From: Ludovic Barre <ludovic.Barre@st.com>
To: Rob Herring <robh+dt@kernel.org>, Mark Rutland <mark.rutland@arm.com>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>,
Alexandre Torgue <alexandre.torgue@st.com>,
<devicetree@vger.kernel.org>,
<linux-arm-kernel@lists.infradead.org>,
<linux-kernel@vger.kernel.org>,
<linux-stm32@st-md-mailman.stormreply.com>,
Ludovic Barre <ludovic.barre@st.com>
Subject: [PATCH 6/7] ARM: dts: stm32: add sdmmc1 support on stm32mp157c ed1 board
Date: Fri, 1 Mar 2019 09:47:47 +0100 [thread overview]
Message-ID: <1551430068-9456-7-git-send-email-ludovic.Barre@st.com> (raw)
In-Reply-To: <1551430068-9456-1-git-send-email-ludovic.Barre@st.com>
From: Ludovic Barre <ludovic.barre@st.com>
This patch adds sdmmc1 support on stm32mp157c ed1 board.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
---
arch/arm/boot/dts/stm32mp157-pinctrl.dtsi | 68 +++++++++++++++++++++++++++++++
arch/arm/boot/dts/stm32mp157c-ed1.dts | 37 +++++++++++++++++
2 files changed, 105 insertions(+)
diff --git a/arch/arm/boot/dts/stm32mp157-pinctrl.dtsi b/arch/arm/boot/dts/stm32mp157-pinctrl.dtsi
index 9ec4694..9104896 100644
--- a/arch/arm/boot/dts/stm32mp157-pinctrl.dtsi
+++ b/arch/arm/boot/dts/stm32mp157-pinctrl.dtsi
@@ -325,6 +325,74 @@
};
};
+ sdmmc1_b4_pins_a: sdmmc1-b4-0 {
+ pins {
+ pinmux = <STM32_PINMUX('C', 8, AF12)>, /* SDMMC1_D0 */
+ <STM32_PINMUX('C', 9, AF12)>, /* SDMMC1_D1 */
+ <STM32_PINMUX('C', 10, AF12)>, /* SDMMC1_D2 */
+ <STM32_PINMUX('C', 11, AF12)>, /* SDMMC1_D3 */
+ <STM32_PINMUX('C', 12, AF12)>, /* SDMMC1_CK */
+ <STM32_PINMUX('D', 2, AF12)>; /* SDMMC1_CMD */
+ slew-rate = <3>;
+ drive-push-pull;
+ bias-disable;
+ };
+ };
+
+ sdmmc1_b4_od_pins_a: sdmmc1-b4-od-0 {
+ pins1 {
+ pinmux = <STM32_PINMUX('C', 8, AF12)>, /* SDMMC1_D0 */
+ <STM32_PINMUX('C', 9, AF12)>, /* SDMMC1_D1 */
+ <STM32_PINMUX('C', 10, AF12)>, /* SDMMC1_D2 */
+ <STM32_PINMUX('C', 11, AF12)>, /* SDMMC1_D3 */
+ <STM32_PINMUX('C', 12, AF12)>; /* SDMMC1_CK */
+ slew-rate = <3>;
+ drive-push-pull;
+ bias-disable;
+ };
+ pins2{
+ pinmux = <STM32_PINMUX('D', 2, AF12)>; /* SDMMC1_CMD */
+ slew-rate = <3>;
+ drive-open-drain;
+ bias-disable;
+ };
+ };
+
+ sdmmc1_b4_sleep_pins_a: sdmmc1-b4-sleep-0 {
+ pins {
+ pinmux = <STM32_PINMUX('C', 8, ANALOG)>, /* SDMMC1_D0 */
+ <STM32_PINMUX('C', 9, ANALOG)>, /* SDMMC1_D1 */
+ <STM32_PINMUX('C', 10, ANALOG)>, /* SDMMC1_D2 */
+ <STM32_PINMUX('C', 11, ANALOG)>, /* SDMMC1_D3 */
+ <STM32_PINMUX('C', 12, ANALOG)>, /* SDMMC1_CK */
+ <STM32_PINMUX('D', 2, ANALOG)>; /* SDMMC1_CMD */
+ };
+ };
+
+ sdmmc1_dir_pins_a: sdmmc1-dir-0 {
+ pins1 {
+ pinmux = <STM32_PINMUX('F', 2, AF11)>, /* SDMMC1_D0DIR */
+ <STM32_PINMUX('C', 7, AF8)>, /* SDMMC1_D123DIR */
+ <STM32_PINMUX('B', 9, AF11)>; /* SDMMC1_CDIR */
+ slew-rate = <3>;
+ drive-push-pull;
+ bias-pull-up;
+ };
+ pins2{
+ pinmux = <STM32_PINMUX('E', 4, AF8)>; /* SDMMC1_CKIN */
+ bias-pull-up;
+ };
+ };
+
+ sdmmc1_dir_sleep_pins_a: sdmmc1-dir-sleep-0 {
+ pins {
+ pinmux = <STM32_PINMUX('F', 2, ANALOG)>, /* SDMMC1_D0DIR */
+ <STM32_PINMUX('C', 7, ANALOG)>, /* SDMMC1_D123DIR */
+ <STM32_PINMUX('B', 9, ANALOG)>, /* SDMMC1_CDIR */
+ <STM32_PINMUX('E', 4, ANALOG)>; /* SDMMC1_CKIN */
+ };
+ };
+
uart4_pins_a: uart4-0 {
pins1 {
pinmux = <STM32_PINMUX('G', 11, AF6)>; /* UART4_TX */
diff --git a/arch/arm/boot/dts/stm32mp157c-ed1.dts b/arch/arm/boot/dts/stm32mp157c-ed1.dts
index 98ef7a0..e5cd001 100644
--- a/arch/arm/boot/dts/stm32mp157c-ed1.dts
+++ b/arch/arm/boot/dts/stm32mp157c-ed1.dts
@@ -7,6 +7,7 @@
#include "stm32mp157c.dtsi"
#include "stm32mp157-pinctrl.dtsi"
+#include <dt-bindings/gpio/gpio.h>
/ {
model = "STMicroelectronics STM32MP157C eval daughter";
@@ -40,6 +41,14 @@
regulator-always-on;
};
+ vdd_sd: regulator-vdd_sd {
+ compatible = "regulator-fixed";
+ regulator-name = "vdd_sd";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
vdd_usb: vdd-usb {
compatible = "regulator-fixed";
regulator-name = "vdd_usb";
@@ -47,6 +56,19 @@
regulator-max-microvolt = <3300000>;
regulator-always-on;
};
+
+ sd_switch: regulator-sd_switch {
+ compatible = "regulator-gpio";
+ regulator-name = "sd_switch";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <2900000>;
+ regulator-type = "voltage";
+ regulator-always-on;
+
+ gpios = <&gpiof 14 GPIO_ACTIVE_HIGH>;
+ gpios-states = <0>;
+ states = <1800000 0x1 2900000 0x0>;
+ };
};
&dts {
@@ -84,6 +106,21 @@
};
};
+&sdmmc1 {
+ pinctrl-names = "default", "opendrain", "sleep";
+ pinctrl-0 = <&sdmmc1_b4_pins_a &sdmmc1_dir_pins_a>;
+ pinctrl-1 = <&sdmmc1_b4_od_pins_a &sdmmc1_dir_pins_a>;
+ pinctrl-2 = <&sdmmc1_b4_sleep_pins_a &sdmmc1_dir_sleep_pins_a>;
+ broken-cd;
+ st,sig-dir;
+ st,neg-edge;
+ st,use-ckin;
+ bus-width = <4>;
+ vmmc-supply = <&vdd_sd>;
+ vqmmc-supply = <&sd_switch>;
+ status = "okay";
+};
+
&uart4 {
pinctrl-names = "default";
pinctrl-0 = <&uart4_pins_a>;
--
2.7.4
WARNING: multiple messages have this Message-ID (diff)
From: Ludovic Barre <ludovic.Barre@st.com>
To: Rob Herring <robh+dt@kernel.org>, Mark Rutland <mark.rutland@arm.com>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>,
Alexandre Torgue <alexandre.torgue@st.com>,
devicetree@vger.kernel.org, linux-arm-kernel@lists.infradead.org,
linux-kernel@vger.kernel.org,
linux-stm32@st-md-mailman.stormreply.com,
Ludovic Barre <ludovic.barre@st.com>
Subject: [PATCH 6/7] ARM: dts: stm32: add sdmmc1 support on stm32mp157c ed1 board
Date: Fri, 1 Mar 2019 09:47:47 +0100 [thread overview]
Message-ID: <1551430068-9456-7-git-send-email-ludovic.Barre@st.com> (raw)
In-Reply-To: <1551430068-9456-1-git-send-email-ludovic.Barre@st.com>
From: Ludovic Barre <ludovic.barre@st.com>
This patch adds sdmmc1 support on stm32mp157c ed1 board.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
---
arch/arm/boot/dts/stm32mp157-pinctrl.dtsi | 68 +++++++++++++++++++++++++++++++
arch/arm/boot/dts/stm32mp157c-ed1.dts | 37 +++++++++++++++++
2 files changed, 105 insertions(+)
diff --git a/arch/arm/boot/dts/stm32mp157-pinctrl.dtsi b/arch/arm/boot/dts/stm32mp157-pinctrl.dtsi
index 9ec4694..9104896 100644
--- a/arch/arm/boot/dts/stm32mp157-pinctrl.dtsi
+++ b/arch/arm/boot/dts/stm32mp157-pinctrl.dtsi
@@ -325,6 +325,74 @@
};
};
+ sdmmc1_b4_pins_a: sdmmc1-b4-0 {
+ pins {
+ pinmux = <STM32_PINMUX('C', 8, AF12)>, /* SDMMC1_D0 */
+ <STM32_PINMUX('C', 9, AF12)>, /* SDMMC1_D1 */
+ <STM32_PINMUX('C', 10, AF12)>, /* SDMMC1_D2 */
+ <STM32_PINMUX('C', 11, AF12)>, /* SDMMC1_D3 */
+ <STM32_PINMUX('C', 12, AF12)>, /* SDMMC1_CK */
+ <STM32_PINMUX('D', 2, AF12)>; /* SDMMC1_CMD */
+ slew-rate = <3>;
+ drive-push-pull;
+ bias-disable;
+ };
+ };
+
+ sdmmc1_b4_od_pins_a: sdmmc1-b4-od-0 {
+ pins1 {
+ pinmux = <STM32_PINMUX('C', 8, AF12)>, /* SDMMC1_D0 */
+ <STM32_PINMUX('C', 9, AF12)>, /* SDMMC1_D1 */
+ <STM32_PINMUX('C', 10, AF12)>, /* SDMMC1_D2 */
+ <STM32_PINMUX('C', 11, AF12)>, /* SDMMC1_D3 */
+ <STM32_PINMUX('C', 12, AF12)>; /* SDMMC1_CK */
+ slew-rate = <3>;
+ drive-push-pull;
+ bias-disable;
+ };
+ pins2{
+ pinmux = <STM32_PINMUX('D', 2, AF12)>; /* SDMMC1_CMD */
+ slew-rate = <3>;
+ drive-open-drain;
+ bias-disable;
+ };
+ };
+
+ sdmmc1_b4_sleep_pins_a: sdmmc1-b4-sleep-0 {
+ pins {
+ pinmux = <STM32_PINMUX('C', 8, ANALOG)>, /* SDMMC1_D0 */
+ <STM32_PINMUX('C', 9, ANALOG)>, /* SDMMC1_D1 */
+ <STM32_PINMUX('C', 10, ANALOG)>, /* SDMMC1_D2 */
+ <STM32_PINMUX('C', 11, ANALOG)>, /* SDMMC1_D3 */
+ <STM32_PINMUX('C', 12, ANALOG)>, /* SDMMC1_CK */
+ <STM32_PINMUX('D', 2, ANALOG)>; /* SDMMC1_CMD */
+ };
+ };
+
+ sdmmc1_dir_pins_a: sdmmc1-dir-0 {
+ pins1 {
+ pinmux = <STM32_PINMUX('F', 2, AF11)>, /* SDMMC1_D0DIR */
+ <STM32_PINMUX('C', 7, AF8)>, /* SDMMC1_D123DIR */
+ <STM32_PINMUX('B', 9, AF11)>; /* SDMMC1_CDIR */
+ slew-rate = <3>;
+ drive-push-pull;
+ bias-pull-up;
+ };
+ pins2{
+ pinmux = <STM32_PINMUX('E', 4, AF8)>; /* SDMMC1_CKIN */
+ bias-pull-up;
+ };
+ };
+
+ sdmmc1_dir_sleep_pins_a: sdmmc1-dir-sleep-0 {
+ pins {
+ pinmux = <STM32_PINMUX('F', 2, ANALOG)>, /* SDMMC1_D0DIR */
+ <STM32_PINMUX('C', 7, ANALOG)>, /* SDMMC1_D123DIR */
+ <STM32_PINMUX('B', 9, ANALOG)>, /* SDMMC1_CDIR */
+ <STM32_PINMUX('E', 4, ANALOG)>; /* SDMMC1_CKIN */
+ };
+ };
+
uart4_pins_a: uart4-0 {
pins1 {
pinmux = <STM32_PINMUX('G', 11, AF6)>; /* UART4_TX */
diff --git a/arch/arm/boot/dts/stm32mp157c-ed1.dts b/arch/arm/boot/dts/stm32mp157c-ed1.dts
index 98ef7a0..e5cd001 100644
--- a/arch/arm/boot/dts/stm32mp157c-ed1.dts
+++ b/arch/arm/boot/dts/stm32mp157c-ed1.dts
@@ -7,6 +7,7 @@
#include "stm32mp157c.dtsi"
#include "stm32mp157-pinctrl.dtsi"
+#include <dt-bindings/gpio/gpio.h>
/ {
model = "STMicroelectronics STM32MP157C eval daughter";
@@ -40,6 +41,14 @@
regulator-always-on;
};
+ vdd_sd: regulator-vdd_sd {
+ compatible = "regulator-fixed";
+ regulator-name = "vdd_sd";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
vdd_usb: vdd-usb {
compatible = "regulator-fixed";
regulator-name = "vdd_usb";
@@ -47,6 +56,19 @@
regulator-max-microvolt = <3300000>;
regulator-always-on;
};
+
+ sd_switch: regulator-sd_switch {
+ compatible = "regulator-gpio";
+ regulator-name = "sd_switch";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <2900000>;
+ regulator-type = "voltage";
+ regulator-always-on;
+
+ gpios = <&gpiof 14 GPIO_ACTIVE_HIGH>;
+ gpios-states = <0>;
+ states = <1800000 0x1 2900000 0x0>;
+ };
};
&dts {
@@ -84,6 +106,21 @@
};
};
+&sdmmc1 {
+ pinctrl-names = "default", "opendrain", "sleep";
+ pinctrl-0 = <&sdmmc1_b4_pins_a &sdmmc1_dir_pins_a>;
+ pinctrl-1 = <&sdmmc1_b4_od_pins_a &sdmmc1_dir_pins_a>;
+ pinctrl-2 = <&sdmmc1_b4_sleep_pins_a &sdmmc1_dir_sleep_pins_a>;
+ broken-cd;
+ st,sig-dir;
+ st,neg-edge;
+ st,use-ckin;
+ bus-width = <4>;
+ vmmc-supply = <&vdd_sd>;
+ vqmmc-supply = <&sd_switch>;
+ status = "okay";
+};
+
&uart4 {
pinctrl-names = "default";
pinctrl-0 = <&uart4_pins_a>;
--
2.7.4
WARNING: multiple messages have this Message-ID (diff)
From: Ludovic Barre <ludovic.Barre@st.com>
To: Rob Herring <robh+dt@kernel.org>, Mark Rutland <mark.rutland@arm.com>
Cc: devicetree@vger.kernel.org,
Alexandre Torgue <alexandre.torgue@st.com>,
linux-kernel@vger.kernel.org,
Ludovic Barre <ludovic.barre@st.com>,
Maxime Coquelin <mcoquelin.stm32@gmail.com>,
linux-stm32@st-md-mailman.stormreply.com,
linux-arm-kernel@lists.infradead.org
Subject: [PATCH 6/7] ARM: dts: stm32: add sdmmc1 support on stm32mp157c ed1 board
Date: Fri, 1 Mar 2019 09:47:47 +0100 [thread overview]
Message-ID: <1551430068-9456-7-git-send-email-ludovic.Barre@st.com> (raw)
In-Reply-To: <1551430068-9456-1-git-send-email-ludovic.Barre@st.com>
From: Ludovic Barre <ludovic.barre@st.com>
This patch adds sdmmc1 support on stm32mp157c ed1 board.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
---
arch/arm/boot/dts/stm32mp157-pinctrl.dtsi | 68 +++++++++++++++++++++++++++++++
arch/arm/boot/dts/stm32mp157c-ed1.dts | 37 +++++++++++++++++
2 files changed, 105 insertions(+)
diff --git a/arch/arm/boot/dts/stm32mp157-pinctrl.dtsi b/arch/arm/boot/dts/stm32mp157-pinctrl.dtsi
index 9ec4694..9104896 100644
--- a/arch/arm/boot/dts/stm32mp157-pinctrl.dtsi
+++ b/arch/arm/boot/dts/stm32mp157-pinctrl.dtsi
@@ -325,6 +325,74 @@
};
};
+ sdmmc1_b4_pins_a: sdmmc1-b4-0 {
+ pins {
+ pinmux = <STM32_PINMUX('C', 8, AF12)>, /* SDMMC1_D0 */
+ <STM32_PINMUX('C', 9, AF12)>, /* SDMMC1_D1 */
+ <STM32_PINMUX('C', 10, AF12)>, /* SDMMC1_D2 */
+ <STM32_PINMUX('C', 11, AF12)>, /* SDMMC1_D3 */
+ <STM32_PINMUX('C', 12, AF12)>, /* SDMMC1_CK */
+ <STM32_PINMUX('D', 2, AF12)>; /* SDMMC1_CMD */
+ slew-rate = <3>;
+ drive-push-pull;
+ bias-disable;
+ };
+ };
+
+ sdmmc1_b4_od_pins_a: sdmmc1-b4-od-0 {
+ pins1 {
+ pinmux = <STM32_PINMUX('C', 8, AF12)>, /* SDMMC1_D0 */
+ <STM32_PINMUX('C', 9, AF12)>, /* SDMMC1_D1 */
+ <STM32_PINMUX('C', 10, AF12)>, /* SDMMC1_D2 */
+ <STM32_PINMUX('C', 11, AF12)>, /* SDMMC1_D3 */
+ <STM32_PINMUX('C', 12, AF12)>; /* SDMMC1_CK */
+ slew-rate = <3>;
+ drive-push-pull;
+ bias-disable;
+ };
+ pins2{
+ pinmux = <STM32_PINMUX('D', 2, AF12)>; /* SDMMC1_CMD */
+ slew-rate = <3>;
+ drive-open-drain;
+ bias-disable;
+ };
+ };
+
+ sdmmc1_b4_sleep_pins_a: sdmmc1-b4-sleep-0 {
+ pins {
+ pinmux = <STM32_PINMUX('C', 8, ANALOG)>, /* SDMMC1_D0 */
+ <STM32_PINMUX('C', 9, ANALOG)>, /* SDMMC1_D1 */
+ <STM32_PINMUX('C', 10, ANALOG)>, /* SDMMC1_D2 */
+ <STM32_PINMUX('C', 11, ANALOG)>, /* SDMMC1_D3 */
+ <STM32_PINMUX('C', 12, ANALOG)>, /* SDMMC1_CK */
+ <STM32_PINMUX('D', 2, ANALOG)>; /* SDMMC1_CMD */
+ };
+ };
+
+ sdmmc1_dir_pins_a: sdmmc1-dir-0 {
+ pins1 {
+ pinmux = <STM32_PINMUX('F', 2, AF11)>, /* SDMMC1_D0DIR */
+ <STM32_PINMUX('C', 7, AF8)>, /* SDMMC1_D123DIR */
+ <STM32_PINMUX('B', 9, AF11)>; /* SDMMC1_CDIR */
+ slew-rate = <3>;
+ drive-push-pull;
+ bias-pull-up;
+ };
+ pins2{
+ pinmux = <STM32_PINMUX('E', 4, AF8)>; /* SDMMC1_CKIN */
+ bias-pull-up;
+ };
+ };
+
+ sdmmc1_dir_sleep_pins_a: sdmmc1-dir-sleep-0 {
+ pins {
+ pinmux = <STM32_PINMUX('F', 2, ANALOG)>, /* SDMMC1_D0DIR */
+ <STM32_PINMUX('C', 7, ANALOG)>, /* SDMMC1_D123DIR */
+ <STM32_PINMUX('B', 9, ANALOG)>, /* SDMMC1_CDIR */
+ <STM32_PINMUX('E', 4, ANALOG)>; /* SDMMC1_CKIN */
+ };
+ };
+
uart4_pins_a: uart4-0 {
pins1 {
pinmux = <STM32_PINMUX('G', 11, AF6)>; /* UART4_TX */
diff --git a/arch/arm/boot/dts/stm32mp157c-ed1.dts b/arch/arm/boot/dts/stm32mp157c-ed1.dts
index 98ef7a0..e5cd001 100644
--- a/arch/arm/boot/dts/stm32mp157c-ed1.dts
+++ b/arch/arm/boot/dts/stm32mp157c-ed1.dts
@@ -7,6 +7,7 @@
#include "stm32mp157c.dtsi"
#include "stm32mp157-pinctrl.dtsi"
+#include <dt-bindings/gpio/gpio.h>
/ {
model = "STMicroelectronics STM32MP157C eval daughter";
@@ -40,6 +41,14 @@
regulator-always-on;
};
+ vdd_sd: regulator-vdd_sd {
+ compatible = "regulator-fixed";
+ regulator-name = "vdd_sd";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
vdd_usb: vdd-usb {
compatible = "regulator-fixed";
regulator-name = "vdd_usb";
@@ -47,6 +56,19 @@
regulator-max-microvolt = <3300000>;
regulator-always-on;
};
+
+ sd_switch: regulator-sd_switch {
+ compatible = "regulator-gpio";
+ regulator-name = "sd_switch";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <2900000>;
+ regulator-type = "voltage";
+ regulator-always-on;
+
+ gpios = <&gpiof 14 GPIO_ACTIVE_HIGH>;
+ gpios-states = <0>;
+ states = <1800000 0x1 2900000 0x0>;
+ };
};
&dts {
@@ -84,6 +106,21 @@
};
};
+&sdmmc1 {
+ pinctrl-names = "default", "opendrain", "sleep";
+ pinctrl-0 = <&sdmmc1_b4_pins_a &sdmmc1_dir_pins_a>;
+ pinctrl-1 = <&sdmmc1_b4_od_pins_a &sdmmc1_dir_pins_a>;
+ pinctrl-2 = <&sdmmc1_b4_sleep_pins_a &sdmmc1_dir_sleep_pins_a>;
+ broken-cd;
+ st,sig-dir;
+ st,neg-edge;
+ st,use-ckin;
+ bus-width = <4>;
+ vmmc-supply = <&vdd_sd>;
+ vqmmc-supply = <&sd_switch>;
+ status = "okay";
+};
+
&uart4 {
pinctrl-names = "default";
pinctrl-0 = <&uart4_pins_a>;
--
2.7.4
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
next prev parent reply other threads:[~2019-03-01 8:48 UTC|newest]
Thread overview: 27+ messages / expand[flat|nested] mbox.gz Atom feed top
2019-03-01 8:47 [PATCH 0/7] ARM: dts: stm32: add support of sdmmc1 on stm32 Ludovic Barre
2019-03-01 8:47 ` Ludovic Barre
2019-03-01 8:47 ` Ludovic Barre
2019-03-01 8:47 ` [PATCH 1/7] ARM: stm32: add AMBA support for stm32 family Ludovic Barre
2019-03-01 8:47 ` Ludovic Barre
2019-03-01 8:47 ` Ludovic Barre
2019-03-01 8:47 ` [PATCH 2/7] ARM: dts: stm32: add sdmmc1 support on stm32h743 Ludovic Barre
2019-03-01 8:47 ` Ludovic Barre
2019-03-01 8:47 ` Ludovic Barre
2019-03-01 8:47 ` [PATCH 3/7] ARM: dts: stm32: add sdmmc1 support on stm32h743i eval board Ludovic Barre
2019-03-01 8:47 ` Ludovic Barre
2019-03-01 8:47 ` Ludovic Barre
2019-03-01 8:47 ` [PATCH 4/7] ARM: dts: stm32: add sdmmc1 support on stm32h743i disco board Ludovic Barre
2019-03-01 8:47 ` Ludovic Barre
2019-03-01 8:47 ` Ludovic Barre
2019-03-01 8:47 ` [PATCH 5/7] ARM: dts: stm32: add sdmmc1 support on stm32mp157c Ludovic Barre
2019-03-01 8:47 ` Ludovic Barre
2019-03-01 8:47 ` Ludovic Barre
2019-03-01 8:47 ` Ludovic Barre [this message]
2019-03-01 8:47 ` [PATCH 6/7] ARM: dts: stm32: add sdmmc1 support on stm32mp157c ed1 board Ludovic Barre
2019-03-01 8:47 ` Ludovic Barre
2019-03-01 8:47 ` [PATCH 7/7] ARM: dts: stm32: add sdmmc1 support on stm32mp157a dk1 board Ludovic Barre
2019-03-01 8:47 ` Ludovic Barre
2019-03-01 8:47 ` Ludovic Barre
2019-03-26 10:22 ` [PATCH 0/7] ARM: dts: stm32: add support of sdmmc1 on stm32 Alexandre Torgue
2019-03-26 10:22 ` Alexandre Torgue
2019-03-26 10:22 ` Alexandre Torgue
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1551430068-9456-7-git-send-email-ludovic.Barre@st.com \
--to=ludovic.barre@st.com \
--cc=alexandre.torgue@st.com \
--cc=devicetree@vger.kernel.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-stm32@st-md-mailman.stormreply.com \
--cc=mark.rutland@arm.com \
--cc=mcoquelin.stm32@gmail.com \
--cc=robh+dt@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.