From: Richard Zhu <hongxing.zhu@nxp.com> To: shawnguo@kernel.org Cc: l.stach@pengutronix.de, linux-imx@nxp.com, linux-arm-kernel@lists.infradead.org, linux-kernel@vger.kernel.org, Richard Zhu <hongxing.zhu@nxp.com> Subject: [PATCH] arm64: dts: imx8mq-evk: add one regulator used to power up pcie phy Date: Wed, 14 Apr 2021 10:26:14 +0800 [thread overview] Message-ID: <1618367174-30968-2-git-send-email-hongxing.zhu@nxp.com> (raw) In-Reply-To: <1618367174-30968-1-git-send-email-hongxing.zhu@nxp.com> Both 1.8v and 3.3v power supplies can be used by i.MX8MQ PCIe PHY. In default, the PCIE_VPH voltage is suggested to be 1.8v refer to data sheet. When PCIE_VPH is supplied by 3.3v in the HW schematic design, the VREG_BYPASS bits of GPR registers should be cleared from default value 1b'1 to 1b'0. Thus, the internal 3v3 to 1v8 translator would be turned on. Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com> Reviewed-by: Lucas Stach <l.stach@pengutronix.de> --- arch/arm64/boot/dts/freescale/imx8mq-evk.dts | 1 + 1 file changed, 1 insertion(+) diff --git a/arch/arm64/boot/dts/freescale/imx8mq-evk.dts b/arch/arm64/boot/dts/freescale/imx8mq-evk.dts index 85b045253a0e..4d2035e3dd7c 100644 --- a/arch/arm64/boot/dts/freescale/imx8mq-evk.dts +++ b/arch/arm64/boot/dts/freescale/imx8mq-evk.dts @@ -318,6 +318,7 @@ <&clk IMX8MQ_CLK_PCIE1_PHY>, <&pcie0_refclk>; clock-names = "pcie", "pcie_aux", "pcie_phy", "pcie_bus"; + vph-supply = <&vgen5_reg>; status = "okay"; }; -- 2.17.1
WARNING: multiple messages have this Message-ID (diff)
From: Richard Zhu <hongxing.zhu@nxp.com> To: shawnguo@kernel.org Cc: l.stach@pengutronix.de, linux-imx@nxp.com, linux-arm-kernel@lists.infradead.org, linux-kernel@vger.kernel.org, Richard Zhu <hongxing.zhu@nxp.com> Subject: [PATCH] arm64: dts: imx8mq-evk: add one regulator used to power up pcie phy Date: Wed, 14 Apr 2021 10:26:14 +0800 [thread overview] Message-ID: <1618367174-30968-2-git-send-email-hongxing.zhu@nxp.com> (raw) In-Reply-To: <1618367174-30968-1-git-send-email-hongxing.zhu@nxp.com> Both 1.8v and 3.3v power supplies can be used by i.MX8MQ PCIe PHY. In default, the PCIE_VPH voltage is suggested to be 1.8v refer to data sheet. When PCIE_VPH is supplied by 3.3v in the HW schematic design, the VREG_BYPASS bits of GPR registers should be cleared from default value 1b'1 to 1b'0. Thus, the internal 3v3 to 1v8 translator would be turned on. Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com> Reviewed-by: Lucas Stach <l.stach@pengutronix.de> --- arch/arm64/boot/dts/freescale/imx8mq-evk.dts | 1 + 1 file changed, 1 insertion(+) diff --git a/arch/arm64/boot/dts/freescale/imx8mq-evk.dts b/arch/arm64/boot/dts/freescale/imx8mq-evk.dts index 85b045253a0e..4d2035e3dd7c 100644 --- a/arch/arm64/boot/dts/freescale/imx8mq-evk.dts +++ b/arch/arm64/boot/dts/freescale/imx8mq-evk.dts @@ -318,6 +318,7 @@ <&clk IMX8MQ_CLK_PCIE1_PHY>, <&pcie0_refclk>; clock-names = "pcie", "pcie_aux", "pcie_phy", "pcie_bus"; + vph-supply = <&vgen5_reg>; status = "okay"; }; -- 2.17.1 _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
next prev parent reply other threads:[~2021-04-14 2:41 UTC|newest] Thread overview: 12+ messages / expand[flat|nested] mbox.gz Atom feed top 2021-04-14 2:26 [PATCH] arm64: dts: imx8mq-evk: add one regulator used to power up Richard Zhu 2021-04-14 2:26 ` Richard Zhu 2021-04-14 2:26 ` Richard Zhu [this message] 2021-04-14 2:26 ` [PATCH] arm64: dts: imx8mq-evk: add one regulator used to power up pcie phy Richard Zhu 2021-04-14 3:02 ` Richard Zhu 2021-04-14 3:02 ` Richard Zhu 2021-05-13 7:14 ` Shawn Guo 2021-05-13 7:14 ` Shawn Guo -- strict thread matches above, loose matches on Subject: below -- 2021-03-29 8:06 Richard Zhu 2021-03-29 8:06 ` Richard Zhu 2021-04-26 1:24 ` Shawn Guo 2021-04-26 1:24 ` Shawn Guo
Reply instructions: You may reply publicly to this message via plain-text email using any one of the following methods: * Save the following mbox file, import it into your mail client, and reply-to-all from there: mbox Avoid top-posting and favor interleaved quoting: https://en.wikipedia.org/wiki/Posting_style#Interleaved_style * Reply using the --to, --cc, and --in-reply-to switches of git-send-email(1): git send-email \ --in-reply-to=1618367174-30968-2-git-send-email-hongxing.zhu@nxp.com \ --to=hongxing.zhu@nxp.com \ --cc=l.stach@pengutronix.de \ --cc=linux-arm-kernel@lists.infradead.org \ --cc=linux-imx@nxp.com \ --cc=linux-kernel@vger.kernel.org \ --cc=shawnguo@kernel.org \ /path/to/YOUR_REPLY https://kernel.org/pub/software/scm/git/docs/git-send-email.html * If your mail client supports setting the In-Reply-To header via mailto: links, try the mailto: linkBe sure your reply has a Subject: header at the top and a blank line before the message body.
This is an external index of several public inboxes, see mirroring instructions on how to clone and mirror all data and code used by this external index.