All of lore.kernel.org
 help / color / mirror / Atom feed
From: Rakesh Pillai <pillair@codeaurora.org>
To: ath10k@lists.infradead.org
Cc: linux-wireless@vger.kernel.org, linux-kernel@vger.kernel.org,
	Rakesh Pillai <pillair@codeaurora.org>
Subject: [PATCH v2 2/2] ath10k: Skip wait for delete response if firmware is down
Date: Sat, 27 Jun 2020 00:23:53 +0530	[thread overview]
Message-ID: <1593197633-9014-3-git-send-email-pillair@codeaurora.org> (raw)
In-Reply-To: <1593197633-9014-1-git-send-email-pillair@codeaurora.org>

Currently the driver waits for response from the
firmware for all the delete cmds, eg: vdev_delete,
peer delete. If the firmware is down, these wait
will always timeout and return an error.

Also during subsytems recovery, any attempt to
send a WMI cmd to the FW will return the -ESHUTDOWN
status, which when returned to mac80211, can cause
unnecessary warnings to be printed on to the console,
as shown below

[ 2559.529565] Call trace:
[ 2559.532214]  __sta_info_destroy_part2+0x160/0x168 [mac80211]
[ 2559.538157]  __sta_info_flush+0x124/0x180 [mac80211]
[ 2559.543402]  ieee80211_set_disassoc+0x130/0x2c0 [mac80211]
[ 2559.549172]  ieee80211_mgd_deauth+0x238/0x25c [mac80211]
[ 2559.554764]  ieee80211_deauth+0x24/0x30 [mac80211]
[ 2559.559860]  cfg80211_mlme_deauth+0x258/0x2b0 [cfg80211]
[ 2559.565446]  nl80211_deauthenticate+0xe4/0x110 [cfg80211]
[ 2559.571064]  genl_rcv_msg+0x3a0/0x440
[ 2559.574888]  netlink_rcv_skb+0xb4/0x11c
[ 2559.578877]  genl_rcv+0x34/0x48
[ 2559.582162]  netlink_unicast+0x14c/0x1e4
[ 2559.586235]  netlink_sendmsg+0x2f0/0x360
[ 2559.590317]  sock_sendmsg+0x44/0x5c
[ 2559.593951]  ____sys_sendmsg+0x1c8/0x290
[ 2559.598029]  ___sys_sendmsg+0xa8/0xfc
[ 2559.601840]  __sys_sendmsg+0x8c/0xd0
[ 2559.605572]  __arm64_compat_sys_sendmsg+0x2c/0x38
[ 2559.610468]  el0_svc_common+0xa8/0x160
[ 2559.614372]  el0_svc_compat_handler+0x2c/0x38
[ 2559.618905]  el0_svc_compat+0x8/0x10

Skip the wait for delete response from the
firmware if the firmware is down. Also return
success to the mac80211 calls when the peer delete
cmd fails with return status -ESHUTDOWN.

Tested-on: WCN3990 hw1.0 SNOC WLAN.HL.3.1-01040-QCAHLSWMTPLZ-1

Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
---
 drivers/net/wireless/ath/ath10k/mac.c | 18 ++++++++++++++----
 1 file changed, 14 insertions(+), 4 deletions(-)

diff --git a/drivers/net/wireless/ath/ath10k/mac.c b/drivers/net/wireless/ath/ath10k/mac.c
index dc7befc..6882fcc 100644
--- a/drivers/net/wireless/ath/ath10k/mac.c
+++ b/drivers/net/wireless/ath/ath10k/mac.c
@@ -701,7 +701,8 @@ static void ath10k_wait_for_peer_delete_done(struct ath10k *ar, u32 vdev_id,
 	unsigned long time_left;
 	int ret;
 
-	if (test_bit(WMI_SERVICE_SYNC_DELETE_CMDS, ar->wmi.svc_map)) {
+	if (test_bit(WMI_SERVICE_SYNC_DELETE_CMDS, ar->wmi.svc_map) &&
+	    !test_bit(ATH10K_FLAG_CRASH_FLUSH, &ar->dev_flags)) {
 		ret = ath10k_wait_for_peer_deleted(ar, vdev_id, addr);
 		if (ret) {
 			ath10k_warn(ar, "failed wait for peer deleted");
@@ -841,7 +842,8 @@ static int ath10k_peer_delete(struct ath10k *ar, u32 vdev_id, const u8 *addr)
 	if (ret)
 		return ret;
 
-	if (test_bit(WMI_SERVICE_SYNC_DELETE_CMDS, ar->wmi.svc_map)) {
+	if (test_bit(WMI_SERVICE_SYNC_DELETE_CMDS, ar->wmi.svc_map) &&
+	    !test_bit(ATH10K_FLAG_CRASH_FLUSH, &ar->dev_flags)) {
 		unsigned long time_left;
 
 		time_left = wait_for_completion_timeout
@@ -5673,7 +5675,8 @@ static void ath10k_remove_interface(struct ieee80211_hw *hw,
 		ath10k_warn(ar, "failed to delete WMI vdev %i: %d\n",
 			    arvif->vdev_id, ret);
 
-	if (test_bit(WMI_SERVICE_SYNC_DELETE_CMDS, ar->wmi.svc_map)) {
+	if (test_bit(WMI_SERVICE_SYNC_DELETE_CMDS, ar->wmi.svc_map) &&
+	    !test_bit(ATH10K_FLAG_CRASH_FLUSH, &ar->dev_flags)) {
 		time_left = wait_for_completion_timeout(&ar->vdev_delete_done,
 							ATH10K_VDEV_DELETE_TIMEOUT_HZ);
 		if (time_left == 0) {
@@ -6110,6 +6113,11 @@ static int ath10k_hw_scan(struct ieee80211_hw *hw,
 		goto exit;
 	}
 
+	if (test_bit(ATH10K_FLAG_CRASH_FLUSH, &ar->dev_flags)) {
+		ret = -ESHUTDOWN;
+		goto exit;
+	}
+
 	spin_lock_bh(&ar->data_lock);
 	switch (ar->scan.state) {
 	case ATH10K_SCAN_IDLE:
@@ -6758,7 +6766,9 @@ static int ath10k_sta_state(struct ieee80211_hw *hw,
 		}
 
 		ret = ath10k_peer_delete(ar, arvif->vdev_id, sta->addr);
-		if (ret)
+		if (ret == -ESHUTDOWN)
+			ret = 0;
+		else if (ret)
 			ath10k_warn(ar, "failed to delete peer %pM for vdev %d: %i\n",
 				    sta->addr, arvif->vdev_id, ret);
 
-- 
2.7.4


WARNING: multiple messages have this Message-ID (diff)
From: Rakesh Pillai <pillair@codeaurora.org>
To: ath10k@lists.infradead.org
Cc: Rakesh Pillai <pillair@codeaurora.org>,
	linux-wireless@vger.kernel.org, linux-kernel@vger.kernel.org
Subject: [PATCH v2 2/2] ath10k: Skip wait for delete response if firmware is down
Date: Sat, 27 Jun 2020 00:23:53 +0530	[thread overview]
Message-ID: <1593197633-9014-3-git-send-email-pillair@codeaurora.org> (raw)
In-Reply-To: <1593197633-9014-1-git-send-email-pillair@codeaurora.org>

Currently the driver waits for response from the
firmware for all the delete cmds, eg: vdev_delete,
peer delete. If the firmware is down, these wait
will always timeout and return an error.

Also during subsytems recovery, any attempt to
send a WMI cmd to the FW will return the -ESHUTDOWN
status, which when returned to mac80211, can cause
unnecessary warnings to be printed on to the console,
as shown below

[ 2559.529565] Call trace:
[ 2559.532214]  __sta_info_destroy_part2+0x160/0x168 [mac80211]
[ 2559.538157]  __sta_info_flush+0x124/0x180 [mac80211]
[ 2559.543402]  ieee80211_set_disassoc+0x130/0x2c0 [mac80211]
[ 2559.549172]  ieee80211_mgd_deauth+0x238/0x25c [mac80211]
[ 2559.554764]  ieee80211_deauth+0x24/0x30 [mac80211]
[ 2559.559860]  cfg80211_mlme_deauth+0x258/0x2b0 [cfg80211]
[ 2559.565446]  nl80211_deauthenticate+0xe4/0x110 [cfg80211]
[ 2559.571064]  genl_rcv_msg+0x3a0/0x440
[ 2559.574888]  netlink_rcv_skb+0xb4/0x11c
[ 2559.578877]  genl_rcv+0x34/0x48
[ 2559.582162]  netlink_unicast+0x14c/0x1e4
[ 2559.586235]  netlink_sendmsg+0x2f0/0x360
[ 2559.590317]  sock_sendmsg+0x44/0x5c
[ 2559.593951]  ____sys_sendmsg+0x1c8/0x290
[ 2559.598029]  ___sys_sendmsg+0xa8/0xfc
[ 2559.601840]  __sys_sendmsg+0x8c/0xd0
[ 2559.605572]  __arm64_compat_sys_sendmsg+0x2c/0x38
[ 2559.610468]  el0_svc_common+0xa8/0x160
[ 2559.614372]  el0_svc_compat_handler+0x2c/0x38
[ 2559.618905]  el0_svc_compat+0x8/0x10

Skip the wait for delete response from the
firmware if the firmware is down. Also return
success to the mac80211 calls when the peer delete
cmd fails with return status -ESHUTDOWN.

Tested-on: WCN3990 hw1.0 SNOC WLAN.HL.3.1-01040-QCAHLSWMTPLZ-1

Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
---
 drivers/net/wireless/ath/ath10k/mac.c | 18 ++++++++++++++----
 1 file changed, 14 insertions(+), 4 deletions(-)

diff --git a/drivers/net/wireless/ath/ath10k/mac.c b/drivers/net/wireless/ath/ath10k/mac.c
index dc7befc..6882fcc 100644
--- a/drivers/net/wireless/ath/ath10k/mac.c
+++ b/drivers/net/wireless/ath/ath10k/mac.c
@@ -701,7 +701,8 @@ static void ath10k_wait_for_peer_delete_done(struct ath10k *ar, u32 vdev_id,
 	unsigned long time_left;
 	int ret;
 
-	if (test_bit(WMI_SERVICE_SYNC_DELETE_CMDS, ar->wmi.svc_map)) {
+	if (test_bit(WMI_SERVICE_SYNC_DELETE_CMDS, ar->wmi.svc_map) &&
+	    !test_bit(ATH10K_FLAG_CRASH_FLUSH, &ar->dev_flags)) {
 		ret = ath10k_wait_for_peer_deleted(ar, vdev_id, addr);
 		if (ret) {
 			ath10k_warn(ar, "failed wait for peer deleted");
@@ -841,7 +842,8 @@ static int ath10k_peer_delete(struct ath10k *ar, u32 vdev_id, const u8 *addr)
 	if (ret)
 		return ret;
 
-	if (test_bit(WMI_SERVICE_SYNC_DELETE_CMDS, ar->wmi.svc_map)) {
+	if (test_bit(WMI_SERVICE_SYNC_DELETE_CMDS, ar->wmi.svc_map) &&
+	    !test_bit(ATH10K_FLAG_CRASH_FLUSH, &ar->dev_flags)) {
 		unsigned long time_left;
 
 		time_left = wait_for_completion_timeout
@@ -5673,7 +5675,8 @@ static void ath10k_remove_interface(struct ieee80211_hw *hw,
 		ath10k_warn(ar, "failed to delete WMI vdev %i: %d\n",
 			    arvif->vdev_id, ret);
 
-	if (test_bit(WMI_SERVICE_SYNC_DELETE_CMDS, ar->wmi.svc_map)) {
+	if (test_bit(WMI_SERVICE_SYNC_DELETE_CMDS, ar->wmi.svc_map) &&
+	    !test_bit(ATH10K_FLAG_CRASH_FLUSH, &ar->dev_flags)) {
 		time_left = wait_for_completion_timeout(&ar->vdev_delete_done,
 							ATH10K_VDEV_DELETE_TIMEOUT_HZ);
 		if (time_left == 0) {
@@ -6110,6 +6113,11 @@ static int ath10k_hw_scan(struct ieee80211_hw *hw,
 		goto exit;
 	}
 
+	if (test_bit(ATH10K_FLAG_CRASH_FLUSH, &ar->dev_flags)) {
+		ret = -ESHUTDOWN;
+		goto exit;
+	}
+
 	spin_lock_bh(&ar->data_lock);
 	switch (ar->scan.state) {
 	case ATH10K_SCAN_IDLE:
@@ -6758,7 +6766,9 @@ static int ath10k_sta_state(struct ieee80211_hw *hw,
 		}
 
 		ret = ath10k_peer_delete(ar, arvif->vdev_id, sta->addr);
-		if (ret)
+		if (ret == -ESHUTDOWN)
+			ret = 0;
+		else if (ret)
 			ath10k_warn(ar, "failed to delete peer %pM for vdev %d: %i\n",
 				    sta->addr, arvif->vdev_id, ret);
 
-- 
2.7.4


_______________________________________________
ath10k mailing list
ath10k@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/ath10k

  parent reply	other threads:[~2020-06-26 18:54 UTC|newest]

Thread overview: 16+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2020-06-26 18:53 [PATCH v2 0/2] ath10k: Fixes during subsystem recovery Rakesh Pillai
2020-06-26 18:53 ` Rakesh Pillai
2020-06-26 18:53 ` [PATCH v2 1/2] ath10k: Pause the tx queues when firmware is down Rakesh Pillai
2020-06-26 18:53   ` Rakesh Pillai
2020-06-26 18:53 ` Rakesh Pillai [this message]
2020-06-26 18:53   ` [PATCH v2 2/2] ath10k: Skip wait for delete response if " Rakesh Pillai
2020-09-15  7:47 ` [PATCH v2 0/2] ath10k: Fixes during subsystem recovery Rakesh Pillai
2020-09-15  7:47   ` Rakesh Pillai
2020-09-15 14:28   ` Kalle Valo
2020-09-15 14:28     ` Kalle Valo
2020-12-21 18:37 ` Kalle Valo
2020-12-21 18:37   ` Kalle Valo
2021-01-15 13:25   ` Rakesh Pillai
2021-01-15 13:25     ` Rakesh Pillai
2021-02-26 14:40   ` Rakesh Pillai
2021-02-26 14:40     ` Rakesh Pillai

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=1593197633-9014-3-git-send-email-pillair@codeaurora.org \
    --to=pillair@codeaurora.org \
    --cc=ath10k@lists.infradead.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=linux-wireless@vger.kernel.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.