All of lore.kernel.org
 help / color / mirror / Atom feed
From: Varadarajan Narayanan <varada@codeaurora.org>
To: broonie@kernel.org, robh+dt@kernel.org, mark.rutland@arm.com,
	andy.gross@linaro.org, david.brown@linaro.org,
	linux-spi@vger.kernel.org, devicetree@vger.kernel.org,
	linux-kernel@vger.kernel.org, linux-arm-msm@vger.kernel.org,
	linux-soc@vger.kernel.org
Cc: Varadarajan Narayanan <varada@codeaurora.org>
Subject: [PATCH 09/18] spi: qup: Do block sized read/write in block mode
Date: Wed, 14 Jun 2017 11:22:22 +0530	[thread overview]
Message-ID: <1497419551-21834-10-git-send-email-varada@codeaurora.org> (raw)
In-Reply-To: <1497419551-21834-1-git-send-email-varada@codeaurora.org>

This patch corrects the behavior of the BLOCK
transactions.  During block transactions, the controller
must be read/written to in block size transactions.

Signed-off-by: Andy Gross <andy.gross@linaro.org>
Signed-off-by: Varadarajan Narayanan <varada@codeaurora.org>
---
 drivers/spi/spi-qup.c | 151 +++++++++++++++++++++++++++++++++++++++-----------
 1 file changed, 119 insertions(+), 32 deletions(-)

diff --git a/drivers/spi/spi-qup.c b/drivers/spi/spi-qup.c
index 0f6a4c7..872de28 100644
--- a/drivers/spi/spi-qup.c
+++ b/drivers/spi/spi-qup.c
@@ -82,6 +82,8 @@
 #define QUP_IO_M_MODE_BAM		3
 
 /* QUP_OPERATIONAL fields */
+#define QUP_OP_IN_BLOCK_READ_REQ	BIT(13)
+#define QUP_OP_OUT_BLOCK_WRITE_REQ	BIT(12)
 #define QUP_OP_MAX_INPUT_DONE_FLAG	BIT(11)
 #define QUP_OP_MAX_OUTPUT_DONE_FLAG	BIT(10)
 #define QUP_OP_IN_SERVICE_FLAG		BIT(9)
@@ -156,6 +158,13 @@ struct spi_qup {
 	struct dma_slave_config	tx_conf;
 };
 
+static inline bool spi_qup_is_flag_set(struct spi_qup *controller, u32 flag)
+{
+	u32 opflag = readl_relaxed(controller->base + QUP_OPERATIONAL);
+
+	return (opflag & flag) != 0;
+}
+
 static inline bool spi_qup_is_dma_xfer(int mode)
 {
 	if (mode == QUP_IO_M_MODE_DMOV || mode == QUP_IO_M_MODE_BAM)
@@ -216,29 +225,26 @@ static int spi_qup_set_state(struct spi_qup *controller, u32 state)
 	return 0;
 }
 
-static void spi_qup_fifo_read(struct spi_qup *controller,
-			    struct spi_transfer *xfer)
+static void spi_qup_read_from_fifo(struct spi_qup *controller,
+	struct spi_transfer *xfer, u32 num_words)
 {
 	u8 *rx_buf = xfer->rx_buf;
-	u32 word, state;
-	int idx, shift, w_size;
+	int i, shift, num_bytes;
+	u32 word;
 
-	w_size = controller->w_size;
-
-	while (controller->rx_bytes < xfer->len) {
-
-		state = readl_relaxed(controller->base + QUP_OPERATIONAL);
-		if (0 == (state & QUP_OP_IN_FIFO_NOT_EMPTY))
-			break;
+	for (; num_words; num_words--) {
 
 		word = readl_relaxed(controller->base + QUP_INPUT_FIFO);
 
+		num_bytes = min_t(int, xfer->len - controller->rx_bytes,
+					controller->w_size);
+
 		if (!rx_buf) {
-			controller->rx_bytes += w_size;
+			controller->rx_bytes += num_bytes;
 			continue;
 		}
 
-		for (idx = 0; idx < w_size; idx++, controller->rx_bytes++) {
+		for (i = 0; i < num_bytes; i++, controller->rx_bytes++) {
 			/*
 			 * The data format depends on bytes per SPI word:
 			 *  4 bytes: 0x12345678
@@ -246,38 +252,80 @@ static void spi_qup_fifo_read(struct spi_qup *controller,
 			 *  1 byte : 0x00000012
 			 */
 			shift = BITS_PER_BYTE;
-			shift *= (w_size - idx - 1);
+			shift *= (controller->w_size - i - 1);
 			rx_buf[controller->rx_bytes] = word >> shift;
 		}
 	}
 }
 
-static void spi_qup_fifo_write(struct spi_qup *controller,
+static void spi_qup_read(struct spi_qup *controller,
 			    struct spi_transfer *xfer)
 {
-	const u8 *tx_buf = xfer->tx_buf;
-	u32 word, state, data;
-	int idx, w_size;
+	u32 remainder, words_per_block, num_words;
+	bool is_block_mode = controller->mode == QUP_IO_M_MODE_BLOCK;
+
+	remainder = DIV_ROUND_UP(xfer->len - controller->rx_bytes,
+				 controller->w_size);
+	words_per_block = controller->in_blk_sz >> 2;
+
+	do {
+		/* ACK by clearing service flag */
+		writel_relaxed(QUP_OP_IN_SERVICE_FLAG,
+			       controller->base + QUP_OPERATIONAL);
+
+		if (is_block_mode) {
+			num_words = (remainder > words_per_block) ?
+					words_per_block : remainder;
+		} else {
+			if (!spi_qup_is_flag_set(controller,
+						 QUP_OP_IN_FIFO_NOT_EMPTY))
+				break;
 
-	w_size = controller->w_size;
+			num_words = 1;
+		}
 
-	while (controller->tx_bytes < xfer->len) {
+		/* read up to the maximum transfer size available */
+		spi_qup_read_from_fifo(controller, xfer, num_words);
 
-		state = readl_relaxed(controller->base + QUP_OPERATIONAL);
-		if (state & QUP_OP_OUT_FIFO_FULL)
+		remainder -= num_words;
+
+		/* if block mode, check to see if next block is available */
+		if (is_block_mode && !spi_qup_is_flag_set(controller,
+					QUP_OP_IN_BLOCK_READ_REQ))
 			break;
 
+	} while (remainder);
+
+	/*
+	 * Due to extra stickiness of the QUP_OP_IN_SERVICE_FLAG during block
+	 * mode reads, it has to be cleared again at the very end
+	 */
+	if (is_block_mode && spi_qup_is_flag_set(controller,
+				QUP_OP_MAX_INPUT_DONE_FLAG))
+		writel_relaxed(QUP_OP_IN_SERVICE_FLAG,
+			       controller->base + QUP_OPERATIONAL);
+
+}
+
+static void spi_qup_write_to_fifo(struct spi_qup *controller,
+	struct spi_transfer *xfer, u32 num_words)
+{
+	const u8 *tx_buf = xfer->tx_buf;
+	int i, num_bytes;
+	u32 word, data;
+
+	for (; num_words; num_words--) {
 		word = 0;
-		for (idx = 0; idx < w_size; idx++, controller->tx_bytes++) {
 
-			if (!tx_buf) {
-				controller->tx_bytes += w_size;
-				break;
+		num_bytes = min_t(int, xfer->len - controller->tx_bytes,
+				    controller->w_size);
+		if (tx_buf)
+			for (i = 0; i < num_bytes; i++) {
+				data = tx_buf[controller->tx_bytes + i];
+				word |= data << (BITS_PER_BYTE * (3 - i));
 			}
 
-			data = tx_buf[controller->tx_bytes];
-			word |= data << (BITS_PER_BYTE * (3 - idx));
-		}
+		controller->tx_bytes += num_bytes;
 
 		writel_relaxed(word, controller->base + QUP_OUTPUT_FIFO);
 	}
@@ -288,6 +336,44 @@ static void spi_qup_dma_done(void *data)
 	complete(data);
 }
 
+static void spi_qup_write(struct spi_qup *controller,
+			    struct spi_transfer *xfer)
+{
+	bool is_block_mode = controller->mode == QUP_IO_M_MODE_BLOCK;
+	u32 remainder, words_per_block, num_words;
+
+	remainder = DIV_ROUND_UP(xfer->len - controller->tx_bytes,
+				 controller->w_size);
+	words_per_block = controller->out_blk_sz >> 2;
+
+	do {
+		/* ACK by clearing service flag */
+		writel_relaxed(QUP_OP_OUT_SERVICE_FLAG,
+			       controller->base + QUP_OPERATIONAL);
+
+		if (is_block_mode) {
+			num_words = (remainder > words_per_block) ?
+				words_per_block : remainder;
+		} else {
+			if (spi_qup_is_flag_set(controller,
+						QUP_OP_OUT_FIFO_FULL))
+				break;
+
+			num_words = 1;
+		}
+
+		spi_qup_write_to_fifo(controller, xfer, num_words);
+
+		remainder -= num_words;
+
+		/* if block mode, check to see if next block is available */
+		if (is_block_mode && !spi_qup_is_flag_set(controller,
+					QUP_OP_OUT_BLOCK_WRITE_REQ))
+			break;
+
+	} while (remainder);
+}
+
 static int spi_qup_prep_sg(struct spi_master *master, struct spi_transfer *xfer,
 			   enum dma_transfer_direction dir,
 			   dma_async_tx_callback callback, void *data)
@@ -390,7 +476,8 @@ static int spi_qup_do_pio(struct spi_master *master, struct spi_transfer *xfer,
 		return ret;
 	}
 
-	spi_qup_fifo_write(qup, xfer);
+	if (qup->mode == QUP_IO_M_MODE_FIFO)
+		spi_qup_write(qup, xfer);
 
 	ret = spi_qup_set_state(qup, QUP_STATE_RUN);
 	if (ret) {
@@ -455,10 +542,10 @@ static irqreturn_t spi_qup_qup_irq(int irq, void *dev_id)
 
 	if (!spi_qup_is_dma_xfer(controller->mode)) {
 		if (opflags & QUP_OP_IN_SERVICE_FLAG)
-			spi_qup_fifo_read(controller, xfer);
+			spi_qup_read(controller, xfer);
 
 		if (opflags & QUP_OP_OUT_SERVICE_FLAG)
-			spi_qup_fifo_write(controller, xfer);
+			spi_qup_write(controller, xfer);
 	}
 
 	spin_lock_irqsave(&controller->lock, flags);
-- 
QUALCOMM INDIA, on behalf of Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum, hosted by The Linux Foundation

  parent reply	other threads:[~2017-06-14  5:53 UTC|newest]

Thread overview: 46+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2017-06-14  5:52 [PATCH 00/18] spi: qup: Fixes and add support for >64k transfers Varadarajan Narayanan
2017-06-14  5:52 ` Varadarajan Narayanan
2017-06-14  5:52 ` [PATCH 01/18] spi: qup: Enable chip select support Varadarajan Narayanan
2017-06-14  9:47   ` Stanimir Varbanov
2017-08-08 11:18   ` Applied "spi: qup: Enable chip select support" to the spi tree Mark Brown
2017-08-08 11:18     ` Mark Brown
     [not found] ` <1497419551-21834-1-git-send-email-varada-sgV2jX0FEOL9JmXXK+q4OQ@public.gmane.org>
2017-06-14  5:52   ` [PATCH 02/18] spi: qup: Setup DMA mode correctly Varadarajan Narayanan
2017-06-14  5:52     ` Varadarajan Narayanan
2017-08-08 11:18     ` Applied "spi: qup: Setup DMA mode correctly" to the spi tree Mark Brown
2017-08-08 11:18       ` Mark Brown
2017-06-14  5:52   ` [PATCH 06/18] spi: qup: Fix error handling in spi_qup_prep_sg Varadarajan Narayanan
2017-06-14  5:52     ` Varadarajan Narayanan
2017-06-14  5:52 ` [PATCH 03/18] spi: qup: Add completion timeout for dma mode Varadarajan Narayanan
2017-06-14  5:52 ` [PATCH 04/18] spi: qup: Add completion timeout for fifo/block mode Varadarajan Narayanan
2017-06-14  5:52 ` [PATCH 05/18] spi: qup: Place the QUP in run mode before DMA transactions Varadarajan Narayanan
2017-06-14  5:52 ` [PATCH 07/18] spi: qup: Fix transaction done signaling Varadarajan Narayanan
2017-06-14  7:13   ` Sricharan R
     [not found]     ` <4b81a4c7-b85c-a35d-15fb-4aaaec3c7e8c-sgV2jX0FEOL9JmXXK+q4OQ@public.gmane.org>
2017-06-14 19:51       ` Andy Gross
2017-06-14 19:51         ` Andy Gross
     [not found]         ` <20170614195155.GB32733-5taXn+FmohyKb9UB7mSz9QC/G2K4zDHf@public.gmane.org>
2017-06-15  5:14           ` Sricharan R
2017-06-15  5:14             ` Sricharan R
2017-06-14  5:52 ` [PATCH 08/18] spi: qup: Handle v1 dma completion differently Varadarajan Narayanan
     [not found]   ` <1497419551-21834-9-git-send-email-varada-sgV2jX0FEOL9JmXXK+q4OQ@public.gmane.org>
2017-06-14  7:15     ` Sricharan R
2017-06-14  7:15       ` Sricharan R
     [not found]       ` <a0e499a7-8f89-96d6-9463-c2b3f774cd6d-sgV2jX0FEOL9JmXXK+q4OQ@public.gmane.org>
2017-06-14 19:53         ` Andy Gross
2017-06-14 19:53           ` Andy Gross
2017-06-14  5:52 ` Varadarajan Narayanan [this message]
2017-06-14  5:52 ` [PATCH 10/18] spi: qup: Fix DMA mode interrupt handling Varadarajan Narayanan
2017-06-14  7:21   ` Sricharan R
     [not found]     ` <66ba7dfb-6ff3-884e-6db0-8d5191f87c93-sgV2jX0FEOL9JmXXK+q4OQ@public.gmane.org>
2017-06-14 20:06       ` Andy Gross
2017-06-14 20:06         ` Andy Gross
2017-06-15  5:52         ` Sricharan R
2017-06-14  5:52 ` [PATCH 11/18] spi: qup: properly detect extra interrupts Varadarajan Narayanan
     [not found]   ` <1497419551-21834-12-git-send-email-varada-sgV2jX0FEOL9JmXXK+q4OQ@public.gmane.org>
2017-06-14  7:27     ` Sricharan R
2017-06-14  7:27       ` Sricharan R
2017-06-14 19:59       ` Andy Gross
     [not found]         ` <20170614195953.GD32733-5taXn+FmohyKb9UB7mSz9QC/G2K4zDHf@public.gmane.org>
2017-06-14 21:51           ` Matthew McClintock
2017-06-14 21:51             ` Matthew McClintock
2017-06-15  5:27         ` Sricharan R
2017-06-14  5:52 ` [PATCH 12/18] spi: qup: refactor spi_qup_io_config into two functions Varadarajan Narayanan
2017-06-14  5:52 ` [PATCH 13/18] spi: qup: call io_config in mode specific function Varadarajan Narayanan
2017-06-14  5:52 ` [PATCH 14/18] spi: qup: allow block mode to generate multiple transactions Varadarajan Narayanan
2017-06-14  5:52 ` [PATCH 15/18] spi: qup: refactor spi_qup_prep_sg Varadarajan Narayanan
2017-06-14  5:52 ` [PATCH 16/18] spi: qup: allow multiple DMA transactions per spi xfer Varadarajan Narayanan
2017-06-14  5:52 ` [PATCH 17/18] spi: qup: Ensure done detection Varadarajan Narayanan
2017-06-14  5:52 ` [PATCH 18/18] spi: qup: support for qup v1 dma Varadarajan Narayanan

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=1497419551-21834-10-git-send-email-varada@codeaurora.org \
    --to=varada@codeaurora.org \
    --cc=andy.gross@linaro.org \
    --cc=broonie@kernel.org \
    --cc=david.brown@linaro.org \
    --cc=devicetree@vger.kernel.org \
    --cc=linux-arm-msm@vger.kernel.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=linux-soc@vger.kernel.org \
    --cc=linux-spi@vger.kernel.org \
    --cc=mark.rutland@arm.com \
    --cc=robh+dt@kernel.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.