From: <qii.wang-NuS5LvNUpcJWk0Htik3J/w@public.gmane.org>
To: linux-mediatek-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r@public.gmane.org
Cc: qii wang <qii.wang-NuS5LvNUpcJWk0Htik3J/w@public.gmane.org>,
srv_heupstream-NuS5LvNUpcJWk0Htik3J/w@public.gmane.org
Subject: [PATCH] i2c: mediatek: Add driver for MediaTek MT8183 I2C controller
Date: Fri, 23 Nov 2018 16:05:30 +0800 [thread overview]
Message-ID: <1542960330-28839-1-git-send-email-qii.wang@mediatek.com> (raw)
From: qii wang <qii.wang-NuS5LvNUpcJWk0Htik3J/w@public.gmane.org>
Add mediatek MT8183 I2C controller driver. Compare to I2C controller
of earlier mediatek SoC, MT8183 has different registers, offsets, clock,
and add multi-user function.
Change-Id: I6027787c978f1f2e4a923095bfc46e971879d1a6
Signed-off-by: qii wang <qii.wang-NuS5LvNUpcJWk0Htik3J/w@public.gmane.org>
---
drivers/i2c/busses/i2c-mt65xx.c | 279 ++++++++++++++++++++++++++++++---------
1 file changed, 214 insertions(+), 65 deletions(-)
diff --git a/drivers/i2c/busses/i2c-mt65xx.c b/drivers/i2c/busses/i2c-mt65xx.c
index a74ef76..5b515c8 100644
--- a/drivers/i2c/busses/i2c-mt65xx.c
+++ b/drivers/i2c/busses/i2c-mt65xx.c
@@ -35,22 +35,26 @@
#include <linux/slab.h>
#define I2C_RS_TRANSFER (1 << 4)
+#define I2C_ARB_LOST (1 << 3)
#define I2C_HS_NACKERR (1 << 2)
#define I2C_ACKERR (1 << 1)
#define I2C_TRANSAC_COMP (1 << 0)
#define I2C_TRANSAC_START (1 << 0)
+#define I2C_RESUME_ARBIT (1 << 1)
#define I2C_RS_MUL_CNFG (1 << 15)
#define I2C_RS_MUL_TRIG (1 << 14)
#define I2C_DCM_DISABLE 0x0000
#define I2C_IO_CONFIG_OPEN_DRAIN 0x0003
#define I2C_IO_CONFIG_PUSH_PULL 0x0000
#define I2C_SOFT_RST 0x0001
-#define I2C_FIFO_ADDR_CLR 0x0001
+#define I2C_FIFO_ADDR_CLR 0x0003
+#define I2C_HFIFO_DATA 0x8208
+#define I2C_FIFO_ADDR_CLR_MCH 0x0004
#define I2C_DELAY_LEN 0x0002
#define I2C_ST_START_CON 0x8001
#define I2C_FS_START_CON 0x1800
#define I2C_TIME_CLR_VALUE 0x0000
-#define I2C_TIME_DEFAULT_VALUE 0x0003
+#define I2C_TIME_DEFAULT_VALUE 0x0083
#define I2C_WRRD_TRANAC_VALUE 0x0002
#define I2C_RD_TRANAC_VALUE 0x0001
@@ -76,6 +80,8 @@
#define I2C_CONTROL_DIR_CHANGE (0x1 << 4)
#define I2C_CONTROL_ACKERR_DET_EN (0x1 << 5)
#define I2C_CONTROL_TRANSFER_LEN_CHANGE (0x1 << 6)
+#define I2C_CONTROL_DMAACK_EN (0x1 << 8)
+#define I2C_CONTROL_ASYNC_MODE (0x1 << 9)
#define I2C_CONTROL_WRAPPER (0x1 << 0)
#define I2C_DRV_NAME "i2c-mt65xx"
@@ -106,34 +112,104 @@ enum mtk_trans_op {
};
enum I2C_REGS_OFFSET {
- OFFSET_DATA_PORT = 0x0,
- OFFSET_SLAVE_ADDR = 0x04,
- OFFSET_INTR_MASK = 0x08,
- OFFSET_INTR_STAT = 0x0c,
- OFFSET_CONTROL = 0x10,
- OFFSET_TRANSFER_LEN = 0x14,
- OFFSET_TRANSAC_LEN = 0x18,
- OFFSET_DELAY_LEN = 0x1c,
- OFFSET_TIMING = 0x20,
- OFFSET_START = 0x24,
- OFFSET_EXT_CONF = 0x28,
- OFFSET_FIFO_STAT = 0x30,
- OFFSET_FIFO_THRESH = 0x34,
- OFFSET_FIFO_ADDR_CLR = 0x38,
- OFFSET_IO_CONFIG = 0x40,
- OFFSET_RSV_DEBUG = 0x44,
- OFFSET_HS = 0x48,
- OFFSET_SOFTRESET = 0x50,
- OFFSET_DCM_EN = 0x54,
- OFFSET_PATH_DIR = 0x60,
- OFFSET_DEBUGSTAT = 0x64,
- OFFSET_DEBUGCTRL = 0x68,
- OFFSET_TRANSFER_LEN_AUX = 0x6c,
- OFFSET_CLOCK_DIV = 0x70,
+ OFFSET_DATA_PORT,
+ OFFSET_SLAVE_ADDR,
+ OFFSET_INTR_MASK,
+ OFFSET_INTR_STAT,
+ OFFSET_CONTROL,
+ OFFSET_TRANSFER_LEN,
+ OFFSET_TRANSAC_LEN,
+ OFFSET_DELAY_LEN,
+ OFFSET_TIMING,
+ OFFSET_START,
+ OFFSET_EXT_CONF,
+ OFFSET_FIFO_STAT,
+ OFFSET_FIFO_THRESH,
+ OFFSET_FIFO_ADDR_CLR,
+ OFFSET_IO_CONFIG,
+ OFFSET_RSV_DEBUG,
+ OFFSET_HS,
+ OFFSET_SOFTRESET,
+ OFFSET_DCM_EN,
+ OFFSET_PATH_DIR,
+ OFFSET_DEBUGSTAT,
+ OFFSET_DEBUGCTRL,
+ OFFSET_TRANSFER_LEN_AUX,
+ OFFSET_CLOCK_DIV,
+ /* MT8183 only regs */
+ OFFSET_LTIMING,
+ OFFSET_DATA_TIMING,
+ OFFSET_MCU_INTR,
+ OFFSET_HW_TIMEOUT,
+ OFFSET_HFIFO_DATA,
+ OFFSET_HFIFO_STAT,
+ OFFSET_MULTI_DMA,
+ OFFSET_ROLLBACK,
+};
+
+static const u16 mt_i2c_regs_v1[] = {
+ [OFFSET_DATA_PORT] = 0x0,
+ [OFFSET_SLAVE_ADDR] = 0x4,
+ [OFFSET_INTR_MASK] = 0x8,
+ [OFFSET_INTR_STAT] = 0xc,
+ [OFFSET_CONTROL] = 0x10,
+ [OFFSET_TRANSFER_LEN] = 0x14,
+ [OFFSET_TRANSAC_LEN] = 0x18,
+ [OFFSET_DELAY_LEN] = 0x1c,
+ [OFFSET_TIMING] = 0x20,
+ [OFFSET_START] = 0x24,
+ [OFFSET_EXT_CONF] = 0x28,
+ [OFFSET_FIFO_STAT] = 0x30,
+ [OFFSET_FIFO_THRESH] = 0x34,
+ [OFFSET_FIFO_ADDR_CLR] = 0x38,
+ [OFFSET_IO_CONFIG] = 0x40,
+ [OFFSET_RSV_DEBUG] = 0x44,
+ [OFFSET_HS] = 0x48,
+ [OFFSET_SOFTRESET] = 0x50,
+ [OFFSET_DCM_EN] = 0x54,
+ [OFFSET_PATH_DIR] = 0x60,
+ [OFFSET_DEBUGSTAT] = 0x64,
+ [OFFSET_DEBUGCTRL] = 0x68,
+ [OFFSET_TRANSFER_LEN_AUX] = 0x6c,
+ [OFFSET_CLOCK_DIV] = 0x70,
+};
+
+static const u16 mt_i2c_regs_v2[] = {
+ [OFFSET_DATA_PORT] = 0x0,
+ [OFFSET_SLAVE_ADDR] = 0x4,
+ [OFFSET_INTR_MASK] = 0x8,
+ [OFFSET_INTR_STAT] = 0xc,
+ [OFFSET_CONTROL] = 0x10,
+ [OFFSET_TRANSFER_LEN] = 0x14,
+ [OFFSET_TRANSAC_LEN] = 0x18,
+ [OFFSET_DELAY_LEN] = 0x1c,
+ [OFFSET_TIMING] = 0x20,
+ [OFFSET_START] = 0x24,
+ [OFFSET_EXT_CONF] = 0x28,
+ [OFFSET_LTIMING] = 0x2c,
+ [OFFSET_HS] = 0x30,
+ [OFFSET_IO_CONFIG] = 0x34,
+ [OFFSET_FIFO_ADDR_CLR] = 0x38,
+ [OFFSET_DATA_TIMING] = 0x3c,
+ [OFFSET_MCU_INTR] = 0x40,
+ [OFFSET_TRANSFER_LEN_AUX] = 0x44,
+ [OFFSET_CLOCK_DIV] = 0x48,
+ [OFFSET_HW_TIMEOUT] = 0x4c,
+ [OFFSET_SOFTRESET] = 0x50,
+ [OFFSET_HFIFO_DATA] = 0x70,
+ [OFFSET_DEBUGSTAT] = 0xe0,
+ [OFFSET_DEBUGCTRL] = 0xe8,
+ [OFFSET_FIFO_STAT] = 0xf4,
+ [OFFSET_FIFO_THRESH] = 0xf8,
+ [OFFSET_HFIFO_STAT] = 0xfc,
+ [OFFSET_DCM_EN] = 0xf88,
+ [OFFSET_MULTI_DMA] = 0xf8c,
+ [OFFSET_ROLLBACK] = 0xf98,
};
struct mtk_i2c_compatible {
const struct i2c_adapter_quirks *quirks;
+ const u16 *regs;
unsigned char pmic_i2c: 1;
unsigned char dcm: 1;
unsigned char auto_restart: 1;
@@ -153,8 +229,10 @@ struct mtk_i2c {
struct clk *clk_main; /* main clock for i2c bus */
struct clk *clk_dma; /* DMA clock for i2c via DMA */
struct clk *clk_pmic; /* PMIC clock for i2c from PMIC */
+ struct clk *clk_arb; /* Arbitrator clock for i2c */
bool have_pmic; /* can use i2c pins from PMIC */
bool use_push_pull; /* IO config push-pull mode */
+ u32 ch_offset; /* i2c multi-user channel offset */
u16 irq_stat; /* interrupt status */
unsigned int clk_src_div;
@@ -162,6 +240,7 @@ struct mtk_i2c {
enum mtk_trans_op op;
u16 timing_reg;
u16 high_speed_reg;
+ u16 ltiming_reg;
unsigned char auto_restart;
bool ignore_restart_irq;
const struct mtk_i2c_compatible *dev_comp;
@@ -181,6 +260,7 @@ struct mtk_i2c {
};
static const struct mtk_i2c_compatible mt2712_compat = {
+ .regs = mt_i2c_regs_v1,
.pmic_i2c = 0,
.dcm = 1,
.auto_restart = 1,
@@ -191,6 +271,7 @@ struct mtk_i2c {
static const struct mtk_i2c_compatible mt6577_compat = {
.quirks = &mt6577_i2c_quirks,
+ .regs = mt_i2c_regs_v1,
.pmic_i2c = 0,
.dcm = 1,
.auto_restart = 0,
@@ -201,6 +282,7 @@ struct mtk_i2c {
static const struct mtk_i2c_compatible mt6589_compat = {
.quirks = &mt6577_i2c_quirks,
+ .regs = mt_i2c_regs_v1,
.pmic_i2c = 1,
.dcm = 0,
.auto_restart = 0,
@@ -211,6 +293,7 @@ struct mtk_i2c {
static const struct mtk_i2c_compatible mt7622_compat = {
.quirks = &mt7622_i2c_quirks,
+ .regs = mt_i2c_regs_v1,
.pmic_i2c = 0,
.dcm = 1,
.auto_restart = 1,
@@ -220,6 +303,7 @@ struct mtk_i2c {
};
static const struct mtk_i2c_compatible mt8173_compat = {
+ .regs = mt_i2c_regs_v1,
.pmic_i2c = 0,
.dcm = 1,
.auto_restart = 1,
@@ -228,16 +312,38 @@ struct mtk_i2c {
.timing_adjust = 0,
};
+static const struct mtk_i2c_compatible mt8183_compat = {
+ .regs = mt_i2c_regs_v2,
+ .pmic_i2c = 0,
+ .dcm = 0,
+ .auto_restart = 1,
+ .aux_len_reg = 1,
+ .support_33bits = 1,
+ .timing_adjust = 1,
+};
+
static const struct of_device_id mtk_i2c_of_match[] = {
{ .compatible = "mediatek,mt2712-i2c", .data = &mt2712_compat },
{ .compatible = "mediatek,mt6577-i2c", .data = &mt6577_compat },
{ .compatible = "mediatek,mt6589-i2c", .data = &mt6589_compat },
{ .compatible = "mediatek,mt7622-i2c", .data = &mt7622_compat },
{ .compatible = "mediatek,mt8173-i2c", .data = &mt8173_compat },
+ { .compatible = "mediatek,mt8183-i2c", .data = &mt8183_compat },
{}
};
MODULE_DEVICE_TABLE(of, mtk_i2c_of_match);
+static u16 mtk_i2c_readw(struct mtk_i2c *i2c, enum I2C_REGS_OFFSET reg)
+{
+ return readw(i2c->base + i2c->ch_offset + i2c->dev_comp->regs[reg]);
+}
+
+static void mtk_i2c_writew(struct mtk_i2c *i2c, u16 val,
+ enum I2C_REGS_OFFSET reg)
+{
+ writew(val, i2c->base + i2c->ch_offset + i2c->dev_comp->regs[reg]);
+}
+
static int mtk_i2c_clock_enable(struct mtk_i2c *i2c)
{
int ret;
@@ -255,8 +361,18 @@ static int mtk_i2c_clock_enable(struct mtk_i2c *i2c)
if (ret)
goto err_pmic;
}
+
+ if (i2c->clk_arb != NULL) {
+ ret = clk_prepare_enable(i2c->clk_arb);
+ if (ret)
+ goto err_arb;
+ }
+
return 0;
+err_arb:
+ if (i2c->have_pmic)
+ clk_disable_unprepare(i2c->clk_pmic);
err_pmic:
clk_disable_unprepare(i2c->clk_main);
err_main:
@@ -267,6 +383,9 @@ static int mtk_i2c_clock_enable(struct mtk_i2c *i2c)
static void mtk_i2c_clock_disable(struct mtk_i2c *i2c)
{
+ if (i2c->clk_arb != NULL)
+ clk_disable_unprepare(i2c->clk_arb);
+
if (i2c->have_pmic)
clk_disable_unprepare(i2c->clk_pmic);
@@ -278,31 +397,40 @@ static void mtk_i2c_init_hw(struct mtk_i2c *i2c)
{
u16 control_reg;
- writew(I2C_SOFT_RST, i2c->base + OFFSET_SOFTRESET);
+ mtk_i2c_writew(i2c, I2C_SOFT_RST, OFFSET_SOFTRESET);
/* Set ioconfig */
if (i2c->use_push_pull)
- writew(I2C_IO_CONFIG_PUSH_PULL, i2c->base + OFFSET_IO_CONFIG);
+ mtk_i2c_writew(i2c, I2C_IO_CONFIG_PUSH_PULL, OFFSET_IO_CONFIG);
else
- writew(I2C_IO_CONFIG_OPEN_DRAIN, i2c->base + OFFSET_IO_CONFIG);
+ mtk_i2c_writew(i2c, I2C_IO_CONFIG_OPEN_DRAIN, OFFSET_IO_CONFIG);
if (i2c->dev_comp->dcm)
- writew(I2C_DCM_DISABLE, i2c->base + OFFSET_DCM_EN);
+ mtk_i2c_writew(i2c, I2C_DCM_DISABLE, OFFSET_DCM_EN);
+
+ if (i2c->ch_offset)
+ writew(I2C_RESUME_ARBIT, i2c->base +
+ i2c->dev_comp->regs[OFFSET_START]);
if (i2c->dev_comp->timing_adjust)
- writew(I2C_DEFAULT_CLK_DIV - 1, i2c->base + OFFSET_CLOCK_DIV);
+ mtk_i2c_writew(i2c, (I2C_DEFAULT_CLK_DIV - 1) |
+ (I2C_DEFAULT_CLK_DIV - 1) << 8,
+ OFFSET_CLOCK_DIV);
- writew(i2c->timing_reg, i2c->base + OFFSET_TIMING);
- writew(i2c->high_speed_reg, i2c->base + OFFSET_HS);
+ mtk_i2c_writew(i2c, i2c->timing_reg, OFFSET_TIMING);
+ mtk_i2c_writew(i2c, i2c->high_speed_reg, OFFSET_HS);
+ if (i2c->dev_comp->regs == mt_i2c_regs_v2)
+ mtk_i2c_writew(i2c, i2c->ltiming_reg, OFFSET_LTIMING);
/* If use i2c pin from PMIC mt6397 side, need set PATH_DIR first */
if (i2c->have_pmic)
- writew(I2C_CONTROL_WRAPPER, i2c->base + OFFSET_PATH_DIR);
+ mtk_i2c_writew(i2c, I2C_CONTROL_WRAPPER, OFFSET_PATH_DIR);
- control_reg = I2C_CONTROL_ACKERR_DET_EN |
- I2C_CONTROL_CLK_EXT_EN | I2C_CONTROL_DMA_EN;
- writew(control_reg, i2c->base + OFFSET_CONTROL);
- writew(I2C_DELAY_LEN, i2c->base + OFFSET_DELAY_LEN);
+ control_reg = I2C_CONTROL_ACKERR_DET_EN | I2C_CONTROL_DMAACK_EN |
+ I2C_CONTROL_CLK_EXT_EN | I2C_CONTROL_DMA_EN |
+ I2C_CONTROL_ASYNC_MODE;
+ mtk_i2c_writew(i2c, control_reg, OFFSET_CONTROL);
+ mtk_i2c_writew(i2c, I2C_DELAY_LEN, OFFSET_DELAY_LEN);
writel(I2C_DMA_HARD_RST, i2c->pdmabase + OFFSET_RST);
udelay(50);
@@ -390,6 +518,8 @@ static int mtk_i2c_set_speed(struct mtk_i2c *i2c, unsigned int parent_clk)
unsigned int clk_src;
unsigned int step_cnt;
unsigned int sample_cnt;
+ unsigned int l_step_cnt;
+ unsigned int l_sample_cnt;
unsigned int target_speed;
int ret;
@@ -399,11 +529,11 @@ static int mtk_i2c_set_speed(struct mtk_i2c *i2c, unsigned int parent_clk)
if (target_speed > MAX_FS_MODE_SPEED) {
/* Set master code speed register */
ret = mtk_i2c_calculate_speed(i2c, clk_src, MAX_FS_MODE_SPEED,
- &step_cnt, &sample_cnt);
+ &l_step_cnt, &l_sample_cnt);
if (ret < 0)
return ret;
- i2c->timing_reg = (sample_cnt << 8) | step_cnt;
+ i2c->timing_reg = (l_sample_cnt << 8) | l_step_cnt;
/* Set the high speed mode register */
ret = mtk_i2c_calculate_speed(i2c, clk_src, target_speed,
@@ -413,6 +543,8 @@ static int mtk_i2c_set_speed(struct mtk_i2c *i2c, unsigned int parent_clk)
i2c->high_speed_reg = I2C_TIME_DEFAULT_VALUE |
(sample_cnt << 12) | (step_cnt << 8);
+ i2c->ltiming_reg = (l_sample_cnt << 6) | l_step_cnt |
+ (sample_cnt << 12) | (step_cnt << 9);
} else {
ret = mtk_i2c_calculate_speed(i2c, clk_src, target_speed,
&step_cnt, &sample_cnt);
@@ -423,6 +555,8 @@ static int mtk_i2c_set_speed(struct mtk_i2c *i2c, unsigned int parent_clk)
/* Disable the high speed transaction */
i2c->high_speed_reg = I2C_TIME_CLR_VALUE;
+
+ i2c->ltiming_reg = (sample_cnt << 6) | step_cnt;
}
return 0;
@@ -454,7 +588,7 @@ static int mtk_i2c_do_transfer(struct mtk_i2c *i2c, struct i2c_msg *msgs,
reinit_completion(&i2c->msg_complete);
- control_reg = readw(i2c->base + OFFSET_CONTROL) &
+ control_reg = mtk_i2c_readw(i2c, OFFSET_CONTROL) &
~(I2C_CONTROL_DIR_CHANGE | I2C_CONTROL_RS);
if ((i2c->speed_hz > 400000) || (left_num >= 1))
control_reg |= I2C_CONTROL_RS;
@@ -462,40 +596,47 @@ static int mtk_i2c_do_transfer(struct mtk_i2c *i2c, struct i2c_msg *msgs,
if (i2c->op == I2C_MASTER_WRRD)
control_reg |= I2C_CONTROL_DIR_CHANGE | I2C_CONTROL_RS;
- writew(control_reg, i2c->base + OFFSET_CONTROL);
+ mtk_i2c_writew(i2c, control_reg, OFFSET_CONTROL);
/* set start condition */
if (i2c->speed_hz <= 100000)
- writew(I2C_ST_START_CON, i2c->base + OFFSET_EXT_CONF);
+ mtk_i2c_writew(i2c, I2C_ST_START_CON, OFFSET_EXT_CONF);
else
- writew(I2C_FS_START_CON, i2c->base + OFFSET_EXT_CONF);
+ mtk_i2c_writew(i2c, I2C_FS_START_CON, OFFSET_EXT_CONF);
addr_reg = i2c_8bit_addr_from_msg(msgs);
- writew(addr_reg, i2c->base + OFFSET_SLAVE_ADDR);
+ mtk_i2c_writew(i2c, addr_reg, OFFSET_SLAVE_ADDR);
/* Clear interrupt status */
- writew(restart_flag | I2C_HS_NACKERR | I2C_ACKERR |
- I2C_TRANSAC_COMP, i2c->base + OFFSET_INTR_STAT);
- writew(I2C_FIFO_ADDR_CLR, i2c->base + OFFSET_FIFO_ADDR_CLR);
+ mtk_i2c_writew(i2c, restart_flag | I2C_HS_NACKERR | I2C_ACKERR |
+ I2C_ARB_LOST | I2C_TRANSAC_COMP,
+ OFFSET_INTR_STAT);
+
+ mtk_i2c_writew(i2c, I2C_FIFO_ADDR_CLR_MCH | I2C_FIFO_ADDR_CLR,
+ OFFSET_FIFO_ADDR_CLR);
+
+ if ((i2c->speed_hz > 400000) && (i2c->dev_comp->regs == mt_i2c_regs_v2))
+ mtk_i2c_writew(i2c, I2C_HFIFO_DATA, OFFSET_HFIFO_DATA);
/* Enable interrupt */
- writew(restart_flag | I2C_HS_NACKERR | I2C_ACKERR |
- I2C_TRANSAC_COMP, i2c->base + OFFSET_INTR_MASK);
+ mtk_i2c_writew(i2c, restart_flag | I2C_HS_NACKERR | I2C_ACKERR |
+ I2C_ARB_LOST | I2C_TRANSAC_COMP,
+ OFFSET_INTR_MASK);
/* Set transfer and transaction len */
if (i2c->op == I2C_MASTER_WRRD) {
if (i2c->dev_comp->aux_len_reg) {
- writew(msgs->len, i2c->base + OFFSET_TRANSFER_LEN);
- writew((msgs + 1)->len, i2c->base +
- OFFSET_TRANSFER_LEN_AUX);
+ mtk_i2c_writew(i2c, msgs->len, OFFSET_TRANSFER_LEN);
+ mtk_i2c_writew(i2c, (msgs + 1)->len,
+ OFFSET_TRANSFER_LEN_AUX);
} else {
- writew(msgs->len | ((msgs + 1)->len) << 8,
- i2c->base + OFFSET_TRANSFER_LEN);
+ mtk_i2c_writew(i2c, msgs->len | ((msgs + 1)->len) << 8,
+ OFFSET_TRANSFER_LEN);
}
- writew(I2C_WRRD_TRANAC_VALUE, i2c->base + OFFSET_TRANSAC_LEN);
+ mtk_i2c_writew(i2c, I2C_WRRD_TRANAC_VALUE, OFFSET_TRANSAC_LEN);
} else {
- writew(msgs->len, i2c->base + OFFSET_TRANSFER_LEN);
- writew(num, i2c->base + OFFSET_TRANSAC_LEN);
+ mtk_i2c_writew(i2c, msgs->len, OFFSET_TRANSFER_LEN);
+ mtk_i2c_writew(i2c, num, OFFSET_TRANSAC_LEN);
}
/* Prepare buffer data to start transfer */
@@ -607,14 +748,14 @@ static int mtk_i2c_do_transfer(struct mtk_i2c *i2c, struct i2c_msg *msgs,
if (left_num >= 1)
start_reg |= I2C_RS_MUL_CNFG;
}
- writew(start_reg, i2c->base + OFFSET_START);
+ mtk_i2c_writew(i2c, start_reg, OFFSET_START);
ret = wait_for_completion_timeout(&i2c->msg_complete,
i2c->adap.timeout);
/* Clear interrupt mask */
- writew(~(restart_flag | I2C_HS_NACKERR | I2C_ACKERR |
- I2C_TRANSAC_COMP), i2c->base + OFFSET_INTR_MASK);
+ mtk_i2c_writew(i2c, ~(restart_flag | I2C_HS_NACKERR | I2C_ACKERR |
+ I2C_ARB_LOST | I2C_TRANSAC_COMP), OFFSET_INTR_MASK);
if (i2c->op == I2C_MASTER_WR) {
dma_unmap_single(i2c->dev, wpaddr,
@@ -726,8 +867,8 @@ static irqreturn_t mtk_i2c_irq(int irqno, void *dev_id)
if (i2c->auto_restart)
restart_flag = I2C_RS_TRANSFER;
- intr_stat = readw(i2c->base + OFFSET_INTR_STAT);
- writew(intr_stat, i2c->base + OFFSET_INTR_STAT);
+ intr_stat = mtk_i2c_readw(i2c, OFFSET_INTR_STAT);
+ mtk_i2c_writew(i2c, intr_stat, OFFSET_INTR_STAT);
/*
* when occurs ack error, i2c controller generate two interrupts
@@ -739,8 +880,8 @@ static irqreturn_t mtk_i2c_irq(int irqno, void *dev_id)
if (i2c->ignore_restart_irq && (i2c->irq_stat & restart_flag)) {
i2c->ignore_restart_irq = false;
i2c->irq_stat = 0;
- writew(I2C_RS_MUL_CNFG | I2C_RS_MUL_TRIG | I2C_TRANSAC_START,
- i2c->base + OFFSET_START);
+ mtk_i2c_writew(i2c, I2C_RS_MUL_CNFG | I2C_RS_MUL_TRIG |
+ I2C_TRANSAC_START, OFFSET_START);
} else {
if (i2c->irq_stat & (I2C_TRANSAC_COMP | restart_flag))
complete(&i2c->msg_complete);
@@ -774,6 +915,10 @@ static int mtk_i2c_parse_dt(struct device_node *np, struct mtk_i2c *i2c)
if (i2c->clk_src_div == 0)
return -EINVAL;
+ ret = of_property_read_u32(np, "ch_offset", &i2c->ch_offset);
+ if (ret < 0)
+ i2c->ch_offset = 0;
+
i2c->have_pmic = of_property_read_bool(np, "mediatek,have-pmic");
i2c->use_push_pull =
of_property_read_bool(np, "mediatek,use-push-pull");
@@ -841,6 +986,10 @@ static int mtk_i2c_probe(struct platform_device *pdev)
return PTR_ERR(i2c->clk_dma);
}
+ i2c->clk_arb = devm_clk_get(&pdev->dev, "arb");
+ if (IS_ERR(i2c->clk_arb))
+ i2c->clk_arb = NULL;
+
clk = i2c->clk_main;
if (i2c->have_pmic) {
i2c->clk_pmic = devm_clk_get(&pdev->dev, "pmic");
--
1.7.9.5
next reply other threads:[~2018-11-23 8:05 UTC|newest]
Thread overview: 2+ messages / expand[flat|nested] mbox.gz Atom feed top
2018-11-23 8:05 qii.wang-NuS5LvNUpcJWk0Htik3J/w [this message]
[not found] ` <1542960330-28839-1-git-send-email-qii.wang-NuS5LvNUpcJWk0Htik3J/w@public.gmane.org>
2018-11-24 5:08 ` [PATCH] i2c: mediatek: Add driver for MediaTek MT8183 I2C controller Sean Wang
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1542960330-28839-1-git-send-email-qii.wang@mediatek.com \
--to=qii.wang-nus5lvnupcjwk0htik3j/w@public.gmane.org \
--cc=linux-mediatek-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r@public.gmane.org \
--cc=srv_heupstream-NuS5LvNUpcJWk0Htik3J/w@public.gmane.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.