From: Faiz Abbas <faiz_abbas@ti.com> To: <kishon@ti.com> Cc: <bhelgaas@google.com>, <linux-omap@vger.kernel.org>, <linux-pci@vger.kernel.org>, <linux-kernel@vger.kernel.org>, <faiz_abbas@ti.com> Subject: [PATCH v2] dwc: dra7xx: Print link state to console for debug Date: Thu, 19 Oct 2017 18:13:29 +0530 [thread overview] Message-ID: <1508417009-30869-1-git-send-email-faiz_abbas@ti.com> (raw) Enable support for printing the LTSSM link state for debugging PCI when link is down. Signed-off-by: Faiz Abbas <faiz_abbas@ti.com> --- v2: 1. Changed dev_err() to dev_dbg() 2. Changed static char array to static const char * const 3. format changes drivers/pci/dwc/pci-dra7xx.c | 48 ++++++++++++++++++++++++++++++++++++++++++++ 1 file changed, 48 insertions(+) diff --git a/drivers/pci/dwc/pci-dra7xx.c b/drivers/pci/dwc/pci-dra7xx.c index 34427a6..0e70e77 100644 --- a/drivers/pci/dwc/pci-dra7xx.c +++ b/drivers/pci/dwc/pci-dra7xx.c @@ -98,6 +98,45 @@ struct dra7xx_pcie_of_data { #define to_dra7xx_pcie(x) dev_get_drvdata((x)->dev) +static const char * const state[] = { + "DETECT_QUIET", + "DETECT_ACT", + "POLL_ACTIVE", + "POLL_COMPLIANCE", + "POLL_CONFIG", + "PRE_DETECT_QUIET", + "DETECT_WAIT", + "CFG_LINKWD_START", + "CFG_LINKWD_ACEPT", + "CFG_LANENUM_WAIT", + "CFG_LANENUM_ACEPT", + "CFG_COMPLETE", + "CFG_IDLE", + "RCVRY_LOCK", + "RCVRY_SPEED", + "RCVRY_RCVRCFG", + "RCVRY_IDLE", + "L0", + "L0S", + "L123_SEND_EIDLE", + "L1_IDLE", + "L2_IDLE", + "L2_WAKE", + "DISABLED_ENTRY", + "DISABLED_IDLE", + "DISABLED", + "LPBK_ENTRY", + "LPBK_ACTIVE", + "LPBK_EXIT", + "LPBK_EXIT_TIMEOUT", + "HOT_RESET_ENTRY", + "HOT_RESET", + "RCVRY_EQ0", + "RCVRY_EQ1", + "RCVRY_EQ2", + "RCVRY_EQ3" +}; + static inline u32 dra7xx_pcie_readl(struct dra7xx_pcie *pcie, u32 offset) { return readl(pcie->base + offset); @@ -118,6 +157,15 @@ static int dra7xx_pcie_link_up(struct dw_pcie *pci) { struct dra7xx_pcie *dra7xx = to_dra7xx_pcie(pci); u32 reg = dra7xx_pcie_readl(dra7xx, PCIECTRL_DRA7XX_CONF_PHY_CS); + u32 cmd_reg; + u32 ltssm_state; + + if (!(reg & LINK_UP)) { + cmd_reg = dra7xx_pcie_readl(dra7xx, + PCIECTRL_DRA7XX_CONF_DEVICE_CMD); + ltssm_state = (cmd_reg & GENMASK(7, 2)) >> 2; + dev_dbg(pci->dev, "Link state:%s\n", state[ltssm_state]); + } return !!(reg & LINK_UP); } -- 2.7.4
WARNING: multiple messages have this Message-ID (diff)
From: Faiz Abbas <faiz_abbas@ti.com> To: kishon@ti.com Cc: bhelgaas@google.com, linux-omap@vger.kernel.org, linux-pci@vger.kernel.org, linux-kernel@vger.kernel.org, faiz_abbas@ti.com Subject: [PATCH v2] dwc: dra7xx: Print link state to console for debug Date: Thu, 19 Oct 2017 18:13:29 +0530 [thread overview] Message-ID: <1508417009-30869-1-git-send-email-faiz_abbas@ti.com> (raw) Enable support for printing the LTSSM link state for debugging PCI when link is down. Signed-off-by: Faiz Abbas <faiz_abbas@ti.com> --- v2: 1. Changed dev_err() to dev_dbg() 2. Changed static char array to static const char * const 3. format changes drivers/pci/dwc/pci-dra7xx.c | 48 ++++++++++++++++++++++++++++++++++++++++++++ 1 file changed, 48 insertions(+) diff --git a/drivers/pci/dwc/pci-dra7xx.c b/drivers/pci/dwc/pci-dra7xx.c index 34427a6..0e70e77 100644 --- a/drivers/pci/dwc/pci-dra7xx.c +++ b/drivers/pci/dwc/pci-dra7xx.c @@ -98,6 +98,45 @@ struct dra7xx_pcie_of_data { #define to_dra7xx_pcie(x) dev_get_drvdata((x)->dev) +static const char * const state[] = { + "DETECT_QUIET", + "DETECT_ACT", + "POLL_ACTIVE", + "POLL_COMPLIANCE", + "POLL_CONFIG", + "PRE_DETECT_QUIET", + "DETECT_WAIT", + "CFG_LINKWD_START", + "CFG_LINKWD_ACEPT", + "CFG_LANENUM_WAIT", + "CFG_LANENUM_ACEPT", + "CFG_COMPLETE", + "CFG_IDLE", + "RCVRY_LOCK", + "RCVRY_SPEED", + "RCVRY_RCVRCFG", + "RCVRY_IDLE", + "L0", + "L0S", + "L123_SEND_EIDLE", + "L1_IDLE", + "L2_IDLE", + "L2_WAKE", + "DISABLED_ENTRY", + "DISABLED_IDLE", + "DISABLED", + "LPBK_ENTRY", + "LPBK_ACTIVE", + "LPBK_EXIT", + "LPBK_EXIT_TIMEOUT", + "HOT_RESET_ENTRY", + "HOT_RESET", + "RCVRY_EQ0", + "RCVRY_EQ1", + "RCVRY_EQ2", + "RCVRY_EQ3" +}; + static inline u32 dra7xx_pcie_readl(struct dra7xx_pcie *pcie, u32 offset) { return readl(pcie->base + offset); @@ -118,6 +157,15 @@ static int dra7xx_pcie_link_up(struct dw_pcie *pci) { struct dra7xx_pcie *dra7xx = to_dra7xx_pcie(pci); u32 reg = dra7xx_pcie_readl(dra7xx, PCIECTRL_DRA7XX_CONF_PHY_CS); + u32 cmd_reg; + u32 ltssm_state; + + if (!(reg & LINK_UP)) { + cmd_reg = dra7xx_pcie_readl(dra7xx, + PCIECTRL_DRA7XX_CONF_DEVICE_CMD); + ltssm_state = (cmd_reg & GENMASK(7, 2)) >> 2; + dev_dbg(pci->dev, "Link state:%s\n", state[ltssm_state]); + } return !!(reg & LINK_UP); } -- 2.7.4
next reply other threads:[~2017-10-19 12:43 UTC|newest] Thread overview: 19+ messages / expand[flat|nested] mbox.gz Atom feed top 2017-10-19 12:43 Faiz Abbas [this message] 2017-10-19 12:43 ` [PATCH v2] dwc: dra7xx: Print link state to console for debug Faiz Abbas 2017-10-19 13:08 ` Faiz Abbas 2017-10-19 13:08 ` Faiz Abbas 2017-10-19 13:26 ` David Laight 2017-10-19 13:26 ` David Laight 2017-10-26 7:59 ` Faiz Abbas 2017-10-30 8:48 ` Faiz Abbas 2017-11-06 2:56 ` Faiz Abbas 2017-10-20 23:09 ` Bjorn Helgaas 2017-10-23 10:29 ` Faiz Abbas 2017-10-23 10:29 ` Faiz Abbas 2017-10-23 14:04 ` Bjorn Helgaas 2017-10-24 6:18 ` Kishon Vijay Abraham I 2017-10-24 6:18 ` Kishon Vijay Abraham I 2017-10-24 19:59 ` Bjorn Helgaas 2017-10-25 8:21 ` Faiz Abbas 2017-10-25 8:21 ` Faiz Abbas 2017-10-25 13:23 ` Bjorn Helgaas
Reply instructions: You may reply publicly to this message via plain-text email using any one of the following methods: * Save the following mbox file, import it into your mail client, and reply-to-all from there: mbox Avoid top-posting and favor interleaved quoting: https://en.wikipedia.org/wiki/Posting_style#Interleaved_style * Reply using the --to, --cc, and --in-reply-to switches of git-send-email(1): git send-email \ --in-reply-to=1508417009-30869-1-git-send-email-faiz_abbas@ti.com \ --to=faiz_abbas@ti.com \ --cc=bhelgaas@google.com \ --cc=kishon@ti.com \ --cc=linux-kernel@vger.kernel.org \ --cc=linux-omap@vger.kernel.org \ --cc=linux-pci@vger.kernel.org \ /path/to/YOUR_REPLY https://kernel.org/pub/software/scm/git/docs/git-send-email.html * If your mail client supports setting the In-Reply-To header via mailto: links, try the mailto: linkBe sure your reply has a Subject: header at the top and a blank line before the message body.
This is an external index of several public inboxes, see mirroring instructions on how to clone and mirror all data and code used by this external index.