All of lore.kernel.org
 help / color / mirror / Atom feed
From: Varadarajan Narayanan <varada@codeaurora.org>
To: broonie@kernel.org, robh+dt@kernel.org, mark.rutland@arm.com,
	andy.gross@linaro.org, david.brown@linaro.org,
	linux-spi@vger.kernel.org, devicetree@vger.kernel.org,
	linux-kernel@vger.kernel.org, linux-arm-msm@vger.kernel.org,
	linux-soc@vger.kernel.org
Cc: Varadarajan Narayanan <varada@codeaurora.org>,
	Matthew McClintock <mmcclint@codeaurora.org>
Subject: [PATCH 14/18] spi: qup: allow block mode to generate multiple transactions
Date: Wed, 14 Jun 2017 11:22:27 +0530	[thread overview]
Message-ID: <1497419551-21834-15-git-send-email-varada@codeaurora.org> (raw)
In-Reply-To: <1497419551-21834-1-git-send-email-varada@codeaurora.org>

This let's you write more to the SPI bus than 64K-1 which is important
if the block size of a SPI device is >= 64K or some other device wants
to do something larger.

This has the benefit of completely removing spi_message from the spi-qup
transactions

Signed-off-by: Matthew McClintock <mmcclint@codeaurora.org>
Signed-off-by: Varadarajan Narayanan <varada@codeaurora.org>
---
 drivers/spi/spi-qup.c | 127 +++++++++++++++++++++++++++++++-------------------
 1 file changed, 80 insertions(+), 47 deletions(-)

diff --git a/drivers/spi/spi-qup.c b/drivers/spi/spi-qup.c
index f085e36..02d4e10 100644
--- a/drivers/spi/spi-qup.c
+++ b/drivers/spi/spi-qup.c
@@ -120,7 +120,7 @@
 
 #define SPI_NUM_CHIPSELECTS		4
 
-#define SPI_MAX_DMA_XFER		(SZ_64K - 64)
+#define SPI_MAX_XFER			(SZ_64K - 64)
 
 /* high speed mode is when bus rate is greater then 26MHz */
 #define SPI_HS_MIN_RATE			26000000
@@ -151,6 +151,8 @@ struct spi_qup {
 	int			n_words;
 	int			tx_bytes;
 	int			rx_bytes;
+	const u8		*tx_buf;
+	u8			*rx_buf;
 	int			qup_v1;
 
 	int			mode;
@@ -175,6 +177,12 @@ static inline bool spi_qup_is_dma_xfer(int mode)
 	return false;
 }
 
+/* get's the transaction size length */
+static inline unsigned int spi_qup_len(struct spi_qup *controller)
+{
+	return controller->n_words * controller->w_size;
+}
+
 static inline bool spi_qup_is_valid_state(struct spi_qup *controller)
 {
 	u32 opstate = readl_relaxed(controller->base + QUP_STATE);
@@ -227,10 +235,9 @@ static int spi_qup_set_state(struct spi_qup *controller, u32 state)
 	return 0;
 }
 
-static void spi_qup_read_from_fifo(struct spi_qup *controller,
-	struct spi_transfer *xfer, u32 num_words)
+static void spi_qup_read_from_fifo(struct spi_qup *controller, u32 num_words)
 {
-	u8 *rx_buf = xfer->rx_buf;
+	u8 *rx_buf = controller->rx_buf;
 	int i, shift, num_bytes;
 	u32 word;
 
@@ -238,8 +245,9 @@ static void spi_qup_read_from_fifo(struct spi_qup *controller,
 
 		word = readl_relaxed(controller->base + QUP_INPUT_FIFO);
 
-		num_bytes = min_t(int, xfer->len - controller->rx_bytes,
-					controller->w_size);
+		num_bytes = min_t(int, spi_qup_len(controller) -
+				       controller->rx_bytes,
+				       controller->w_size);
 
 		if (!rx_buf) {
 			controller->rx_bytes += num_bytes;
@@ -260,13 +268,12 @@ static void spi_qup_read_from_fifo(struct spi_qup *controller,
 	}
 }
 
-static void spi_qup_read(struct spi_qup *controller,
-			    struct spi_transfer *xfer)
+static void spi_qup_read(struct spi_qup *controller)
 {
 	u32 remainder, words_per_block, num_words;
 	bool is_block_mode = controller->mode == QUP_IO_M_MODE_BLOCK;
 
-	remainder = DIV_ROUND_UP(xfer->len - controller->rx_bytes,
+	remainder = DIV_ROUND_UP(spi_qup_len(controller) - controller->rx_bytes,
 				 controller->w_size);
 	words_per_block = controller->in_blk_sz >> 2;
 
@@ -287,7 +294,7 @@ static void spi_qup_read(struct spi_qup *controller,
 		}
 
 		/* read up to the maximum transfer size available */
-		spi_qup_read_from_fifo(controller, xfer, num_words);
+		spi_qup_read_from_fifo(controller, num_words);
 
 		remainder -= num_words;
 
@@ -309,18 +316,18 @@ static void spi_qup_read(struct spi_qup *controller,
 
 }
 
-static void spi_qup_write_to_fifo(struct spi_qup *controller,
-	struct spi_transfer *xfer, u32 num_words)
+static void spi_qup_write_to_fifo(struct spi_qup *controller, u32 num_words)
 {
-	const u8 *tx_buf = xfer->tx_buf;
+	const u8 *tx_buf = controller->tx_buf;
 	int i, num_bytes;
 	u32 word, data;
 
 	for (; num_words; num_words--) {
 		word = 0;
 
-		num_bytes = min_t(int, xfer->len - controller->tx_bytes,
-				    controller->w_size);
+		num_bytes = min_t(int, spi_qup_len(controller) -
+				       controller->tx_bytes,
+				       controller->w_size);
 		if (tx_buf)
 			for (i = 0; i < num_bytes; i++) {
 				data = tx_buf[controller->tx_bytes + i];
@@ -338,13 +345,12 @@ static void spi_qup_dma_done(void *data)
 	complete(data);
 }
 
-static void spi_qup_write(struct spi_qup *controller,
-			    struct spi_transfer *xfer)
+static void spi_qup_write(struct spi_qup *controller)
 {
 	bool is_block_mode = controller->mode == QUP_IO_M_MODE_BLOCK;
 	u32 remainder, words_per_block, num_words;
 
-	remainder = DIV_ROUND_UP(xfer->len - controller->tx_bytes,
+	remainder = DIV_ROUND_UP(spi_qup_len(controller) - controller->tx_bytes,
 				 controller->w_size);
 	words_per_block = controller->out_blk_sz >> 2;
 
@@ -364,7 +370,7 @@ static void spi_qup_write(struct spi_qup *controller,
 			num_words = 1;
 		}
 
-		spi_qup_write_to_fifo(controller, xfer, num_words);
+		spi_qup_write_to_fifo(controller, num_words);
 
 		remainder -= num_words;
 
@@ -470,36 +476,62 @@ static int spi_qup_do_pio(struct spi_device *spi, struct spi_transfer *xfer,
 {
 	struct spi_master *master = spi->master;
 	struct spi_qup *qup = spi_master_get_devdata(master);
-	int ret;
+	int ret, n_words, iterations, offset = 0;
 
-	ret = spi_qup_io_config(spi, xfer);
-	if (ret)
-		return ret;
+	n_words = qup->n_words;
+	iterations = n_words / SPI_MAX_XFER; /* round down */
+	qup->rx_buf = xfer->rx_buf;
+	qup->tx_buf = xfer->tx_buf;
 
-	ret = spi_qup_set_state(qup, QUP_STATE_RUN);
-	if (ret) {
-		dev_warn(qup->dev, "%s(%d): cannot set RUN state\n");
-		return ret;
-	}
+	do {
+		if (iterations)
+			qup->n_words = SPI_MAX_XFER;
+		else
+			qup->n_words = n_words % SPI_MAX_XFER;
 
-	ret = spi_qup_set_state(qup, QUP_STATE_PAUSE);
-	if (ret) {
-		dev_warn(qup->dev, "%s(%d): cannot set PAUSE state\n");
-		return ret;
-	}
+		if (qup->tx_buf && offset)
+			qup->tx_buf = xfer->tx_buf + offset * SPI_MAX_XFER;
 
-	if (qup->mode == QUP_IO_M_MODE_FIFO)
-		spi_qup_write(qup, xfer);
+		if (qup->rx_buf && offset)
+			qup->rx_buf = xfer->rx_buf + offset * SPI_MAX_XFER;
 
-	ret = spi_qup_set_state(qup, QUP_STATE_RUN);
-	if (ret) {
-		dev_warn(qup->dev, "%s(%d): cannot set RUN state\n");
-		return ret;
-	}
+		/*
+		 * if the transaction is small enough, we need
+		 * to fallback to FIFO mode
+		 */
+		if (qup->n_words <= (qup->in_fifo_sz / sizeof(u32)))
+			qup->mode = QUP_IO_M_MODE_FIFO;
 
-	if (!wait_for_completion_timeout(&qup->done, timeout))
-		return -ETIMEDOUT;
+		ret = spi_qup_io_config(spi, xfer);
+		if (ret)
+			return ret;
+
+		ret = spi_qup_set_state(qup, QUP_STATE_RUN);
+		if (ret) {
+			dev_warn(qup->dev, "cannot set RUN state\n");
+			return ret;
+		}
+
+		ret = spi_qup_set_state(qup, QUP_STATE_PAUSE);
+		if (ret) {
+			dev_warn(qup->dev, "cannot set PAUSE state\n");
+			return ret;
+		}
+
+		if (qup->mode == QUP_IO_M_MODE_FIFO)
+			spi_qup_write(qup);
+
+		ret = spi_qup_set_state(qup, QUP_STATE_RUN);
+		if (ret) {
+			dev_warn(qup->dev, "cannot set RUN state\n");
+			return ret;
+		}
+
+		if (!wait_for_completion_timeout(&qup->done, timeout))
+			return -ETIMEDOUT;
 
+		offset++;
+	} while (iterations--);
 	return 0;
 }
 
@@ -562,16 +594,16 @@ static irqreturn_t spi_qup_qup_irq(int irq, void *dev_id)
 			complete(&controller->txc);
 	} else {
 		if (opflags & QUP_OP_IN_SERVICE_FLAG)
-			spi_qup_read(controller, xfer);
+			spi_qup_read(controller);
 
 		if (opflags & QUP_OP_OUT_SERVICE_FLAG)
-			spi_qup_write(controller, xfer);
+			spi_qup_write(controller);
 	}
 
 	/* re-read opflags as flags may have changed due to actions above */
 	opflags = readl_relaxed(controller->base + QUP_OPERATIONAL);
 
-	if ((controller->rx_bytes == xfer->len &&
+	if ((controller->rx_bytes == spi_qup_len(controller) &&
 		(opflags & QUP_OP_MAX_INPUT_DONE_FLAG)) ||  error)
 		done = true;
 
@@ -787,7 +819,8 @@ static int spi_qup_transfer_one(struct spi_master *master,
 		return ret;
 
 	timeout = DIV_ROUND_UP(xfer->speed_hz, MSEC_PER_SEC);
-	timeout = DIV_ROUND_UP(xfer->len * 8, timeout);
+	timeout = DIV_ROUND_UP(min_t(unsigned long, SPI_MAX_XFER,
+				     xfer->len) * 8, timeout);
 	timeout = 100 * msecs_to_jiffies(timeout);
 
 	if (spi_qup_is_dma_xfer(controller->mode))
@@ -992,7 +1025,7 @@ static int spi_qup_probe(struct platform_device *pdev)
 	master->dev.of_node = pdev->dev.of_node;
 	master->auto_runtime_pm = true;
 	master->dma_alignment = dma_get_cache_alignment();
-	master->max_dma_len = SPI_MAX_DMA_XFER;
+	master->max_dma_len = SPI_MAX_XFER;
 
 	platform_set_drvdata(pdev, master);
 
-- 
QUALCOMM INDIA, on behalf of Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum, hosted by The Linux Foundation

  parent reply	other threads:[~2017-06-14  5:52 UTC|newest]

Thread overview: 46+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2017-06-14  5:52 [PATCH 00/18] spi: qup: Fixes and add support for >64k transfers Varadarajan Narayanan
2017-06-14  5:52 ` Varadarajan Narayanan
2017-06-14  5:52 ` [PATCH 01/18] spi: qup: Enable chip select support Varadarajan Narayanan
2017-06-14  9:47   ` Stanimir Varbanov
2017-08-08 11:18   ` Applied "spi: qup: Enable chip select support" to the spi tree Mark Brown
2017-08-08 11:18     ` Mark Brown
     [not found] ` <1497419551-21834-1-git-send-email-varada-sgV2jX0FEOL9JmXXK+q4OQ@public.gmane.org>
2017-06-14  5:52   ` [PATCH 02/18] spi: qup: Setup DMA mode correctly Varadarajan Narayanan
2017-06-14  5:52     ` Varadarajan Narayanan
2017-08-08 11:18     ` Applied "spi: qup: Setup DMA mode correctly" to the spi tree Mark Brown
2017-08-08 11:18       ` Mark Brown
2017-06-14  5:52   ` [PATCH 06/18] spi: qup: Fix error handling in spi_qup_prep_sg Varadarajan Narayanan
2017-06-14  5:52     ` Varadarajan Narayanan
2017-06-14  5:52 ` [PATCH 03/18] spi: qup: Add completion timeout for dma mode Varadarajan Narayanan
2017-06-14  5:52 ` [PATCH 04/18] spi: qup: Add completion timeout for fifo/block mode Varadarajan Narayanan
2017-06-14  5:52 ` [PATCH 05/18] spi: qup: Place the QUP in run mode before DMA transactions Varadarajan Narayanan
2017-06-14  5:52 ` [PATCH 07/18] spi: qup: Fix transaction done signaling Varadarajan Narayanan
2017-06-14  7:13   ` Sricharan R
     [not found]     ` <4b81a4c7-b85c-a35d-15fb-4aaaec3c7e8c-sgV2jX0FEOL9JmXXK+q4OQ@public.gmane.org>
2017-06-14 19:51       ` Andy Gross
2017-06-14 19:51         ` Andy Gross
     [not found]         ` <20170614195155.GB32733-5taXn+FmohyKb9UB7mSz9QC/G2K4zDHf@public.gmane.org>
2017-06-15  5:14           ` Sricharan R
2017-06-15  5:14             ` Sricharan R
2017-06-14  5:52 ` [PATCH 08/18] spi: qup: Handle v1 dma completion differently Varadarajan Narayanan
     [not found]   ` <1497419551-21834-9-git-send-email-varada-sgV2jX0FEOL9JmXXK+q4OQ@public.gmane.org>
2017-06-14  7:15     ` Sricharan R
2017-06-14  7:15       ` Sricharan R
     [not found]       ` <a0e499a7-8f89-96d6-9463-c2b3f774cd6d-sgV2jX0FEOL9JmXXK+q4OQ@public.gmane.org>
2017-06-14 19:53         ` Andy Gross
2017-06-14 19:53           ` Andy Gross
2017-06-14  5:52 ` [PATCH 09/18] spi: qup: Do block sized read/write in block mode Varadarajan Narayanan
2017-06-14  5:52 ` [PATCH 10/18] spi: qup: Fix DMA mode interrupt handling Varadarajan Narayanan
2017-06-14  7:21   ` Sricharan R
     [not found]     ` <66ba7dfb-6ff3-884e-6db0-8d5191f87c93-sgV2jX0FEOL9JmXXK+q4OQ@public.gmane.org>
2017-06-14 20:06       ` Andy Gross
2017-06-14 20:06         ` Andy Gross
2017-06-15  5:52         ` Sricharan R
2017-06-14  5:52 ` [PATCH 11/18] spi: qup: properly detect extra interrupts Varadarajan Narayanan
     [not found]   ` <1497419551-21834-12-git-send-email-varada-sgV2jX0FEOL9JmXXK+q4OQ@public.gmane.org>
2017-06-14  7:27     ` Sricharan R
2017-06-14  7:27       ` Sricharan R
2017-06-14 19:59       ` Andy Gross
     [not found]         ` <20170614195953.GD32733-5taXn+FmohyKb9UB7mSz9QC/G2K4zDHf@public.gmane.org>
2017-06-14 21:51           ` Matthew McClintock
2017-06-14 21:51             ` Matthew McClintock
2017-06-15  5:27         ` Sricharan R
2017-06-14  5:52 ` [PATCH 12/18] spi: qup: refactor spi_qup_io_config into two functions Varadarajan Narayanan
2017-06-14  5:52 ` [PATCH 13/18] spi: qup: call io_config in mode specific function Varadarajan Narayanan
2017-06-14  5:52 ` Varadarajan Narayanan [this message]
2017-06-14  5:52 ` [PATCH 15/18] spi: qup: refactor spi_qup_prep_sg Varadarajan Narayanan
2017-06-14  5:52 ` [PATCH 16/18] spi: qup: allow multiple DMA transactions per spi xfer Varadarajan Narayanan
2017-06-14  5:52 ` [PATCH 17/18] spi: qup: Ensure done detection Varadarajan Narayanan
2017-06-14  5:52 ` [PATCH 18/18] spi: qup: support for qup v1 dma Varadarajan Narayanan

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=1497419551-21834-15-git-send-email-varada@codeaurora.org \
    --to=varada@codeaurora.org \
    --cc=andy.gross@linaro.org \
    --cc=broonie@kernel.org \
    --cc=david.brown@linaro.org \
    --cc=devicetree@vger.kernel.org \
    --cc=linux-arm-msm@vger.kernel.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=linux-soc@vger.kernel.org \
    --cc=linux-spi@vger.kernel.org \
    --cc=mark.rutland@arm.com \
    --cc=mmcclint@codeaurora.org \
    --cc=robh+dt@kernel.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.