From: Anson Huang <Anson.Huang@nxp.com> To: robh+dt@kernel.org, mark.rutland@arm.com, shawnguo@kernel.org, s.hauer@pengutronix.de, kernel@pengutronix.de, festevam@gmail.com, mturquette@baylibre.com, sboyd@kernel.org, rjw@rjwysocki.net, viresh.kumar@linaro.org, leonard.crestez@nxp.com, abel.vesa@nxp.com, devicetree@vger.kernel.org, linux-arm-kernel@lists.infradead.org, linux-kernel@vger.kernel.org, linux-clk@vger.kernel.org, linux-pm@vger.kernel.org Cc: Linux-imx@nxp.com Subject: [PATCH V2 2/6] arm64: dts: imx8mn-ddr4-evk: Add rohm,bd71847 PMIC support Date: Sat, 17 Aug 2019 18:28:16 -0400 [thread overview] Message-ID: <1566080900-2539-2-git-send-email-Anson.Huang@nxp.com> (raw) In-Reply-To: <1566080900-2539-1-git-send-email-Anson.Huang@nxp.com> On i.MX8MN DDR4 EVK board, there is a rohm,bd71847 PMIC on i2c1 bus, enable it. Signed-off-by: Anson Huang <Anson.Huang@nxp.com> --- No changes. --- arch/arm64/boot/dts/freescale/imx8mn-ddr4-evk.dts | 109 ++++++++++++++++++++++ 1 file changed, 109 insertions(+) diff --git a/arch/arm64/boot/dts/freescale/imx8mn-ddr4-evk.dts b/arch/arm64/boot/dts/freescale/imx8mn-ddr4-evk.dts index 5fce5b1..10ebf77 100644 --- a/arch/arm64/boot/dts/freescale/imx8mn-ddr4-evk.dts +++ b/arch/arm64/boot/dts/freescale/imx8mn-ddr4-evk.dts @@ -57,6 +57,12 @@ >; }; + pinctrl_pmic: pmicirq { + fsl,pins = < + MX8MN_IOMUXC_GPIO1_IO03_GPIO1_IO3 0x41 + >; + }; + pinctrl_reg_usdhc2_vmmc: regusdhc2vmmc { fsl,pins = < MX8MN_IOMUXC_SD2_RESET_B_GPIO2_IO19 0x41 @@ -194,6 +200,109 @@ pinctrl-names = "default"; pinctrl-0 = <&pinctrl_i2c1>; status = "okay"; + + pmic@4b { + compatible = "rohm,bd71847"; + reg = <0x4b>; + pinctrl-0 = <&pinctrl_pmic>; + interrupt-parent = <&gpio1>; + interrupts = <3 GPIO_ACTIVE_LOW>; + rohm,reset-snvs-powered; + + regulators { + buck1_reg: BUCK1 { + regulator-name = "BUCK1"; + regulator-min-microvolt = <700000>; + regulator-max-microvolt = <1300000>; + regulator-boot-on; + regulator-always-on; + regulator-ramp-delay = <1250>; + }; + + buck2_reg: BUCK2 { + regulator-name = "BUCK2"; + regulator-min-microvolt = <700000>; + regulator-max-microvolt = <1300000>; + regulator-boot-on; + regulator-always-on; + regulator-ramp-delay = <1250>; + }; + + buck3_reg: BUCK3 { + // BUCK5 in datasheet + regulator-name = "BUCK3"; + regulator-min-microvolt = <700000>; + regulator-max-microvolt = <1350000>; + }; + + buck4_reg: BUCK4 { + // BUCK6 in datasheet + regulator-name = "BUCK4"; + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + regulator-always-on; + }; + + buck5_reg: BUCK5 { + // BUCK7 in datasheet + regulator-name = "BUCK5"; + regulator-min-microvolt = <1605000>; + regulator-max-microvolt = <1995000>; + regulator-boot-on; + regulator-always-on; + }; + + buck6_reg: BUCK6 { + // BUCK8 in datasheet + regulator-name = "BUCK6"; + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <1400000>; + regulator-boot-on; + regulator-always-on; + }; + + ldo1_reg: LDO1 { + regulator-name = "LDO1"; + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + regulator-always-on; + }; + + ldo2_reg: LDO2 { + regulator-name = "LDO2"; + regulator-min-microvolt = <900000>; + regulator-max-microvolt = <900000>; + regulator-boot-on; + regulator-always-on; + }; + + ldo3_reg: LDO3 { + regulator-name = "LDO3"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + regulator-always-on; + }; + + ldo4_reg: LDO4 { + regulator-name = "LDO4"; + regulator-min-microvolt = <900000>; + regulator-max-microvolt = <1800000>; + regulator-boot-on; + regulator-always-on; + }; + + ldo6_reg: LDO6 { + regulator-name = "LDO6"; + regulator-min-microvolt = <900000>; + regulator-max-microvolt = <1800000>; + regulator-boot-on; + regulator-always-on; + }; + }; + }; }; &snvs_pwrkey { -- 2.7.4
WARNING: multiple messages have this Message-ID (diff)
From: Anson Huang <Anson.Huang@nxp.com> To: robh+dt@kernel.org, mark.rutland@arm.com, shawnguo@kernel.org, s.hauer@pengutronix.de, kernel@pengutronix.de, festevam@gmail.com, mturquette@baylibre.com, sboyd@kernel.org, rjw@rjwysocki.net, viresh.kumar@linaro.org, leonard.crestez@nxp.com, abel.vesa@nxp.com, devicetree@vger.kernel.org, linux-arm-kernel@lists.infradead.org, linux-kernel@vger.kernel.org, linux-clk@vger.kernel.org, linux-pm@vger.kernel.org Cc: Linux-imx@nxp.com Subject: [PATCH V2 2/6] arm64: dts: imx8mn-ddr4-evk: Add rohm, bd71847 PMIC support Date: Sat, 17 Aug 2019 18:28:16 -0400 [thread overview] Message-ID: <1566080900-2539-2-git-send-email-Anson.Huang@nxp.com> (raw) In-Reply-To: <1566080900-2539-1-git-send-email-Anson.Huang@nxp.com> On i.MX8MN DDR4 EVK board, there is a rohm,bd71847 PMIC on i2c1 bus, enable it. Signed-off-by: Anson Huang <Anson.Huang@nxp.com> --- No changes. --- arch/arm64/boot/dts/freescale/imx8mn-ddr4-evk.dts | 109 ++++++++++++++++++++++ 1 file changed, 109 insertions(+) diff --git a/arch/arm64/boot/dts/freescale/imx8mn-ddr4-evk.dts b/arch/arm64/boot/dts/freescale/imx8mn-ddr4-evk.dts index 5fce5b1..10ebf77 100644 --- a/arch/arm64/boot/dts/freescale/imx8mn-ddr4-evk.dts +++ b/arch/arm64/boot/dts/freescale/imx8mn-ddr4-evk.dts @@ -57,6 +57,12 @@ >; }; + pinctrl_pmic: pmicirq { + fsl,pins = < + MX8MN_IOMUXC_GPIO1_IO03_GPIO1_IO3 0x41 + >; + }; + pinctrl_reg_usdhc2_vmmc: regusdhc2vmmc { fsl,pins = < MX8MN_IOMUXC_SD2_RESET_B_GPIO2_IO19 0x41 @@ -194,6 +200,109 @@ pinctrl-names = "default"; pinctrl-0 = <&pinctrl_i2c1>; status = "okay"; + + pmic@4b { + compatible = "rohm,bd71847"; + reg = <0x4b>; + pinctrl-0 = <&pinctrl_pmic>; + interrupt-parent = <&gpio1>; + interrupts = <3 GPIO_ACTIVE_LOW>; + rohm,reset-snvs-powered; + + regulators { + buck1_reg: BUCK1 { + regulator-name = "BUCK1"; + regulator-min-microvolt = <700000>; + regulator-max-microvolt = <1300000>; + regulator-boot-on; + regulator-always-on; + regulator-ramp-delay = <1250>; + }; + + buck2_reg: BUCK2 { + regulator-name = "BUCK2"; + regulator-min-microvolt = <700000>; + regulator-max-microvolt = <1300000>; + regulator-boot-on; + regulator-always-on; + regulator-ramp-delay = <1250>; + }; + + buck3_reg: BUCK3 { + // BUCK5 in datasheet + regulator-name = "BUCK3"; + regulator-min-microvolt = <700000>; + regulator-max-microvolt = <1350000>; + }; + + buck4_reg: BUCK4 { + // BUCK6 in datasheet + regulator-name = "BUCK4"; + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + regulator-always-on; + }; + + buck5_reg: BUCK5 { + // BUCK7 in datasheet + regulator-name = "BUCK5"; + regulator-min-microvolt = <1605000>; + regulator-max-microvolt = <1995000>; + regulator-boot-on; + regulator-always-on; + }; + + buck6_reg: BUCK6 { + // BUCK8 in datasheet + regulator-name = "BUCK6"; + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <1400000>; + regulator-boot-on; + regulator-always-on; + }; + + ldo1_reg: LDO1 { + regulator-name = "LDO1"; + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + regulator-always-on; + }; + + ldo2_reg: LDO2 { + regulator-name = "LDO2"; + regulator-min-microvolt = <900000>; + regulator-max-microvolt = <900000>; + regulator-boot-on; + regulator-always-on; + }; + + ldo3_reg: LDO3 { + regulator-name = "LDO3"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + regulator-always-on; + }; + + ldo4_reg: LDO4 { + regulator-name = "LDO4"; + regulator-min-microvolt = <900000>; + regulator-max-microvolt = <1800000>; + regulator-boot-on; + regulator-always-on; + }; + + ldo6_reg: LDO6 { + regulator-name = "LDO6"; + regulator-min-microvolt = <900000>; + regulator-max-microvolt = <1800000>; + regulator-boot-on; + regulator-always-on; + }; + }; + }; }; &snvs_pwrkey { -- 2.7.4 _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
next prev parent reply other threads:[~2019-08-17 22:47 UTC|newest] Thread overview: 12+ messages / expand[flat|nested] mbox.gz Atom feed top 2019-08-17 22:28 [PATCH V2 1/6] arm64: dts: imx8mn-ddr4-evk: Add i2c1 support Anson Huang 2019-08-17 22:28 ` Anson Huang 2019-08-17 22:28 ` Anson Huang [this message] 2019-08-17 22:28 ` [PATCH V2 2/6] arm64: dts: imx8mn-ddr4-evk: Add rohm, bd71847 PMIC support Anson Huang 2019-08-17 22:28 ` [PATCH V2 3/6] cpufreq: Use imx-cpufreq-dt for i.MX8MN's speed grading Anson Huang 2019-08-17 22:28 ` Anson Huang 2019-08-17 22:28 ` [PATCH V2 4/6] cpufreq: imx-cpufreq-dt: Add i.MX8MN support Anson Huang 2019-08-17 22:28 ` Anson Huang 2019-08-17 22:28 ` [PATCH V2 5/6] clk: imx8mn: Improve ARM PLL table to support CPU frequency scaling Anson Huang 2019-08-17 22:28 ` Anson Huang 2019-08-17 22:28 ` [PATCH V2 6/6] arm64: dts: imx8mn: Add cpu-freq support Anson Huang 2019-08-17 22:28 ` Anson Huang
Reply instructions: You may reply publicly to this message via plain-text email using any one of the following methods: * Save the following mbox file, import it into your mail client, and reply-to-all from there: mbox Avoid top-posting and favor interleaved quoting: https://en.wikipedia.org/wiki/Posting_style#Interleaved_style * Reply using the --to, --cc, and --in-reply-to switches of git-send-email(1): git send-email \ --in-reply-to=1566080900-2539-2-git-send-email-Anson.Huang@nxp.com \ --to=anson.huang@nxp.com \ --cc=Linux-imx@nxp.com \ --cc=abel.vesa@nxp.com \ --cc=devicetree@vger.kernel.org \ --cc=festevam@gmail.com \ --cc=kernel@pengutronix.de \ --cc=leonard.crestez@nxp.com \ --cc=linux-arm-kernel@lists.infradead.org \ --cc=linux-clk@vger.kernel.org \ --cc=linux-kernel@vger.kernel.org \ --cc=linux-pm@vger.kernel.org \ --cc=mark.rutland@arm.com \ --cc=mturquette@baylibre.com \ --cc=rjw@rjwysocki.net \ --cc=robh+dt@kernel.org \ --cc=s.hauer@pengutronix.de \ --cc=sboyd@kernel.org \ --cc=shawnguo@kernel.org \ --cc=viresh.kumar@linaro.org \ /path/to/YOUR_REPLY https://kernel.org/pub/software/scm/git/docs/git-send-email.html * If your mail client supports setting the In-Reply-To header via mailto: links, try the mailto: linkBe sure your reply has a Subject: header at the top and a blank line before the message body.
This is an external index of several public inboxes, see mirroring instructions on how to clone and mirror all data and code used by this external index.