULL;
+
+	init.name = ti_adpll_clk_get_name(d, d->c->output_index, postfix);
+	if (!init.name)
+		return -EINVAL;
+
+	init.parent_names = d->parent_names;
+	init.num_parents = d->c->nr_max_inputs;
+	init.ops = &ti_adpll_ops;
+	d->dco.hw.init = &init;
+
+	if (d->c->is_type_s)
+		width = 5;
+	else
+		width = 4;
+
+	/* Internal input clock divider N2 */
+	err = ti_adpll_init_divider(d, TI_ADPLL_N2, -ENODEV, "n2",
+				    d->parent_clocks[TI_ADPLL_CLKINP],
+				    d->regs + ADPLL_MN2DIV_OFFSET,
+				    ADPLL_MN2DIV_N2, width, 0);
+	if (err)
+		return err;
+
+	clock = devm_clk_register(d->dev, &d->dco.hw);
+	if (IS_ERR(clock))
+		return PTR_ERR(clock);
+
+	return ti_adpll_setup_clock(d, clock, TI_ADPLL_DCO, d->c->output_index,
+				    init.name, NULL);
+}
+
+static int ti_adpll_clkout_enable(struct clk_hw *hw)
+{
+	struct ti_adpll_clkout_data *co = to_clkout(hw);
+	struct clk_hw *gate_hw = &co->gate.hw;
+
+	__clk_hw_set_clk(gate_hw, hw);
+
+	return clk_gate_ops.enable(gate_hw);
+}
+
+static void ti_adpll_clkout_disable(struct clk_hw *hw)
+{
+	struct ti_adpll_clkout_data *co = to_clkout(hw);
+	struct clk_hw *gate_hw = &co->gate.hw;
+
+	__clk_hw_set_clk(gate_hw, hw);
+	clk_gate_ops.disable(gate_hw);
+}
+
+static int ti_adpll_clkout_is_enabled(struct clk_hw *hw)
+{
+	struct ti_adpll_clkout_data *co = to_clkout(hw);
+	struct clk_hw *gate_hw = &co->gate.hw;
+
+	__clk_hw_set_clk(gate_hw, hw);
+
+	return clk_gate_ops.is_enabled(gate_hw);
+}
+
+/* Setting PLL bypass puts clkout and clkoutx2 into bypass */
+static u8 ti_adpll_clkout_get_parent(struct clk_hw *hw)
+{
+	struct ti_adpll_clkout_data *co = to_clkout(hw);
+	struct ti_adpll_data *d = co->adpll;
+
+	return ti_adpll_clock_is_bypass(d);
+}
+
+/* Warn if clkout or clkoutx2 try to set unavailable parent */
+static int ti_adpll_clkout_set_parent(struct clk_hw *hw, u8 index)
+{
+	struct ti_adpll_clkout_data *co = to_clkout(hw);
+	struct ti_adpll_data *d = co->adpll;
+
+	if (ti_adpll_clock_is_bypass(d) != index)
+		return -EAGAIN;
+
+	return 0;
+}
+
+static int ti_adpll_init_clkout(struct ti_adpll_data *d,
+				enum ti_adpll_clocks index,
+				int output_index, int gate_bit,
+				char *name, struct clk *clk0,
+				struct clk *clk1)
+{
+	struct ti_adpll_clkout_data *co;
+	struct clk_init_data init;
+	struct clk_ops *ops;
+	const char *parent_names[2];
+	const char *child_name;
+	struct clk *clock;
+	int err;
+
+	co = devm_kzalloc(d->dev, sizeof(*co), GFP_KERNEL);
+	if (!co)
+		return -ENOMEM;
+	co->adpll = d;
+
+	err = of_property_read_string_index(d->np,
+					    "clock-output-names",
+					    output_index,
+					    &child_name);
+	if (err)
+		return err;
+
+	ops = devm_kzalloc(d->dev, sizeof(*ops), GFP_KERNEL);
+	if (!ops)
+		return -ENOMEM;
+
+	init.name = child_name;
+	init.ops = ops;
+	init.flags = CLK_IS_BASIC;
+	co->hw.init = &init;
+	parent_names[0] = __clk_get_name(clk0);
+	parent_names[1] = __clk_get_name(clk1);
+	init.parent_names = parent_names;
+	init.num_parents = 2;
+
+	ops->get_parent = ti_adpll_clkout_get_parent;
+	ops->set_parent = ti_adpll_clkout_set_parent;
+	ops->determine_rate = __clk_mux_determine_rate;
+	if (gate_bit) {
+		co->gate.lock = &d->lock;
+		co->gate.reg = d->regs + ADPLL_CLKCTRL_OFFSET;
+		co->gate.bit_idx = gate_bit;
+		ops->enable = ti_adpll_clkout_enable;
+		ops->disable = ti_adpll_clkout_disable;
+		ops->is_enabled = ti_adpll_clkout_is_enabled;
+	}
+
+	clock = devm_clk_register(d->dev, &co->hw);
+	if (IS_ERR(clock)) {
+		dev_err(d->dev, "failed to register output %s: %li\n",
+			name, PTR_ERR(clock));
+		return PTR_ERR(clock);
+	}
+
+	return ti_adpll_setup_clock(d, clock, index, output_index, child_name,
+				    NULL);
+}
+
+static int ti_adpll_init_children_adpll_s(struct ti_adpll_data *d)
+{
+	int err;
+
+	if (!d->c->is_type_s)
+		return 0;
+
+	/* Internal mux, sources from divider N2 or clkinpulow */
+	err = ti_adpll_init_mux(d, TI_ADPLL_BYPASS, "bypass",
+				d->clocks[TI_ADPLL_N2].clk,
+				d->parent_clocks[TI_ADPLL_CLKINPULOW],
+				d->regs + ADPLL_CLKCTRL_OFFSET,
+				ADPLL_CLKCTRL_ULOWCLKEN);
+	if (err)
+		return err;
+
+	/* Internal divider M2, sources DCO */
+	err = ti_adpll_init_divider(d, TI_ADPLL_M2, -ENODEV, "m2",
+				    d->clocks[TI_ADPLL_DCO].clk,
+				    d->regs + ADPLL_M2NDIV_OFFSET,
+				    ADPLL_M2NDIV_M2,
+				    ADPLL_M2NDIV_M2_ADPLL_S_WIDTH,
+				    CLK_DIVIDER_ONE_BASED);
+	if (err)
+		return err;
+
+	/* Internal fixed divider, after M2 before clkout */
+	err = ti_adpll_init_fixed_factor(d, TI_ADPLL_DIV2, "div2",
+					 d->clocks[TI_ADPLL_M2].clk,
+					 1, 2);
+	if (err)
+		return err;
+
+	/* Output clkout with a mux and gate, sources from div2 or bypass */
+	err = ti_adpll_init_clkout(d, TI_ADPLL_CLKOUT, TI_ADPLL_S_CLKOUT,
+				   ADPLL_CLKCTRL_CLKOUTEN, "clkout",
+				   d->clocks[TI_ADPLL_DIV2].clk,
+				   d->clocks[TI_ADPLL_BYPASS].clk);
+	if (err)
+		return err;
+
+	/* Output clkoutx2 with a mux and gate, sources from M2 or bypass */
+	err = ti_adpll_init_clkout(d, TI_ADPLL_CLKOUT2, TI_ADPLL_S_CLKOUTX2, 0,
+				   "clkout2", d->clocks[TI_ADPLL_M2].clk,
+				   d->clocks[TI_ADPLL_BYPASS].clk);
+	if (err)
+		return err;
+
+	/* Internal mux, sources from DCO and clkinphf */
+	if (d->parent_clocks[TI_ADPLL_CLKINPHIF]) {
+		err = ti_adpll_init_mux(d, TI_ADPLL_HIF, "hif",
+					d->clocks[TI_ADPLL_DCO].clk,
+					d->parent_clocks[TI_ADPLL_CLKINPHIF],
+					d->regs + ADPLL_CLKCTRL_OFFSET,
+					ADPLL_CLKINPHIFSEL_ADPLL_S);
+		if (err)
+			return err;
+	}
+
+	/* Output clkouthif with a divider M3, sources from hif */
+	err = ti_adpll_init_divider(d, TI_ADPLL_M3, TI_ADPLL_S_CLKOUTHIF, "m3",
+				    d->clocks[TI_ADPLL_HIF].clk,
+				    d->regs + ADPLL_M3DIV_OFFSET,
+				    ADPLL_M3DIV_M3,
+				    ADPLL_M3DIV_M3_WIDTH,
+				    CLK_DIVIDER_ONE_BASED);
+	if (err)
+		return err;
+
+	/* Output clock dcoclkldo is the DCO */
+
+	return 0;
+}
+
+static int ti_adpll_init_children_adpll_lj(struct ti_adpll_data *d)
+{
+	int err;
+
+	if (d->c->is_type_s)
+		return 0;
+
+	/* Output clkdcoldo, gated output of DCO */
+	err = ti_adpll_init_gate(d, TI_ADPLL_DCO_GATE, TI_ADPLL_LJ_CLKDCOLDO,
+				 "clkdcoldo", d->clocks[TI_ADPLL_DCO].clk,
+				 d->regs + ADPLL_CLKCTRL_OFFSET,
+				 ADPLL_CLKCTRL_CLKDCOLDOEN, 0);
+	if (err)
+		return err;
+
+	/* Internal divider M2, sources from DCO */
+	err = ti_adpll_init_divider(d, TI_ADPLL_M2, -ENODEV,
+				    "m2", d->clocks[TI_ADPLL_DCO].clk,
+				    d->regs + ADPLL_M2NDIV_OFFSET,
+				    ADPLL_M2NDIV_M2,
+				    ADPLL_M2NDIV_M2_ADPLL_LJ_WIDTH,
+				    CLK_DIVIDER_ONE_BASED);
+	if (err)
+		return err;
+
+	/* Output clkoutldo, gated output of M2 */
+	err = ti_adpll_init_gate(d, TI_ADPLL_M2_GATE, TI_ADPLL_LJ_CLKOUTLDO,
+				 "clkoutldo", d->clocks[TI_ADPLL_M2].clk,
+				 d->regs + ADPLL_CLKCTRL_OFFSET,
+				 ADPLL_CLKCTRL_CLKOUTLDOEN_ADPLL_LJ,
+				 0);
+	if (err)
+		return err;
+
+	/* Internal mux, sources from divider N2 or clkinpulow */
+	err = ti_adpll_init_mux(d, TI_ADPLL_BYPASS, "bypass",
+				d->clocks[TI_ADPLL_N2].clk,
+				d->parent_clocks[TI_ADPLL_CLKINPULOW],
+				d->regs + ADPLL_CLKCTRL_OFFSET,
+				ADPLL_CLKCTRL_ULOWCLKEN);
+	if (err)
+		return err;
+
+	/* Output clkout, sources M2 or bypass */
+	err = ti_adpll_init_clkout(d, TI_ADPLL_CLKOUT, TI_ADPLL_S_CLKOUT,
+				   ADPLL_CLKCTRL_CLKOUTEN, "clkout",
+				   d->clocks[TI_ADPLL_M2].clk,
+				   d->clocks[TI_ADPLL_BYPASS].clk);
+	if (err)
+		return err;
+
+	return 0;
+}
+
+static void ti_adpll_free_resources(struct ti_adpll_data *d)
+{
+	int i;
+
+	for (i = TI_ADPLL_M3; i >= 0; i--) {
+		struct ti_adpll_clock *ac = &d->clocks[i];
+
+		if (!ac || IS_ERR_OR_NULL(ac->clk))
+			continue;
+		if (ac->cl)
+			clkdev_drop(ac->cl);
+		if (ac->unregister)
+			ac->unregister(ac->clk);
+	}
+}
+
+/* MPU PLL manages the lock register for all PLLs */
+static void ti_adpll_unlock_all(void __iomem *reg)
+{
+	u32 v;
+
+	v = readl_relaxed(reg);
+	if (v == ADPLL_PLLSS_MMR_LOCK_ENABLED)
+		writel_relaxed(ADPLL_PLLSS_MMR_UNLOCK_MAGIC, reg);
+}
+
+static int ti_adpll_init_registers(struct ti_adpll_data *d)
+{
+	int register_offset = 0;
+
+	if (d->c->is_type_s) {
+		register_offset = 8;
+		ti_adpll_unlock_all(d->iobase + ADPLL_PLLSS_MMR_LOCK_OFFSET);
+	}
+
+	d->regs = d->iobase + register_offset + ADPLL_PWRCTRL_OFFSET;
+
+	return 0;
+}
+
+static int ti_adpll_init_inputs(struct ti_adpll_data *d)
+{
+	const char *error = "need at least %i inputs";
+	struct clk *clock;
+	int nr_inputs;
+
+	nr_inputs = of_clk_get_parent_count(d->np);
+	if (nr_inputs < d->c->nr_max_inputs) {
+		dev_err(d->dev, error, nr_inputs);
+		return -EINVAL;
+	}
+	of_clk_parent_fill(d->np, d->parent_names, nr_inputs);
+
+	clock = devm_clk_get(d->dev, d->parent_names[0]);
+	if (IS_ERR(clock)) {
+		dev_err(d->dev, "could not get clkinp\n");
+		return PTR_ERR(clock);
+	}
+	d->parent_clocks[TI_ADPLL_CLKINP] = clock;
+
+	clock = devm_clk_get(d->dev, d->parent_names[1]);
+	if (IS_ERR(clock)) {
+		dev_err(d->dev, "could not get clkinpulow clock\n");
+		return PTR_ERR(clock);
+	}
+	d->parent_clocks[TI_ADPLL_CLKINPULOW] = clock;
+
+	if (d->c->is_type_s) {
+		clock =  devm_clk_get(d->dev, d->parent_names[2]);
+		if (IS_ERR(clock)) {
+			dev_err(d->dev, "could not get clkinphif clock\n");
+			return PTR_ERR(clock);
+		}
+		d->parent_clocks[TI_ADPLL_CLKINPHIF] = clock;
+	}
+
+	return 0;
+}
+
+static const struct ti_adpll_platform_data ti_adpll_type_s = {
+	.is_type_s = true,
+	.nr_max_inputs = MAX_ADPLL_INPUTS,
+	.nr_max_outputs = MAX_ADPLL_OUTPUTS,
+	.output_index = TI_ADPLL_S_DCOCLKLDO,
+};
+
+static const struct ti_adpll_platform_data ti_adpll_type_lj = {
+	.is_type_s = false,
+	.nr_max_inputs = MAX_ADPLL_INPUTS - 1,
+	.nr_max_outputs = MAX_ADPLL_OUTPUTS - 1,
+	.output_index = -EINVAL,
+};
+
+static const struct of_device_id ti_adpll_match[] = {
+	{ .compatible = "ti,dm814-adpll-s-clock", &ti_adpll_type_s },
+	{ .compatible = "ti,dm814-adpll-lj-clock", &ti_adpll_type_lj },
+	{},
+};
+MODULE_DEVICE_TABLE(of, ti_adpll_match);
+
+static int ti_adpll_probe(struct platform_device *pdev)
+{
+	struct device_node *node = pdev->dev.of_node;
+	struct device *dev = &pdev->dev;
+	const struct of_device_id *match;
+	const struct ti_adpll_platform_data *pdata;
+	struct ti_adpll_data *d;
+	struct resource *res;
+	int err;
+
+	match = of_match_device(ti_adpll_match, dev);
+	if (match)
+		pdata = match->data;
+	else
+		return -ENODEV;
+
+	d = devm_kzalloc(dev, sizeof(*d), GFP_KERNEL);
+	if (!d)
+		return -ENOMEM;
+	d->dev = dev;
+	d->np = node;
+	d->c = pdata;
+	dev_set_drvdata(d->dev, d);
+	spin_lock_init(&d->lock);
+
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	if (!res)
+		return -ENODEV;
+	d->pa = res->start;
+
+	d->iobase = devm_ioremap_resource(dev, res);
+	if (IS_ERR(d->iobase)) {
+		dev_err(dev, "could not get IO base: %li\n",
+			PTR_ERR(d->iobase));
+		return PTR_ERR(d->iobase);
+	}
+
+	err = ti_adpll_init_registers(d);
+	if (err)
+		return err;
+
+	err = ti_adpll_init_inputs(d);
+	if (err)
+		return err;
+
+	d->clocks = devm_kzalloc(d->dev, sizeof(struct ti_adpll_clock) *
+				 TI_ADPLL_NR_CLOCKS,
+				 GFP_KERNEL);
+	if (!d->clocks)
+		goto free;
+
+	err = ti_adpll_init_dco(d);
+	if (err) {
+		dev_err(dev, "could not register dco: %i\n", err);
+		goto free;
+	}
+
+	err = ti_adpll_init_children_adpll_s(d);
+	if (err)
+		goto free;
+	err = ti_adpll_init_children_adpll_lj(d);
+	if (err)
+		goto free;
+
+	err = of_clk_add_provider(d->np, of_clk_src_onecell_get, &d->outputs);
+	if (err)
+		goto free;
+
+	return 0;
+
+free:
+	WARN_ON(1);
+	ti_adpll_free_resources(d);
+
+	return err;
+}
+
+static int ti_adpll_remove(struct platform_device *pdev)
+{
+	struct ti_adpll_data *d = dev_get_drvdata(&pdev->dev);
+
+	ti_adpll_free_resources(d);
+
+	return 0;
+}
+
+static struct platform_driver ti_adpll_driver = {
+	.driver = {
+		.name = "ti-adpll",
+		.of_match_table = ti_adpll_match,
+	},
+	.probe = ti_adpll_probe,
+	.remove = ti_adpll_remove,
+};
+
+static int __init ti_adpll_init(void)
+{
+	return platform_driver_register(&ti_adpll_driver);
+}
+core_initcall(ti_adpll_init);
+
+static void __exit ti_adpll_exit(void)
+{
+	platform_driver_unregister(&ti_adpll_driver);
+}
+module_exit(ti_adpll_exit);
+
+MODULE_DESCRIPTION("Clock driver for dm814x ADPLL");
+MODULE_ALIAS("platform:dm814-adpll-clock");
+MODULE_AUTHOR("Tony LIndgren <tony@atomide.com>");
+MODULE_LICENSE("GPL v2");
diff --git a/drivers/clk/ti/clk-814x.c b/drivers/clk/ti/clk-814x.c
index 9e85fcc..2323643 100644
--- a/drivers/clk/ti/clk-814x.c
+++ b/drivers/clk/ti/clk-814x.c
@@ -5,8 +5,10 @@
  */
 
 #include <linux/kernel.h>
+#include <linux/clk.h>
 #include <linux/clk-provider.h>
 #include <linux/clk/ti.h>
+#include <linux/of_platform.h>
 
 #include "clock.h"
 
@@ -27,11 +29,62 @@ static struct ti_dt_clk dm814_clks[] = {
 	{ .node_name = NULL },
 };
 
+static bool timer_clocks_initialized;
+
+int __init dm814x_adpll_early_init(void)
+{
+	struct device_node *np;
+
+	if (!timer_clocks_initialized)
+		return -ENODEV;
+
+	np = of_find_node_by_name(NULL, "pllss");
+	if (!np) {
+		pr_err("Could not find node for plls\n");
+		return -ENODEV;
+	}
+
+	of_platform_populate(np, NULL, NULL, NULL);
+
+	return 0;
+}
+core_initcall(dm814x_adpll_early_init);
+
+static const char * const init_clocks[] = {
+	"pll040clkout",		/* MPU 481c5040.adpll.clkout */
+	"pll290clkout",		/* DDR 481c5290.adpll.clkout */
+};
+
+int __init dm814x_adpll_enable_init_clocks(void)
+{
+	int i, err;
+
+	if (!timer_clocks_initialized)
+		return -ENODEV;
+
+	for (i = 0; i < ARRAY_SIZE(init_clocks); i++) {
+		struct clk *clock;
+
+		clock = clk_get(NULL, init_clocks[i]);
+		if (WARN(IS_ERR(clock), "could not find init clock %s\n",
+			 init_clocks[i]))
+			continue;
+		err = clk_prepare_enable(clock);
+		if (WARN(err, "could not enable init clock %s\n",
+			 init_clocks[i]))
+			continue;
+	}
+
+	return 0;
+}
+postcore_initcall(dm814x_adpll_enable_init_clocks);
+
 int __init dm814x_dt_clk_init(void)
 {
 	ti_dt_clocks_register(dm814_clks);
 	omap2_clk_disable_autoidle_all();
 	omap2_clk_enable_init_clocks(NULL, 0);
+	timer_clocks_initialized = true;
 
 	return 0;
 }
-- 
2.6.2