All of lore.kernel.org
 help / color / mirror / Atom feed
From: Anson.Huang@nxp.com
To: robh+dt@kernel.org, mark.rutland@arm.com, shawnguo@kernel.org,
	s.hauer@pengutronix.de, kernel@pengutronix.de,
	festevam@gmail.com, mturquette@baylibre.com, sboyd@kernel.org,
	rjw@rjwysocki.net, viresh.kumar@linaro.org,
	leonard.crestez@nxp.com, abel.vesa@nxp.com,
	devicetree@vger.kernel.org, linux-arm-kernel@lists.infradead.org,
	linux-kernel@vger.kernel.org, linux-clk@vger.kernel.org,
	linux-pm@vger.kernel.org
Cc: Linux-imx@nxp.com
Subject: [PATCH 2/6] arm64: dts: imx8mn-ddr4-evk: Add rohm,bd71847 PMIC support
Date: Thu, 15 Aug 2019 06:59:39 -0400	[thread overview]
Message-ID: <1565866783-19672-2-git-send-email-Anson.Huang@nxp.com> (raw)
In-Reply-To: <1565866783-19672-1-git-send-email-Anson.Huang@nxp.com>

From: Anson Huang <Anson.Huang@nxp.com>

On i.MX8MN DDR4 EVK board, there is a rohm,bd71847 PMIC
on i2c1 bus, enable it.

Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
---
 arch/arm64/boot/dts/freescale/imx8mn-ddr4-evk.dts | 109 ++++++++++++++++++++++
 1 file changed, 109 insertions(+)

diff --git a/arch/arm64/boot/dts/freescale/imx8mn-ddr4-evk.dts b/arch/arm64/boot/dts/freescale/imx8mn-ddr4-evk.dts
index 5fce5b1..10ebf77 100644
--- a/arch/arm64/boot/dts/freescale/imx8mn-ddr4-evk.dts
+++ b/arch/arm64/boot/dts/freescale/imx8mn-ddr4-evk.dts
@@ -57,6 +57,12 @@
 		>;
 	};
 
+	pinctrl_pmic: pmicirq {
+		fsl,pins = <
+			MX8MN_IOMUXC_GPIO1_IO03_GPIO1_IO3	0x41
+		>;
+	};
+
 	pinctrl_reg_usdhc2_vmmc: regusdhc2vmmc {
 		fsl,pins = <
 			MX8MN_IOMUXC_SD2_RESET_B_GPIO2_IO19	0x41
@@ -194,6 +200,109 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_i2c1>;
 	status = "okay";
+
+	pmic@4b {
+		compatible = "rohm,bd71847";
+		reg = <0x4b>;
+		pinctrl-0 = <&pinctrl_pmic>;
+		interrupt-parent = <&gpio1>;
+		interrupts = <3 GPIO_ACTIVE_LOW>;
+		rohm,reset-snvs-powered;
+
+		regulators {
+			buck1_reg: BUCK1 {
+				regulator-name = "BUCK1";
+				regulator-min-microvolt = <700000>;
+				regulator-max-microvolt = <1300000>;
+				regulator-boot-on;
+				regulator-always-on;
+				regulator-ramp-delay = <1250>;
+			};
+
+			buck2_reg: BUCK2 {
+				regulator-name = "BUCK2";
+				regulator-min-microvolt = <700000>;
+				regulator-max-microvolt = <1300000>;
+				regulator-boot-on;
+				regulator-always-on;
+				regulator-ramp-delay = <1250>;
+			};
+
+			buck3_reg: BUCK3 {
+				// BUCK5 in datasheet
+				regulator-name = "BUCK3";
+				regulator-min-microvolt = <700000>;
+				regulator-max-microvolt = <1350000>;
+			};
+
+			buck4_reg: BUCK4 {
+				// BUCK6 in datasheet
+				regulator-name = "BUCK4";
+				regulator-min-microvolt = <3000000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			buck5_reg: BUCK5 {
+				// BUCK7 in datasheet
+				regulator-name = "BUCK5";
+				regulator-min-microvolt = <1605000>;
+				regulator-max-microvolt = <1995000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			buck6_reg: BUCK6 {
+				// BUCK8 in datasheet
+				regulator-name = "BUCK6";
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <1400000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			ldo1_reg: LDO1 {
+				regulator-name = "LDO1";
+				regulator-min-microvolt = <3000000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			ldo2_reg: LDO2 {
+				regulator-name = "LDO2";
+				regulator-min-microvolt = <900000>;
+				regulator-max-microvolt = <900000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			ldo3_reg: LDO3 {
+				regulator-name = "LDO3";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			ldo4_reg: LDO4 {
+				regulator-name = "LDO4";
+				regulator-min-microvolt = <900000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			ldo6_reg: LDO6 {
+				regulator-name = "LDO6";
+				regulator-min-microvolt = <900000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+		};
+	};
 };
 
 &snvs_pwrkey {
-- 
2.7.4


WARNING: multiple messages have this Message-ID (diff)
From: Anson.Huang@nxp.com
To: robh+dt@kernel.org, mark.rutland@arm.com, shawnguo@kernel.org,
	s.hauer@pengutronix.de, kernel@pengutronix.de,
	festevam@gmail.com, mturquette@baylibre.com, sboyd@kernel.org,
	rjw@rjwysocki.net, viresh.kumar@linaro.org,
	leonard.crestez@nxp.com, abel.vesa@nxp.com,
	devicetree@vger.kernel.org, linux-arm-kernel@lists.infradead.org,
	linux-kernel@vger.kernel.org, linux-clk@vger.kernel.org,
	linux-pm@vger.kernel.org
Cc: Linux-imx@nxp.com
Subject: [PATCH 2/6] arm64: dts: imx8mn-ddr4-evk: Add rohm, bd71847 PMIC support
Date: Thu, 15 Aug 2019 06:59:39 -0400	[thread overview]
Message-ID: <1565866783-19672-2-git-send-email-Anson.Huang@nxp.com> (raw)
In-Reply-To: <1565866783-19672-1-git-send-email-Anson.Huang@nxp.com>

From: Anson Huang <Anson.Huang@nxp.com>

On i.MX8MN DDR4 EVK board, there is a rohm,bd71847 PMIC
on i2c1 bus, enable it.

Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
---
 arch/arm64/boot/dts/freescale/imx8mn-ddr4-evk.dts | 109 ++++++++++++++++++++++
 1 file changed, 109 insertions(+)

diff --git a/arch/arm64/boot/dts/freescale/imx8mn-ddr4-evk.dts b/arch/arm64/boot/dts/freescale/imx8mn-ddr4-evk.dts
index 5fce5b1..10ebf77 100644
--- a/arch/arm64/boot/dts/freescale/imx8mn-ddr4-evk.dts
+++ b/arch/arm64/boot/dts/freescale/imx8mn-ddr4-evk.dts
@@ -57,6 +57,12 @@
 		>;
 	};
 
+	pinctrl_pmic: pmicirq {
+		fsl,pins = <
+			MX8MN_IOMUXC_GPIO1_IO03_GPIO1_IO3	0x41
+		>;
+	};
+
 	pinctrl_reg_usdhc2_vmmc: regusdhc2vmmc {
 		fsl,pins = <
 			MX8MN_IOMUXC_SD2_RESET_B_GPIO2_IO19	0x41
@@ -194,6 +200,109 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_i2c1>;
 	status = "okay";
+
+	pmic@4b {
+		compatible = "rohm,bd71847";
+		reg = <0x4b>;
+		pinctrl-0 = <&pinctrl_pmic>;
+		interrupt-parent = <&gpio1>;
+		interrupts = <3 GPIO_ACTIVE_LOW>;
+		rohm,reset-snvs-powered;
+
+		regulators {
+			buck1_reg: BUCK1 {
+				regulator-name = "BUCK1";
+				regulator-min-microvolt = <700000>;
+				regulator-max-microvolt = <1300000>;
+				regulator-boot-on;
+				regulator-always-on;
+				regulator-ramp-delay = <1250>;
+			};
+
+			buck2_reg: BUCK2 {
+				regulator-name = "BUCK2";
+				regulator-min-microvolt = <700000>;
+				regulator-max-microvolt = <1300000>;
+				regulator-boot-on;
+				regulator-always-on;
+				regulator-ramp-delay = <1250>;
+			};
+
+			buck3_reg: BUCK3 {
+				// BUCK5 in datasheet
+				regulator-name = "BUCK3";
+				regulator-min-microvolt = <700000>;
+				regulator-max-microvolt = <1350000>;
+			};
+
+			buck4_reg: BUCK4 {
+				// BUCK6 in datasheet
+				regulator-name = "BUCK4";
+				regulator-min-microvolt = <3000000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			buck5_reg: BUCK5 {
+				// BUCK7 in datasheet
+				regulator-name = "BUCK5";
+				regulator-min-microvolt = <1605000>;
+				regulator-max-microvolt = <1995000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			buck6_reg: BUCK6 {
+				// BUCK8 in datasheet
+				regulator-name = "BUCK6";
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <1400000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			ldo1_reg: LDO1 {
+				regulator-name = "LDO1";
+				regulator-min-microvolt = <3000000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			ldo2_reg: LDO2 {
+				regulator-name = "LDO2";
+				regulator-min-microvolt = <900000>;
+				regulator-max-microvolt = <900000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			ldo3_reg: LDO3 {
+				regulator-name = "LDO3";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			ldo4_reg: LDO4 {
+				regulator-name = "LDO4";
+				regulator-min-microvolt = <900000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			ldo6_reg: LDO6 {
+				regulator-name = "LDO6";
+				regulator-min-microvolt = <900000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+		};
+	};
 };
 
 &snvs_pwrkey {
-- 
2.7.4


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

  reply	other threads:[~2019-08-15 11:18 UTC|newest]

Thread overview: 26+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2019-08-15 10:59 [PATCH 1/6] arm64: dts: imx8mn-ddr4-evk: Add i2c1 support Anson.Huang
2019-08-15 10:59 ` Anson.Huang
2019-08-15 10:59 ` Anson.Huang [this message]
2019-08-15 10:59   ` [PATCH 2/6] arm64: dts: imx8mn-ddr4-evk: Add rohm, bd71847 PMIC support Anson.Huang
2019-08-15 10:59 ` [PATCH 3/6] cpufreq: Use imx-cpufreq-dt for i.MX8MN's speed grading Anson.Huang
2019-08-15 10:59   ` Anson.Huang
2019-08-15 10:59 ` [PATCH 4/6] cpufreq: imx-cpufreq-dt: Add i.MX8MN support Anson.Huang
2019-08-15 10:59   ` Anson.Huang
2019-08-15 10:59 ` [PATCH 5/6] clk: imx8mn: Add necessary frequency support for ARM PLL table Anson.Huang
2019-08-15 10:59   ` Anson.Huang
2019-08-17  3:52   ` Stephen Boyd
2019-08-17  3:52     ` Stephen Boyd
2019-08-17 22:22     ` Anson Huang
2019-08-17 22:22       ` Anson Huang
2019-08-17 22:22       ` Anson Huang
2019-08-18  1:11       ` Stephen Boyd
2019-08-18  1:11         ` Stephen Boyd
2019-08-18  1:11         ` Stephen Boyd
2019-08-18  6:19         ` Anson Huang
2019-08-18  6:19           ` Anson Huang
2019-08-18  6:19           ` Anson Huang
2019-08-15 10:59 ` [PATCH 6/6] arm64: dts: imx8mn: Add cpu-freq support Anson.Huang
2019-08-15 10:59   ` Anson.Huang
2019-08-15 14:12 ` [PATCH 1/6] arm64: dts: imx8mn-ddr4-evk: Add i2c1 support Leonard Crestez
2019-08-15 14:12   ` Leonard Crestez
2019-08-15 14:12   ` Leonard Crestez

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=1565866783-19672-2-git-send-email-Anson.Huang@nxp.com \
    --to=anson.huang@nxp.com \
    --cc=Linux-imx@nxp.com \
    --cc=abel.vesa@nxp.com \
    --cc=devicetree@vger.kernel.org \
    --cc=festevam@gmail.com \
    --cc=kernel@pengutronix.de \
    --cc=leonard.crestez@nxp.com \
    --cc=linux-arm-kernel@lists.infradead.org \
    --cc=linux-clk@vger.kernel.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=linux-pm@vger.kernel.org \
    --cc=mark.rutland@arm.com \
    --cc=mturquette@baylibre.com \
    --cc=rjw@rjwysocki.net \
    --cc=robh+dt@kernel.org \
    --cc=s.hauer@pengutronix.de \
    --cc=sboyd@kernel.org \
    --cc=shawnguo@kernel.org \
    --cc=viresh.kumar@linaro.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body. 
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.