From: Stefan Riedmueller <s.riedmueller@phytec.de>
To: shawnguo@kernel.org, kernel@pengutronix.de, fabio.estevam@nxp.com
Cc: mark.rutland@arm.com, devicetree@vger.kernel.org,
Stefan Riedmueller <s.riedmueller@phytec.de>,
Christoph Fritz <chf.fritz@googlemail.com>,
robh+dt@kernel.org, Christian Hemp <c.hemp@phytec.de>,
Stefan Christ <s.christ@phytec.de>,
linux-arm-kernel@lists.infradead.org
Subject: [PATCH 1/6] ARM: dts: imx6: Add initial support for phyCORE-i.MX 6 SOM
Date: Tue, 19 Dec 2017 16:49:43 +0100 [thread overview]
Message-ID: <1513698588-13325-2-git-send-email-s.riedmueller@phytec.de> (raw)
In-Reply-To: <1513698588-13325-1-git-send-email-s.riedmueller@phytec.de>
This patch adds basic support for PHYTEC phyCORE-i.MX 6 SOM with i.MX
6Quad/Dual or i.MX 6DualLight/Solo.
Signed-off-by: Christian Hemp <c.hemp@phytec.de>
Signed-off-by: Stefan Christ <s.christ@phytec.de>
Signed-off-by: Christoph Fritz <chf.fritz@googlemail.com>
Signed-off-by: Stefan Riedmueller <s.riedmueller@phytec.de>
---
arch/arm/boot/dts/imx6qdl-phytec-phycore-som.dtsi | 282 ++++++++++++++++++++++
1 file changed, 282 insertions(+)
create mode 100644 arch/arm/boot/dts/imx6qdl-phytec-phycore-som.dtsi
diff --git a/arch/arm/boot/dts/imx6qdl-phytec-phycore-som.dtsi b/arch/arm/boot/dts/imx6qdl-phytec-phycore-som.dtsi
new file mode 100644
index 0000000..5283f0d
--- /dev/null
+++ b/arch/arm/boot/dts/imx6qdl-phytec-phycore-som.dtsi
@@ -0,0 +1,282 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (C) 2017 PHYTEC Messtechnik GmbH
+ * Author: Christian Hemp <c.hemp@phytec.de>
+ */
+
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+ model = "PHYTEC phyCORE-i.MX 6";
+ compatible = "phytec,imx6qdl-pcm058", "fsl,imx6qdl";
+
+ aliases {
+ ipu0 = &ipu1;
+ rtc1 = &da9062_rtc;
+ rtc2 = &snvs_rtc;
+ };
+
+ /*
+ * Set the minimum memory size here and
+ * let the bootloader set the real size.
+ */
+ memory {
+ reg = <0x10000000 0x8000000>;
+ };
+
+ gpio_leds_som: somleds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_gpioleds_som>;
+
+ som_green {
+ label = "phycore:green";
+ gpios = <&gpio1 4 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "heartbeat";
+ };
+ };
+};
+
+&ecspi1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ecspi1>;
+ cs-gpios = <&gpio3 19 GPIO_ACTIVE_LOW>;
+ status = "okay";
+
+ flash: flash@0 {
+ compatible = "m25p80";
+ spi-max-frequency = <20000000>;
+ reg = <0>;
+ status = "disabled";
+ };
+};
+
+&fec {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_enet>;
+ phy-handle = <ðphy>;
+ phy-mode = "rgmii";
+ phy-supply = <&vdd_eth_io>;
+ phy-reset-gpios = <&gpio1 14 GPIO_ACTIVE_LOW>;
+ status = "disabled";
+
+ mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ethphy: ethernet-phy@3 {
+ reg = <3>;
+ txc-skew-ps = <1680>;
+ rxc-skew-ps = <1860>;
+ };
+ };
+};
+
+&gpmi {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_gpmi_nand>;
+ nand-on-flash-bbt;
+ status = "disabled";
+};
+
+&i2c3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c3>;
+ clock-frequency = <400000>;
+ status = "okay";
+
+ eeprom: eeprom@50 {
+ compatible = "cat,24c32";
+ reg = <0x50>;
+ };
+
+ pmic0: pmic@58 {
+ compatible = "dlg,da9062";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pmic>;
+ reg = <0x58>;
+ interrupt-parent = <&gpio1>;
+ interrupts = <2 IRQ_TYPE_LEVEL_LOW>;
+ interrupt-controller;
+
+ da9062_rtc: rtc {
+ compatible = "dlg,da9062-rtc";
+ };
+
+ da9062_wdt: watchdog {
+ compatible = "dlg,da9062-watchdog";
+ };
+
+ da9062_reg: regulators {
+ vdd_arm: buck1 {
+ regulator-name = "vdd_arm";
+ regulator-min-microvolt = <730000>;
+ regulator-max-microvolt = <1380000>;
+ regulator-always-on;
+ };
+
+ vdd_soc: buck2 {
+ regulator-name = "vdd_soc";
+ regulator-min-microvolt = <730000>;
+ regulator-max-microvolt = <1380000>;
+ regulator-always-on;
+ };
+
+ vdd_ddr3_1p5: buck3 {
+ regulator-name = "vdd_ddr3";
+ regulator-min-microvolt = <1500000>;
+ regulator-max-microvolt = <1500000>;
+ regulator-always-on;
+ };
+
+ vdd_eth_1p2: buck4 {
+ regulator-name = "vdd_eth";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-always-on;
+ };
+
+ vdd_snvs: ldo1 {
+ regulator-name = "vdd_snvs";
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-always-on;
+ };
+
+ vdd_high: ldo2 {
+ regulator-name = "vdd_high";
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-always-on;
+ };
+
+ vdd_eth_io: ldo3 {
+ regulator-name = "vdd_eth_io";
+ regulator-min-microvolt = <2500000>;
+ regulator-max-microvolt = <2500000>;
+ };
+
+ vdd_emmc_1p8: ldo4 {
+ regulator-name = "vdd_emmc";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+ };
+ };
+};
+
+®_arm {
+ vin-supply = <&vdd_arm>;
+};
+
+®_pu {
+ vin-supply = <&vdd_soc>;
+};
+
+®_soc {
+ vin-supply = <&vdd_soc>;
+};
+
+&snvs_poweroff {
+ status = "okay";
+};
+
+&usdhc4 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usdhc4>;
+ bus-width = <8>;
+ non-removable;
+ vmmc-supply = <&vdd_emmc_1p8>;
+ status = "disabled";
+};
+
+&iomuxc {
+ pinctrl_enet: enetgrp {
+ fsl,pins = <
+ MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x1b0b0
+ MX6QDL_PAD_ENET_MDC__ENET_MDC 0x1b0b0
+ MX6QDL_PAD_RGMII_TXC__RGMII_TXC 0x1b0b0
+ MX6QDL_PAD_RGMII_TD0__RGMII_TD0 0x1b0b0
+ MX6QDL_PAD_RGMII_TD1__RGMII_TD1 0x1b0b0
+ MX6QDL_PAD_RGMII_TD2__RGMII_TD2 0x1b0b0
+ MX6QDL_PAD_RGMII_TD3__RGMII_TD3 0x1b0b0
+ MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL 0x1b0b0
+ MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK 0x1b0b0
+ MX6QDL_PAD_RGMII_RXC__RGMII_RXC 0x1b0b0
+ MX6QDL_PAD_RGMII_RD0__RGMII_RD0 0x1b0b0
+ MX6QDL_PAD_RGMII_RD1__RGMII_RD1 0x1b0b0
+ MX6QDL_PAD_RGMII_RD2__RGMII_RD2 0x1b0b0
+ MX6QDL_PAD_RGMII_RD3__RGMII_RD3 0x1b0b0
+ MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL 0x1b0b0
+ MX6QDL_PAD_ENET_TX_EN__ENET_TX_EN 0x1b0b0
+ MX6QDL_PAD_SD2_DAT1__GPIO1_IO14 0x1b0b0
+ >;
+ };
+
+ pinctrl_gpioleds_som: gpioledssomgrp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_4__GPIO1_IO04 0x1b0b0
+ >;
+ };
+
+ pinctrl_gpmi_nand: gpminandgrp {
+ fsl,pins = <
+ MX6QDL_PAD_NANDF_CLE__NAND_CLE 0xb0b1
+ MX6QDL_PAD_NANDF_ALE__NAND_ALE 0xb0b1
+ MX6QDL_PAD_NANDF_WP_B__NAND_WP_B 0xb0b1
+ MX6QDL_PAD_NANDF_RB0__NAND_READY_B 0xb000
+ MX6QDL_PAD_NANDF_CS0__NAND_CE0_B 0xb0b1
+ MX6QDL_PAD_NANDF_CS1__NAND_CE1_B 0xb0b1
+ MX6QDL_PAD_NANDF_CS2__NAND_CE2_B 0xb0b1
+ MX6QDL_PAD_NANDF_CS3__NAND_CE3_B 0xb0b1
+ MX6QDL_PAD_SD4_CMD__NAND_RE_B 0xb0b1
+ MX6QDL_PAD_SD4_CLK__NAND_WE_B 0xb0b1
+ MX6QDL_PAD_NANDF_D0__NAND_DATA00 0xb0b1
+ MX6QDL_PAD_NANDF_D1__NAND_DATA01 0xb0b1
+ MX6QDL_PAD_NANDF_D2__NAND_DATA02 0xb0b1
+ MX6QDL_PAD_NANDF_D3__NAND_DATA03 0xb0b1
+ MX6QDL_PAD_NANDF_D4__NAND_DATA04 0xb0b1
+ MX6QDL_PAD_NANDF_D5__NAND_DATA05 0xb0b1
+ MX6QDL_PAD_NANDF_D6__NAND_DATA06 0xb0b1
+ MX6QDL_PAD_NANDF_D7__NAND_DATA07 0xb0b1
+ MX6QDL_PAD_SD4_DAT0__NAND_DQS 0x00b1
+ >;
+ };
+
+ pinctrl_i2c3: i2c3grp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_6__I2C3_SDA 0x4001b8b1
+ MX6QDL_PAD_GPIO_5__I2C3_SCL 0x4001b8b1
+ >;
+ };
+
+ pinctrl_ecspi1: ecspi1grp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_D16__ECSPI1_SCLK 0x100b1
+ MX6QDL_PAD_EIM_D17__ECSPI1_MISO 0x100b1
+ MX6QDL_PAD_EIM_D18__ECSPI1_MOSI 0x100b1
+ MX6QDL_PAD_EIM_D19__GPIO3_IO19 0x1b0b0
+ >;
+ };
+
+ pinctrl_pmic: pmicgrp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_2__GPIO1_IO02 0x1b0b0
+ >;
+ };
+
+ pinctrl_usdhc4: usdhc4grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD4_CMD__SD4_CMD 0x17059
+ MX6QDL_PAD_SD4_CLK__SD4_CLK 0x10059
+ MX6QDL_PAD_SD4_DAT0__SD4_DATA0 0x17059
+ MX6QDL_PAD_SD4_DAT1__SD4_DATA1 0x17059
+ MX6QDL_PAD_SD4_DAT2__SD4_DATA2 0x17059
+ MX6QDL_PAD_SD4_DAT3__SD4_DATA3 0x17059
+ MX6QDL_PAD_SD4_DAT4__SD4_DATA4 0x17059
+ MX6QDL_PAD_SD4_DAT5__SD4_DATA5 0x17059
+ MX6QDL_PAD_SD4_DAT6__SD4_DATA6 0x17059
+ MX6QDL_PAD_SD4_DAT7__SD4_DATA7 0x17059
+ >;
+ };
+};
--
2.7.4
WARNING: multiple messages have this Message-ID (diff)
From: s.riedmueller@phytec.de (Stefan Riedmueller)
To: linux-arm-kernel@lists.infradead.org
Subject: [PATCH 1/6] ARM: dts: imx6: Add initial support for phyCORE-i.MX 6 SOM
Date: Tue, 19 Dec 2017 16:49:43 +0100 [thread overview]
Message-ID: <1513698588-13325-2-git-send-email-s.riedmueller@phytec.de> (raw)
In-Reply-To: <1513698588-13325-1-git-send-email-s.riedmueller@phytec.de>
This patch adds basic support for PHYTEC phyCORE-i.MX 6 SOM with i.MX
6Quad/Dual or i.MX 6DualLight/Solo.
Signed-off-by: Christian Hemp <c.hemp@phytec.de>
Signed-off-by: Stefan Christ <s.christ@phytec.de>
Signed-off-by: Christoph Fritz <chf.fritz@googlemail.com>
Signed-off-by: Stefan Riedmueller <s.riedmueller@phytec.de>
---
arch/arm/boot/dts/imx6qdl-phytec-phycore-som.dtsi | 282 ++++++++++++++++++++++
1 file changed, 282 insertions(+)
create mode 100644 arch/arm/boot/dts/imx6qdl-phytec-phycore-som.dtsi
diff --git a/arch/arm/boot/dts/imx6qdl-phytec-phycore-som.dtsi b/arch/arm/boot/dts/imx6qdl-phytec-phycore-som.dtsi
new file mode 100644
index 0000000..5283f0d
--- /dev/null
+++ b/arch/arm/boot/dts/imx6qdl-phytec-phycore-som.dtsi
@@ -0,0 +1,282 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (C) 2017 PHYTEC Messtechnik GmbH
+ * Author: Christian Hemp <c.hemp@phytec.de>
+ */
+
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+ model = "PHYTEC phyCORE-i.MX 6";
+ compatible = "phytec,imx6qdl-pcm058", "fsl,imx6qdl";
+
+ aliases {
+ ipu0 = &ipu1;
+ rtc1 = &da9062_rtc;
+ rtc2 = &snvs_rtc;
+ };
+
+ /*
+ * Set the minimum memory size here and
+ * let the bootloader set the real size.
+ */
+ memory {
+ reg = <0x10000000 0x8000000>;
+ };
+
+ gpio_leds_som: somleds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_gpioleds_som>;
+
+ som_green {
+ label = "phycore:green";
+ gpios = <&gpio1 4 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "heartbeat";
+ };
+ };
+};
+
+&ecspi1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ecspi1>;
+ cs-gpios = <&gpio3 19 GPIO_ACTIVE_LOW>;
+ status = "okay";
+
+ flash: flash at 0 {
+ compatible = "m25p80";
+ spi-max-frequency = <20000000>;
+ reg = <0>;
+ status = "disabled";
+ };
+};
+
+&fec {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_enet>;
+ phy-handle = <ðphy>;
+ phy-mode = "rgmii";
+ phy-supply = <&vdd_eth_io>;
+ phy-reset-gpios = <&gpio1 14 GPIO_ACTIVE_LOW>;
+ status = "disabled";
+
+ mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ethphy: ethernet-phy at 3 {
+ reg = <3>;
+ txc-skew-ps = <1680>;
+ rxc-skew-ps = <1860>;
+ };
+ };
+};
+
+&gpmi {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_gpmi_nand>;
+ nand-on-flash-bbt;
+ status = "disabled";
+};
+
+&i2c3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c3>;
+ clock-frequency = <400000>;
+ status = "okay";
+
+ eeprom: eeprom at 50 {
+ compatible = "cat,24c32";
+ reg = <0x50>;
+ };
+
+ pmic0: pmic at 58 {
+ compatible = "dlg,da9062";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pmic>;
+ reg = <0x58>;
+ interrupt-parent = <&gpio1>;
+ interrupts = <2 IRQ_TYPE_LEVEL_LOW>;
+ interrupt-controller;
+
+ da9062_rtc: rtc {
+ compatible = "dlg,da9062-rtc";
+ };
+
+ da9062_wdt: watchdog {
+ compatible = "dlg,da9062-watchdog";
+ };
+
+ da9062_reg: regulators {
+ vdd_arm: buck1 {
+ regulator-name = "vdd_arm";
+ regulator-min-microvolt = <730000>;
+ regulator-max-microvolt = <1380000>;
+ regulator-always-on;
+ };
+
+ vdd_soc: buck2 {
+ regulator-name = "vdd_soc";
+ regulator-min-microvolt = <730000>;
+ regulator-max-microvolt = <1380000>;
+ regulator-always-on;
+ };
+
+ vdd_ddr3_1p5: buck3 {
+ regulator-name = "vdd_ddr3";
+ regulator-min-microvolt = <1500000>;
+ regulator-max-microvolt = <1500000>;
+ regulator-always-on;
+ };
+
+ vdd_eth_1p2: buck4 {
+ regulator-name = "vdd_eth";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-always-on;
+ };
+
+ vdd_snvs: ldo1 {
+ regulator-name = "vdd_snvs";
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-always-on;
+ };
+
+ vdd_high: ldo2 {
+ regulator-name = "vdd_high";
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-always-on;
+ };
+
+ vdd_eth_io: ldo3 {
+ regulator-name = "vdd_eth_io";
+ regulator-min-microvolt = <2500000>;
+ regulator-max-microvolt = <2500000>;
+ };
+
+ vdd_emmc_1p8: ldo4 {
+ regulator-name = "vdd_emmc";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+ };
+ };
+};
+
+®_arm {
+ vin-supply = <&vdd_arm>;
+};
+
+®_pu {
+ vin-supply = <&vdd_soc>;
+};
+
+®_soc {
+ vin-supply = <&vdd_soc>;
+};
+
+&snvs_poweroff {
+ status = "okay";
+};
+
+&usdhc4 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usdhc4>;
+ bus-width = <8>;
+ non-removable;
+ vmmc-supply = <&vdd_emmc_1p8>;
+ status = "disabled";
+};
+
+&iomuxc {
+ pinctrl_enet: enetgrp {
+ fsl,pins = <
+ MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x1b0b0
+ MX6QDL_PAD_ENET_MDC__ENET_MDC 0x1b0b0
+ MX6QDL_PAD_RGMII_TXC__RGMII_TXC 0x1b0b0
+ MX6QDL_PAD_RGMII_TD0__RGMII_TD0 0x1b0b0
+ MX6QDL_PAD_RGMII_TD1__RGMII_TD1 0x1b0b0
+ MX6QDL_PAD_RGMII_TD2__RGMII_TD2 0x1b0b0
+ MX6QDL_PAD_RGMII_TD3__RGMII_TD3 0x1b0b0
+ MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL 0x1b0b0
+ MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK 0x1b0b0
+ MX6QDL_PAD_RGMII_RXC__RGMII_RXC 0x1b0b0
+ MX6QDL_PAD_RGMII_RD0__RGMII_RD0 0x1b0b0
+ MX6QDL_PAD_RGMII_RD1__RGMII_RD1 0x1b0b0
+ MX6QDL_PAD_RGMII_RD2__RGMII_RD2 0x1b0b0
+ MX6QDL_PAD_RGMII_RD3__RGMII_RD3 0x1b0b0
+ MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL 0x1b0b0
+ MX6QDL_PAD_ENET_TX_EN__ENET_TX_EN 0x1b0b0
+ MX6QDL_PAD_SD2_DAT1__GPIO1_IO14 0x1b0b0
+ >;
+ };
+
+ pinctrl_gpioleds_som: gpioledssomgrp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_4__GPIO1_IO04 0x1b0b0
+ >;
+ };
+
+ pinctrl_gpmi_nand: gpminandgrp {
+ fsl,pins = <
+ MX6QDL_PAD_NANDF_CLE__NAND_CLE 0xb0b1
+ MX6QDL_PAD_NANDF_ALE__NAND_ALE 0xb0b1
+ MX6QDL_PAD_NANDF_WP_B__NAND_WP_B 0xb0b1
+ MX6QDL_PAD_NANDF_RB0__NAND_READY_B 0xb000
+ MX6QDL_PAD_NANDF_CS0__NAND_CE0_B 0xb0b1
+ MX6QDL_PAD_NANDF_CS1__NAND_CE1_B 0xb0b1
+ MX6QDL_PAD_NANDF_CS2__NAND_CE2_B 0xb0b1
+ MX6QDL_PAD_NANDF_CS3__NAND_CE3_B 0xb0b1
+ MX6QDL_PAD_SD4_CMD__NAND_RE_B 0xb0b1
+ MX6QDL_PAD_SD4_CLK__NAND_WE_B 0xb0b1
+ MX6QDL_PAD_NANDF_D0__NAND_DATA00 0xb0b1
+ MX6QDL_PAD_NANDF_D1__NAND_DATA01 0xb0b1
+ MX6QDL_PAD_NANDF_D2__NAND_DATA02 0xb0b1
+ MX6QDL_PAD_NANDF_D3__NAND_DATA03 0xb0b1
+ MX6QDL_PAD_NANDF_D4__NAND_DATA04 0xb0b1
+ MX6QDL_PAD_NANDF_D5__NAND_DATA05 0xb0b1
+ MX6QDL_PAD_NANDF_D6__NAND_DATA06 0xb0b1
+ MX6QDL_PAD_NANDF_D7__NAND_DATA07 0xb0b1
+ MX6QDL_PAD_SD4_DAT0__NAND_DQS 0x00b1
+ >;
+ };
+
+ pinctrl_i2c3: i2c3grp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_6__I2C3_SDA 0x4001b8b1
+ MX6QDL_PAD_GPIO_5__I2C3_SCL 0x4001b8b1
+ >;
+ };
+
+ pinctrl_ecspi1: ecspi1grp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_D16__ECSPI1_SCLK 0x100b1
+ MX6QDL_PAD_EIM_D17__ECSPI1_MISO 0x100b1
+ MX6QDL_PAD_EIM_D18__ECSPI1_MOSI 0x100b1
+ MX6QDL_PAD_EIM_D19__GPIO3_IO19 0x1b0b0
+ >;
+ };
+
+ pinctrl_pmic: pmicgrp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_2__GPIO1_IO02 0x1b0b0
+ >;
+ };
+
+ pinctrl_usdhc4: usdhc4grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD4_CMD__SD4_CMD 0x17059
+ MX6QDL_PAD_SD4_CLK__SD4_CLK 0x10059
+ MX6QDL_PAD_SD4_DAT0__SD4_DATA0 0x17059
+ MX6QDL_PAD_SD4_DAT1__SD4_DATA1 0x17059
+ MX6QDL_PAD_SD4_DAT2__SD4_DATA2 0x17059
+ MX6QDL_PAD_SD4_DAT3__SD4_DATA3 0x17059
+ MX6QDL_PAD_SD4_DAT4__SD4_DATA4 0x17059
+ MX6QDL_PAD_SD4_DAT5__SD4_DATA5 0x17059
+ MX6QDL_PAD_SD4_DAT6__SD4_DATA6 0x17059
+ MX6QDL_PAD_SD4_DAT7__SD4_DATA7 0x17059
+ >;
+ };
+};
--
2.7.4
next prev parent reply other threads:[~2017-12-19 15:49 UTC|newest]
Thread overview: 30+ messages / expand[flat|nested] mbox.gz Atom feed top
2017-12-19 15:49 [PATCH 0/6] ARM: dts: Add PHYTEC phyCORE-i.MX 6 and phyBOARD-Mira carrier board support Stefan Riedmueller
2017-12-19 15:49 ` Stefan Riedmueller
2017-12-19 15:49 ` Stefan Riedmueller [this message]
2017-12-19 15:49 ` [PATCH 1/6] ARM: dts: imx6: Add initial support for phyCORE-i.MX 6 SOM Stefan Riedmueller
[not found] ` <1513698588-13325-2-git-send-email-s.riedmueller-guT5V/WYfQezQB+pC5nmwQ@public.gmane.org>
2017-12-19 17:03 ` Fabio Estevam
2017-12-19 17:03 ` Fabio Estevam
2017-12-19 15:49 ` [PATCH 2/6] ARM: dts: imx6: Add initial support for phyBOARD-Mira Stefan Riedmueller
2017-12-19 15:49 ` Stefan Riedmueller
[not found] ` <1513698588-13325-3-git-send-email-s.riedmueller-guT5V/WYfQezQB+pC5nmwQ@public.gmane.org>
2017-12-19 17:10 ` Fabio Estevam
2017-12-19 17:10 ` Fabio Estevam
[not found] ` <CAOMZO5CSQSpPXTnR69HqHfKZiUpi+eqonqjuEu9mgBECsWG_5g-JsoAwUIsXosN+BqQ9rBEUg@public.gmane.org>
2017-12-19 17:22 ` Christoph Fritz
2017-12-19 17:22 ` Christoph Fritz
2017-12-19 15:49 ` [PATCH 3/6] ARM: dts: imx6: Add support for phyBOARD-Mira i.MX 6Quad/Dual RDK Stefan Riedmueller
2017-12-19 15:49 ` Stefan Riedmueller
[not found] ` <1513698588-13325-4-git-send-email-s.riedmueller-guT5V/WYfQezQB+pC5nmwQ@public.gmane.org>
2017-12-19 17:12 ` Fabio Estevam
2017-12-19 17:12 ` Fabio Estevam
2017-12-19 15:49 ` [PATCH 4/6] ARM: dts: imx6: Add support for phxBOARD-Mira i.MX 6 DualLight/Solo RDK Stefan Riedmueller
2017-12-19 15:49 ` Stefan Riedmueller
[not found] ` <1513698588-13325-5-git-send-email-s.riedmueller-guT5V/WYfQezQB+pC5nmwQ@public.gmane.org>
2017-12-19 17:14 ` Fabio Estevam
2017-12-19 17:14 ` Fabio Estevam
2017-12-19 15:49 ` [PATCH 5/6] ARM: dts: imx6: Add support for phyBOARD-Mira with i.MX 6QuadPlus Stefan Riedmueller
2017-12-19 15:49 ` Stefan Riedmueller
[not found] ` <1513698588-13325-6-git-send-email-s.riedmueller-guT5V/WYfQezQB+pC5nmwQ@public.gmane.org>
2017-12-19 17:15 ` Fabio Estevam
2017-12-19 17:15 ` Fabio Estevam
2017-12-19 15:49 ` [PATCH 6/6] ARM: imx_v6_v7_defconfig: Enable Dialog Semicondocter DA9062 driver Stefan Riedmueller
2017-12-19 15:49 ` Stefan Riedmueller
[not found] ` <1513698588-13325-7-git-send-email-s.riedmueller-guT5V/WYfQezQB+pC5nmwQ@public.gmane.org>
2017-12-19 17:16 ` Fabio Estevam
2017-12-19 17:16 ` Fabio Estevam
[not found] ` <CAOMZO5CyMoY+24ub09Lp4VHFn=O6FqFELfQzH-WDv1H9OweoHw-JsoAwUIsXosN+BqQ9rBEUg@public.gmane.org>
2017-12-19 17:32 ` Fabio Estevam
2017-12-19 17:32 ` Fabio Estevam
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1513698588-13325-2-git-send-email-s.riedmueller@phytec.de \
--to=s.riedmueller@phytec.de \
--cc=c.hemp@phytec.de \
--cc=chf.fritz@googlemail.com \
--cc=devicetree@vger.kernel.org \
--cc=fabio.estevam@nxp.com \
--cc=kernel@pengutronix.de \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=mark.rutland@arm.com \
--cc=robh+dt@kernel.org \
--cc=s.christ@phytec.de \
--cc=shawnguo@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.