From: "Lothar Waßmann" <LW@KARO-electronics.de> To: Alexandre Belloni <alexandre.belloni@free-electrons.com>, Ian Campbell <ijc+devicetree@hellion.org.uk>, Jean-Christophe Plagniol-Villard <plagnioj@jcrosoft.com>, Kumar Gala <galak@codeaurora.org>, Mark Rutland <mark.rutland@arm.com>, Nicolas Ferre <nicolas.ferre@atmel.com>, Pawel Moll <pawel.moll@arm.com>, Rob Herring <robh+dt@kernel.org>, Russell King <linux@arm.linux.org.uk>, devicetree@vger.kernel.org, linux-arm-kernel@lists.infradead.org, linux-kernel@vger.kernel.org Cc: "Lothar Waßmann" <LW@KARO-electronics.de> Subject: [PATCH 3/3] ARM: dts: sama5d4: add support for Ka-Ro electronics TXA5 modules Date: Wed, 20 Jan 2016 13:35:37 +0100 [thread overview] Message-ID: <1453293337-16078-4-git-send-email-LW@KARO-electronics.de> (raw) In-Reply-To: <1453293337-16078-1-git-send-email-LW@KARO-electronics.de> The TXA5-5010/-5011 are Computers On Module manufactured by Ka-Ro electronics GmbH with the following characteristics: Processor Atmel SAMA5D42, 528 MHz RAM 256MB 32-bit DDR2 SDRAM ROM 128MB NAND Flash (TXA5-5010) / 4GB eMMC (TXA5-5011) Power supply Single 3.1V to 5.5V Size 26mm SO-DIMM Temp. Range -40°C/-25°C to 85°C Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de> --- arch/arm/boot/dts/Makefile | 1 + arch/arm/boot/dts/at91-sama5d4-txa5-5010.dts | 217 +++++++++++++++++++++++++++ 2 files changed, 218 insertions(+) create mode 100644 arch/arm/boot/dts/at91-sama5d4-txa5-5010.dts diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile index a4a6d70..8fbc0cb 100644 --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile @@ -49,6 +49,7 @@ dtb-$(CONFIG_SOC_SAM_V7) += \ sama5d35ek.dtb \ sama5d36ek.dtb \ at91-sama5d4_ma5d4evk.dtb \ + at91-sama5d4-txa5-5010.dtb \ at91-sama5d4_xplained.dtb \ at91-sama5d4ek.dtb \ at91-vinco.dtb diff --git a/arch/arm/boot/dts/at91-sama5d4-txa5-5010.dts b/arch/arm/boot/dts/at91-sama5d4-txa5-5010.dts new file mode 100644 index 0000000..fb4a253 --- /dev/null +++ b/arch/arm/boot/dts/at91-sama5d4-txa5-5010.dts @@ -0,0 +1,217 @@ +/* + * at91-sama5d4-txa5.dts - Device Tree file for Ka-Ro electronics TXA5 module + * + * Copyright (C) 2015 Lothar Waßmann <LW@KARO-electronics.de> + * based on: at91-sama5d4_xplained.dts + * Copyright (C) 2015 Atmel, + * 2015 Josh Wu <josh.wu@atmel.com> + * + * This file is dual-licensed: you can use it either under the terms + * of the GPL or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. + * + * a) This file is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of the + * License, or (at your option) any later version. + * + * This file is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * Or, alternatively, + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use, + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. + */ +/dts-v1/; +#include "sama5d4.dtsi" +#include <dt-bindings/input/input.h> +#include <dt-bindings/pwm/pwm.h> + +/ { + model = "Ka-Ro SAMA5D4 TXA5"; + compatible = "atmel,sama5d4-txa5", "atmel,sama5d4", "atmel,sama5"; + + aliases { + display = &display; + ethernet0 = &macb0; + serial0 = &usart0; + serial1 = &usart1; + serial2 = &usart3; + spi0 = &spi0; + }; + + clocks { + #address-cells = <1>; + #size-cells = <1>; + ranges; + + main_clock: clock@0 { + compatible = "atmel,osc", "fixed-clock"; + clock-frequency = <12000000>; + }; + }; + + backlight: backlight { + compatible = "pwm-backlight"; + pwms = <&hlcdc_pwm 0 500000 PWM_POLARITY_INVERTED>; + }; + + display: display { + display-timings { + }; + }; + + leds { + compatible = "gpio-leds"; + status = "okay"; + + heartbeat { + label = "heartbeat"; + gpios = <&pioD 29 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "heartbeat"; + }; + }; +}; + +&adc0 { + atmel,adc-vref = <3300>; + status = "okay"; +}; + +&hlcdc { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_lcd_rgb888>; + status = "okay"; +}; + +&i2c1 { + status = "okay"; +}; + +&macb0 { + phy-mode = "rmii"; + status = "okay"; + + phy0: ethernet-phy@1 { + interrupt-parent = <&pioE>; + interrupts = <1 IRQ_TYPE_EDGE_FALLING>; + reg = <1>; + }; +}; + +&main_xtal { + clock-frequency = <12000000>; +}; + +&mmc1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_mmc1_clk_cmd_dat0 &pinctrl_mmc1_dat1_3 &pinctrl_mmc1_cd>; + status = "okay"; + slot@0 { + reg = <0>; + bus-width = <4>; + cd-gpios = <&pioE 3 0>; + }; +}; + +&nand0 { + nand-bus-width = <8>; + nand-ecc-mode = "hw"; + nand-on-flash-bbt; + atmel,has-pmecc; + status = "okay"; +}; + +&pinctrl { + sama5d4-txa5 { + pinctrl_mmc1_cd: mmc1-cd { + atmel,pins = <AT91_PIOE 6 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP_DEGLITCH>; + }; + + pinctrl_spi0_cs: spi0 { + atmel,pins = < + AT91_PIOB 21 AT91_PERIPH_GPIO 0 /* CSPI_SS0 */ + AT91_PIOB 22 AT91_PERIPH_GPIO 0 /* CSPI_SS1 */ + AT91_PIOB 23 AT91_PERIPH_GPIO 0 /* CSPI_RDY */ + >; + }; + + pinctrl_usba_vbus: usba-vbus { + atmel,pins = < + AT91_PIOE 10 AT91_PERIPH_GPIO 0 /* USBOTG_VBUSEN */ + AT91_PIOD 8 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP_DEGLITCH /* USBOTG_OC */ + >; + }; + + pinctrl_usbb_vbus: usbb-vbus { + atmel,pins = < + AT91_PIOE 11 AT91_PERIPH_GPIO 0 /* USBH_VBUSEN */ + AT91_PIOD 9 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP_DEGLITCH /* USBH_OC */ + >; + }; + }; +}; + +&slow_xtal { + clock-frequency = <32768>; +}; + +&spi0 { + cs-gpios = <&pioB 21 0>, <&pioB 22 0>, <0>, <0>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_spi0 &pinctrl_spi0_cs>; + status = "okay"; +}; + +&usart0 { + status = "okay"; +}; + +&usart1 { + status = "okay"; +}; + +&usart3 { + status = "okay"; +}; + +&usb0 { + atmel,vbus-gpio = <&pioE 10 GPIO_ACTIVE_HIGH>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usba_vbus>; + status = "okay"; +}; + +&usb1 { + num-ports = <1>; + atmel,vbus-gpio = <&pioE 11 GPIO_ACTIVE_HIGH>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usbb_vbus>; + status = "okay"; +}; + +&watchdog { + status = "okay"; +}; -- 2.1.4
WARNING: multiple messages have this Message-ID (diff)
From: LW@KARO-electronics.de (Lothar Waßmann) To: linux-arm-kernel@lists.infradead.org Subject: [PATCH 3/3] ARM: dts: sama5d4: add support for Ka-Ro electronics TXA5 modules Date: Wed, 20 Jan 2016 13:35:37 +0100 [thread overview] Message-ID: <1453293337-16078-4-git-send-email-LW@KARO-electronics.de> (raw) In-Reply-To: <1453293337-16078-1-git-send-email-LW@KARO-electronics.de> The TXA5-5010/-5011 are Computers On Module manufactured by Ka-Ro electronics GmbH with the following characteristics: Processor Atmel SAMA5D42, 528 MHz RAM 256MB 32-bit DDR2 SDRAM ROM 128MB NAND Flash (TXA5-5010) / 4GB eMMC (TXA5-5011) Power supply Single 3.1V to 5.5V Size 26mm SO-DIMM Temp. Range -40?C/-25?C to 85?C Signed-off-by: Lothar Wa?mann <LW@KARO-electronics.de> --- arch/arm/boot/dts/Makefile | 1 + arch/arm/boot/dts/at91-sama5d4-txa5-5010.dts | 217 +++++++++++++++++++++++++++ 2 files changed, 218 insertions(+) create mode 100644 arch/arm/boot/dts/at91-sama5d4-txa5-5010.dts diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile index a4a6d70..8fbc0cb 100644 --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile @@ -49,6 +49,7 @@ dtb-$(CONFIG_SOC_SAM_V7) += \ sama5d35ek.dtb \ sama5d36ek.dtb \ at91-sama5d4_ma5d4evk.dtb \ + at91-sama5d4-txa5-5010.dtb \ at91-sama5d4_xplained.dtb \ at91-sama5d4ek.dtb \ at91-vinco.dtb diff --git a/arch/arm/boot/dts/at91-sama5d4-txa5-5010.dts b/arch/arm/boot/dts/at91-sama5d4-txa5-5010.dts new file mode 100644 index 0000000..fb4a253 --- /dev/null +++ b/arch/arm/boot/dts/at91-sama5d4-txa5-5010.dts @@ -0,0 +1,217 @@ +/* + * at91-sama5d4-txa5.dts - Device Tree file for Ka-Ro electronics TXA5 module + * + * Copyright (C) 2015 Lothar Wa?mann <LW@KARO-electronics.de> + * based on: at91-sama5d4_xplained.dts + * Copyright (C) 2015 Atmel, + * 2015 Josh Wu <josh.wu@atmel.com> + * + * This file is dual-licensed: you can use it either under the terms + * of the GPL or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. + * + * a) This file is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of the + * License, or (at your option) any later version. + * + * This file is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * Or, alternatively, + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use, + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. + */ +/dts-v1/; +#include "sama5d4.dtsi" +#include <dt-bindings/input/input.h> +#include <dt-bindings/pwm/pwm.h> + +/ { + model = "Ka-Ro SAMA5D4 TXA5"; + compatible = "atmel,sama5d4-txa5", "atmel,sama5d4", "atmel,sama5"; + + aliases { + display = &display; + ethernet0 = &macb0; + serial0 = &usart0; + serial1 = &usart1; + serial2 = &usart3; + spi0 = &spi0; + }; + + clocks { + #address-cells = <1>; + #size-cells = <1>; + ranges; + + main_clock: clock at 0 { + compatible = "atmel,osc", "fixed-clock"; + clock-frequency = <12000000>; + }; + }; + + backlight: backlight { + compatible = "pwm-backlight"; + pwms = <&hlcdc_pwm 0 500000 PWM_POLARITY_INVERTED>; + }; + + display: display { + display-timings { + }; + }; + + leds { + compatible = "gpio-leds"; + status = "okay"; + + heartbeat { + label = "heartbeat"; + gpios = <&pioD 29 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "heartbeat"; + }; + }; +}; + +&adc0 { + atmel,adc-vref = <3300>; + status = "okay"; +}; + +&hlcdc { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_lcd_rgb888>; + status = "okay"; +}; + +&i2c1 { + status = "okay"; +}; + +&macb0 { + phy-mode = "rmii"; + status = "okay"; + + phy0: ethernet-phy at 1 { + interrupt-parent = <&pioE>; + interrupts = <1 IRQ_TYPE_EDGE_FALLING>; + reg = <1>; + }; +}; + +&main_xtal { + clock-frequency = <12000000>; +}; + +&mmc1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_mmc1_clk_cmd_dat0 &pinctrl_mmc1_dat1_3 &pinctrl_mmc1_cd>; + status = "okay"; + slot at 0 { + reg = <0>; + bus-width = <4>; + cd-gpios = <&pioE 3 0>; + }; +}; + +&nand0 { + nand-bus-width = <8>; + nand-ecc-mode = "hw"; + nand-on-flash-bbt; + atmel,has-pmecc; + status = "okay"; +}; + +&pinctrl { + sama5d4-txa5 { + pinctrl_mmc1_cd: mmc1-cd { + atmel,pins = <AT91_PIOE 6 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP_DEGLITCH>; + }; + + pinctrl_spi0_cs: spi0 { + atmel,pins = < + AT91_PIOB 21 AT91_PERIPH_GPIO 0 /* CSPI_SS0 */ + AT91_PIOB 22 AT91_PERIPH_GPIO 0 /* CSPI_SS1 */ + AT91_PIOB 23 AT91_PERIPH_GPIO 0 /* CSPI_RDY */ + >; + }; + + pinctrl_usba_vbus: usba-vbus { + atmel,pins = < + AT91_PIOE 10 AT91_PERIPH_GPIO 0 /* USBOTG_VBUSEN */ + AT91_PIOD 8 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP_DEGLITCH /* USBOTG_OC */ + >; + }; + + pinctrl_usbb_vbus: usbb-vbus { + atmel,pins = < + AT91_PIOE 11 AT91_PERIPH_GPIO 0 /* USBH_VBUSEN */ + AT91_PIOD 9 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP_DEGLITCH /* USBH_OC */ + >; + }; + }; +}; + +&slow_xtal { + clock-frequency = <32768>; +}; + +&spi0 { + cs-gpios = <&pioB 21 0>, <&pioB 22 0>, <0>, <0>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_spi0 &pinctrl_spi0_cs>; + status = "okay"; +}; + +&usart0 { + status = "okay"; +}; + +&usart1 { + status = "okay"; +}; + +&usart3 { + status = "okay"; +}; + +&usb0 { + atmel,vbus-gpio = <&pioE 10 GPIO_ACTIVE_HIGH>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usba_vbus>; + status = "okay"; +}; + +&usb1 { + num-ports = <1>; + atmel,vbus-gpio = <&pioE 11 GPIO_ACTIVE_HIGH>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usbb_vbus>; + status = "okay"; +}; + +&watchdog { + status = "okay"; +}; -- 2.1.4
next prev parent reply other threads:[~2016-01-20 12:37 UTC|newest] Thread overview: 26+ messages / expand[flat|nested] mbox.gz Atom feed top 2016-01-20 12:35 ARM: dts: sama5d4: add support for Ka-Ro electronics TXA5 modules Lothar Waßmann 2016-01-20 12:35 ` Lothar Waßmann 2016-01-20 12:35 ` [PATCH 1/3] ARM: dts: sama5d4: cleanup - add blank lines between pinctrl nodes Lothar Waßmann 2016-01-20 12:35 ` Lothar Waßmann 2016-01-25 11:18 ` Alexandre Belloni 2016-01-25 11:18 ` Alexandre Belloni 2016-01-25 11:18 ` Alexandre Belloni 2016-01-25 13:35 ` Nicolas Ferre 2016-01-25 13:35 ` Nicolas Ferre 2016-01-25 13:35 ` Nicolas Ferre 2016-01-20 12:35 ` [PATCH 2/3] ARM: dts: sama5d4: add labels for watchdog and " Lothar Waßmann 2016-01-20 12:35 ` Lothar Waßmann 2016-01-25 11:19 ` Alexandre Belloni 2016-01-25 11:19 ` Alexandre Belloni 2016-01-25 11:19 ` Alexandre Belloni 2016-01-25 13:35 ` Nicolas Ferre 2016-01-25 13:35 ` Nicolas Ferre 2016-01-25 13:35 ` Nicolas Ferre 2016-01-20 12:35 ` Lothar Waßmann [this message] 2016-01-20 12:35 ` [PATCH 3/3] ARM: dts: sama5d4: add support for Ka-Ro electronics TXA5 modules Lothar Waßmann 2016-01-25 11:34 ` Alexandre Belloni 2016-01-25 11:34 ` Alexandre Belloni 2016-01-25 11:34 ` Alexandre Belloni 2016-01-25 13:40 ` Nicolas Ferre 2016-01-25 13:40 ` Nicolas Ferre 2016-01-25 13:40 ` Nicolas Ferre
Reply instructions: You may reply publicly to this message via plain-text email using any one of the following methods: * Save the following mbox file, import it into your mail client, and reply-to-all from there: mbox Avoid top-posting and favor interleaved quoting: https://en.wikipedia.org/wiki/Posting_style#Interleaved_style * Reply using the --to, --cc, and --in-reply-to switches of git-send-email(1): git send-email \ --in-reply-to=1453293337-16078-4-git-send-email-LW@KARO-electronics.de \ --to=lw@karo-electronics.de \ --cc=alexandre.belloni@free-electrons.com \ --cc=devicetree@vger.kernel.org \ --cc=galak@codeaurora.org \ --cc=ijc+devicetree@hellion.org.uk \ --cc=linux-arm-kernel@lists.infradead.org \ --cc=linux-kernel@vger.kernel.org \ --cc=linux@arm.linux.org.uk \ --cc=mark.rutland@arm.com \ --cc=nicolas.ferre@atmel.com \ --cc=pawel.moll@arm.com \ --cc=plagnioj@jcrosoft.com \ --cc=robh+dt@kernel.org \ /path/to/YOUR_REPLY https://kernel.org/pub/software/scm/git/docs/git-send-email.html * If your mail client supports setting the In-Reply-To header via mailto: links, try the mailto: linkBe sure your reply has a Subject: header at the top and a blank line before the message body.
This is an external index of several public inboxes, see mirroring instructions on how to clone and mirror all data and code used by this external index.