From: Sricharan R <sricharan@codeaurora.org> To: sricharan@codeaurora.org, agross@kernel.org, devicetree@vger.kernel.org, linus.walleij@linaro.org, linux-arm-kernel@lists.infradead.org, linux-arm-msm@vger.kernel.org, linux-clk@vger.kernel.org, linux-gpio@vger.kernel.org, linux-kernel@vger.kernel.org, linux-soc@vger.kernel.org, robh+dt@kernel.org, sboyd@kernel.org, sivaprak@codeaurora.org Subject: [PATCH V2 6/7] arm64: dts: Add ipq6018 SoC and CP01 board support Date: Thu, 19 Dec 2019 16:11:48 +0530 [thread overview] Message-ID: <1576752109-24497-7-git-send-email-sricharan@codeaurora.org> (raw) In-Reply-To: <1576752109-24497-1-git-send-email-sricharan@codeaurora.org> Add initial device tree support for the Qualcomm IPQ6018 SoC and CP01 evaluation board. Signed-off-by: Abhishek Sahu <absahu@codeaurora.org> Signed-off-by: Sivaprakash Murugesan <sivaprak@codeaurora.org> Signed-off-by: Sricharan R <sricharan@codeaurora.org> --- [V2] Sorted nodes based on address, name, label. Removed unused clock nodes. Addressed other review comments. arch/arm64/boot/dts/qcom/Makefile | 1 + arch/arm64/boot/dts/qcom/ipq6018-cp01-c1.dts | 41 +++++ arch/arm64/boot/dts/qcom/ipq6018.dtsi | 215 +++++++++++++++++++++++++++ 3 files changed, 257 insertions(+) create mode 100644 arch/arm64/boot/dts/qcom/ipq6018-cp01-c1.dts create mode 100644 arch/arm64/boot/dts/qcom/ipq6018.dtsi diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile index 6498a1e..2b24998 100644 --- a/arch/arm64/boot/dts/qcom/Makefile +++ b/arch/arm64/boot/dts/qcom/Makefile @@ -1,6 +1,7 @@ # SPDX-License-Identifier: GPL-2.0 dtb-$(CONFIG_ARCH_QCOM) += apq8016-sbc.dtb dtb-$(CONFIG_ARCH_QCOM) += apq8096-db820c.dtb +dtb-$(CONFIG_ARCH_QCOM) += ipq6018-cp01-c1.dtb dtb-$(CONFIG_ARCH_QCOM) += ipq8074-hk01.dtb dtb-$(CONFIG_ARCH_QCOM) += msm8916-mtp.dtb dtb-$(CONFIG_ARCH_QCOM) += msm8916-longcheer-l8150.dtb diff --git a/arch/arm64/boot/dts/qcom/ipq6018-cp01-c1.dts b/arch/arm64/boot/dts/qcom/ipq6018-cp01-c1.dts new file mode 100644 index 0000000..82a6024 --- /dev/null +++ b/arch/arm64/boot/dts/qcom/ipq6018-cp01-c1.dts @@ -0,0 +1,41 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * IPQ6018 CP01 board device tree source + * + * Copyright (c) 2019, The Linux Foundation. All rights reserved. + */ + +/dts-v1/; + +#include "ipq6018.dtsi" + +/ { + model = "Qualcomm Technologies, Inc. IPQ6018/AP-CP01-C1"; + compatible = "qcom,ipq6018-cp01", "qcom,ipq6018"; + + aliases { + serial0 = &blsp1_uart3; + }; + + chosen { + stdout-path = "serial0:115200n8"; + bootargs-append = " swiotlb=1"; + }; +}; + +&blsp1_uart3 { + pinctrl-0 = <&uart_pins>; + pinctrl-names = "default"; + status = "ok"; +}; + +&tlmm { + uart_pins: uart_pins { + mux { + pins = "gpio44", "gpio45"; + function = "blsp2_uart"; + drive-strength = <8>; + bias-pull-down; + }; + }; +}; diff --git a/arch/arm64/boot/dts/qcom/ipq6018.dtsi b/arch/arm64/boot/dts/qcom/ipq6018.dtsi new file mode 100644 index 0000000..269287c --- /dev/null +++ b/arch/arm64/boot/dts/qcom/ipq6018.dtsi @@ -0,0 +1,215 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * IPQ6018 SoC device tree source + * + * Copyright (c) 2019, The Linux Foundation. All rights reserved. + */ + +#include <dt-bindings/interrupt-controller/arm-gic.h> +#include <dt-bindings/clock/qcom,gcc-ipq6018.h> + +/ { + #address-cells = <2>; + #size-cells = <2>; + interrupt-parent = <&intc>; + + reserved-memory { + #address-cells = <2>; + #size-cells = <2>; + ranges; + + tz: tz@48500000 { + reg = <0x0 0x48500000 0x0 0x00200000>; + no-map; + }; + }; + + soc: soc { + #address-cells = <1>; + #size-cells = <1>; + ranges = <0 0 0 0xffffffff>; + dma-ranges; + compatible = "simple-bus"; + + tlmm: pinctrl@1000000 { + compatible = "qcom,ipq6018-pinctrl"; + reg = <0x01000000 0x300000>; + interrupts = <GIC_SPI 0xd0 IRQ_TYPE_LEVEL_HIGH>; + gpio-controller; + #gpio-cells = <2>; + gpio-ranges = <&tlmm 0 80>; + interrupt-controller; + #interrupt-cells = <2>; + + uart_pins: uart_pins { + pins = "gpio44", "gpio45"; + function = "blsp2_uart"; + drive-strength = <8>; + bias-pull-down; + }; + }; + + gcc: gcc@1800000 { + compatible = "qcom,gcc-ipq6018"; + reg = <0x01800000 0x80000>; + #clock-cells = <1>; + #reset-cells = <1>; + }; + + blsp1_uart3: serial@78b1000 { + compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm"; + reg = <0x078b1000 0x200>; + interrupts = <GIC_SPI 306 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&gcc GCC_BLSP1_UART3_APPS_CLK>, + <&gcc GCC_BLSP1_AHB_CLK>; + clock-names = "core", "iface"; + status = "disabled"; + }; + + intc: interrupt-controller@b000000 { + compatible = "qcom,msm-qgic2"; + interrupt-controller; + #interrupt-cells = <0x3>; + reg = <0x0b000000 0x1000>, /*GICD*/ + <0x0b002000 0x1000>, /*GICC*/ + <0x0b001000 0x1000>, /*GICH*/ + <0x0b004000 0x1000>; /*GICV*/ + interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH>; + }; + + timer { + compatible = "arm,armv8-timer"; + interrupts = <GIC_PPI 2 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>, + <GIC_PPI 3 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>, + <GIC_PPI 4 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>, + <GIC_PPI 1 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>; + }; + + timer@b120000 { + #address-cells = <1>; + #size-cells = <1>; + ranges; + compatible = "arm,armv7-timer-mem"; + reg = <0x0b120000 0x1000>; + clock-frequency = <19200000>; + + frame@b120000 { + frame-number = <0>; + interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>; + reg = <0x0b121000 0x1000>, + <0x0b122000 0x1000>; + }; + + frame@b123000 { + frame-number = <1>; + interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>; + reg = <0xb123000 0x1000>; + status = "disabled"; + }; + + frame@b124000 { + frame-number = <2>; + interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>; + reg = <0x0b124000 0x1000>; + status = "disabled"; + }; + + frame@b125000 { + frame-number = <3>; + interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>; + reg = <0x0b125000 0x1000>; + status = "disabled"; + }; + + frame@b126000 { + frame-number = <4>; + interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>; + reg = <0x0b126000 0x1000>; + status = "disabled"; + }; + + frame@b127000 { + frame-number = <5>; + interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>; + reg = <0x0b127000 0x1000>; + status = "disabled"; + }; + + frame@b128000 { + frame-number = <6>; + interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>; + reg = <0x0b128000 0x1000>; + status = "disabled"; + }; + }; + + }; + + clocks { + sleep_clk: sleep-clk { + compatible = "fixed-clock"; + clock-frequency = <32000>; + #clock-cells = <0>; + }; + + xo: xo { + compatible = "fixed-clock"; + clock-frequency = <24000000>; + #clock-cells = <0>; + }; + }; + + cpus: cpus { + #address-cells = <1>; + #size-cells = <0>; + + CPU0: cpu@0 { + device_type = "cpu"; + compatible = "arm,cortex-a53"; + reg = <0x0>; + enable-method = "psci"; + next-level-cache = <&L2_0>; + }; + + CPU1: cpu@1 { + device_type = "cpu"; + compatible = "arm,cortex-a53"; + enable-method = "psci"; + reg = <0x1>; + next-level-cache = <&L2_0>; + }; + + CPU2: cpu@2 { + device_type = "cpu"; + compatible = "arm,cortex-a53"; + enable-method = "psci"; + reg = <0x2>; + next-level-cache = <&L2_0>; + }; + + CPU3: cpu@3 { + device_type = "cpu"; + compatible = "arm,cortex-a53"; + enable-method = "psci"; + reg = <0x3>; + next-level-cache = <&L2_0>; + }; + + L2_0: l2-cache { + compatible = "cache"; + cache-level = <0x2>; + }; + }; + + pmuv8: pmu { + compatible = "arm,cortex-a53-pmu"; + interrupts = <GIC_PPI 7 (GIC_CPU_MASK_SIMPLE(4) | + IRQ_TYPE_LEVEL_HIGH)>; + }; + + psci: psci { + compatible = "arm,psci-1.0"; + method = "smc"; + }; +}; -- 1.9.1
WARNING: multiple messages have this Message-ID (diff)
From: Sricharan R <sricharan@codeaurora.org> To: sricharan@codeaurora.org, agross@kernel.org, devicetree@vger.kernel.org, linus.walleij@linaro.org, linux-arm-kernel@lists.infradead.org, linux-arm-msm@vger.kernel.org, linux-clk@vger.kernel.org, linux-gpio@vger.kernel.org, linux-kernel@vger.kernel.org, linux-soc@vger.kernel.org, robh+dt@kernel.org, sboyd@kernel.org, sivaprak@codeaurora.org Subject: [PATCH V2 6/7] arm64: dts: Add ipq6018 SoC and CP01 board support Date: Thu, 19 Dec 2019 16:11:48 +0530 [thread overview] Message-ID: <1576752109-24497-7-git-send-email-sricharan@codeaurora.org> (raw) In-Reply-To: <1576752109-24497-1-git-send-email-sricharan@codeaurora.org> Add initial device tree support for the Qualcomm IPQ6018 SoC and CP01 evaluation board. Signed-off-by: Abhishek Sahu <absahu@codeaurora.org> Signed-off-by: Sivaprakash Murugesan <sivaprak@codeaurora.org> Signed-off-by: Sricharan R <sricharan@codeaurora.org> --- [V2] Sorted nodes based on address, name, label. Removed unused clock nodes. Addressed other review comments. arch/arm64/boot/dts/qcom/Makefile | 1 + arch/arm64/boot/dts/qcom/ipq6018-cp01-c1.dts | 41 +++++ arch/arm64/boot/dts/qcom/ipq6018.dtsi | 215 +++++++++++++++++++++++++++ 3 files changed, 257 insertions(+) create mode 100644 arch/arm64/boot/dts/qcom/ipq6018-cp01-c1.dts create mode 100644 arch/arm64/boot/dts/qcom/ipq6018.dtsi diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile index 6498a1e..2b24998 100644 --- a/arch/arm64/boot/dts/qcom/Makefile +++ b/arch/arm64/boot/dts/qcom/Makefile @@ -1,6 +1,7 @@ # SPDX-License-Identifier: GPL-2.0 dtb-$(CONFIG_ARCH_QCOM) += apq8016-sbc.dtb dtb-$(CONFIG_ARCH_QCOM) += apq8096-db820c.dtb +dtb-$(CONFIG_ARCH_QCOM) += ipq6018-cp01-c1.dtb dtb-$(CONFIG_ARCH_QCOM) += ipq8074-hk01.dtb dtb-$(CONFIG_ARCH_QCOM) += msm8916-mtp.dtb dtb-$(CONFIG_ARCH_QCOM) += msm8916-longcheer-l8150.dtb diff --git a/arch/arm64/boot/dts/qcom/ipq6018-cp01-c1.dts b/arch/arm64/boot/dts/qcom/ipq6018-cp01-c1.dts new file mode 100644 index 0000000..82a6024 --- /dev/null +++ b/arch/arm64/boot/dts/qcom/ipq6018-cp01-c1.dts @@ -0,0 +1,41 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * IPQ6018 CP01 board device tree source + * + * Copyright (c) 2019, The Linux Foundation. All rights reserved. + */ + +/dts-v1/; + +#include "ipq6018.dtsi" + +/ { + model = "Qualcomm Technologies, Inc. IPQ6018/AP-CP01-C1"; + compatible = "qcom,ipq6018-cp01", "qcom,ipq6018"; + + aliases { + serial0 = &blsp1_uart3; + }; + + chosen { + stdout-path = "serial0:115200n8"; + bootargs-append = " swiotlb=1"; + }; +}; + +&blsp1_uart3 { + pinctrl-0 = <&uart_pins>; + pinctrl-names = "default"; + status = "ok"; +}; + +&tlmm { + uart_pins: uart_pins { + mux { + pins = "gpio44", "gpio45"; + function = "blsp2_uart"; + drive-strength = <8>; + bias-pull-down; + }; + }; +}; diff --git a/arch/arm64/boot/dts/qcom/ipq6018.dtsi b/arch/arm64/boot/dts/qcom/ipq6018.dtsi new file mode 100644 index 0000000..269287c --- /dev/null +++ b/arch/arm64/boot/dts/qcom/ipq6018.dtsi @@ -0,0 +1,215 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * IPQ6018 SoC device tree source + * + * Copyright (c) 2019, The Linux Foundation. All rights reserved. + */ + +#include <dt-bindings/interrupt-controller/arm-gic.h> +#include <dt-bindings/clock/qcom,gcc-ipq6018.h> + +/ { + #address-cells = <2>; + #size-cells = <2>; + interrupt-parent = <&intc>; + + reserved-memory { + #address-cells = <2>; + #size-cells = <2>; + ranges; + + tz: tz@48500000 { + reg = <0x0 0x48500000 0x0 0x00200000>; + no-map; + }; + }; + + soc: soc { + #address-cells = <1>; + #size-cells = <1>; + ranges = <0 0 0 0xffffffff>; + dma-ranges; + compatible = "simple-bus"; + + tlmm: pinctrl@1000000 { + compatible = "qcom,ipq6018-pinctrl"; + reg = <0x01000000 0x300000>; + interrupts = <GIC_SPI 0xd0 IRQ_TYPE_LEVEL_HIGH>; + gpio-controller; + #gpio-cells = <2>; + gpio-ranges = <&tlmm 0 80>; + interrupt-controller; + #interrupt-cells = <2>; + + uart_pins: uart_pins { + pins = "gpio44", "gpio45"; + function = "blsp2_uart"; + drive-strength = <8>; + bias-pull-down; + }; + }; + + gcc: gcc@1800000 { + compatible = "qcom,gcc-ipq6018"; + reg = <0x01800000 0x80000>; + #clock-cells = <1>; + #reset-cells = <1>; + }; + + blsp1_uart3: serial@78b1000 { + compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm"; + reg = <0x078b1000 0x200>; + interrupts = <GIC_SPI 306 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&gcc GCC_BLSP1_UART3_APPS_CLK>, + <&gcc GCC_BLSP1_AHB_CLK>; + clock-names = "core", "iface"; + status = "disabled"; + }; + + intc: interrupt-controller@b000000 { + compatible = "qcom,msm-qgic2"; + interrupt-controller; + #interrupt-cells = <0x3>; + reg = <0x0b000000 0x1000>, /*GICD*/ + <0x0b002000 0x1000>, /*GICC*/ + <0x0b001000 0x1000>, /*GICH*/ + <0x0b004000 0x1000>; /*GICV*/ + interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH>; + }; + + timer { + compatible = "arm,armv8-timer"; + interrupts = <GIC_PPI 2 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>, + <GIC_PPI 3 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>, + <GIC_PPI 4 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>, + <GIC_PPI 1 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>; + }; + + timer@b120000 { + #address-cells = <1>; + #size-cells = <1>; + ranges; + compatible = "arm,armv7-timer-mem"; + reg = <0x0b120000 0x1000>; + clock-frequency = <19200000>; + + frame@b120000 { + frame-number = <0>; + interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>; + reg = <0x0b121000 0x1000>, + <0x0b122000 0x1000>; + }; + + frame@b123000 { + frame-number = <1>; + interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>; + reg = <0xb123000 0x1000>; + status = "disabled"; + }; + + frame@b124000 { + frame-number = <2>; + interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>; + reg = <0x0b124000 0x1000>; + status = "disabled"; + }; + + frame@b125000 { + frame-number = <3>; + interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>; + reg = <0x0b125000 0x1000>; + status = "disabled"; + }; + + frame@b126000 { + frame-number = <4>; + interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>; + reg = <0x0b126000 0x1000>; + status = "disabled"; + }; + + frame@b127000 { + frame-number = <5>; + interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>; + reg = <0x0b127000 0x1000>; + status = "disabled"; + }; + + frame@b128000 { + frame-number = <6>; + interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>; + reg = <0x0b128000 0x1000>; + status = "disabled"; + }; + }; + + }; + + clocks { + sleep_clk: sleep-clk { + compatible = "fixed-clock"; + clock-frequency = <32000>; + #clock-cells = <0>; + }; + + xo: xo { + compatible = "fixed-clock"; + clock-frequency = <24000000>; + #clock-cells = <0>; + }; + }; + + cpus: cpus { + #address-cells = <1>; + #size-cells = <0>; + + CPU0: cpu@0 { + device_type = "cpu"; + compatible = "arm,cortex-a53"; + reg = <0x0>; + enable-method = "psci"; + next-level-cache = <&L2_0>; + }; + + CPU1: cpu@1 { + device_type = "cpu"; + compatible = "arm,cortex-a53"; + enable-method = "psci"; + reg = <0x1>; + next-level-cache = <&L2_0>; + }; + + CPU2: cpu@2 { + device_type = "cpu"; + compatible = "arm,cortex-a53"; + enable-method = "psci"; + reg = <0x2>; + next-level-cache = <&L2_0>; + }; + + CPU3: cpu@3 { + device_type = "cpu"; + compatible = "arm,cortex-a53"; + enable-method = "psci"; + reg = <0x3>; + next-level-cache = <&L2_0>; + }; + + L2_0: l2-cache { + compatible = "cache"; + cache-level = <0x2>; + }; + }; + + pmuv8: pmu { + compatible = "arm,cortex-a53-pmu"; + interrupts = <GIC_PPI 7 (GIC_CPU_MASK_SIMPLE(4) | + IRQ_TYPE_LEVEL_HIGH)>; + }; + + psci: psci { + compatible = "arm,psci-1.0"; + method = "smc"; + }; +}; -- 1.9.1 _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
next prev parent reply other threads:[~2019-12-19 10:43 UTC|newest] Thread overview: 37+ messages / expand[flat|nested] mbox.gz Atom feed top 2019-12-19 10:41 [PATCH V2 0/7] Add minimal boot support for IPQ6018 Sricharan R 2019-12-19 10:41 ` Sricharan R 2019-12-19 10:41 ` [PATCH V2 1/7] dt-bindings: pinctrl: qcom: Add ipq6018 pinctrl bindings Sricharan R 2019-12-19 10:41 ` Sricharan R 2019-12-29 3:41 ` Bjorn Andersson 2019-12-29 3:41 ` Bjorn Andersson 2019-12-30 9:12 ` Sricharan R 2019-12-30 9:12 ` Sricharan R 2019-12-19 10:41 ` [PATCH V2 2/7] pinctrl: qcom: Add ipq6018 pinctrl driver Sricharan R 2019-12-19 10:41 ` Sricharan R 2019-12-29 3:35 ` Bjorn Andersson 2019-12-29 3:35 ` Bjorn Andersson 2019-12-30 9:10 ` Sricharan R 2019-12-30 9:10 ` Sricharan R 2019-12-19 10:41 ` [PATCH V2 3/7] dt-bindings: qcom: Add ipq6018 bindings Sricharan R 2019-12-19 10:41 ` Sricharan R 2019-12-19 10:41 ` [PATCH V2 4/7] clk: qcom: Add DT bindings for ipq6018 gcc clock controller Sricharan R 2019-12-19 10:41 ` Sricharan R 2019-12-19 18:24 ` Rob Herring 2019-12-19 18:24 ` Rob Herring 2019-12-19 10:41 ` [PATCH V2 5/7] clk: qcom: Add ipq6018 Global Clock Controller support Sricharan R 2019-12-27 1:33 ` Stephen Boyd 2019-12-27 1:33 ` Stephen Boyd 2019-12-30 9:06 ` Sricharan R 2019-12-30 9:06 ` Sricharan R 2019-12-19 10:41 ` Sricharan R [this message] 2019-12-19 10:41 ` [PATCH V2 6/7] arm64: dts: Add ipq6018 SoC and CP01 board support Sricharan R 2019-12-29 3:29 ` Bjorn Andersson 2019-12-29 3:29 ` Bjorn Andersson 2019-12-30 9:10 ` Sricharan R 2019-12-30 9:10 ` Sricharan R 2019-12-19 10:41 ` [PATCH V2 7/7] arm64: defconfig: Enable qcom ipq6018 clock and pinctrl Sricharan R 2019-12-19 10:41 ` Sricharan R 2019-12-27 1:33 ` [PATCH V2 0/7] Add minimal boot support for IPQ6018 Stephen Boyd 2019-12-27 1:33 ` Stephen Boyd 2019-12-30 9:07 ` Sricharan R 2019-12-30 9:07 ` Sricharan R
Reply instructions: You may reply publicly to this message via plain-text email using any one of the following methods: * Save the following mbox file, import it into your mail client, and reply-to-all from there: mbox Avoid top-posting and favor interleaved quoting: https://en.wikipedia.org/wiki/Posting_style#Interleaved_style * Reply using the --to, --cc, and --in-reply-to switches of git-send-email(1): git send-email \ --in-reply-to=1576752109-24497-7-git-send-email-sricharan@codeaurora.org \ --to=sricharan@codeaurora.org \ --cc=agross@kernel.org \ --cc=devicetree@vger.kernel.org \ --cc=linus.walleij@linaro.org \ --cc=linux-arm-kernel@lists.infradead.org \ --cc=linux-arm-msm@vger.kernel.org \ --cc=linux-clk@vger.kernel.org \ --cc=linux-gpio@vger.kernel.org \ --cc=linux-kernel@vger.kernel.org \ --cc=linux-soc@vger.kernel.org \ --cc=robh+dt@kernel.org \ --cc=sboyd@kernel.org \ --cc=sivaprak@codeaurora.org \ /path/to/YOUR_REPLY https://kernel.org/pub/software/scm/git/docs/git-send-email.html * If your mail client supports setting the In-Reply-To header via mailto: links, try the mailto: linkBe sure your reply has a Subject: header at the top and a blank line before the message body.
This is an external index of several public inboxes, see mirroring instructions on how to clone and mirror all data and code used by this external index.