From: <c_traja@qti.qualcomm.com> To: <ath10k@lists.infradead.org> Cc: <linux-wireless@vger.kernel.org>, <tamizhchelvam@codeaurora.org>, "Tamizh chelvam" <c_traja@qti.qualcomm.com>, <stable@vger.kernel.org> Subject: [PATCHv3] ath10k: fix boot failure in UTF mode/testmode Date: Tue, 31 Jan 2017 10:26:09 +0530 [thread overview] Message-ID: <1485838569-1027-1-git-send-email-c_traja@qti.qualcomm.com> (raw) From: Tamizh chelvam <c_traja@qti.qualcomm.com> Rx filter reset and the dynamic tx switch mode (EXT_RESOURCE_CFG) configuration are causing the following errors when UTF firmware is loaded to the target. Error message 1: [ 598.015629] ath10k_pci 0001:01:00.0: failed to ping firmware: -110 [ 598.020828] ath10k_pci 0001:01:00.0: failed to reset rx filter: -110 [ 598.141556] ath10k_pci 0001:01:00.0: failed to start core (testmode): -110 Error message 2: [ 668.615839] ath10k_ahb a000000.wifi: failed to send ext resource cfg command : -95 [ 668.618902] ath10k_ahb a000000.wifi: failed to start core (testmode): -95 Avoiding these configurations while bringing the target in testmode is solving the problem. Cc: stable@vger.kernel.org Signed-off-by: Tamizh chelvam <c_traja@qti.qualcomm.com> --- v3: *Added Cc:stable@vger.kernel.org in commit log drivers/net/wireless/ath/ath10k/core.c | 14 +++++++++----- 1 file changed, 9 insertions(+), 5 deletions(-) diff --git a/drivers/net/wireless/ath/ath10k/core.c b/drivers/net/wireless/ath/ath10k/core.c index c2afcca..c27e7ea 100644 --- a/drivers/net/wireless/ath/ath10k/core.c +++ b/drivers/net/wireless/ath/ath10k/core.c @@ -1996,7 +1996,8 @@ int ath10k_core_start(struct ath10k *ar, enum ath10k_firmware_mode mode, ath10k_dbg(ar, ATH10K_DBG_BOOT, "firmware %s booted\n", ar->hw->wiphy->fw_version); - if (test_bit(WMI_SERVICE_EXT_RES_CFG_SUPPORT, ar->wmi.svc_map)) { + if (test_bit(WMI_SERVICE_EXT_RES_CFG_SUPPORT, ar->wmi.svc_map) && + mode == ATH10K_FIRMWARE_MODE_NORMAL) { val = 0; if (ath10k_peer_stats_enabled(ar)) val = WMI_10_4_PEER_STATS; @@ -2049,10 +2050,13 @@ int ath10k_core_start(struct ath10k *ar, enum ath10k_firmware_mode mode, * possible to implicitly make it correct by creating a dummy vdev and * then deleting it. */ - status = ath10k_core_reset_rx_filter(ar); - if (status) { - ath10k_err(ar, "failed to reset rx filter: %d\n", status); - goto err_hif_stop; + if (mode == ATH10K_FIRMWARE_MODE_NORMAL) { + status = ath10k_core_reset_rx_filter(ar); + if (status) { + ath10k_err(ar, + "failed to reset rx filter: %d\n", status); + goto err_hif_stop; + } } /* If firmware indicates Full Rx Reorder support it must be used in a -- 1.7.9.5
WARNING: multiple messages have this Message-ID (diff)
From: <c_traja@qti.qualcomm.com> To: ath10k@lists.infradead.org Cc: Tamizh chelvam <c_traja@qti.qualcomm.com>, tamizhchelvam@codeaurora.org, linux-wireless@vger.kernel.org, stable@vger.kernel.org Subject: [PATCHv3] ath10k: fix boot failure in UTF mode/testmode Date: Tue, 31 Jan 2017 10:26:09 +0530 [thread overview] Message-ID: <1485838569-1027-1-git-send-email-c_traja@qti.qualcomm.com> (raw) From: Tamizh chelvam <c_traja@qti.qualcomm.com> Rx filter reset and the dynamic tx switch mode (EXT_RESOURCE_CFG) configuration are causing the following errors when UTF firmware is loaded to the target. Error message 1: [ 598.015629] ath10k_pci 0001:01:00.0: failed to ping firmware: -110 [ 598.020828] ath10k_pci 0001:01:00.0: failed to reset rx filter: -110 [ 598.141556] ath10k_pci 0001:01:00.0: failed to start core (testmode): -110 Error message 2: [ 668.615839] ath10k_ahb a000000.wifi: failed to send ext resource cfg command : -95 [ 668.618902] ath10k_ahb a000000.wifi: failed to start core (testmode): -95 Avoiding these configurations while bringing the target in testmode is solving the problem. Cc: stable@vger.kernel.org Signed-off-by: Tamizh chelvam <c_traja@qti.qualcomm.com> --- v3: *Added Cc:stable@vger.kernel.org in commit log drivers/net/wireless/ath/ath10k/core.c | 14 +++++++++----- 1 file changed, 9 insertions(+), 5 deletions(-) diff --git a/drivers/net/wireless/ath/ath10k/core.c b/drivers/net/wireless/ath/ath10k/core.c index c2afcca..c27e7ea 100644 --- a/drivers/net/wireless/ath/ath10k/core.c +++ b/drivers/net/wireless/ath/ath10k/core.c @@ -1996,7 +1996,8 @@ int ath10k_core_start(struct ath10k *ar, enum ath10k_firmware_mode mode, ath10k_dbg(ar, ATH10K_DBG_BOOT, "firmware %s booted\n", ar->hw->wiphy->fw_version); - if (test_bit(WMI_SERVICE_EXT_RES_CFG_SUPPORT, ar->wmi.svc_map)) { + if (test_bit(WMI_SERVICE_EXT_RES_CFG_SUPPORT, ar->wmi.svc_map) && + mode == ATH10K_FIRMWARE_MODE_NORMAL) { val = 0; if (ath10k_peer_stats_enabled(ar)) val = WMI_10_4_PEER_STATS; @@ -2049,10 +2050,13 @@ int ath10k_core_start(struct ath10k *ar, enum ath10k_firmware_mode mode, * possible to implicitly make it correct by creating a dummy vdev and * then deleting it. */ - status = ath10k_core_reset_rx_filter(ar); - if (status) { - ath10k_err(ar, "failed to reset rx filter: %d\n", status); - goto err_hif_stop; + if (mode == ATH10K_FIRMWARE_MODE_NORMAL) { + status = ath10k_core_reset_rx_filter(ar); + if (status) { + ath10k_err(ar, + "failed to reset rx filter: %d\n", status); + goto err_hif_stop; + } } /* If firmware indicates Full Rx Reorder support it must be used in a -- 1.7.9.5 _______________________________________________ ath10k mailing list ath10k@lists.infradead.org http://lists.infradead.org/mailman/listinfo/ath10k
next reply other threads:[~2017-01-31 4:59 UTC|newest] Thread overview: 4+ messages / expand[flat|nested] mbox.gz Atom feed top 2017-01-31 4:56 c_traja [this message] 2017-01-31 4:56 ` [PATCHv3] ath10k: fix boot failure in UTF mode/testmode c_traja 2017-02-07 8:52 ` Kalle Valo 2017-02-07 8:52 ` Kalle Valo
Reply instructions: You may reply publicly to this message via plain-text email using any one of the following methods: * Save the following mbox file, import it into your mail client, and reply-to-all from there: mbox Avoid top-posting and favor interleaved quoting: https://en.wikipedia.org/wiki/Posting_style#Interleaved_style * Reply using the --to, --cc, and --in-reply-to switches of git-send-email(1): git send-email \ --in-reply-to=1485838569-1027-1-git-send-email-c_traja@qti.qualcomm.com \ --to=c_traja@qti.qualcomm.com \ --cc=ath10k@lists.infradead.org \ --cc=linux-wireless@vger.kernel.org \ --cc=stable@vger.kernel.org \ --cc=tamizhchelvam@codeaurora.org \ /path/to/YOUR_REPLY https://kernel.org/pub/software/scm/git/docs/git-send-email.html * If your mail client supports setting the In-Reply-To header via mailto: links, try the mailto: linkBe sure your reply has a Subject: header at the top and a blank line before the message body.
This is an external index of several public inboxes, see mirroring instructions on how to clone and mirror all data and code used by this external index.