From: Varadarajan Narayanan <varada-sgV2jX0FEOL9JmXXK+q4OQ@public.gmane.org>
To: broonie-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org,
robh+dt-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org,
mark.rutland-5wv7dgnIgG8@public.gmane.org,
andy.gross-QSEj5FYQhm4dnm+yROfE0A@public.gmane.org,
david.brown-QSEj5FYQhm4dnm+yROfE0A@public.gmane.org,
linux-spi-u79uwXL29TY76Z2rM5mHXA@public.gmane.org,
devicetree-u79uwXL29TY76Z2rM5mHXA@public.gmane.org,
linux-kernel-u79uwXL29TY76Z2rM5mHXA@public.gmane.org,
linux-arm-msm-u79uwXL29TY76Z2rM5mHXA@public.gmane.org,
linux-soc-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
Cc: Varadarajan Narayanan <varada-sgV2jX0FEOL9JmXXK+q4OQ@public.gmane.org>
Subject: [PATCH v5 02/14] spi: qup: Setup DMA mode correctly
Date: Mon, 24 Jul 2017 13:17:13 +0530 [thread overview]
Message-ID: <1500882445-29008-3-git-send-email-varada@codeaurora.org> (raw)
In-Reply-To: <1500882445-29008-1-git-send-email-varada-sgV2jX0FEOL9JmXXK+q4OQ@public.gmane.org>
To operate in DMA mode, the buffer should be aligned and
the size of the transfer should be a multiple of block size
(for v1). And the no. of words being transferred should
be programmed in the count registers appropriately.
Signed-off-by: Andy Gross <andy.gross-QSEj5FYQhm4dnm+yROfE0A@public.gmane.org>
Signed-off-by: Varadarajan Narayanan <varada-sgV2jX0FEOL9JmXXK+q4OQ@public.gmane.org>
---
drivers/spi/spi-qup.c | 118 +++++++++++++++++++++++---------------------------
1 file changed, 55 insertions(+), 63 deletions(-)
diff --git a/drivers/spi/spi-qup.c b/drivers/spi/spi-qup.c
index c0d4def..abe799b 100644
--- a/drivers/spi/spi-qup.c
+++ b/drivers/spi/spi-qup.c
@@ -149,11 +149,18 @@ struct spi_qup {
int rx_bytes;
int qup_v1;
- int use_dma;
+ int mode;
struct dma_slave_config rx_conf;
struct dma_slave_config tx_conf;
};
+static inline bool spi_qup_is_dma_xfer(int mode)
+{
+ if (mode == QUP_IO_M_MODE_DMOV || mode == QUP_IO_M_MODE_BAM)
+ return true;
+
+ return false;
+}
static inline bool spi_qup_is_valid_state(struct spi_qup *controller)
{
@@ -424,7 +431,7 @@ static irqreturn_t spi_qup_qup_irq(int irq, void *dev_id)
error = -EIO;
}
- if (!controller->use_dma) {
+ if (!spi_qup_is_dma_xfer(controller->mode)) {
if (opflags & QUP_OP_IN_SERVICE_FLAG)
spi_qup_fifo_read(controller, xfer);
@@ -443,34 +450,11 @@ static irqreturn_t spi_qup_qup_irq(int irq, void *dev_id)
return IRQ_HANDLED;
}
-static u32
-spi_qup_get_mode(struct spi_master *master, struct spi_transfer *xfer)
-{
- struct spi_qup *qup = spi_master_get_devdata(master);
- u32 mode;
-
- qup->w_size = 4;
-
- if (xfer->bits_per_word <= 8)
- qup->w_size = 1;
- else if (xfer->bits_per_word <= 16)
- qup->w_size = 2;
-
- qup->n_words = xfer->len / qup->w_size;
-
- if (qup->n_words <= (qup->in_fifo_sz / sizeof(u32)))
- mode = QUP_IO_M_MODE_FIFO;
- else
- mode = QUP_IO_M_MODE_BLOCK;
-
- return mode;
-}
-
/* set clock freq ... bits per word */
static int spi_qup_io_config(struct spi_device *spi, struct spi_transfer *xfer)
{
struct spi_qup *controller = spi_master_get_devdata(spi->master);
- u32 config, iomode, mode, control;
+ u32 config, iomode, control;
int ret, n_words;
if (spi->mode & SPI_LOOP && xfer->len > controller->in_fifo_sz) {
@@ -491,25 +475,30 @@ static int spi_qup_io_config(struct spi_device *spi, struct spi_transfer *xfer)
return -EIO;
}
- mode = spi_qup_get_mode(spi->master, xfer);
+ controller->w_size = DIV_ROUND_UP(xfer->bits_per_word, 8);
+ controller->n_words = xfer->len / controller->w_size;
n_words = controller->n_words;
- if (mode == QUP_IO_M_MODE_FIFO) {
+ if (n_words <= (controller->in_fifo_sz / sizeof(u32))) {
+
+ controller->mode = QUP_IO_M_MODE_FIFO;
+
writel_relaxed(n_words, controller->base + QUP_MX_READ_CNT);
writel_relaxed(n_words, controller->base + QUP_MX_WRITE_CNT);
/* must be zero for FIFO */
writel_relaxed(0, controller->base + QUP_MX_INPUT_CNT);
writel_relaxed(0, controller->base + QUP_MX_OUTPUT_CNT);
- } else if (!controller->use_dma) {
+ } else if (spi->master->can_dma &&
+ spi->master->can_dma(spi->master, spi, xfer) &&
+ spi->master->cur_msg_mapped) {
+
+ controller->mode = QUP_IO_M_MODE_BAM;
+
writel_relaxed(n_words, controller->base + QUP_MX_INPUT_CNT);
writel_relaxed(n_words, controller->base + QUP_MX_OUTPUT_CNT);
/* must be zero for BLOCK and BAM */
writel_relaxed(0, controller->base + QUP_MX_READ_CNT);
writel_relaxed(0, controller->base + QUP_MX_WRITE_CNT);
- } else {
- mode = QUP_IO_M_MODE_BAM;
- writel_relaxed(0, controller->base + QUP_MX_READ_CNT);
- writel_relaxed(0, controller->base + QUP_MX_WRITE_CNT);
if (!controller->qup_v1) {
void __iomem *input_cnt;
@@ -528,19 +517,28 @@ static int spi_qup_io_config(struct spi_device *spi, struct spi_transfer *xfer)
writel_relaxed(0, controller->base + QUP_MX_OUTPUT_CNT);
}
+ } else {
+
+ controller->mode = QUP_IO_M_MODE_BLOCK;
+
+ writel_relaxed(n_words, controller->base + QUP_MX_INPUT_CNT);
+ writel_relaxed(n_words, controller->base + QUP_MX_OUTPUT_CNT);
+ /* must be zero for BLOCK and BAM */
+ writel_relaxed(0, controller->base + QUP_MX_READ_CNT);
+ writel_relaxed(0, controller->base + QUP_MX_WRITE_CNT);
}
iomode = readl_relaxed(controller->base + QUP_IO_M_MODES);
/* Set input and output transfer mode */
iomode &= ~(QUP_IO_M_INPUT_MODE_MASK | QUP_IO_M_OUTPUT_MODE_MASK);
- if (!controller->use_dma)
+ if (!spi_qup_is_dma_xfer(controller->mode))
iomode &= ~(QUP_IO_M_PACK_EN | QUP_IO_M_UNPACK_EN);
else
iomode |= QUP_IO_M_PACK_EN | QUP_IO_M_UNPACK_EN;
- iomode |= (mode << QUP_IO_M_OUTPUT_MODE_MASK_SHIFT);
- iomode |= (mode << QUP_IO_M_INPUT_MODE_MASK_SHIFT);
+ iomode |= (controller->mode << QUP_IO_M_OUTPUT_MODE_MASK_SHIFT);
+ iomode |= (controller->mode << QUP_IO_M_INPUT_MODE_MASK_SHIFT);
writel_relaxed(iomode, controller->base + QUP_IO_M_MODES);
@@ -581,7 +579,7 @@ static int spi_qup_io_config(struct spi_device *spi, struct spi_transfer *xfer)
config |= xfer->bits_per_word - 1;
config |= QUP_CONFIG_SPI_MODE;
- if (controller->use_dma) {
+ if (spi_qup_is_dma_xfer(controller->mode)) {
if (!xfer->tx_buf)
config |= QUP_CONFIG_NO_OUTPUT;
if (!xfer->rx_buf)
@@ -599,7 +597,7 @@ static int spi_qup_io_config(struct spi_device *spi, struct spi_transfer *xfer)
* status change in BAM mode
*/
- if (mode == QUP_IO_M_MODE_BAM)
+ if (spi_qup_is_dma_xfer(controller->mode))
mask = QUP_OP_IN_SERVICE_FLAG | QUP_OP_OUT_SERVICE_FLAG;
writel_relaxed(mask, controller->base + QUP_OPERATIONAL_MASK);
@@ -633,7 +631,7 @@ static int spi_qup_transfer_one(struct spi_master *master,
controller->tx_bytes = 0;
spin_unlock_irqrestore(&controller->lock, flags);
- if (controller->use_dma)
+ if (spi_qup_is_dma_xfer(controller->mode))
ret = spi_qup_do_dma(master, xfer);
else
ret = spi_qup_do_pio(master, xfer);
@@ -641,14 +639,6 @@ static int spi_qup_transfer_one(struct spi_master *master,
if (ret)
goto exit;
- if (spi_qup_set_state(controller, QUP_STATE_RUN)) {
- dev_warn(controller->dev, "cannot set EXECUTE state\n");
- goto exit;
- }
-
- if (!wait_for_completion_timeout(&controller->done, timeout))
- ret = -ETIMEDOUT;
-
exit:
spi_qup_set_state(controller, QUP_STATE_RESET);
spin_lock_irqsave(&controller->lock, flags);
@@ -657,7 +647,7 @@ static int spi_qup_transfer_one(struct spi_master *master,
ret = controller->error;
spin_unlock_irqrestore(&controller->lock, flags);
- if (ret && controller->use_dma)
+ if (ret && spi_qup_is_dma_xfer(controller->mode))
spi_qup_dma_terminate(master, xfer);
return ret;
@@ -668,26 +658,28 @@ static bool spi_qup_can_dma(struct spi_master *master, struct spi_device *spi,
{
struct spi_qup *qup = spi_master_get_devdata(master);
size_t dma_align = dma_get_cache_alignment();
- u32 mode;
-
- qup->use_dma = 0;
+ int n_words;
- if (xfer->rx_buf && (xfer->len % qup->in_blk_sz ||
- IS_ERR_OR_NULL(master->dma_rx) ||
- !IS_ALIGNED((size_t)xfer->rx_buf, dma_align)))
- return false;
+ if (xfer->rx_buf) {
+ if (!IS_ALIGNED((size_t)xfer->rx_buf, dma_align) ||
+ IS_ERR_OR_NULL(master->dma_rx))
+ return false;
+ if (qup->qup_v1 && (xfer->len % qup->in_blk_sz))
+ return false;
+ }
- if (xfer->tx_buf && (xfer->len % qup->out_blk_sz ||
- IS_ERR_OR_NULL(master->dma_tx) ||
- !IS_ALIGNED((size_t)xfer->tx_buf, dma_align)))
- return false;
+ if (xfer->tx_buf) {
+ if (!IS_ALIGNED((size_t)xfer->tx_buf, dma_align) ||
+ IS_ERR_OR_NULL(master->dma_tx))
+ return false;
+ if (qup->qup_v1 && (xfer->len % qup->out_blk_sz))
+ return false;
+ }
- mode = spi_qup_get_mode(master, xfer);
- if (mode == QUP_IO_M_MODE_FIFO)
+ n_words = xfer->len / DIV_ROUND_UP(xfer->bits_per_word, 8);
+ if (n_words <= (qup->in_fifo_sz / sizeof(u32)))
return false;
- qup->use_dma = 1;
-
return true;
}
--
QUALCOMM INDIA, on behalf of Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum, hosted by The Linux Foundation
--
To unsubscribe from this list: send the line "unsubscribe linux-spi" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
WARNING: multiple messages have this Message-ID (diff)
From: Varadarajan Narayanan <varada@codeaurora.org>
To: broonie@kernel.org, robh+dt@kernel.org, mark.rutland@arm.com,
andy.gross@linaro.org, david.brown@linaro.org,
linux-spi@vger.kernel.org, devicetree@vger.kernel.org,
linux-kernel@vger.kernel.org, linux-arm-msm@vger.kernel.org,
linux-soc@vger.kernel.org
Cc: Varadarajan Narayanan <varada@codeaurora.org>
Subject: [PATCH v5 02/14] spi: qup: Setup DMA mode correctly
Date: Mon, 24 Jul 2017 13:17:13 +0530 [thread overview]
Message-ID: <1500882445-29008-3-git-send-email-varada@codeaurora.org> (raw)
In-Reply-To: <1500882445-29008-1-git-send-email-varada@codeaurora.org>
To operate in DMA mode, the buffer should be aligned and
the size of the transfer should be a multiple of block size
(for v1). And the no. of words being transferred should
be programmed in the count registers appropriately.
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Signed-off-by: Varadarajan Narayanan <varada@codeaurora.org>
---
drivers/spi/spi-qup.c | 118 +++++++++++++++++++++++---------------------------
1 file changed, 55 insertions(+), 63 deletions(-)
diff --git a/drivers/spi/spi-qup.c b/drivers/spi/spi-qup.c
index c0d4def..abe799b 100644
--- a/drivers/spi/spi-qup.c
+++ b/drivers/spi/spi-qup.c
@@ -149,11 +149,18 @@ struct spi_qup {
int rx_bytes;
int qup_v1;
- int use_dma;
+ int mode;
struct dma_slave_config rx_conf;
struct dma_slave_config tx_conf;
};
+static inline bool spi_qup_is_dma_xfer(int mode)
+{
+ if (mode == QUP_IO_M_MODE_DMOV || mode == QUP_IO_M_MODE_BAM)
+ return true;
+
+ return false;
+}
static inline bool spi_qup_is_valid_state(struct spi_qup *controller)
{
@@ -424,7 +431,7 @@ static irqreturn_t spi_qup_qup_irq(int irq, void *dev_id)
error = -EIO;
}
- if (!controller->use_dma) {
+ if (!spi_qup_is_dma_xfer(controller->mode)) {
if (opflags & QUP_OP_IN_SERVICE_FLAG)
spi_qup_fifo_read(controller, xfer);
@@ -443,34 +450,11 @@ static irqreturn_t spi_qup_qup_irq(int irq, void *dev_id)
return IRQ_HANDLED;
}
-static u32
-spi_qup_get_mode(struct spi_master *master, struct spi_transfer *xfer)
-{
- struct spi_qup *qup = spi_master_get_devdata(master);
- u32 mode;
-
- qup->w_size = 4;
-
- if (xfer->bits_per_word <= 8)
- qup->w_size = 1;
- else if (xfer->bits_per_word <= 16)
- qup->w_size = 2;
-
- qup->n_words = xfer->len / qup->w_size;
-
- if (qup->n_words <= (qup->in_fifo_sz / sizeof(u32)))
- mode = QUP_IO_M_MODE_FIFO;
- else
- mode = QUP_IO_M_MODE_BLOCK;
-
- return mode;
-}
-
/* set clock freq ... bits per word */
static int spi_qup_io_config(struct spi_device *spi, struct spi_transfer *xfer)
{
struct spi_qup *controller = spi_master_get_devdata(spi->master);
- u32 config, iomode, mode, control;
+ u32 config, iomode, control;
int ret, n_words;
if (spi->mode & SPI_LOOP && xfer->len > controller->in_fifo_sz) {
@@ -491,25 +475,30 @@ static int spi_qup_io_config(struct spi_device *spi, struct spi_transfer *xfer)
return -EIO;
}
- mode = spi_qup_get_mode(spi->master, xfer);
+ controller->w_size = DIV_ROUND_UP(xfer->bits_per_word, 8);
+ controller->n_words = xfer->len / controller->w_size;
n_words = controller->n_words;
- if (mode == QUP_IO_M_MODE_FIFO) {
+ if (n_words <= (controller->in_fifo_sz / sizeof(u32))) {
+
+ controller->mode = QUP_IO_M_MODE_FIFO;
+
writel_relaxed(n_words, controller->base + QUP_MX_READ_CNT);
writel_relaxed(n_words, controller->base + QUP_MX_WRITE_CNT);
/* must be zero for FIFO */
writel_relaxed(0, controller->base + QUP_MX_INPUT_CNT);
writel_relaxed(0, controller->base + QUP_MX_OUTPUT_CNT);
- } else if (!controller->use_dma) {
+ } else if (spi->master->can_dma &&
+ spi->master->can_dma(spi->master, spi, xfer) &&
+ spi->master->cur_msg_mapped) {
+
+ controller->mode = QUP_IO_M_MODE_BAM;
+
writel_relaxed(n_words, controller->base + QUP_MX_INPUT_CNT);
writel_relaxed(n_words, controller->base + QUP_MX_OUTPUT_CNT);
/* must be zero for BLOCK and BAM */
writel_relaxed(0, controller->base + QUP_MX_READ_CNT);
writel_relaxed(0, controller->base + QUP_MX_WRITE_CNT);
- } else {
- mode = QUP_IO_M_MODE_BAM;
- writel_relaxed(0, controller->base + QUP_MX_READ_CNT);
- writel_relaxed(0, controller->base + QUP_MX_WRITE_CNT);
if (!controller->qup_v1) {
void __iomem *input_cnt;
@@ -528,19 +517,28 @@ static int spi_qup_io_config(struct spi_device *spi, struct spi_transfer *xfer)
writel_relaxed(0, controller->base + QUP_MX_OUTPUT_CNT);
}
+ } else {
+
+ controller->mode = QUP_IO_M_MODE_BLOCK;
+
+ writel_relaxed(n_words, controller->base + QUP_MX_INPUT_CNT);
+ writel_relaxed(n_words, controller->base + QUP_MX_OUTPUT_CNT);
+ /* must be zero for BLOCK and BAM */
+ writel_relaxed(0, controller->base + QUP_MX_READ_CNT);
+ writel_relaxed(0, controller->base + QUP_MX_WRITE_CNT);
}
iomode = readl_relaxed(controller->base + QUP_IO_M_MODES);
/* Set input and output transfer mode */
iomode &= ~(QUP_IO_M_INPUT_MODE_MASK | QUP_IO_M_OUTPUT_MODE_MASK);
- if (!controller->use_dma)
+ if (!spi_qup_is_dma_xfer(controller->mode))
iomode &= ~(QUP_IO_M_PACK_EN | QUP_IO_M_UNPACK_EN);
else
iomode |= QUP_IO_M_PACK_EN | QUP_IO_M_UNPACK_EN;
- iomode |= (mode << QUP_IO_M_OUTPUT_MODE_MASK_SHIFT);
- iomode |= (mode << QUP_IO_M_INPUT_MODE_MASK_SHIFT);
+ iomode |= (controller->mode << QUP_IO_M_OUTPUT_MODE_MASK_SHIFT);
+ iomode |= (controller->mode << QUP_IO_M_INPUT_MODE_MASK_SHIFT);
writel_relaxed(iomode, controller->base + QUP_IO_M_MODES);
@@ -581,7 +579,7 @@ static int spi_qup_io_config(struct spi_device *spi, struct spi_transfer *xfer)
config |= xfer->bits_per_word - 1;
config |= QUP_CONFIG_SPI_MODE;
- if (controller->use_dma) {
+ if (spi_qup_is_dma_xfer(controller->mode)) {
if (!xfer->tx_buf)
config |= QUP_CONFIG_NO_OUTPUT;
if (!xfer->rx_buf)
@@ -599,7 +597,7 @@ static int spi_qup_io_config(struct spi_device *spi, struct spi_transfer *xfer)
* status change in BAM mode
*/
- if (mode == QUP_IO_M_MODE_BAM)
+ if (spi_qup_is_dma_xfer(controller->mode))
mask = QUP_OP_IN_SERVICE_FLAG | QUP_OP_OUT_SERVICE_FLAG;
writel_relaxed(mask, controller->base + QUP_OPERATIONAL_MASK);
@@ -633,7 +631,7 @@ static int spi_qup_transfer_one(struct spi_master *master,
controller->tx_bytes = 0;
spin_unlock_irqrestore(&controller->lock, flags);
- if (controller->use_dma)
+ if (spi_qup_is_dma_xfer(controller->mode))
ret = spi_qup_do_dma(master, xfer);
else
ret = spi_qup_do_pio(master, xfer);
@@ -641,14 +639,6 @@ static int spi_qup_transfer_one(struct spi_master *master,
if (ret)
goto exit;
- if (spi_qup_set_state(controller, QUP_STATE_RUN)) {
- dev_warn(controller->dev, "cannot set EXECUTE state\n");
- goto exit;
- }
-
- if (!wait_for_completion_timeout(&controller->done, timeout))
- ret = -ETIMEDOUT;
-
exit:
spi_qup_set_state(controller, QUP_STATE_RESET);
spin_lock_irqsave(&controller->lock, flags);
@@ -657,7 +647,7 @@ static int spi_qup_transfer_one(struct spi_master *master,
ret = controller->error;
spin_unlock_irqrestore(&controller->lock, flags);
- if (ret && controller->use_dma)
+ if (ret && spi_qup_is_dma_xfer(controller->mode))
spi_qup_dma_terminate(master, xfer);
return ret;
@@ -668,26 +658,28 @@ static bool spi_qup_can_dma(struct spi_master *master, struct spi_device *spi,
{
struct spi_qup *qup = spi_master_get_devdata(master);
size_t dma_align = dma_get_cache_alignment();
- u32 mode;
-
- qup->use_dma = 0;
+ int n_words;
- if (xfer->rx_buf && (xfer->len % qup->in_blk_sz ||
- IS_ERR_OR_NULL(master->dma_rx) ||
- !IS_ALIGNED((size_t)xfer->rx_buf, dma_align)))
- return false;
+ if (xfer->rx_buf) {
+ if (!IS_ALIGNED((size_t)xfer->rx_buf, dma_align) ||
+ IS_ERR_OR_NULL(master->dma_rx))
+ return false;
+ if (qup->qup_v1 && (xfer->len % qup->in_blk_sz))
+ return false;
+ }
- if (xfer->tx_buf && (xfer->len % qup->out_blk_sz ||
- IS_ERR_OR_NULL(master->dma_tx) ||
- !IS_ALIGNED((size_t)xfer->tx_buf, dma_align)))
- return false;
+ if (xfer->tx_buf) {
+ if (!IS_ALIGNED((size_t)xfer->tx_buf, dma_align) ||
+ IS_ERR_OR_NULL(master->dma_tx))
+ return false;
+ if (qup->qup_v1 && (xfer->len % qup->out_blk_sz))
+ return false;
+ }
- mode = spi_qup_get_mode(master, xfer);
- if (mode == QUP_IO_M_MODE_FIFO)
+ n_words = xfer->len / DIV_ROUND_UP(xfer->bits_per_word, 8);
+ if (n_words <= (qup->in_fifo_sz / sizeof(u32)))
return false;
- qup->use_dma = 1;
-
return true;
}
--
QUALCOMM INDIA, on behalf of Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum, hosted by The Linux Foundation
next prev parent reply other threads:[~2017-07-24 7:47 UTC|newest]
Thread overview: 43+ messages / expand[flat|nested] mbox.gz Atom feed top
2017-07-24 7:47 [PATCH v5 00/14] spi: qup: Fixes and add support for >64k transfers Varadarajan Narayanan
2017-07-24 7:47 ` [PATCH v5 01/14] spi: qup: Enable chip select support Varadarajan Narayanan
[not found] ` <1500882445-29008-1-git-send-email-varada-sgV2jX0FEOL9JmXXK+q4OQ@public.gmane.org>
2017-07-24 7:47 ` Varadarajan Narayanan [this message]
2017-07-24 7:47 ` [PATCH v5 02/14] spi: qup: Setup DMA mode correctly Varadarajan Narayanan
2017-07-24 7:47 ` [PATCH v5 03/14] spi: qup: Add completion timeout Varadarajan Narayanan
2017-07-24 7:47 ` Varadarajan Narayanan
2017-07-27 8:30 ` kbuild test robot
2017-07-27 8:30 ` kbuild test robot
2017-07-24 7:47 ` [PATCH v5 05/14] spi: qup: Fix error handling in spi_qup_prep_sg Varadarajan Narayanan
2017-07-24 7:47 ` Varadarajan Narayanan
2017-08-08 11:18 ` Applied "spi: qup: Fix error handling in spi_qup_prep_sg" to the spi tree Mark Brown
2017-08-08 11:18 ` Mark Brown
2017-07-24 7:47 ` [PATCH v5 07/14] spi: qup: Do block sized read/write in block mode Varadarajan Narayanan
2017-07-24 7:47 ` Varadarajan Narayanan
2017-08-08 11:18 ` Applied "spi: qup: Do block sized read/write in block mode" to the spi tree Mark Brown
2017-08-08 11:18 ` Mark Brown
2017-07-24 7:47 ` [PATCH v5 09/14] spi: qup: call io_config in mode specific function Varadarajan Narayanan
2017-07-24 7:47 ` Varadarajan Narayanan
2017-07-24 7:47 ` [PATCH v5 10/14] spi: qup: allow block mode to generate multiple transactions Varadarajan Narayanan
2017-07-24 7:47 ` Varadarajan Narayanan
2017-08-08 11:18 ` Applied "spi: qup: allow block mode to generate multiple transactions" to the spi tree Mark Brown
2017-08-08 11:18 ` Mark Brown
2017-07-24 7:47 ` [PATCH v5 11/14] spi: qup: refactor spi_qup_prep_sg Varadarajan Narayanan
2017-07-24 7:47 ` Varadarajan Narayanan
2017-08-08 11:18 ` Applied "spi: qup: refactor spi_qup_prep_sg" to the spi tree Mark Brown
2017-08-08 11:18 ` Mark Brown
2017-07-24 7:47 ` [PATCH v5 12/14] spi: qup: allow multiple DMA transactions per spi xfer Varadarajan Narayanan
2017-07-24 7:47 ` Varadarajan Narayanan
2017-07-24 7:47 ` [PATCH v5 04/14] spi: qup: Place the QUP in run mode before DMA Varadarajan Narayanan
2017-08-08 11:18 ` Applied "spi: qup: Place the QUP in run mode before DMA" to the spi tree Mark Brown
2017-08-08 11:18 ` Mark Brown
2017-07-24 7:47 ` [PATCH v5 06/14] spi: qup: Fix transaction done signaling Varadarajan Narayanan
2017-07-24 7:47 ` [PATCH v5 08/14] spi: qup: refactor spi_qup_io_config into two functions Varadarajan Narayanan
2017-08-08 11:18 ` Applied "spi: qup: refactor spi_qup_io_config into two functions" to the spi tree Mark Brown
2017-08-08 11:18 ` Mark Brown
2017-07-24 7:47 ` [PATCH v5 13/14] spi: qup: Ensure done detection Varadarajan Narayanan
2017-07-24 7:47 ` [PATCH v5 14/14] spi: qup: Fix QUP version identify method Varadarajan Narayanan
[not found] ` <1500882445-29008-15-git-send-email-varada-sgV2jX0FEOL9JmXXK+q4OQ@public.gmane.org>
2017-07-25 2:52 ` kbuild test robot
2017-07-25 2:52 ` kbuild test robot
2017-07-25 2:52 ` kbuild test robot
2017-08-08 11:17 ` Applied "spi: qup: Fix QUP version identify method" to the spi tree Mark Brown
2017-08-08 11:17 ` Mark Brown
2017-08-08 11:17 ` Mark Brown
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1500882445-29008-3-git-send-email-varada@codeaurora.org \
--to=varada-sgv2jx0feol9jmxxk+q4oq@public.gmane.org \
--cc=andy.gross-QSEj5FYQhm4dnm+yROfE0A@public.gmane.org \
--cc=broonie-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org \
--cc=david.brown-QSEj5FYQhm4dnm+yROfE0A@public.gmane.org \
--cc=devicetree-u79uwXL29TY76Z2rM5mHXA@public.gmane.org \
--cc=linux-arm-msm-u79uwXL29TY76Z2rM5mHXA@public.gmane.org \
--cc=linux-kernel-u79uwXL29TY76Z2rM5mHXA@public.gmane.org \
--cc=linux-soc-u79uwXL29TY76Z2rM5mHXA@public.gmane.org \
--cc=linux-spi-u79uwXL29TY76Z2rM5mHXA@public.gmane.org \
--cc=mark.rutland-5wv7dgnIgG8@public.gmane.org \
--cc=robh+dt-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.