[PATCHv5 2/2] clk: keystone: Add sci-clk driver support

[Tero Kristo <t-kristo@ti.com>]

In K2G, the clock handling is done through firmware executing on a
separate core. Linux kernel needs to communicate to the firmware
through TI system control interface to access any power management
related resources, including clocks.

The keystone sci-clk driver does this, by communicating to the
firmware through the TI SCI driver. The driver adds support for
registering clocks through DT, and basic required clock operations
like prepare/get_rate, etc.

Signed-off-by: Tero Kristo <t-kristo@ti.com>
---
Just sending out patch #2 of the series, patch #1 is the same from v4.

Changes in v5:
 - moved the sci_clk_data->clocks array under the provider
 - enforced const type on sci_clk_data

 MAINTAINERS                    |   1 +
 drivers/clk/Kconfig            |   8 +-
 drivers/clk/Makefile           |   2 +-
 drivers/clk/keystone/Kconfig   |  15 +
 drivers/clk/keystone/Makefile  |   3 +-
 drivers/clk/keystone/sci-clk.c | 724 +++++++++++++++++++++++++++++++++++++++++
 6 files changed, 744 insertions(+), 9 deletions(-)
 create mode 100644 drivers/clk/keystone/Kconfig
 create mode 100644 drivers/clk/keystone/sci-clk.c

diff --git a/MAINTAINERS b/MAINTAINERS
index 880a23d..1ba72e6 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -12631,6 +12631,7 @@ F:	Documentation/devicetree/bindings/soc/ti/sci-pm-domain.txt
 F:	include/dt-bindings/genpd/k2g.h
 F:	drivers/soc/ti/ti_sci_pm_domains.c
 F:	Documentation/devicetree/bindings/clock/ti,sci-clk.txt
+F:	drivers/clk/keystone/sci-clk.c
 
 THANKO'S RAREMONO AM/FM/SW RADIO RECEIVER USB DRIVER
 M:	Hans Verkuil <hverkuil@xs4all.nl>
diff --git a/drivers/clk/Kconfig b/drivers/clk/Kconfig
index 36cfea3..10fef77 100644
--- a/drivers/clk/Kconfig
+++ b/drivers/clk/Kconfig
@@ -164,13 +164,6 @@ config COMMON_CLK_XGENE
 	---help---
 	  Sypport for the APM X-Gene SoC reference, PLL, and device clocks.
 
-config COMMON_CLK_KEYSTONE
-	tristate "Clock drivers for Keystone based SOCs"
-	depends on (ARCH_KEYSTONE || COMPILE_TEST) && OF
-	---help---
-          Supports clock drivers for Keystone based SOCs. These SOCs have local
-	  a power sleep control module that gate the clock to the IPs and PLLs.
-
 config COMMON_CLK_NXP
 	def_bool COMMON_CLK && (ARCH_LPC18XX || ARCH_LPC32XX)
 	select REGMAP_MMIO if ARCH_LPC32XX
@@ -219,6 +212,7 @@ config COMMON_CLK_VC5
 
 source "drivers/clk/bcm/Kconfig"
 source "drivers/clk/hisilicon/Kconfig"
+source "drivers/clk/keystone/Kconfig"
 source "drivers/clk/mediatek/Kconfig"
 source "drivers/clk/meson/Kconfig"
 source "drivers/clk/mvebu/Kconfig"
diff --git a/drivers/clk/Makefile b/drivers/clk/Makefile
index c19983a..40694e6 100644
--- a/drivers/clk/Makefile
+++ b/drivers/clk/Makefile
@@ -61,7 +61,7 @@ obj-$(CONFIG_H8300)			+= h8300/
 obj-$(CONFIG_ARCH_HISI)			+= hisilicon/
 obj-$(CONFIG_ARCH_MXC)			+= imx/
 obj-$(CONFIG_MACH_INGENIC)		+= ingenic/
-obj-$(CONFIG_COMMON_CLK_KEYSTONE)	+= keystone/
+obj-$(CONFIG_ARCH_KEYSTONE)		+= keystone/
 obj-$(CONFIG_MACH_LOONGSON32)		+= loongson1/
 obj-$(CONFIG_ARCH_MEDIATEK)		+= mediatek/
 obj-$(CONFIG_COMMON_CLK_AMLOGIC)	+= meson/
diff --git a/drivers/clk/keystone/Kconfig b/drivers/clk/keystone/Kconfig
new file mode 100644
index 0000000..1fea328
--- /dev/null
+++ b/drivers/clk/keystone/Kconfig
@@ -0,0 +1,15 @@
+config COMMON_CLK_KEYSTONE
+	tristate "Clock drivers for Keystone based SOCs"
+	depends on (ARCH_KEYSTONE || COMPILE_TEST) && OF
+	---help---
+	  Supports clock drivers for Keystone based SOCs. These SOCs have local
+	  a power sleep control module that gate the clock to the IPs and PLLs.
+
+config TI_SCI_CLK
+	tristate "TI System Control Interface clock drivers"
+	depends on (ARCH_KEYSTONE || COMPILE_TEST) && OF
+	default TI_SCI_PROTOCOL
+	---help---
+	  This adds the clock driver support over TI System Control Interface.
+	  If you wish to use clock resources from the PMMC firmware, say Y.
+	  Otherwise, say N.
diff --git a/drivers/clk/keystone/Makefile b/drivers/clk/keystone/Makefile
index 0477cf6..c125939 100644
--- a/drivers/clk/keystone/Makefile
+++ b/drivers/clk/keystone/Makefile
@@ -1 +1,2 @@
-obj-y			+= pll.o gate.o
+obj-$(CONFIG_COMMON_CLK_KEYSTONE)	+= pll.o gate.o
+obj-$(CONFIG_TI_SCI_CLK)		+= sci-clk.o
diff --git a/drivers/clk/keystone/sci-clk.c b/drivers/clk/keystone/sci-clk.c
new file mode 100644
index 0000000..fc9ce6b
--- /dev/null
+++ b/drivers/clk/keystone/sci-clk.c
@@ -0,0 +1,724 @@
+/*
+ * SCI Clock driver for keystone based devices
+ *
+ * Copyright (C) 2015-2016 Texas Instruments Incorporated - http://www.ti.com/
+ *	Tero Kristo <t-kristo@ti.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ * This program is distributed "as is" WITHOUT ANY WARRANTY of any
+ * kind, whether express or implied; without even the implied warranty
+ * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ */
+#include <linux/clk-provider.h>
+#include <linux/err.h>
+#include <linux/io.h>
+#include <linux/module.h>
+#include <linux/of_address.h>
+#include <linux/of_device.h>
+#include <linux/platform_device.h>
+#include <linux/slab.h>
+#include <linux/soc/ti/ti_sci_protocol.h>
+
+#define SCI_CLK_SSC_ENABLE		BIT(0)
+#define SCI_CLK_ALLOW_FREQ_CHANGE	BIT(1)
+#define SCI_CLK_INPUT_TERMINATION	BIT(2)
+
+/**
+ * struct sci_clk_data - TI SCI clock data
+ * @dev: device index
+ * @num_clks: number of clocks for this device
+ */
+struct sci_clk_data {
+	u16 dev;
+	u16 num_clks;
+};
+
+/**
+ * struct sci_clk_provider - TI SCI clock provider representation
+ * @sci: Handle to the System Control Interface protocol handler
+ * @ops: Pointer to the SCI ops to be used by the clocks
+ * @dev: Device pointer for the clock provider
+ * @clk_data: Clock data
+ * @clocks: Clocks array for this device
+ */
+struct sci_clk_provider {
+	const struct ti_sci_handle *sci;
+	const struct ti_sci_clk_ops *ops;
+	struct device *dev;
+	const struct sci_clk_data *clk_data;
+	struct clk_hw **clocks;
+};
+
+/**
+ * struct sci_clk - TI SCI clock representation
+ * @hw:		 Hardware clock cookie for common clock framework
+ * @dev_id:	 Device index
+ * @clk_id:	 Clock index
+ * @node:	 Clocks list link
+ * @provider:	 Master clock provider
+ * @flags:	 Flags for the clock
+ */
+struct sci_clk {
+	struct clk_hw hw;
+	u16 dev_id;
+	u8 clk_id;
+	struct list_head node;
+	struct sci_clk_provider *provider;
+	u8 flags;
+};
+
+#define to_sci_clk(_hw) container_of(_hw, struct sci_clk, hw)
+
+/**
+ * sci_clk_prepare - Prepare (enable) a TI SCI clock
+ * @hw: clock to prepare
+ *
+ * Prepares a clock to be actively used. Returns the SCI protocol status.
+ */
+static int sci_clk_prepare(struct clk_hw *hw)
+{
+	struct sci_clk *clk = to_sci_clk(hw);
+	bool enable_ssc = clk->flags & SCI_CLK_SSC_ENABLE;
+	bool allow_freq_change = clk->flags & SCI_CLK_ALLOW_FREQ_CHANGE;
+	bool input_termination = clk->flags & SCI_CLK_INPUT_TERMINATION;
+
+	return clk->provider->ops->get_clock(clk->provider->sci, clk->dev_id,
+					     clk->clk_id, enable_ssc,
+					     allow_freq_change,
+					     input_termination);
+}
+
+/**
+ * sci_clk_unprepare - Un-prepares (disables) a TI SCI clock
+ * @hw: clock to unprepare
+ *
+ * Un-prepares a clock from active state.
+ */
+static void sci_clk_unprepare(struct clk_hw *hw)
+{
+	struct sci_clk *clk = to_sci_clk(hw);
+	int ret;
+
+	ret = clk->provider->ops->put_clock(clk->provider->sci, clk->dev_id,
+					    clk->clk_id);
+	if (ret)
+		dev_err(clk->provider->dev,
+			"unprepare failed for dev=%d, clk=%d, ret=%d\n",
+			clk->dev_id, clk->clk_id, ret);
+}
+
+/**
+ * sci_clk_is_prepared - Check if a TI SCI clock is prepared or not
+ * @hw: clock to check status for
+ *
+ * Checks if a clock is prepared (enabled) in hardware. Returns non-zero
+ * value if clock is enabled, zero otherwise.
+ */
+static int sci_clk_is_prepared(struct clk_hw *hw)
+{
+	struct sci_clk *clk = to_sci_clk(hw);
+	bool req_state, current_state;
+	int ret;
+
+	ret = clk->provider->ops->is_on(clk->provider->sci, clk->dev_id,
+					clk->clk_id, &req_state,
+					&current_state);
+	if (ret) {
+		dev_err(clk->provider->dev,
+			"is_prepared failed for dev=%d, clk=%d, ret=%d\n",
+			clk->dev_id, clk->clk_id, ret);
+		return 0;
+	}
+
+	return req_state;
+}
+
+/**
+ * sci_clk_recalc_rate - Get clock rate for a TI SCI clock
+ * @hw: clock to get rate for
+ * @parent_rate: parent rate provided by common clock framework, not used
+ *
+ * Gets the current clock rate of a TI SCI clock. Returns the current
+ * clock rate, or zero in failure.
+ */
+static unsigned long sci_clk_recalc_rate(struct clk_hw *hw,
+					 unsigned long parent_rate)
+{
+	struct sci_clk *clk = to_sci_clk(hw);
+	u64 freq;
+	int ret;
+
+	ret = clk->provider->ops->get_freq(clk->provider->sci, clk->dev_id,
+					   clk->clk_id, &freq);
+	if (ret) {
+		dev_err(clk->provider->dev,
+			"recalc-rate failed for dev=%d, clk=%d, ret=%d\n",
+			clk->dev_id, clk->clk_id, ret);
+		return 0;
+	}
+
+	return freq;
+}
+
+/**
+ * sci_clk_determine_rate - Determines a clock rate a clock can be set to
+ * @hw: clock to change rate for
+ * @req: requested rate configuration for the clock
+ *
+ * Determines a suitable clock rate and parent for a TI SCI clock.
+ * The parent handling is un-used, as generally the parent clock rates
+ * are not known by the kernel; instead these are internally handled
+ * by the firmware. Returns 0 on success, negative error value on failure.
+ */
+static int sci_clk_determine_rate(struct clk_hw *hw,
+				  struct clk_rate_request *req)
+{
+	struct sci_clk *clk = to_sci_clk(hw);
+	int ret;
+	u64 new_rate;
+
+	ret = clk->provider->ops->get_best_match_freq(clk->provider->sci,
+						      clk->dev_id,
+						      clk->clk_id,
+						      req->min_rate,
+						      req->rate,
+						      req->max_rate,
+						      &new_rate);
+	if (ret) {
+		dev_err(clk->provider->dev,
+			"determine-rate failed for dev=%d, clk=%d, ret=%d\n",
+			clk->dev_id, clk->clk_id, ret);
+		return ret;
+	}
+
+	req->rate = new_rate;
+
+	return 0;
+}
+
+/**
+ * sci_clk_set_rate - Set rate for a TI SCI clock
+ * @hw: clock to change rate for
+ * @rate: target rate for the clock
+ * @parent_rate: rate of the clock parent, not used for TI SCI clocks
+ *
+ * Sets a clock frequency for a TI SCI clock. Returns the TI SCI
+ * protocol status.
+ */
+static int sci_clk_set_rate(struct clk_hw *hw, unsigned long rate,
+			    unsigned long parent_rate)
+{
+	struct sci_clk *clk = to_sci_clk(hw);
+
+	return clk->provider->ops->set_freq(clk->provider->sci, clk->dev_id,
+					    clk->clk_id, rate, rate, rate);
+}
+
+/**
+ * sci_clk_get_parent - Get the current parent of a TI SCI clock
+ * @hw: clock to get parent for
+ *
+ * Returns the index of the currently selected parent for a TI SCI clock.
+ */
+static u8 sci_clk_get_parent(struct clk_hw *hw)
+{
+	struct sci_clk *clk = to_sci_clk(hw);
+	u8 parent_id;
+	int ret;
+
+	ret = clk->provider->ops->get_parent(clk->provider->sci, clk->dev_id,
+					     clk->clk_id, &parent_id);
+	if (ret) {
+		dev_err(clk->provider->dev,
+			"get-parent failed for dev=%d, clk=%d, ret=%d\n",
+			clk->dev_id, clk->clk_id, ret);
+		return 0;
+	}
+
+	return parent_id - clk->clk_id - 1;
+}
+
+/**
+ * sci_clk_set_parent - Set the parent of a TI SCI clock
+ * @hw: clock to set parent for
+ * @index: new parent index for the clock
+ *
+ * Sets the parent of a TI SCI clock. Return TI SCI protocol status.
+ */
+static int sci_clk_set_parent(struct clk_hw *hw, u8 index)
+{
+	struct sci_clk *clk = to_sci_clk(hw);
+
+	return clk->provider->ops->set_parent(clk->provider->sci, clk->dev_id,
+					      clk->clk_id,
+					      index + 1 + clk->clk_id);
+}
+
+static const struct clk_ops sci_clk_ops = {
+	.prepare = sci_clk_prepare,
+	.unprepare = sci_clk_unprepare,
+	.is_prepared = sci_clk_is_prepared,
+	.recalc_rate = sci_clk_recalc_rate,
+	.determine_rate = sci_clk_determine_rate,
+	.set_rate = sci_clk_set_rate,
+	.get_parent = sci_clk_get_parent,
+	.set_parent = sci_clk_set_parent,
+};
+
+/**
+ * _sci_clk_get - Gets a handle for an SCI clock
+ * @provider: Handle to SCI clock provider
+ * @dev_id: device ID for the clock to register
+ * @clk_id: clock ID for the clock to register
+ *
+ * Gets a handle to an existing TI SCI hw clock, or builds a new clock
+ * entry and registers it with the common clock framework. Called from
+ * the common clock framework, when a corresponding of_clk_get call is
+ * executed, or recursively from itself when parsing parent clocks.
+ * Returns a pointer to the hw clock struct, or ERR_PTR value in failure.
+ */
+static struct clk_hw *_sci_clk_build(struct sci_clk_provider *provider,
+				     u16 dev_id, u8 clk_id)
+{
+	struct clk_init_data init = { NULL };
+	struct sci_clk *sci_clk = NULL;
+	char *name = NULL;
+	char **parent_names = NULL;
+	int i;
+	int ret;
+
+	sci_clk = devm_kzalloc(provider->dev, sizeof(*sci_clk), GFP_KERNEL);
+	if (!sci_clk)
+		return ERR_PTR(-ENOMEM);
+
+	sci_clk->dev_id = dev_id;
+	sci_clk->clk_id = clk_id;
+	sci_clk->provider = provider;
+
+	ret = provider->ops->get_num_parents(provider->sci, dev_id,
+					     clk_id,
+					     &init.num_parents);
+	if (ret)
+		goto err;
+
+	name = kasprintf(GFP_KERNEL, "%s:%d:%d", dev_name(provider->dev),
+			 sci_clk->dev_id, sci_clk->clk_id);
+
+	init.name = name;
+
+	/*
+	 * From kernel point of view, we only care about a clocks parents,
+	 * if it has more than 1 possible parent. In this case, it is going
+	 * to have mux functionality. Otherwise it is going to act as a root
+	 * clock.
+	 */
+	if (init.num_parents < 2)
+		init.num_parents = 0;
+
+	if (init.num_parents) {
+		parent_names = kcalloc(init.num_parents, sizeof(char *),
+				       GFP_KERNEL);
+
+		if (!parent_names) {
+			ret = -ENOMEM;
+			goto err;
+		}
+
+		for (i = 0; i < init.num_parents; i++) {
+			char *parent_name;
+
+			parent_name = kasprintf(GFP_KERNEL, "%s:%d:%d",
+						dev_name(provider->dev),
+						sci_clk->dev_id,
+						sci_clk->clk_id + 1 + i);
+			if (!parent_name) {
+				ret = -ENOMEM;
+				goto err;
+			}
+			parent_names[i] = parent_name;
+		}
+		init.parent_names = (void *)parent_names;
+	}
+
+	init.ops = &sci_clk_ops;
+	sci_clk->hw.init = &init;
+
+	ret = devm_clk_hw_register(provider->dev, &sci_clk->hw);
+	if (ret)
+		dev_err(provider->dev, "failed clk register with %d\n", ret);
+
+err:
+	if (parent_names) {
+		for (i = 0; i < init.num_parents; i++)
+			kfree(parent_names[i]);
+
+		kfree(parent_names);
+	}
+
+	kfree(name);
+
+	if (ret)
+		return ERR_PTR(ret);
+
+	return &sci_clk->hw;
+}
+
+/**
+ * sci_clk_get - Xlate function for getting clock handles
+ * @clkspec: device tree clock specifier
+ * @data: pointer to the clock provider
+ *
+ * Xlate function for retrieving clock TI SCI hw clock handles based on
+ * device tree clock specifier. Called from the common clock framework,
+ * when a corresponding of_clk_get call is executed. Returns a pointer
+ * to the TI SCI hw clock struct, or ERR_PTR value in failure.
+ */
+static struct clk_hw *sci_clk_get(struct of_phandle_args *clkspec, void *data)
+{
+	struct sci_clk_provider *provider = data;
+	u16 dev_id;
+	u8 clk_id;
+	const struct sci_clk_data *clks = provider->clk_data;
+	struct clk_hw **clocks = provider->clocks;
+
+	if (clkspec->args_count != 2)
+		return ERR_PTR(-EINVAL);
+
+	dev_id = clkspec->args[0];
+	clk_id = clkspec->args[1];
+
+	while (clks->num_clks) {
+		if (clks->dev == dev_id) {
+			if (clk_id >= clks->num_clks)
+				return ERR_PTR(-EINVAL);
+
+			return clocks[clk_id];
+		}
+
+		clks++;
+	}
+
+	return ERR_PTR(-ENODEV);
+}
+
+int ti_sci_init_clocks(struct sci_clk_provider *p)
+{
+	const struct sci_clk_data *data = p->clk_data;
+	struct clk_hw *hw;
+	int i;
+
+	while (data->num_clks) {
+		p->clocks = devm_kcalloc(p->dev, data->num_clks,
+					 sizeof(struct sci_clk),
+					 GFP_KERNEL);
+		if (!p->clocks)
+			return -ENOMEM;
+
+		for (i = 0; i < data->num_clks; i++) {
+			hw = _sci_clk_build(p, data->dev, i);
+			if (!IS_ERR(hw)) {
+				p->clocks[i] = hw;
+				continue;
+			}
+
+			/* Skip any holes in the clock lists */
+			if (PTR_ERR(hw) == -ENODEV)
+				continue;
+
+			return PTR_ERR(hw);
+		}
+		data++;
+	}
+
+	return 0;
+}
+
+static const struct sci_clk_data k2g_clk_data[] = {
+	/* pmmc */
+	{ .dev = 0x0, .num_clks = 4 },
+
+	/* mlb0 */
+	{ .dev = 0x1, .num_clks = 5 },
+
+	/* dss0 */
+	{ .dev = 0x2, .num_clks = 2 },
+
+	/* mcbsp0 */
+	{ .dev = 0x3, .num_clks = 8 },
+
+	/* mcasp0 */
+	{ .dev = 0x4, .num_clks = 8 },
+
+	/* mcasp1 */
+	{ .dev = 0x5, .num_clks = 8 },
+
+	/* mcasp2 */
+	{ .dev = 0x6, .num_clks = 8 },
+
+	/* dcan0 */
+	{ .dev = 0x8, .num_clks = 2 },
+
+	/* dcan1 */
+	{ .dev = 0x9, .num_clks = 2 },
+
+	/* emif0 */
+	{ .dev = 0xa, .num_clks = 6 },
+
+	/* mmchs0 */
+	{ .dev = 0xb, .num_clks = 3 },
+
+	/* mmchs1 */
+	{ .dev = 0xc, .num_clks = 3 },
+
+	/* gpmc0 */
+	{ .dev = 0xd, .num_clks = 1 },
+
+	/* elm0 */
+	{ .dev = 0xe, .num_clks = 1 },
+
+	/* spi0 */
+	{ .dev = 0x10, .num_clks = 1 },
+
+	/* spi1 */
+	{ .dev = 0x11, .num_clks = 1 },
+
+	/* spi2 */
+	{ .dev = 0x12, .num_clks = 1 },
+
+	/* spi3 */
+	{ .dev = 0x13, .num_clks = 1 },
+
+	/* icss0 */
+	{ .dev = 0x14, .num_clks = 6 },
+
+	/* icss1 */
+	{ .dev = 0x15, .num_clks = 6 },
+
+	/* usb0 */
+	{ .dev = 0x16, .num_clks = 7 },
+
+	/* usb1 */
+	{ .dev = 0x17, .num_clks = 7 },
+
+	/* nss0 */
+	{ .dev = 0x18, .num_clks = 14 },
+
+	/* pcie0 */
+	{ .dev = 0x19, .num_clks = 1 },
+
+	/* gpio0 */
+	{ .dev = 0x1b, .num_clks = 1 },
+
+	/* gpio1 */
+	{ .dev = 0x1c, .num_clks = 1 },
+
+	/* timer64_0 */
+	{ .dev = 0x1d, .num_clks = 9 },
+
+	/* timer64_1 */
+	{ .dev = 0x1e, .num_clks = 9 },
+
+	/* timer64_2 */
+	{ .dev = 0x1f, .num_clks = 9 },
+
+	/* timer64_3 */
+	{ .dev = 0x20, .num_clks = 9 },
+
+	/* timer64_4 */
+	{ .dev = 0x21, .num_clks = 9 },
+
+	/* timer64_5 */
+	{ .dev = 0x22, .num_clks = 9 },
+
+	/* timer64_6 */
+	{ .dev = 0x23, .num_clks = 9 },
+
+	/* msgmgr0 */
+	{ .dev = 0x25, .num_clks = 1 },
+
+	/* bootcfg0 */
+	{ .dev = 0x26, .num_clks = 1 },
+
+	/* arm_bootrom0 */
+	{ .dev = 0x27, .num_clks = 1 },
+
+	/* dsp_bootrom0 */
+	{ .dev = 0x29, .num_clks = 1 },
+
+	/* debugss0 */
+	{ .dev = 0x2b, .num_clks = 8 },
+
+	/* uart0 */
+	{ .dev = 0x2c, .num_clks = 1 },
+
+	/* uart1 */
+	{ .dev = 0x2d, .num_clks = 1 },
+
+	/* uart2 */
+	{ .dev = 0x2e, .num_clks = 1 },
+
+	/* ehrpwm0 */
+	{ .dev = 0x2f, .num_clks = 1 },
+
+	/* ehrpwm1 */
+	{ .dev = 0x30, .num_clks = 1 },
+
+	/* ehrpwm2 */
+	{ .dev = 0x31, .num_clks = 1 },
+
+	/* ehrpwm3 */
+	{ .dev = 0x32, .num_clks = 1 },
+
+	/* ehrpwm4 */
+	{ .dev = 0x33, .num_clks = 1 },
+
+	/* ehrpwm5 */
+	{ .dev = 0x34, .num_clks = 1 },
+
+	/* eqep0 */
+	{ .dev = 0x35, .num_clks = 1 },
+
+	/* eqep1 */
+	{ .dev = 0x36, .num_clks = 1 },
+
+	/* eqep2 */
+	{ .dev = 0x37, .num_clks = 1 },
+
+	/* ecap0 */
+	{ .dev = 0x38, .num_clks = 1 },
+
+	/* ecap1 */
+	{ .dev = 0x39, .num_clks = 1 },
+
+	/* i2c0 */
+	{ .dev = 0x3a, .num_clks = 1 },
+
+	/* i2c1 */
+	{ .dev = 0x3b, .num_clks = 1 },
+
+	/* i2c2 */
+	{ .dev = 0x3c, .num_clks = 1 },
+
+	/* edma0 */
+	{ .dev = 0x3f, .num_clks = 2 },
+
+	/* semaphore0 */
+	{ .dev = 0x40, .num_clks = 1 },
+
+	/* intc0 */
+	{ .dev = 0x41, .num_clks = 1 },
+
+	/* gic0 */
+	{ .dev = 0x42, .num_clks = 1 },
+
+	/* qspi0 */
+	{ .dev = 0x43, .num_clks = 5 },
+
+	/* arm_64b_counter0 */
+	{ .dev = 0x44, .num_clks = 2 },
+
+	/* tetris0 */
+	{ .dev = 0x45, .num_clks = 2 },
+
+	/* cgem0 */
+	{ .dev = 0x46, .num_clks = 2 },
+
+	/* msmc0 */
+	{ .dev = 0x47, .num_clks = 1 },
+
+	/* cbass0 */
+	{ .dev = 0x49, .num_clks = 1 },
+
+	/* board0 */
+	{ .dev = 0x4c, .num_clks = 36 },
+
+	/* edma1 */
+	{ .dev = 0x4f, .num_clks = 2 },
+	{ .num_clks = 0 },
+};
+
+static const struct of_device_id ti_sci_clk_of_match[] = {
+	{ .compatible = "ti,k2g-sci-clk", .data = &k2g_clk_data },
+	{ /* Sentinel */ },
+};
+MODULE_DEVICE_TABLE(of, ti_sci_clk_of_match);
+
+/**
+ * ti_sci_clk_probe - Probe function for the TI SCI clock driver
+ * @pdev: platform device pointer to be probed
+ *
+ * Probes the TI SCI clock device. Allocates a new clock provider
+ * and registers this to the common clock framework. Also applies
+ * any required flags to the identified clocks via clock lists
+ * supplied from DT. Returns 0 for success, negative error value
+ * for failure.
+ */
+static int ti_sci_clk_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct device_node *np = dev->of_node;
+	struct sci_clk_provider *provider;
+	const struct ti_sci_handle *handle;
+	const struct sci_clk_data *data;
+	int ret;
+
+	data = of_device_get_match_data(dev);
+	if (!data)
+		return -EINVAL;
+
+	handle = devm_ti_sci_get_handle(dev);
+	if (IS_ERR(handle))
+		return PTR_ERR(handle);
+
+	provider = devm_kzalloc(dev, sizeof(*provider), GFP_KERNEL);
+	if (!provider)
+		return -ENOMEM;
+
+	provider->clk_data = data;
+
+	provider->sci = handle;
+	provider->ops = &handle->ops.clk_ops;
+	provider->dev = dev;
+
+	ret = ti_sci_init_clocks(provider);
+	if (ret) {
+		pr_err("ti-sci-init-clocks failed.\n");
+		return ret;
+	}
+
+	return of_clk_add_hw_provider(np, sci_clk_get, provider);
+}
+
+/**
+ * ti_sci_clk_remove - Remove TI SCI clock device
+ * @pdev: platform device pointer for the device to be removed
+ *
+ * Removes the TI SCI device. Unregisters the clock provider registered
+ * via common clock framework. Any memory allocated for the device will
+ * be free'd silently via the devm framework. Returns 0 always.
+ */
+static int ti_sci_clk_remove(struct platform_device *pdev)
+{
+	of_clk_del_provider(pdev->dev.of_node);
+
+	return 0;
+}
+
+static struct platform_driver ti_sci_clk_driver = {
+	.probe = ti_sci_clk_probe,
+	.remove = ti_sci_clk_remove,
+	.driver = {
+		.name = "ti-sci-clk",
+		.of_match_table = of_match_ptr(ti_sci_clk_of_match),
+	},
+};
+module_platform_driver(ti_sci_clk_driver);
+
+MODULE_LICENSE("GPL v2");
+MODULE_DESCRIPTION("TI System Control Interface(SCI) Clock driver");
+MODULE_AUTHOR("Tero Kristo");
+MODULE_ALIAS("platform:ti-sci-clk");
-- 
1.9.1