From: Chanwoo Choi <cw00.choi@samsung.com> To: k.kozlowski@samsung.com, kgene@kernel.org Cc: linux-samsung-soc@vger.kernel.org, linux-arm-kernel@lists.infradead.org, linux-kernel@vger.kernel.org, devicetree@vger.kernel.org, Chanwoo Choi <cw00.choi@samsung.com>, Kukjin Kim <kgene.kim@samsung.com> Subject: [PATCH] ARM: dts: Add initial pin configuration for exynos3250-rinato Date: Mon, 14 Mar 2016 10:12:54 +0900 [thread overview] Message-ID: <1457917974-314-1-git-send-email-cw00.choi@samsung.com> (raw) This patch adds initial pin configuration using pinctrl subsystem to reduce leakage power-consumption of gpio pins in normal state. All pins included in this patch are NC (not connected) pin. Cc: Kukjin Kim <kgene.kim@samsung.com> Cc: Krzysztof Kozlowski <k.kozlowski@samsung.com> Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com> --- arch/arm/boot/dts/exynos3250-pinctrl.dtsi | 38 +++++++++++++++++ arch/arm/boot/dts/exynos3250-rinato.dts | 70 ++++++++++++++++++++++++++++++- 2 files changed, 106 insertions(+), 2 deletions(-) diff --git a/arch/arm/boot/dts/exynos3250-pinctrl.dtsi b/arch/arm/boot/dts/exynos3250-pinctrl.dtsi index 5ab81c39e2c9..ecf79386e891 100644 --- a/arch/arm/boot/dts/exynos3250-pinctrl.dtsi +++ b/arch/arm/boot/dts/exynos3250-pinctrl.dtsi @@ -16,11 +16,49 @@ #define PIN_PULL_DOWN 1 #define PIN_PULL_UP 3 +#define PIN_DRV_LV1 0 +#define PIN_DRV_LV2 2 +#define PIN_DRV_LV3 1 +#define PIN_DRV_LV4 3 + #define PIN_PDN_OUT0 0 #define PIN_PDN_OUT1 1 #define PIN_PDN_INPUT 2 #define PIN_PDN_PREV 3 +#define PIN_IN(_pin, _pull, _drv) \ + _pin { \ + samsung,pins = #_pin; \ + samsung,pin-function = <0>; \ + samsung,pin-pud = <PIN_PULL_ ##_pull>; \ + samsung,pin-drv = <PIN_DRV_ ##_drv>; \ + } + +#define PIN_OUT(_pin, _drv) \ + _pin { \ + samsung,pins = #_pin; \ + samsung,pin-function = <1>; \ + samsung,pin-pud = <0>; \ + samsung,pin-drv = <PIN_DRV_ ##_drv>; \ + } + +#define PIN_OUT_SET(_pin, _val, _drv) \ + _pin { \ + samsung,pins = #_pin; \ + samsung,pin-function = <1>; \ + samsung,pin-pud = <0>; \ + samsung,pin-drv = <PIN_DRV_ ##_drv>; \ + samsung,pin-val = <_val>; \ + } + +#define PIN_CFG(_pin, _sel, _pull, _drv) \ + _pin { \ + samsung,pins = #_pin; \ + samsung,pin-function = <_sel>; \ + samsung,pin-pud = <PIN_PULL_ ##_pull>; \ + samsung,pin-drv = <PIN_DRV_ ##_drv>; \ + } + #define PIN_SLP(_pin, _mode, _pull) \ _pin { \ samsung,pins = #_pin; \ diff --git a/arch/arm/boot/dts/exynos3250-rinato.dts b/arch/arm/boot/dts/exynos3250-rinato.dts index 3e64d5dcdd60..1c78a2153776 100644 --- a/arch/arm/boot/dts/exynos3250-rinato.dts +++ b/arch/arm/boot/dts/exynos3250-rinato.dts @@ -681,7 +681,21 @@ &pinctrl_0 { pinctrl-names = "default"; - pinctrl-0 = <&sleep0>; + pinctrl-0 = <&initial0 &sleep0>; + + initial0: initial-state { + PIN_IN(gpa1-4, DOWN, LV1); + PIN_IN(gpa1-5, DOWN, LV1); + + PIN_IN(gpc0-0, DOWN, LV1); + PIN_IN(gpc0-1, DOWN, LV1); + PIN_IN(gpc0-2, DOWN, LV1); + PIN_IN(gpc0-3, DOWN, LV1); + PIN_IN(gpc0-4, DOWN, LV1); + + PIN_IN(gpd0-0, DOWN, LV1); + PIN_IN(gpd0-1, DOWN, LV1); + }; sleep0: sleep-state { PIN_SLP(gpa0-0, INPUT, DOWN); @@ -735,7 +749,59 @@ &pinctrl_1 { pinctrl-names = "default"; - pinctrl-0 = <&sleep1>; + pinctrl-0 = <&initial1 &sleep1>; + + initial1: initial-state { + PIN_IN(gpe0-6, DOWN, LV1); + PIN_IN(gpe0-7, DOWN, LV1); + + PIN_IN(gpe1-0, DOWN, LV1); + PIN_IN(gpe1-3, DOWN, LV1); + PIN_IN(gpe1-4, DOWN, LV1); + PIN_IN(gpe1-5, DOWN, LV1); + PIN_IN(gpe1-6, DOWN, LV1); + + PIN_IN(gpk2-0, DOWN, LV1); + PIN_IN(gpk2-1, DOWN, LV1); + PIN_IN(gpk2-2, DOWN, LV1); + PIN_IN(gpk2-3, DOWN, LV1); + PIN_IN(gpk2-4, DOWN, LV1); + PIN_IN(gpk2-5, DOWN, LV1); + PIN_IN(gpk2-6, DOWN, LV1); + + PIN_IN(gpm0-0, DOWN, LV1); + PIN_IN(gpm0-1, DOWN, LV1); + PIN_IN(gpm0-2, DOWN, LV1); + PIN_IN(gpm0-3, DOWN, LV1); + PIN_IN(gpm0-4, DOWN, LV1); + PIN_IN(gpm0-5, DOWN, LV1); + PIN_IN(gpm0-6, DOWN, LV1); + PIN_IN(gpm0-7, DOWN, LV1); + + PIN_IN(gpm1-0, DOWN, LV1); + PIN_IN(gpm1-1, DOWN, LV1); + PIN_IN(gpm1-2, DOWN, LV1); + PIN_IN(gpm1-3, DOWN, LV1); + PIN_IN(gpm1-4, DOWN, LV1); + PIN_IN(gpm1-5, DOWN, LV1); + PIN_IN(gpm1-6, DOWN, LV1); + PIN_IN(gpm2-0, DOWN, LV1); + PIN_IN(gpm2-1, DOWN, LV1); + + PIN_IN(gpm3-0, DOWN, LV1); + PIN_IN(gpm3-1, DOWN, LV1); + PIN_IN(gpm3-2, DOWN, LV1); + PIN_IN(gpm3-3, DOWN, LV1); + PIN_IN(gpm3-4, DOWN, LV1); + + PIN_IN(gpm4-1, DOWN, LV1); + PIN_IN(gpm4-2, DOWN, LV1); + PIN_IN(gpm4-3, DOWN, LV1); + PIN_IN(gpm4-4, DOWN, LV1); + PIN_IN(gpm4-5, DOWN, LV1); + PIN_IN(gpm4-6, DOWN, LV1); + PIN_IN(gpm4-7, DOWN, LV1); + }; sleep1: sleep-state { PIN_SLP(gpe0-0, PREV, NONE); -- 1.9.1
WARNING: multiple messages have this Message-ID (diff)
From: cw00.choi@samsung.com (Chanwoo Choi) To: linux-arm-kernel@lists.infradead.org Subject: [PATCH] ARM: dts: Add initial pin configuration for exynos3250-rinato Date: Mon, 14 Mar 2016 10:12:54 +0900 [thread overview] Message-ID: <1457917974-314-1-git-send-email-cw00.choi@samsung.com> (raw) This patch adds initial pin configuration using pinctrl subsystem to reduce leakage power-consumption of gpio pins in normal state. All pins included in this patch are NC (not connected) pin. Cc: Kukjin Kim <kgene.kim@samsung.com> Cc: Krzysztof Kozlowski <k.kozlowski@samsung.com> Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com> --- arch/arm/boot/dts/exynos3250-pinctrl.dtsi | 38 +++++++++++++++++ arch/arm/boot/dts/exynos3250-rinato.dts | 70 ++++++++++++++++++++++++++++++- 2 files changed, 106 insertions(+), 2 deletions(-) diff --git a/arch/arm/boot/dts/exynos3250-pinctrl.dtsi b/arch/arm/boot/dts/exynos3250-pinctrl.dtsi index 5ab81c39e2c9..ecf79386e891 100644 --- a/arch/arm/boot/dts/exynos3250-pinctrl.dtsi +++ b/arch/arm/boot/dts/exynos3250-pinctrl.dtsi @@ -16,11 +16,49 @@ #define PIN_PULL_DOWN 1 #define PIN_PULL_UP 3 +#define PIN_DRV_LV1 0 +#define PIN_DRV_LV2 2 +#define PIN_DRV_LV3 1 +#define PIN_DRV_LV4 3 + #define PIN_PDN_OUT0 0 #define PIN_PDN_OUT1 1 #define PIN_PDN_INPUT 2 #define PIN_PDN_PREV 3 +#define PIN_IN(_pin, _pull, _drv) \ + _pin { \ + samsung,pins = #_pin; \ + samsung,pin-function = <0>; \ + samsung,pin-pud = <PIN_PULL_ ##_pull>; \ + samsung,pin-drv = <PIN_DRV_ ##_drv>; \ + } + +#define PIN_OUT(_pin, _drv) \ + _pin { \ + samsung,pins = #_pin; \ + samsung,pin-function = <1>; \ + samsung,pin-pud = <0>; \ + samsung,pin-drv = <PIN_DRV_ ##_drv>; \ + } + +#define PIN_OUT_SET(_pin, _val, _drv) \ + _pin { \ + samsung,pins = #_pin; \ + samsung,pin-function = <1>; \ + samsung,pin-pud = <0>; \ + samsung,pin-drv = <PIN_DRV_ ##_drv>; \ + samsung,pin-val = <_val>; \ + } + +#define PIN_CFG(_pin, _sel, _pull, _drv) \ + _pin { \ + samsung,pins = #_pin; \ + samsung,pin-function = <_sel>; \ + samsung,pin-pud = <PIN_PULL_ ##_pull>; \ + samsung,pin-drv = <PIN_DRV_ ##_drv>; \ + } + #define PIN_SLP(_pin, _mode, _pull) \ _pin { \ samsung,pins = #_pin; \ diff --git a/arch/arm/boot/dts/exynos3250-rinato.dts b/arch/arm/boot/dts/exynos3250-rinato.dts index 3e64d5dcdd60..1c78a2153776 100644 --- a/arch/arm/boot/dts/exynos3250-rinato.dts +++ b/arch/arm/boot/dts/exynos3250-rinato.dts @@ -681,7 +681,21 @@ &pinctrl_0 { pinctrl-names = "default"; - pinctrl-0 = <&sleep0>; + pinctrl-0 = <&initial0 &sleep0>; + + initial0: initial-state { + PIN_IN(gpa1-4, DOWN, LV1); + PIN_IN(gpa1-5, DOWN, LV1); + + PIN_IN(gpc0-0, DOWN, LV1); + PIN_IN(gpc0-1, DOWN, LV1); + PIN_IN(gpc0-2, DOWN, LV1); + PIN_IN(gpc0-3, DOWN, LV1); + PIN_IN(gpc0-4, DOWN, LV1); + + PIN_IN(gpd0-0, DOWN, LV1); + PIN_IN(gpd0-1, DOWN, LV1); + }; sleep0: sleep-state { PIN_SLP(gpa0-0, INPUT, DOWN); @@ -735,7 +749,59 @@ &pinctrl_1 { pinctrl-names = "default"; - pinctrl-0 = <&sleep1>; + pinctrl-0 = <&initial1 &sleep1>; + + initial1: initial-state { + PIN_IN(gpe0-6, DOWN, LV1); + PIN_IN(gpe0-7, DOWN, LV1); + + PIN_IN(gpe1-0, DOWN, LV1); + PIN_IN(gpe1-3, DOWN, LV1); + PIN_IN(gpe1-4, DOWN, LV1); + PIN_IN(gpe1-5, DOWN, LV1); + PIN_IN(gpe1-6, DOWN, LV1); + + PIN_IN(gpk2-0, DOWN, LV1); + PIN_IN(gpk2-1, DOWN, LV1); + PIN_IN(gpk2-2, DOWN, LV1); + PIN_IN(gpk2-3, DOWN, LV1); + PIN_IN(gpk2-4, DOWN, LV1); + PIN_IN(gpk2-5, DOWN, LV1); + PIN_IN(gpk2-6, DOWN, LV1); + + PIN_IN(gpm0-0, DOWN, LV1); + PIN_IN(gpm0-1, DOWN, LV1); + PIN_IN(gpm0-2, DOWN, LV1); + PIN_IN(gpm0-3, DOWN, LV1); + PIN_IN(gpm0-4, DOWN, LV1); + PIN_IN(gpm0-5, DOWN, LV1); + PIN_IN(gpm0-6, DOWN, LV1); + PIN_IN(gpm0-7, DOWN, LV1); + + PIN_IN(gpm1-0, DOWN, LV1); + PIN_IN(gpm1-1, DOWN, LV1); + PIN_IN(gpm1-2, DOWN, LV1); + PIN_IN(gpm1-3, DOWN, LV1); + PIN_IN(gpm1-4, DOWN, LV1); + PIN_IN(gpm1-5, DOWN, LV1); + PIN_IN(gpm1-6, DOWN, LV1); + PIN_IN(gpm2-0, DOWN, LV1); + PIN_IN(gpm2-1, DOWN, LV1); + + PIN_IN(gpm3-0, DOWN, LV1); + PIN_IN(gpm3-1, DOWN, LV1); + PIN_IN(gpm3-2, DOWN, LV1); + PIN_IN(gpm3-3, DOWN, LV1); + PIN_IN(gpm3-4, DOWN, LV1); + + PIN_IN(gpm4-1, DOWN, LV1); + PIN_IN(gpm4-2, DOWN, LV1); + PIN_IN(gpm4-3, DOWN, LV1); + PIN_IN(gpm4-4, DOWN, LV1); + PIN_IN(gpm4-5, DOWN, LV1); + PIN_IN(gpm4-6, DOWN, LV1); + PIN_IN(gpm4-7, DOWN, LV1); + }; sleep1: sleep-state { PIN_SLP(gpe0-0, PREV, NONE); -- 1.9.1
next reply other threads:[~2016-03-14 1:13 UTC|newest] Thread overview: 4+ messages / expand[flat|nested] mbox.gz Atom feed top 2016-03-14 1:12 Chanwoo Choi [this message] 2016-03-14 1:12 ` [PATCH] ARM: dts: Add initial pin configuration for exynos3250-rinato Chanwoo Choi 2016-03-14 6:03 ` Krzysztof Kozlowski 2016-03-14 6:03 ` Krzysztof Kozlowski
Reply instructions: You may reply publicly to this message via plain-text email using any one of the following methods: * Save the following mbox file, import it into your mail client, and reply-to-all from there: mbox Avoid top-posting and favor interleaved quoting: https://en.wikipedia.org/wiki/Posting_style#Interleaved_style * Reply using the --to, --cc, and --in-reply-to switches of git-send-email(1): git send-email \ --in-reply-to=1457917974-314-1-git-send-email-cw00.choi@samsung.com \ --to=cw00.choi@samsung.com \ --cc=devicetree@vger.kernel.org \ --cc=k.kozlowski@samsung.com \ --cc=kgene.kim@samsung.com \ --cc=kgene@kernel.org \ --cc=linux-arm-kernel@lists.infradead.org \ --cc=linux-kernel@vger.kernel.org \ --cc=linux-samsung-soc@vger.kernel.org \ /path/to/YOUR_REPLY https://kernel.org/pub/software/scm/git/docs/git-send-email.html * If your mail client supports setting the In-Reply-To header via mailto: links, try the mailto: linkBe sure your reply has a Subject: header at the top and a blank line before the message body.
This is an external index of several public inboxes, see mirroring instructions on how to clone and mirror all data and code used by this external index.