All of lore.kernel.org
 help / color / mirror / Atom feed
From: Shaik Sajida Bhanu <sbhanu@codeaurora.org>
To: adrian.hunter@intel.com, ulf.hansson@linaro.org
Cc: asutoshd@codeaurora.org, stummala@codeaurora.org,
	vbadigan@codeaurora.org, rampraka@codeaurora.org,
	sayalil@codeaurora.org, sartgarg@codeaurora.org,
	rnayak@codeaurora.org, cang@codeaurora.org,
	pragalla@codeaurora.org, nitirawa@codeaurora.org,
	linux-mmc@vger.kernel.org, linux-kernel@vger.kernel.org,
	linux-arm-msm@vger.kernel.org, agross@kernel.org,
	bjorn.andersson@linaro.org, robh+dt@kernel.org,
	Shaik Sajida Bhanu <sbhanu@codeaurora.org>
Subject: [PATCH V3] mmc: sdhci-msm: Update the software timeout value for sdhc
Date: Mon,  5 Jul 2021 21:20:53 +0530	[thread overview]
Message-ID: <1625500253-12815-1-git-send-email-sbhanu@codeaurora.org> (raw)

Whenever SDHC run at clock rate 50MHZ or below, the hardware data
timeout value will be 21.47secs, which is approx. 22secs and we have
a current software timeout value as 10secs. We have to set software
timeout value more than the hardware data timeout value to avioid seeing
the below register dumps.

[  332.953670] mmc2: Timeout waiting for hardware interrupt.
[  332.959608] mmc2: sdhci: ============ SDHCI REGISTER DUMP ===========
[  332.966450] mmc2: sdhci: Sys addr:  0x00000000 | Version:  0x00007202
[  332.973256] mmc2: sdhci: Blk size:  0x00000200 | Blk cnt:  0x00000001
[  332.980054] mmc2: sdhci: Argument:  0x00000000 | Trn mode: 0x00000027
[  332.986864] mmc2: sdhci: Present:   0x01f801f6 | Host ctl: 0x0000001f
[  332.993671] mmc2: sdhci: Power:     0x00000001 | Blk gap:  0x00000000
[  333.000583] mmc2: sdhci: Wake-up:   0x00000000 | Clock:    0x00000007
[  333.007386] mmc2: sdhci: Timeout:   0x0000000e | Int stat: 0x00000000
[  333.014182] mmc2: sdhci: Int enab:  0x03ff100b | Sig enab: 0x03ff100b
[  333.020976] mmc2: sdhci: ACmd stat: 0x00000000 | Slot int: 0x00000000
[  333.027771] mmc2: sdhci: Caps:      0x322dc8b2 | Caps_1:   0x0000808f
[  333.034561] mmc2: sdhci: Cmd:       0x0000183a | Max curr: 0x00000000
[  333.041359] mmc2: sdhci: Resp[0]:   0x00000900 | Resp[1]:  0x00000000
[  333.048157] mmc2: sdhci: Resp[2]:   0x00000000 | Resp[3]:  0x00000000
[  333.054945] mmc2: sdhci: Host ctl2: 0x00000000
[  333.059657] mmc2: sdhci: ADMA Err:  0x00000000 | ADMA Ptr:
0x0000000ffffff218
[  333.067178] mmc2: sdhci_msm: ----------- VENDOR REGISTER DUMP
-----------
[  333.074343] mmc2: sdhci_msm: DLL sts: 0x00000000 | DLL cfg:
0x6000642c | DLL cfg2: 0x0020a000
[  333.083417] mmc2: sdhci_msm: DLL cfg3: 0x00000000 | DLL usr ctl:
0x00000000 | DDR cfg: 0x80040873
[  333.092850] mmc2: sdhci_msm: Vndr func: 0x00008a9c | Vndr func2 :
0xf88218a8 Vndr func3: 0x02626040
[  333.102371] mmc2: sdhci: ============================================

So, set software timeout value more than hardware timeout value.

Signed-off-by: Shaik Sajida Bhanu <sbhanu@codeaurora.org>
---

Changes since V2:
	- Updated 22 with 22LL to avoid compiler warning as suggested by
	  Adrian Hunter.
	- Added a check to update software data timeout value if its value is
	  less than the calculated hardware data timeout value as suggested
	  by Veerabhadrarao Badiganti.

Changes since V1:
	- Moved software data timeout update part to qcom specific file
	  as suggested by Veerabhadrarao Badiganti.
---
 drivers/mmc/host/sdhci-msm.c | 18 ++++++++++++++++++
 1 file changed, 18 insertions(+)

diff --git a/drivers/mmc/host/sdhci-msm.c b/drivers/mmc/host/sdhci-msm.c
index e44b7a6..64fb85e 100644
--- a/drivers/mmc/host/sdhci-msm.c
+++ b/drivers/mmc/host/sdhci-msm.c
@@ -2089,6 +2089,23 @@ static void sdhci_msm_cqe_disable(struct mmc_host *mmc, bool recovery)
 	sdhci_cqe_disable(mmc, recovery);
 }
 
+static void sdhci_msm_set_timeout(struct sdhci_host *host, struct mmc_command *cmd)
+{
+
+	u32 count, start = 15;
+
+	__sdhci_set_timeout(host, cmd);
+	count = sdhci_readb(host, SDHCI_TIMEOUT_CONTROL);
+	/*
+	 * Update software timeout value if its value is less than hardware data
+	 * timeout value. Qcom SoC hardware data timeout value was calculated
+	 * using 4 * MCLK * 2^(count + 13). where MCLK = 1 / host->clock.
+	 */
+	if (cmd && cmd->data && host->clock > 400000 && host->clock <= 50000000
+			&& ((1 << (count + start)) > (10 * host->clock)))
+		host->data_timeout = 22LL * NSEC_PER_SEC;
+}
+
 static const struct cqhci_host_ops sdhci_msm_cqhci_ops = {
 	.enable		= sdhci_msm_cqe_enable,
 	.disable	= sdhci_msm_cqe_disable,
@@ -2438,6 +2455,7 @@ static const struct sdhci_ops sdhci_msm_ops = {
 	.irq	= sdhci_msm_cqe_irq,
 	.dump_vendor_regs = sdhci_msm_dump_vendor_regs,
 	.set_power = sdhci_set_power_noreg,
+	.set_timeout = sdhci_msm_set_timeout,
 };
 
 static const struct sdhci_pltfm_data sdhci_msm_pdata = {
-- 
QUALCOMM INDIA, on behalf of Qualcomm Innovation Center, Inc. is a member 
of Code Aurora Forum, hosted by The Linux Foundation


             reply	other threads:[~2021-07-05 15:51 UTC|newest]

Thread overview: 3+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2021-07-05 15:50 Shaik Sajida Bhanu [this message]
2021-07-15  5:29 ` [PATCH V3] mmc: sdhci-msm: Update the software timeout value for sdhc Adrian Hunter
2021-07-16  6:18   ` sbhanu

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=1625500253-12815-1-git-send-email-sbhanu@codeaurora.org \
    --to=sbhanu@codeaurora.org \
    --cc=adrian.hunter@intel.com \
    --cc=agross@kernel.org \
    --cc=asutoshd@codeaurora.org \
    --cc=bjorn.andersson@linaro.org \
    --cc=cang@codeaurora.org \
    --cc=linux-arm-msm@vger.kernel.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=linux-mmc@vger.kernel.org \
    --cc=nitirawa@codeaurora.org \
    --cc=pragalla@codeaurora.org \
    --cc=rampraka@codeaurora.org \
    --cc=rnayak@codeaurora.org \
    --cc=robh+dt@kernel.org \
    --cc=sartgarg@codeaurora.org \
    --cc=sayalil@codeaurora.org \
    --cc=stummala@codeaurora.org \
    --cc=ulf.hansson@linaro.org \
    --cc=vbadigan@codeaurora.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body. 
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.