All of lore.kernel.org
 help / color / mirror / Atom feed
From: Sandeep Maheswaram <sanm@codeaurora.org>
To: Andy Gross <agross@kernel.org>,
	Bjorn Andersson <bjorn.andersson@linaro.org>,
	Kishon Vijay Abraham I <kishon@ti.com>,
	Rob Herring <robh+dt@kernel.org>,
	Mark Rutland <mark.rutland@arm.com>,
	Stephen Boyd <swboyd@chromium.org>
Cc: linux-arm-msm@vger.kernel.org, linux-kernel@vger.kernel.org,
	devicetree@vger.kernel.org, Manu Gautam <mgautam@codeaurora.org>,
	Sandeep Maheswaram <sanm@codeaurora.org>
Subject: [PATCH v2 3/3] dt-bindings: phy: qcom-qusb2: Add SC7180 QUSB2 phy support
Date: Thu,  5 Dec 2019 10:11:21 +0530	[thread overview]
Message-ID: <1575520881-31458-4-git-send-email-sanm@codeaurora.org> (raw)
In-Reply-To: <1575520881-31458-1-git-send-email-sanm@codeaurora.org>

Add QUSB2 phy entries for SC7180 in device tree bindings.

Signed-off-by: Sandeep Maheswaram <sanm@codeaurora.org>
---
 Documentation/devicetree/bindings/phy/qcom-qusb2-phy.yaml | 9 +++++----
 1 file changed, 5 insertions(+), 4 deletions(-)

diff --git a/Documentation/devicetree/bindings/phy/qcom-qusb2-phy.yaml b/Documentation/devicetree/bindings/phy/qcom-qusb2-phy.yaml
index 3ef94bc..5eff9016 100644
--- a/Documentation/devicetree/bindings/phy/qcom-qusb2-phy.yaml
+++ b/Documentation/devicetree/bindings/phy/qcom-qusb2-phy.yaml
@@ -18,6 +18,7 @@ properties:
     enum:
       - qcom,msm8996-qusb2-phy
       - qcom,msm8998-qusb2-phy
+      - qcom,sc7180-qusb2-phy
       - qcom,sdm845-qusb2-phy
 
   reg:
@@ -66,7 +67,7 @@ properties:
         It is a 6 bit value that specifies offset to be
         added to PHY refgen RESCODE via IMP_CTRL1 register. It is a PHY
         tuning parameter that may vary for different boards of same SOC.
-        This property is applicable to only QUSB2 v2 PHY (sdm845).
+        This property is applicable to only QUSB2 v2 PHY (sc7180, sdm845).
     $ref: /schemas/types.yaml#/definitions/uint32
 
   qcom,hstx-trim-value:
@@ -75,7 +76,7 @@ properties:
         output current.
         Possible range is - 15mA to 24mA (stepsize of 600 uA).
         See dt-bindings/phy/phy-qcom-qusb2.h for applicable values.
-        This property is applicable to only QUSB2 v2 PHY (sdm845).
+        This property is applicable to only QUSB2 v2 PHY (sc7180, sdm845).
         Default value is 22.2mA for sdm845.
     $ref: /schemas/types.yaml#/definitions/uint32
 
@@ -84,7 +85,7 @@ properties:
         It is a 2 bit value that specifies pre-emphasis level.
         Possible range is 0 to 15% (stepsize of 5%).
         See dt-bindings/phy/phy-qcom-qusb2.h for applicable values.
-        This property is applicable to only QUSB2 v2 PHY (sdm845).
+        This property is applicable to only QUSB2 v2 PHY (sc7180, sdm845).
         Default value is 10% for sdm845.
     $ref: /schemas/types.yaml#/definitions/uint32
 
@@ -94,7 +95,7 @@ properties:
         pre-emphasis (specified using qcom,preemphasis-level) must be in
         effect. Duration could be half-bit of full-bit.
         See dt-bindings/phy/phy-qcom-qusb2.h for applicable values.
-        This property is applicable to only QUSB2 v2 PHY (sdm845).
+        This property is applicable to only QUSB2 v2 PHY (sc7180, sdm845).
         Default value is full-bit width for sdm845.
     $ref: /schemas/types.yaml#/definitions/uint32
 
-- 
QUALCOMM INDIA, on behalf of Qualcomm Innovation Center, Inc. is a member
of Code Aurora Forum, hosted by The Linux Foundation


  parent reply	other threads:[~2019-12-05  4:43 UTC|newest]

Thread overview: 7+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2019-12-05  4:41 [PATCH v2 0/3] Add QUSB2 PHY support for SC7180 Sandeep Maheswaram
2019-12-05  4:41 ` [PATCH v2 1/3] phy: qcom-qusb2: " Sandeep Maheswaram
2019-12-11 22:47   ` Doug Anderson
2019-12-05  4:41 ` [PATCH v2 2/3] dt-bindings: phy: qcom-qusb2: Convert QUSB2 phy bindings to yaml Sandeep Maheswaram
2019-12-18 19:43   ` Doug Anderson
2019-12-05  4:41 ` Sandeep Maheswaram [this message]
2019-12-18 19:09   ` [PATCH v2 3/3] dt-bindings: phy: qcom-qusb2: Add SC7180 QUSB2 phy support Doug Anderson

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=1575520881-31458-4-git-send-email-sanm@codeaurora.org \
    --to=sanm@codeaurora.org \
    --cc=agross@kernel.org \
    --cc=bjorn.andersson@linaro.org \
    --cc=devicetree@vger.kernel.org \
    --cc=kishon@ti.com \
    --cc=linux-arm-msm@vger.kernel.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=mark.rutland@arm.com \
    --cc=mgautam@codeaurora.org \
    --cc=robh+dt@kernel.org \
    --cc=swboyd@chromium.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body. 
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.