From: Neil Armstrong <narmstrong@baylibre.com>
To: khilman@baylibre.com
Cc: Neil Armstrong <narmstrong@baylibre.com>,
linux-amlogic@lists.infradead.org,
linux-arm-kernel@lists.infradead.org,
linux-kernel@vger.kernel.org
Subject: [PATCH] ARM64: dts: meson-gxl-libretech-cc: Add GPIO lines names
Date: Fri, 4 Aug 2017 15:38:04 +0200 [thread overview]
Message-ID: <1501853884-32680-1-git-send-email-narmstrong@baylibre.com> (raw)
This patch describes the GPIO lines usage on the LibreTech CC board.
This is useful in the debugfs gpio file and using the cdev gpio API.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
---
.../dts/amlogic/meson-gxl-s905x-libretech-cc.dts | 57 ++++++++++++++++++++++
1 file changed, 57 insertions(+)
diff --git a/arch/arm64/boot/dts/amlogic/meson-gxl-s905x-libretech-cc.dts b/arch/arm64/boot/dts/amlogic/meson-gxl-s905x-libretech-cc.dts
index 266fbcf..80ecd71 100644
--- a/arch/arm64/boot/dts/amlogic/meson-gxl-s905x-libretech-cc.dts
+++ b/arch/arm64/boot/dts/amlogic/meson-gxl-s905x-libretech-cc.dts
@@ -129,6 +129,63 @@
};
};
+&pinctrl_aobus {
+ gpio-line-names = "UART TX",
+ "UART RX",
+ "Blue LED",
+ "SDCard Voltage Switch",
+ "7J1 Header Pin5",
+ "7J1 Header Pin3",
+ "7J1 Header Pin12",
+ "IR In",
+ "9J3 Switch HDMI CEC/7J1 Header Pin11",
+ "7J1 Header Pin13";
+};
+
+&pinctrl_periphs {
+ gpio-line-names = /* Bank GPIOZ */
+ "", "", "", "", "", "", "",
+ "", "", "", "", "", "", "",
+ "Eth Link LED", "Eth Activity LED",
+ /* Bank GPIOH */
+ "HDMI HPD", "HDMI SDA", "HDMI SCL",
+ "HDMI_5V_EN", "9J1 Header Pin2",
+ "Analog Audio Mute",
+ "2J3 Header Pin6",
+ "2J3 Header Pin5",
+ "2J3 Header Pin4",
+ "2J3 Header Pin3",
+ /* Bank BOOT */
+ "eMMC D0", "eMMC D1", "eMMC D2", "eMMC D3",
+ "eMMC D4", "eMMC D5", "eMMC D6", "eMMC D7",
+ "eMMC Clk", "eMMC Reset", "eMMC CMD",
+ "ALT BOOT MODE", "", "", "", "eMMC Data Strobe",
+ /* Bank CARD */
+ "SDCard D1", "SDCard D0", "SDCard CLK", "SDCard CMD",
+ "SDCard D3", "SDCard D2", "SDCard Det",
+ /* Bank GPIODV */
+ "", "", "", "", "", "", "", "", "", "", "", "",
+ "", "", "", "", "", "", "", "", "", "", "", "",
+ "Green LED", "VCCK Enable",
+ "7J1 Header Pin27", "7J1 Header Pin28",
+ "VCCK Regulator", "VDDEE Regulator",
+ /* Bank GPIOX */
+ "7J1 Header Pin22", "7J1 Header Pin26",
+ "7J1 Header Pin36", "7J1 Header Pin38",
+ "7J1 Header Pin40", "7J1 Header Pin37",
+ "7J1 Header Pin33", "7J1 Header Pin35",
+ "7J1 Header Pin19", "7J1 Header Pin21",
+ "7J1 Header Pin24", "7J1 Header Pin23",
+ "7J1 Header Pin8", "7J1 Header Pin10",
+ "7J1 Header Pin16", "7J1 Header Pin18",
+ "7J1 Header Pin32", "7J1 Header Pin29",
+ "7J1 Header Pin31",
+ /* Bank GPIOCLK */
+ "7J1 Header Pin7", "",
+ /* GPIO_TEST_N */
+ "7J1 Header Pin15";
+};
+
/* SD card */
&sd_emmc_b {
status = "okay";
--
1.9.1
WARNING: multiple messages have this Message-ID (diff)
From: narmstrong@baylibre.com (Neil Armstrong)
To: linux-arm-kernel@lists.infradead.org
Subject: [PATCH] ARM64: dts: meson-gxl-libretech-cc: Add GPIO lines names
Date: Fri, 4 Aug 2017 15:38:04 +0200 [thread overview]
Message-ID: <1501853884-32680-1-git-send-email-narmstrong@baylibre.com> (raw)
This patch describes the GPIO lines usage on the LibreTech CC board.
This is useful in the debugfs gpio file and using the cdev gpio API.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
---
.../dts/amlogic/meson-gxl-s905x-libretech-cc.dts | 57 ++++++++++++++++++++++
1 file changed, 57 insertions(+)
diff --git a/arch/arm64/boot/dts/amlogic/meson-gxl-s905x-libretech-cc.dts b/arch/arm64/boot/dts/amlogic/meson-gxl-s905x-libretech-cc.dts
index 266fbcf..80ecd71 100644
--- a/arch/arm64/boot/dts/amlogic/meson-gxl-s905x-libretech-cc.dts
+++ b/arch/arm64/boot/dts/amlogic/meson-gxl-s905x-libretech-cc.dts
@@ -129,6 +129,63 @@
};
};
+&pinctrl_aobus {
+ gpio-line-names = "UART TX",
+ "UART RX",
+ "Blue LED",
+ "SDCard Voltage Switch",
+ "7J1 Header Pin5",
+ "7J1 Header Pin3",
+ "7J1 Header Pin12",
+ "IR In",
+ "9J3 Switch HDMI CEC/7J1 Header Pin11",
+ "7J1 Header Pin13";
+};
+
+&pinctrl_periphs {
+ gpio-line-names = /* Bank GPIOZ */
+ "", "", "", "", "", "", "",
+ "", "", "", "", "", "", "",
+ "Eth Link LED", "Eth Activity LED",
+ /* Bank GPIOH */
+ "HDMI HPD", "HDMI SDA", "HDMI SCL",
+ "HDMI_5V_EN", "9J1 Header Pin2",
+ "Analog Audio Mute",
+ "2J3 Header Pin6",
+ "2J3 Header Pin5",
+ "2J3 Header Pin4",
+ "2J3 Header Pin3",
+ /* Bank BOOT */
+ "eMMC D0", "eMMC D1", "eMMC D2", "eMMC D3",
+ "eMMC D4", "eMMC D5", "eMMC D6", "eMMC D7",
+ "eMMC Clk", "eMMC Reset", "eMMC CMD",
+ "ALT BOOT MODE", "", "", "", "eMMC Data Strobe",
+ /* Bank CARD */
+ "SDCard D1", "SDCard D0", "SDCard CLK", "SDCard CMD",
+ "SDCard D3", "SDCard D2", "SDCard Det",
+ /* Bank GPIODV */
+ "", "", "", "", "", "", "", "", "", "", "", "",
+ "", "", "", "", "", "", "", "", "", "", "", "",
+ "Green LED", "VCCK Enable",
+ "7J1 Header Pin27", "7J1 Header Pin28",
+ "VCCK Regulator", "VDDEE Regulator",
+ /* Bank GPIOX */
+ "7J1 Header Pin22", "7J1 Header Pin26",
+ "7J1 Header Pin36", "7J1 Header Pin38",
+ "7J1 Header Pin40", "7J1 Header Pin37",
+ "7J1 Header Pin33", "7J1 Header Pin35",
+ "7J1 Header Pin19", "7J1 Header Pin21",
+ "7J1 Header Pin24", "7J1 Header Pin23",
+ "7J1 Header Pin8", "7J1 Header Pin10",
+ "7J1 Header Pin16", "7J1 Header Pin18",
+ "7J1 Header Pin32", "7J1 Header Pin29",
+ "7J1 Header Pin31",
+ /* Bank GPIOCLK */
+ "7J1 Header Pin7", "",
+ /* GPIO_TEST_N */
+ "7J1 Header Pin15";
+};
+
/* SD card */
&sd_emmc_b {
status = "okay";
--
1.9.1
WARNING: multiple messages have this Message-ID (diff)
From: narmstrong@baylibre.com (Neil Armstrong)
To: linus-amlogic@lists.infradead.org
Subject: [PATCH] ARM64: dts: meson-gxl-libretech-cc: Add GPIO lines names
Date: Fri, 4 Aug 2017 15:38:04 +0200 [thread overview]
Message-ID: <1501853884-32680-1-git-send-email-narmstrong@baylibre.com> (raw)
This patch describes the GPIO lines usage on the LibreTech CC board.
This is useful in the debugfs gpio file and using the cdev gpio API.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
---
.../dts/amlogic/meson-gxl-s905x-libretech-cc.dts | 57 ++++++++++++++++++++++
1 file changed, 57 insertions(+)
diff --git a/arch/arm64/boot/dts/amlogic/meson-gxl-s905x-libretech-cc.dts b/arch/arm64/boot/dts/amlogic/meson-gxl-s905x-libretech-cc.dts
index 266fbcf..80ecd71 100644
--- a/arch/arm64/boot/dts/amlogic/meson-gxl-s905x-libretech-cc.dts
+++ b/arch/arm64/boot/dts/amlogic/meson-gxl-s905x-libretech-cc.dts
@@ -129,6 +129,63 @@
};
};
+&pinctrl_aobus {
+ gpio-line-names = "UART TX",
+ "UART RX",
+ "Blue LED",
+ "SDCard Voltage Switch",
+ "7J1 Header Pin5",
+ "7J1 Header Pin3",
+ "7J1 Header Pin12",
+ "IR In",
+ "9J3 Switch HDMI CEC/7J1 Header Pin11",
+ "7J1 Header Pin13";
+};
+
+&pinctrl_periphs {
+ gpio-line-names = /* Bank GPIOZ */
+ "", "", "", "", "", "", "",
+ "", "", "", "", "", "", "",
+ "Eth Link LED", "Eth Activity LED",
+ /* Bank GPIOH */
+ "HDMI HPD", "HDMI SDA", "HDMI SCL",
+ "HDMI_5V_EN", "9J1 Header Pin2",
+ "Analog Audio Mute",
+ "2J3 Header Pin6",
+ "2J3 Header Pin5",
+ "2J3 Header Pin4",
+ "2J3 Header Pin3",
+ /* Bank BOOT */
+ "eMMC D0", "eMMC D1", "eMMC D2", "eMMC D3",
+ "eMMC D4", "eMMC D5", "eMMC D6", "eMMC D7",
+ "eMMC Clk", "eMMC Reset", "eMMC CMD",
+ "ALT BOOT MODE", "", "", "", "eMMC Data Strobe",
+ /* Bank CARD */
+ "SDCard D1", "SDCard D0", "SDCard CLK", "SDCard CMD",
+ "SDCard D3", "SDCard D2", "SDCard Det",
+ /* Bank GPIODV */
+ "", "", "", "", "", "", "", "", "", "", "", "",
+ "", "", "", "", "", "", "", "", "", "", "", "",
+ "Green LED", "VCCK Enable",
+ "7J1 Header Pin27", "7J1 Header Pin28",
+ "VCCK Regulator", "VDDEE Regulator",
+ /* Bank GPIOX */
+ "7J1 Header Pin22", "7J1 Header Pin26",
+ "7J1 Header Pin36", "7J1 Header Pin38",
+ "7J1 Header Pin40", "7J1 Header Pin37",
+ "7J1 Header Pin33", "7J1 Header Pin35",
+ "7J1 Header Pin19", "7J1 Header Pin21",
+ "7J1 Header Pin24", "7J1 Header Pin23",
+ "7J1 Header Pin8", "7J1 Header Pin10",
+ "7J1 Header Pin16", "7J1 Header Pin18",
+ "7J1 Header Pin32", "7J1 Header Pin29",
+ "7J1 Header Pin31",
+ /* Bank GPIOCLK */
+ "7J1 Header Pin7", "",
+ /* GPIO_TEST_N */
+ "7J1 Header Pin15";
+};
+
/* SD card */
&sd_emmc_b {
status = "okay";
--
1.9.1
next reply other threads:[~2017-08-04 13:38 UTC|newest]
Thread overview: 6+ messages / expand[flat|nested] mbox.gz Atom feed top
2017-08-04 13:38 Neil Armstrong [this message]
2017-08-04 13:38 ` [PATCH] ARM64: dts: meson-gxl-libretech-cc: Add GPIO lines names Neil Armstrong
2017-08-04 13:38 ` Neil Armstrong
2017-08-25 0:08 ` Kevin Hilman
2017-08-25 0:08 ` Kevin Hilman
2017-08-25 0:08 ` Kevin Hilman
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1501853884-32680-1-git-send-email-narmstrong@baylibre.com \
--to=narmstrong@baylibre.com \
--cc=khilman@baylibre.com \
--cc=linux-amlogic@lists.infradead.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.