[PATCH 1/2] ARM: dts: Add support for dra72-evm rev C (ES2.0)

[Nishanth Menon <nm@ti.com>]

DRA72-EVM now has an upgrade to Rev C with ES2.0 silicon. As part of
this change, a few updates were factored in that were software
incompatible with previous board in few areas:
- We now use DP83867 ethernet phy instead of older DP838865 which fails
  in certain usecases.
- Two ethernet ports now instead of the single one in rev B.
- polarities changed for certain pcf gpios
- Due to SoC phy current requirements, VDDA supplies are split between
 ldo5 and ldo2 (ldo2 was previously unused). NOTE: DSS (VDDA_VIDEO) is
 still supplied by ldo5.

NOTE: It does not make much sense to spin off a new board compatible
flag since there is no real benefit for the same.

Signed-off-by: Nishanth Menon <nm@ti.com>
---
 arch/arm/boot/dts/Makefile                         |   3 +-
 .../dts/{dra72-evm.dts => dra72-evm-common.dtsi}   |  26 +-
 arch/arm/boot/dts/dra72-evm-revc.dts               |  73 ++
 arch/arm/boot/dts/dra72-evm.dts                    | 835 +--------------------
 4 files changed, 89 insertions(+), 848 deletions(-)
 copy arch/arm/boot/dts/{dra72-evm.dts => dra72-evm-common.dtsi} (97%)
 create mode 100644 arch/arm/boot/dts/dra72-evm-revc.dts

diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index b25621ae2ff7..f74bd41cf58c 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -527,7 +527,8 @@ dtb-$(CONFIG_SOC_DRA7XX) += \
 	am57xx-cl-som-am57x.dtb \
 	am57xx-sbc-am57x.dtb \
 	dra7-evm.dtb \
-	dra72-evm.dtb
+	dra72-evm.dtb \
+	dra72-evm-revc.dtb
 dtb-$(CONFIG_ARCH_ORION5X) += \
 	orion5x-lacie-d2-network.dtb \
 	orion5x-lacie-ethernet-disk-mini-v2.dtb \
diff --git a/arch/arm/boot/dts/dra72-evm.dts b/arch/arm/boot/dts/dra72-evm-common.dtsi
similarity index 97%
copy from arch/arm/boot/dts/dra72-evm.dts
copy to arch/arm/boot/dts/dra72-evm-common.dtsi
index 6affe2d137da..94faab98cf0d 100644
--- a/arch/arm/boot/dts/dra72-evm.dts
+++ b/arch/arm/boot/dts/dra72-evm-common.dtsi
@@ -12,14 +12,8 @@
 #include <dt-bindings/clk/ti-dra7-atl.h>
 
 / {
-	model = "TI DRA722";
 	compatible = "ti,dra72-evm", "ti,dra722", "ti,dra72", "ti,dra7";
 
-	memory {
-		device_type = "memory";
-		reg = <0x0 0x80000000 0x0 0x40000000>; /* 1024 MB */
-	};
-
 	aliases {
 		display0 = &hdmi0;
 	};
@@ -320,7 +314,7 @@
 		tps65917_pmic {
 			compatible = "ti,tps65917-pmic";
 
-			regulators {
+			tps65917_regulators: regulators {
 				smps1_reg: smps1 {
 					/* VDD_MPU */
 					regulator-name = "smps1";
@@ -376,14 +370,6 @@
 					regulator-allow-bypass;
 				};
 
-				ldo2_reg: ldo2 {
-					/* LDO2_OUT --> TP1017 (UNUSED)  */
-					regulator-name = "ldo2";
-					regulator-min-microvolt = <1800000>;
-					regulator-max-microvolt = <3300000>;
-					regulator-allow-bypass;
-				};
-
 				ldo3_reg: ldo3 {
 					/* VDDA_1V8_PHY */
 					regulator-name = "ldo3";
@@ -427,8 +413,6 @@
 		lines-initial-states = <0x1408>;
 		gpio-controller;
 		#gpio-cells = <2>;
-		interrupt-parent = <&gpio6>;
-		interrupts = <11 IRQ_TYPE_EDGE_FALLING>;
 		interrupt-controller;
 		#interrupt-cells = <2>;
 	};
@@ -689,13 +673,6 @@
 	pinctrl-names = "default", "sleep";
 	pinctrl-0 = <&cpsw_default>;
 	pinctrl-1 = <&cpsw_sleep>;
-	slaves = <1>;
-	mode-gpios = <&pcf_gpio_21 4 GPIO_ACTIVE_HIGH>;
-};
-
-&cpsw_emac0 {
-	phy_id = <&davinci_mdio>, <3>;
-	phy-mode = "rgmii";
 };
 
 &davinci_mdio {
@@ -785,7 +762,6 @@
 
 &hdmi {
 	status = "ok";
-	vdda-supply = <&ldo3_reg>;
 
 	pinctrl-names = "default";
 	pinctrl-0 = <&hdmi_pins>;
diff --git a/arch/arm/boot/dts/dra72-evm-revc.dts b/arch/arm/boot/dts/dra72-evm-revc.dts
new file mode 100644
index 000000000000..23a3e60f22dc
--- /dev/null
+++ b/arch/arm/boot/dts/dra72-evm-revc.dts
@@ -0,0 +1,73 @@
+/*
+ * Copyright (C) 2016 Texas Instruments Incorporated - http://www.ti.com/
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+#include "dra72-evm-common.dtsi"
+#include <dt-bindings/net/ti-dp83867.h>
+
+/ {
+	model = "TI DRA722 Rev C EVM";
+
+	memory {
+		device_type = "memory";
+		reg = <0x0 0x80000000 0x0 0x80000000>; /* 2GB */
+	};
+};
+
+&tps65917_regulators {
+	ldo2_reg: ldo2 {
+		/* LDO2_OUT --> VDDA_1V8_PHY2 */
+		regulator-name = "ldo2";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		regulator-always-on;
+		regulator-boot-on;
+	};
+};
+
+&hdmi {
+	vdda_video-supply = <&ldo2_reg>;
+};
+
+&pcf_gpio_21 {
+	interrupt-parent = <&gpio3>;
+	interrupts = <30 IRQ_TYPE_EDGE_FALLING>;
+};
+
+&mac {
+	mode-gpios = <&pcf_gpio_21 4 GPIO_ACTIVE_LOW>,
+		     <&pcf_hdmi 9 GPIO_ACTIVE_LOW>,	/* P11 */
+		     <&pcf_hdmi 10 GPIO_ACTIVE_LOW>;	/* P12 */
+	dual_emac;
+};
+
+&cpsw_emac0 {
+	phy_id = <&davinci_mdio>, <2>;
+	phy-mode = "rgmii-id";
+	dual_emac_res_vlan = <1>;
+};
+
+&cpsw_emac1 {
+	phy_id = <&davinci_mdio>, <3>;
+	phy-mode = "rgmii-id";
+	dual_emac_res_vlan = <2>;
+};
+
+&davinci_mdio {
+	dp83867_0: ethernet-phy@2 {
+		reg = <2>;
+		ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_00_NS>;
+		ti,tx-internal-delay = <DP83867_RGMIIDCTL_1_NS>;
+		ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_8_B_NIB>;
+	};
+
+	dp83867_1: ethernet-phy@3 {
+		reg = <3>;
+		ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_00_NS>;
+		ti,tx-internal-delay = <DP83867_RGMIIDCTL_1_NS>;
+		ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_8_B_NIB>;
+	};
+};
diff --git a/arch/arm/boot/dts/dra72-evm.dts b/arch/arm/boot/dts/dra72-evm.dts
index 6affe2d137da..89fe7ba8ae01 100644
--- a/arch/arm/boot/dts/dra72-evm.dts
+++ b/arch/arm/boot/dts/dra72-evm.dts
@@ -1,694 +1,40 @@
 /*
- * Copyright (C) 2014 Texas Instruments Incorporated - http://www.ti.com/
+ * Copyright (C) 2014-2016 Texas Instruments Incorporated - http://www.ti.com/
  *
  * This program is free software; you can redistribute it and/or modify
  * it under the terms of the GNU General Public License version 2 as
  * published by the Free Software Foundation.
  */
-/dts-v1/;
-
-#include "dra72x.dtsi"
-#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/clk/ti-dra7-atl.h>
-
+#include "dra72-evm-common.dtsi"
 / {
 	model = "TI DRA722";
-	compatible = "ti,dra72-evm", "ti,dra722", "ti,dra72", "ti,dra7";
 
 	memory {
 		device_type = "memory";
 		reg = <0x0 0x80000000 0x0 0x40000000>; /* 1024 MB */
 	};
+};
 
-	aliases {
-		display0 = &hdmi0;
-	};
-
-	evm_3v3: fixedregulator-evm_3v3 {
-		compatible = "regulator-fixed";
-		regulator-name = "evm_3v3";
-		regulator-min-microvolt = <3300000>;
-		regulator-max-microvolt = <3300000>;
-	};
-
-	aic_dvdd: fixedregulator-aic_dvdd {
-		/* TPS77018DBVT */
-		compatible = "regulator-fixed";
-		regulator-name = "aic_dvdd";
-		vin-supply = <&evm_3v3>;
+&tps65917_regulators {
+	ldo2_reg: ldo2 {
+		/* LDO2_OUT --> TP1017 (UNUSED)  */
+		regulator-name = "ldo2";
 		regulator-min-microvolt = <1800000>;
-		regulator-max-microvolt = <1800000>;
-	};
-
-	evm_3v3_sd: fixedregulator-sd {
-		compatible = "regulator-fixed";
-		regulator-name = "evm_3v3_sd";
-		regulator-min-microvolt = <3300000>;
 		regulator-max-microvolt = <3300000>;
-		enable-active-high;
-		gpio = <&pcf_gpio_21 5 GPIO_ACTIVE_HIGH>;
-	};
-
-	extcon_usb1: extcon_usb1 {
-		compatible = "linux,extcon-usb-gpio";
-		id-gpio = <&pcf_gpio_21 1 GPIO_ACTIVE_HIGH>;
-	};
-
-	extcon_usb2: extcon_usb2 {
-		compatible = "linux,extcon-usb-gpio";
-		id-gpio = <&pcf_gpio_21 2 GPIO_ACTIVE_HIGH>;
-	};
-
-	hdmi0: connector {
-		compatible = "hdmi-connector";
-		label = "hdmi";
-
-		type = "a";
-
-		port {
-			hdmi_connector_in: endpoint {
-				remote-endpoint = <&tpd12s015_out>;
-			};
-		};
-	};
-
-	tpd12s015: encoder {
-		compatible = "ti,tpd12s015";
-
-		pinctrl-names = "default";
-		pinctrl-0 = <&tpd12s015_pins>;
-
-		gpios = <&pcf_hdmi 4 GPIO_ACTIVE_HIGH>,	/* P4, CT CP HPD */
-			<&pcf_hdmi 5 GPIO_ACTIVE_HIGH>,	/* P5, LS OE */
-			<&gpio7 12 GPIO_ACTIVE_HIGH>;	/* gpio7_12/sp1_cs2, HPD */
-
-		ports {
-			#address-cells = <1>;
-			#size-cells = <0>;
-
-			port@0 {
-				reg = <0>;
-
-				tpd12s015_in: endpoint {
-					remote-endpoint = <&hdmi_out>;
-				};
-			};
-
-			port@1 {
-				reg = <1>;
-
-				tpd12s015_out: endpoint {
-					remote-endpoint = <&hdmi_connector_in>;
-				};
-			};
-		};
-	};
-
-	sound0: sound@0 {
-		compatible = "simple-audio-card";
-		simple-audio-card,name = "DRA7xx-EVM";
-		simple-audio-card,widgets =
-			"Headphone", "Headphone Jack",
-			"Line", "Line Out",
-			"Microphone", "Mic Jack",
-			"Line", "Line In";
-		simple-audio-card,routing =
-			"Headphone Jack",       "HPLOUT",
-			"Headphone Jack",       "HPROUT",
-			"Line Out",		"LLOUT",
-			"Line Out",		"RLOUT",
-			"MIC3L",		"Mic Jack",
-			"MIC3R",		"Mic Jack",
-			"Mic Jack",		"Mic Bias",
-			"LINE1L",               "Line In",
-			"LINE1R",               "Line In";
-		simple-audio-card,format = "dsp_b";
-		simple-audio-card,bitclock-master = <&sound0_master>;
-		simple-audio-card,frame-master = <&sound0_master>;
-		simple-audio-card,bitclock-inversion;
-
-		sound0_master: simple-audio-card,cpu {
-			sound-dai = <&mcasp3>;
-			system-clock-frequency = <5644800>;
-		};
-
-		simple-audio-card,codec {
-			sound-dai = <&tlv320aic3106>;
-			clocks = <&atl_clkin2_ck>;
-		};
-	};
-};
-
-&dra7_pmx_core {
-	i2c1_pins: pinmux_i2c1_pins {
-		pinctrl-single,pins = <
-			DRA7XX_CORE_IOPAD(0x3800, PIN_INPUT | MUX_MODE0) /* i2c1_sda.i2c1_sda */
-			DRA7XX_CORE_IOPAD(0x3804, PIN_INPUT | MUX_MODE0) /* i2c1_scl.i2c1_scl */
-		>;
-	};
-
-	i2c5_pins: pinmux_i2c5_pins {
-		pinctrl-single,pins = <
-			DRA7XX_CORE_IOPAD(0x36b4, PIN_INPUT | MUX_MODE10) /* mcasp1_axr0.i2c5_sda */
-			DRA7XX_CORE_IOPAD(0x36b8, PIN_INPUT | MUX_MODE10) /* mcasp1_axr1.i2c5_scl */
-		>;
-	};
-
-	i2c5_pins: pinmux_i2c5_pins {
-		pinctrl-single,pins = <
-			DRA7XX_CORE_IOPAD(0x36b4, PIN_INPUT | MUX_MODE10) /* mcasp1_axr0.i2c5_sda */
-			DRA7XX_CORE_IOPAD(0x36b8, PIN_INPUT | MUX_MODE10) /* mcasp1_axr1.i2c5_scl */
-		>;
-	};
-
-	nand_default: nand_default {
-		pinctrl-single,pins = <
-			DRA7XX_CORE_IOPAD(0x3400, PIN_INPUT  | MUX_MODE0) /* gpmc_ad0 */
-			DRA7XX_CORE_IOPAD(0x3404, PIN_INPUT  | MUX_MODE0) /* gpmc_ad1 */
-			DRA7XX_CORE_IOPAD(0x3408, PIN_INPUT  | MUX_MODE0) /* gpmc_ad2 */
-			DRA7XX_CORE_IOPAD(0x340c, PIN_INPUT  | MUX_MODE0) /* gpmc_ad3 */
-			DRA7XX_CORE_IOPAD(0x3410, PIN_INPUT  | MUX_MODE0) /* gpmc_ad4 */
-			DRA7XX_CORE_IOPAD(0x3414, PIN_INPUT  | MUX_MODE0) /* gpmc_ad5 */
-			DRA7XX_CORE_IOPAD(0x3418, PIN_INPUT  | MUX_MODE0) /* gpmc_ad6 */
-			DRA7XX_CORE_IOPAD(0x341c, PIN_INPUT  | MUX_MODE0) /* gpmc_ad7 */
-			DRA7XX_CORE_IOPAD(0x3420, PIN_INPUT  | MUX_MODE0) /* gpmc_ad8 */
-			DRA7XX_CORE_IOPAD(0x3424, PIN_INPUT  | MUX_MODE0) /* gpmc_ad9 */
-			DRA7XX_CORE_IOPAD(0x3428, PIN_INPUT  | MUX_MODE0) /* gpmc_ad10 */
-			DRA7XX_CORE_IOPAD(0x342c, PIN_INPUT  | MUX_MODE0) /* gpmc_ad11 */
-			DRA7XX_CORE_IOPAD(0x3430, PIN_INPUT  | MUX_MODE0) /* gpmc_ad12 */
-			DRA7XX_CORE_IOPAD(0x3434, PIN_INPUT  | MUX_MODE0) /* gpmc_ad13 */
-			DRA7XX_CORE_IOPAD(0x3438, PIN_INPUT  | MUX_MODE0) /* gpmc_ad14 */
-			DRA7XX_CORE_IOPAD(0x343c, PIN_INPUT  | MUX_MODE0) /* gpmc_ad15 */
-			DRA7XX_CORE_IOPAD(0x34b4, PIN_OUTPUT | MUX_MODE0) /* gpmc_cs0 */
-			DRA7XX_CORE_IOPAD(0x34c4, PIN_OUTPUT | MUX_MODE0) /* gpmc_advn_ale */
-			DRA7XX_CORE_IOPAD(0x34cc, PIN_OUTPUT | MUX_MODE0) /* gpmc_wen */
-			DRA7XX_CORE_IOPAD(0x34c8, PIN_OUTPUT | MUX_MODE0) /* gpmc_oen_ren */
-			DRA7XX_CORE_IOPAD(0x34d0, PIN_OUTPUT | MUX_MODE0) /* gpmc_ben0 */
-			DRA7XX_CORE_IOPAD(0x34d8, PIN_INPUT  | MUX_MODE0) /* gpmc_wait0 */
-		>;
-	};
-
-	usb1_pins: pinmux_usb1_pins {
-		pinctrl-single,pins = <
-			DRA7XX_CORE_IOPAD(0x3680, PIN_INPUT_SLEW | MUX_MODE0) /* usb1_drvvbus */
-		>;
-	};
-
-	usb2_pins: pinmux_usb2_pins {
-		pinctrl-single,pins = <
-			DRA7XX_CORE_IOPAD(0x3684, PIN_INPUT_SLEW | MUX_MODE0) /* usb2_drvvbus */
-		>;
-	};
-
-	tps65917_pins_default: tps65917_pins_default {
-		pinctrl-single,pins = <
-			DRA7XX_CORE_IOPAD(0x3824, PIN_INPUT_PULLUP | MUX_MODE1) /* wakeup3.sys_nirq1 */
-		>;
-	};
-
-	mmc1_pins_default: mmc1_pins_default {
-		pinctrl-single,pins = <
-			DRA7XX_CORE_IOPAD(0x376c, PIN_INPUT | MUX_MODE14)	/* mmc1sdcd.gpio219 */
-			DRA7XX_CORE_IOPAD(0x3754, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_clk.clk */
-			DRA7XX_CORE_IOPAD(0x3758, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_cmd.cmd */
-			DRA7XX_CORE_IOPAD(0x375c, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat0.dat0 */
-			DRA7XX_CORE_IOPAD(0x3760, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat1.dat1 */
-			DRA7XX_CORE_IOPAD(0x3764, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat2.dat2 */
-			DRA7XX_CORE_IOPAD(0x3768, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat3.dat3 */
-		>;
-	};
-
-	mmc2_pins_default: mmc2_pins_default {
-		pinctrl-single,pins = <
-			DRA7XX_CORE_IOPAD(0x349c, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a23.mmc2_clk */
-			DRA7XX_CORE_IOPAD(0x34b0, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_cs1.mmc2_cmd */
-			DRA7XX_CORE_IOPAD(0x34a0, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a24.mmc2_dat0 */
-			DRA7XX_CORE_IOPAD(0x34a4, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a25.mmc2_dat1 */
-			DRA7XX_CORE_IOPAD(0x34a8, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a26.mmc2_dat2 */
-			DRA7XX_CORE_IOPAD(0x34ac, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a27.mmc2_dat3 */
-			DRA7XX_CORE_IOPAD(0x348c, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a19.mmc2_dat4 */
-			DRA7XX_CORE_IOPAD(0x3490, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a20.mmc2_dat5 */
-			DRA7XX_CORE_IOPAD(0x3494, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a21.mmc2_dat6 */
-			DRA7XX_CORE_IOPAD(0x3498, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a22.mmc2_dat7 */
-		>;
-	};
-
-	dcan1_pins_default: dcan1_pins_default {
-		pinctrl-single,pins = <
-			DRA7XX_CORE_IOPAD(0x37d0, PIN_OUTPUT_PULLUP | MUX_MODE0) /* dcan1_tx */
-			DRA7XX_CORE_IOPAD(0x3818, PULL_UP | MUX_MODE1)	/* wakeup0.dcan1_rx */
-		>;
-	};
-
-	dcan1_pins_sleep: dcan1_pins_sleep {
-		pinctrl-single,pins = <
-			DRA7XX_CORE_IOPAD(0x37d0, MUX_MODE15 | PULL_UP)	/* dcan1_tx.off */
-			DRA7XX_CORE_IOPAD(0x3818, MUX_MODE15 | PULL_UP)	/* wakeup0.off */
-		>;
-	};
-
-	qspi1_pins: pinmux_qspi1_pins {
-		pinctrl-single,pins = <
-			DRA7XX_CORE_IOPAD(0x3474, PIN_OUTPUT | MUX_MODE1)	/* gpmc_a13.qspi1_rtclk */
-			DRA7XX_CORE_IOPAD(0x3478, PIN_INPUT | MUX_MODE1)	/* gpmc_a14.qspi1_d3 */
-			DRA7XX_CORE_IOPAD(0x347c, PIN_INPUT | MUX_MODE1)	/* gpmc_a15.qspi1_d2 */
-			DRA7XX_CORE_IOPAD(0x3480, PIN_INPUT | MUX_MODE1)	/* gpmc_a16.qspi1_d1 */
-			DRA7XX_CORE_IOPAD(0x3484, PIN_INPUT | MUX_MODE1)	/* gpmc_a17.qspi1_d0 */
-			DRA7XX_CORE_IOPAD(0x3488, PIN_OUTPUT | MUX_MODE1)	/* qpmc_a18.qspi1_sclk */
-			DRA7XX_CORE_IOPAD(0x34b8, PIN_OUTPUT | MUX_MODE1)	/* gpmc_cs2.qspi1_cs0 */
-		>;
-	};
-
-	hdmi_pins: pinmux_hdmi_pins {
-		pinctrl-single,pins = <
-			DRA7XX_CORE_IOPAD(0x3808, PIN_INPUT | MUX_MODE1) /* i2c2_sda.hdmi1_ddc_scl */
-			DRA7XX_CORE_IOPAD(0x380c, PIN_INPUT | MUX_MODE1) /* i2c2_scl.hdmi1_ddc_sda */
-		>;
-	};
-
-	tpd12s015_pins: pinmux_tpd12s015_pins {
-		pinctrl-single,pins = <
-			DRA7XX_CORE_IOPAD(0x37b8, PIN_INPUT_PULLDOWN | MUX_MODE14) /* gpio7_12 HPD */
-		>;
-	};
-
-	atl_pins: pinmux_atl_pins {
-		pinctrl-single,pins = <
-			DRA7XX_CORE_IOPAD(0x3698, PIN_OUTPUT | MUX_MODE5)	/* xref_clk1.atl_clk1 */
-			DRA7XX_CORE_IOPAD(0x369c, PIN_OUTPUT | MUX_MODE5)	/* xref_clk2.atl_clk2 */
-		>;
-	};
-
-	mcasp3_pins: pinmux_mcasp3_pins {
-		pinctrl-single,pins = <
-			DRA7XX_CORE_IOPAD(0x3724, PIN_OUTPUT_PULLDOWN | MUX_MODE0)	/* mcasp3_aclkx */
-			DRA7XX_CORE_IOPAD(0x3728, PIN_OUTPUT_PULLDOWN | MUX_MODE0)	/* mcasp3_fsx */
-			DRA7XX_CORE_IOPAD(0x372c, PIN_OUTPUT_PULLDOWN | MUX_MODE0)	/* mcasp3_axr0 */
-			DRA7XX_CORE_IOPAD(0x3730, PIN_INPUT_PULLDOWN | MUX_MODE0)	/* mcasp3_axr1 */
-		>;
-	};
-
-	mcasp3_sleep_pins: pinmux_mcasp3_sleep_pins {
-		pinctrl-single,pins = <
-			DRA7XX_CORE_IOPAD(0x3724, PIN_INPUT_PULLDOWN | MUX_MODE15)
-			DRA7XX_CORE_IOPAD(0x3728, PIN_INPUT_PULLDOWN | MUX_MODE15)
-			DRA7XX_CORE_IOPAD(0x372c, PIN_INPUT_PULLDOWN | MUX_MODE15)
-			DRA7XX_CORE_IOPAD(0x3730, PIN_INPUT_PULLDOWN | MUX_MODE15)
-		>;
-	};
-};
-
-&i2c1 {
-	status = "okay";
-	pinctrl-names = "default";
-	pinctrl-0 = <&i2c1_pins>;
-	clock-frequency = <400000>;
-
-	tps65917: tps65917@58 {
-		compatible = "ti,tps65917";
-		reg = <0x58>;
-
-		pinctrl-names = "default";
-		pinctrl-0 = <&tps65917_pins_default>;
-
-		interrupts = <GIC_SPI 2 IRQ_TYPE_NONE>;  /* IRQ_SYS_1N */
-		interrupt-controller;
-		#interrupt-cells = <2>;
-
-		ti,system-power-controller;
-
-		tps65917_pmic {
-			compatible = "ti,tps65917-pmic";
-
-			regulators {
-				smps1_reg: smps1 {
-					/* VDD_MPU */
-					regulator-name = "smps1";
-					regulator-min-microvolt = <850000>;
-					regulator-max-microvolt = <1250000>;
-					regulator-always-on;
-					regulator-boot-on;
-				};
-
-				smps2_reg: smps2 {
-					/* VDD_CORE */
-					regulator-name = "smps2";
-					regulator-min-microvolt = <850000>;
-					regulator-max-microvolt = <1060000>;
-					regulator-boot-on;
-					regulator-always-on;
-				};
-
-				smps3_reg: smps3 {
-					/* VDD_GPU IVA DSPEVE */
-					regulator-name = "smps3";
-					regulator-min-microvolt = <850000>;
-					regulator-max-microvolt = <1250000>;
-					regulator-boot-on;
-					regulator-always-on;
-				};
-
-				smps4_reg: smps4 {
-					/* VDDS1V8 */
-					regulator-name = "smps4";
-					regulator-min-microvolt = <1800000>;
-					regulator-max-microvolt = <1800000>;
-					regulator-always-on;
-					regulator-boot-on;
-				};
-
-				smps5_reg: smps5 {
-					/* VDD_DDR */
-					regulator-name = "smps5";
-					regulator-min-microvolt = <1350000>;
-					regulator-max-microvolt = <1350000>;
-					regulator-boot-on;
-					regulator-always-on;
-				};
-
-				ldo1_reg: ldo1 {
-					/* LDO1_OUT --> SDIO  */
-					regulator-name = "ldo1";
-					regulator-min-microvolt = <1800000>;
-					regulator-max-microvolt = <3300000>;
-					regulator-always-on;
-					regulator-boot-on;
-					regulator-allow-bypass;
-				};
-
-				ldo2_reg: ldo2 {
-					/* LDO2_OUT --> TP1017 (UNUSED)  */
-					regulator-name = "ldo2";
-					regulator-min-microvolt = <1800000>;
-					regulator-max-microvolt = <3300000>;
-					regulator-allow-bypass;
-				};
-
-				ldo3_reg: ldo3 {
-					/* VDDA_1V8_PHY */
-					regulator-name = "ldo3";
-					regulator-min-microvolt = <1800000>;
-					regulator-max-microvolt = <1800000>;
-					regulator-boot-on;
-					regulator-always-on;
-				};
-
-				ldo5_reg: ldo5 {
-					/* VDDA_1V8_PLL */
-					regulator-name = "ldo5";
-					regulator-min-microvolt = <1800000>;
-					regulator-max-microvolt = <1800000>;
-					regulator-always-on;
-					regulator-boot-on;
-				};
-
-				ldo4_reg: ldo4 {
-					/* VDDA_3V_USB: VDDA_USBHS33 */
-					regulator-name = "ldo4";
-					regulator-min-microvolt = <3300000>;
-					regulator-max-microvolt = <3300000>;
-					regulator-boot-on;
-				};
-			};
-		};
-
-		tps65917_power_button {
-			compatible = "ti,palmas-pwrbutton";
-			interrupt-parent = <&tps65917>;
-			interrupts = <1 IRQ_TYPE_NONE>;
-			wakeup-source;
-			ti,palmas-long-press-seconds = <6>;
-		};
-	};
-
-	pcf_gpio_21: gpio@21 {
-		compatible = "ti,pcf8575";
-		reg = <0x21>;
-		lines-initial-states = <0x1408>;
-		gpio-controller;
-		#gpio-cells = <2>;
-		interrupt-parent = <&gpio6>;
-		interrupts = <11 IRQ_TYPE_EDGE_FALLING>;
-		interrupt-controller;
-		#interrupt-cells = <2>;
-	};
-
-	tlv320aic3106: tlv320aic3106@19 {
-		#sound-dai-cells = <0>;
-		compatible = "ti,tlv320aic3106";
-		reg = <0x19>;
-		adc-settle-ms = <40>;
-		ai3x-micbias-vg = <1>;		/* 2.0V */
-		status = "okay";
-
-		/* Regulators */
-		AVDD-supply = <&evm_3v3>;
-		IOVDD-supply = <&evm_3v3>;
-		DRVDD-supply = <&evm_3v3>;
-		DVDD-supply = <&aic_dvdd>;
+		regulator-allow-bypass;
 	};
 };
 
-&i2c5 {
-	status = "okay";
-	pinctrl-names = "default";
-	pinctrl-0 = <&i2c5_pins>;
-	clock-frequency = <400000>;
-
-	pcf_hdmi: pcf8575@26 {
-		compatible = "nxp,pcf8575";
-		reg = <0x26>;
-		gpio-controller;
-		#gpio-cells = <2>;
-		/*
-		 * initial state is used here to keep the mdio interface
-		 * selected on RU89 through SEL_VIN4_MUX_S0, VIN2_S1 and
-		 * VIN2_S0 driven high otherwise Ethernet stops working
-		 * VIN6_SEL_S0 is low, thus selecting McASP3 over VIN6
-		 */
-		lines-initial-states = <0x0f2b>;
-
-		p1 {
-			/* vin6_sel_s0: high: VIN6, low: audio */
-			gpio-hog;
-			gpios = <1 GPIO_ACTIVE_HIGH>;
-			output-low;
-			line-name = "vin6_sel_s0";
-		};
-	};
-};
-
-&uart1 {
-	status = "okay";
-	interrupts-extended = <&crossbar_mpu GIC_SPI 67 IRQ_TYPE_LEVEL_HIGH>,
-			      <&dra7_pmx_core 0x3e0>;
-};
-
-&elm {
-	status = "okay";
-};
-
-&gpmc {
-	status = "okay";
-	pinctrl-names = "default";
-	pinctrl-0 = <&nand_default>;
-	ranges = <0 0 0x08000000 0x01000000>;	/* minimum GPMC partition = 16MB */
-	nand@0,0 {
-		/* To use NAND, DIP switch SW5 must be set like so:
-		 * SW5.1 (NAND_SELn) = ON (LOW)
-		 * SW5.9 (GPMC_WPN) = OFF (HIGH)
-		 */
-		compatible = "ti,omap2-nand";
-		reg = <0 0 4>;		/* device IO registers */
-		interrupt-parent = <&gpmc>;
-		interrupts = <0 IRQ_TYPE_NONE>, /* fifoevent */
-			     <1 IRQ_TYPE_NONE>;	/* termcount */
-		ti,nand-ecc-opt = "bch8";
-		ti,elm-id = <&elm>;
-		nand-bus-width = <16>;
-		gpmc,device-width = <2>;
-		gpmc,sync-clk-ps = <0>;
-		gpmc,cs-on-ns = <0>;
-		gpmc,cs-rd-off-ns = <80>;
-		gpmc,cs-wr-off-ns = <80>;
-		gpmc,adv-on-ns = <0>;
-		gpmc,adv-rd-off-ns = <60>;
-		gpmc,adv-wr-off-ns = <60>;
-		gpmc,we-on-ns = <10>;
-		gpmc,we-off-ns = <50>;
-		gpmc,oe-on-ns = <4>;
-		gpmc,oe-off-ns = <40>;
-		gpmc,access-ns = <40>;
-		gpmc,wr-access-ns = <80>;
-		gpmc,rd-cycle-ns = <80>;
-		gpmc,wr-cycle-ns = <80>;
-		gpmc,bus-turnaround-ns = <0>;
-		gpmc,cycle2cycle-delay-ns = <0>;
-		gpmc,clk-activation-ns = <0>;
-		gpmc,wr-data-mux-bus-ns = <0>;
-		/* MTD partition table */
-		/* All SPL-* partitions are sized to minimal length
-		 * which can be independently programmable. For
-		 * NAND flash this is equal to size of erase-block */
-		#address-cells = <1>;
-		#size-cells = <1>;
-		partition@0 {
-			label = "NAND.SPL";
-			reg = <0x00000000 0x000020000>;
-		};
-		partition@1 {
-			label = "NAND.SPL.backup1";
-			reg = <0x00020000 0x00020000>;
-		};
-		partition@2 {
-			label = "NAND.SPL.backup2";
-			reg = <0x00040000 0x00020000>;
-		};
-		partition@3 {
-			label = "NAND.SPL.backup3";
-			reg = <0x00060000 0x00020000>;
-		};
-		partition@4 {
-			label = "NAND.u-boot-spl-os";
-			reg = <0x00080000 0x00040000>;
-		};
-		partition@5 {
-			label = "NAND.u-boot";
-			reg = <0x000c0000 0x00100000>;
-		};
-		partition@6 {
-			label = "NAND.u-boot-env";
-			reg = <0x001c0000 0x00020000>;
-		};
-		partition@7 {
-			label = "NAND.u-boot-env.backup1";
-			reg = <0x001e0000 0x00020000>;
-		};
-		partition@8 {
-			label = "NAND.kernel";
-			reg = <0x00200000 0x00800000>;
-		};
-		partition@9 {
-			label = "NAND.file-system";
-			reg = <0x00a00000 0x0f600000>;
-		};
-	};
-};
-
-&usb2_phy1 {
-	phy-supply = <&ldo4_reg>;
-};
-
-&usb2_phy2 {
-	phy-supply = <&ldo4_reg>;
-};
-
-&omap_dwc3_1 {
-	extcon = <&extcon_usb1>;
-};
-
-&omap_dwc3_2 {
-	extcon = <&extcon_usb2>;
-};
-
-&usb1 {
-	dr_mode = "peripheral";
-	pinctrl-names = "default";
-	pinctrl-0 = <&usb1_pins>;
-};
-
-&usb2 {
-	dr_mode = "host";
-	pinctrl-names = "default";
-	pinctrl-0 = <&usb2_pins>;
-};
-
-&mmc1 {
-	status = "okay";
-	pinctrl-names = "default";
-	pinctrl-0 = <&mmc1_pins_default>;
-	vmmc-supply = <&evm_3v3_sd>;
-	vmmc_aux-supply = <&ldo1_reg>;
-	bus-width = <4>;
-	/*
-	 * SDCD signal is not being used here - using the fact that GPIO mode
-	 * is a viable alternative
-	 */
-	cd-gpios = <&gpio6 27 GPIO_ACTIVE_LOW>;
-	max-frequency = <192000000>;
-};
-
-&mmc2 {
-	/* SW5-3 in ON position */
-	status = "okay";
-	pinctrl-names = "default";
-	pinctrl-0 = <&mmc2_pins_default>;
-
-	vmmc-supply = <&evm_3v3>;
-	bus-width = <8>;
-	ti,non-removable;
-	max-frequency = <192000000>;
+&hdmi {
+	vdda_video-supply = <&ldo5_reg>;
 };
 
-&dra7_pmx_core {
-	cpsw_default: cpsw_default {
-		pinctrl-single,pins = <
-			/* Slave 2 */
-			DRA7XX_CORE_IOPAD(0x3598, PIN_OUTPUT | MUX_MODE3)	/* vin2a_d12.rgmii1_txc */
-			DRA7XX_CORE_IOPAD(0x359c, PIN_OUTPUT | MUX_MODE3)	/* vin2a_d13.rgmii1_tctl */
-			DRA7XX_CORE_IOPAD(0x35a0, PIN_OUTPUT | MUX_MODE3)	/* vin2a_d14.rgmii1_td3 */
-			DRA7XX_CORE_IOPAD(0x35a4, PIN_OUTPUT | MUX_MODE3)	/* vin2a_d15.rgmii1_td2 */
-			DRA7XX_CORE_IOPAD(0x35a8, PIN_OUTPUT | MUX_MODE3)	/* vin2a_d16.rgmii1_td1 */
-			DRA7XX_CORE_IOPAD(0x35ac, PIN_OUTPUT | MUX_MODE3)	/* vin2a_d17.rgmii1_td0 */
-			DRA7XX_CORE_IOPAD(0x35b0, PIN_INPUT | MUX_MODE3)	/* vin2a_d18.rgmii1_rclk */
-			DRA7XX_CORE_IOPAD(0x35b4, PIN_INPUT | MUX_MODE3)	/* vin2a_d19.rgmii1_rctl */
-			DRA7XX_CORE_IOPAD(0x35b8, PIN_INPUT | MUX_MODE3)	/* vin2a_d20.rgmii1_rd3 */
-			DRA7XX_CORE_IOPAD(0x35bc, PIN_INPUT | MUX_MODE3)	/* vin2a_d21.rgmii1_rd2 */
-			DRA7XX_CORE_IOPAD(0x35c0, PIN_INPUT | MUX_MODE3)	/* vin2a_d22.rgmii1_rd1 */
-			DRA7XX_CORE_IOPAD(0x35c4, PIN_INPUT | MUX_MODE3)	/* vin2a_d23.rgmii1_rd0 */
-		>;
-
-	};
-
-	cpsw_sleep: cpsw_sleep {
-		pinctrl-single,pins = <
-			/* Slave 2 */
-			DRA7XX_CORE_IOPAD(0x3598, MUX_MODE15)
-			DRA7XX_CORE_IOPAD(0x359c, MUX_MODE15)
-			DRA7XX_CORE_IOPAD(0x35a0, MUX_MODE15)
-			DRA7XX_CORE_IOPAD(0x35a4, MUX_MODE15)
-			DRA7XX_CORE_IOPAD(0x35a8, MUX_MODE15)
-			DRA7XX_CORE_IOPAD(0x35ac, MUX_MODE15)
-			DRA7XX_CORE_IOPAD(0x35b0, MUX_MODE15)
-			DRA7XX_CORE_IOPAD(0x35b4, MUX_MODE15)
-			DRA7XX_CORE_IOPAD(0x35b8, MUX_MODE15)
-			DRA7XX_CORE_IOPAD(0x35bc, MUX_MODE15)
-			DRA7XX_CORE_IOPAD(0x35c0, MUX_MODE15)
-			DRA7XX_CORE_IOPAD(0x35c4, MUX_MODE15)
-		>;
-	};
-
-	davinci_mdio_default: davinci_mdio_default {
-		pinctrl-single,pins = <
-			/* MDIO */
-			DRA7XX_CORE_IOPAD(0x363c, PIN_OUTPUT_PULLUP | MUX_MODE0)	/* mdio_d.mdio_d */
-			DRA7XX_CORE_IOPAD(0x3640, PIN_INPUT_PULLUP | MUX_MODE0)	/* mdio_clk.mdio_clk */
-		>;
-	};
-
-	davinci_mdio_sleep: davinci_mdio_sleep {
-		pinctrl-single,pins = <
-			DRA7XX_CORE_IOPAD(0x363c, MUX_MODE15)
-			DRA7XX_CORE_IOPAD(0x3640, MUX_MODE15)
-		>;
-	};
+&pcf_gpio_21 {
+	interrupt-parent = <&gpio6>;
+	interrupts = <11 IRQ_TYPE_EDGE_FALLING>;
 };
 
 &mac {
-	status = "okay";
-	pinctrl-names = "default", "sleep";
-	pinctrl-0 = <&cpsw_default>;
-	pinctrl-1 = <&cpsw_sleep>;
 	slaves = <1>;
 	mode-gpios = <&pcf_gpio_21 4 GPIO_ACTIVE_HIGH>;
 };
@@ -697,158 +43,3 @@
 	phy_id = <&davinci_mdio>, <3>;
 	phy-mode = "rgmii";
 };
-
-&davinci_mdio {
-	pinctrl-names = "default", "sleep";
-	pinctrl-0 = <&davinci_mdio_default>;
-	pinctrl-1 = <&davinci_mdio_sleep>;
-};
-
-&dcan1 {
-	status = "ok";
-	pinctrl-names = "default", "sleep", "active";
-	pinctrl-0 = <&dcan1_pins_sleep>;
-	pinctrl-1 = <&dcan1_pins_sleep>;
-	pinctrl-2 = <&dcan1_pins_default>;
-};
-
-&qspi {
-	status = "okay";
-	pinctrl-names = "default";
-	pinctrl-0 = <&qspi1_pins>;
-
-	spi-max-frequency = <48000000>;
-	m25p80@0 {
-		compatible = "s25fl256s1";
-		spi-max-frequency = <48000000>;
-		reg = <0>;
-		spi-tx-bus-width = <1>;
-		spi-rx-bus-width = <4>;
-		spi-cpol;
-		spi-cpha;
-		#address-cells = <1>;
-		#size-cells = <1>;
-
-		/* MTD partition table.
-		 * The ROM checks the first four physical blocks
-		 * for a valid file to boot and the flash here is
-		 * 64KiB block size.
-		 */
-		partition@0 {
-			label = "QSPI.SPL";
-			reg = <0x00000000 0x000010000>;
-		};
-		partition@1 {
-			label = "QSPI.SPL.backup1";
-			reg = <0x00010000 0x00010000>;
-		};
-		partition@2 {
-			label = "QSPI.SPL.backup2";
-			reg = <0x00020000 0x00010000>;
-		};
-		partition@3 {
-			label = "QSPI.SPL.backup3";
-			reg = <0x00030000 0x00010000>;
-		};
-		partition@4 {
-			label = "QSPI.u-boot";
-			reg = <0x00040000 0x00100000>;
-		};
-		partition@5 {
-			label = "QSPI.u-boot-spl-os";
-			reg = <0x00140000 0x00080000>;
-		};
-		partition@6 {
-			label = "QSPI.u-boot-env";
-			reg = <0x001c0000 0x00010000>;
-		};
-		partition@7 {
-			label = "QSPI.u-boot-env.backup1";
-			reg = <0x001d0000 0x0010000>;
-		};
-		partition@8 {
-			label = "QSPI.kernel";
-			reg = <0x001e0000 0x0800000>;
-		};
-		partition@9 {
-			label = "QSPI.file-system";
-			reg = <0x009e0000 0x01620000>;
-		};
-	};
-};
-
-&dss {
-	status = "ok";
-
-	vdda_video-supply = <&ldo5_reg>;
-};
-
-&hdmi {
-	status = "ok";
-	vdda-supply = <&ldo3_reg>;
-
-	pinctrl-names = "default";
-	pinctrl-0 = <&hdmi_pins>;
-
-	port {
-		hdmi_out: endpoint {
-			remote-endpoint = <&tpd12s015_in>;
-		};
-	};
-};
-
-&atl {
-	pinctrl-names = "default";
-	pinctrl-0 = <&atl_pins>;
-
-	assigned-clocks = <&abe_dpll_sys_clk_mux>,
-			  <&atl_gfclk_mux>,
-			  <&dpll_abe_ck>,
-			  <&dpll_abe_m2x2_ck>,
-			  <&atl_clkin2_ck>;
-	assigned-clock-parents = <&sys_clkin2>, <&dpll_abe_m2_ck>;
-	assigned-clock-rates = <0>, <0>, <180633600>, <361267200>, <5644800>;
-
-	status = "okay";
-
-	atl2 {
-		bws = <DRA7_ATL_WS_MCASP2_FSX>;
-		aws = <DRA7_ATL_WS_MCASP3_FSX>;
-	};
-};
-
-&mcasp3 {
-	#sound-dai-cells = <0>;
-	pinctrl-names = "default", "sleep";
-	pinctrl-0 = <&mcasp3_pins>;
-	pinctrl-1 = <&mcasp3_sleep_pins>;
-
-	assigned-clocks = <&mcasp3_ahclkx_mux>;
-	assigned-clock-parents = <&atl_clkin2_ck>;
-
-	status = "okay";
-
-	op-mode = <0>;          /* MCASP_IIS_MODE */
-	tdm-slots = <2>;
-	/* 4 serializer */
-	serial-dir = <  /* 0: INACTIVE, 1: TX, 2: RX */
-		1 2 0 0
-	>;
-};
-
-&mailbox5 {
-	status = "okay";
-	mbox_ipu1_ipc3x: mbox_ipu1_ipc3x {
-		status = "okay";
-	};
-	mbox_dsp1_ipc3x: mbox_dsp1_ipc3x {
-		status = "okay";
-	};
-};
-
-&mailbox6 {
-	status = "okay";
-	mbox_ipu2_ipc3x: mbox_ipu2_ipc3x {
-		status = "okay";
-	};
-};
-- 
2.8.0.rc3