All of lore.kernel.org
 help / color / mirror / Atom feed
From: haibo.chen@nxp.com
To: robh+dt@kernel.org, shawnguo@kernel.org, s.hauer@pengutronix.de
Cc: kernel@pengutronix.de, festevam@gmail.com, linux-imx@nxp.com,
	devicetree@vger.kernel.org, linux-arm-kernel@lists.infradead.org
Subject: [PATCH 1/2] ARM: dts: imx: change the spi-nor tx
Date: Fri, 20 Aug 2021 17:29:49 +0800	[thread overview]
Message-ID: <1629451790-10507-1-git-send-email-haibo.chen@nxp.com> (raw)

From: Haibo Chen <haibo.chen@nxp.com>

Before commit 0e30f47232ab5 ("mtd: spi-nor: add support for DTR protocol"),
for all PP command, it only support 1-1-1 mode, no matter the tx setting
in dts. But after the upper commit, the logic change. It will choose
the best mode(fastest mode) which flash device and spi-nor host controller
both support.

Though the spi-nor device on imx6sx-sdb/imx6ul(l/z)-14x14-evk board
do not support PP-1-4-4/PP-1-1-4, but if tx is 4 in dts file, it will also
impact the read mode selection. For the spi-nor device on the upper mentioned
boards, they support read 1-4-4 mode and read 1-1-4 mode according to the
device internal sfdp register. But qspi host controller do not support
read 1-4-4 mode. so need to set the tx to 1, let the common code finally
select read 1-1-4 mode, PP-1-1-1 mode.

Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
---
 arch/arm/boot/dts/imx6sx-sdb.dts        | 4 ++--
 arch/arm/boot/dts/imx6ul-14x14-evk.dtsi | 2 +-
 2 files changed, 3 insertions(+), 3 deletions(-)

diff --git a/arch/arm/boot/dts/imx6sx-sdb.dts b/arch/arm/boot/dts/imx6sx-sdb.dts
index 5a63ca615722..99f4cf777a38 100644
--- a/arch/arm/boot/dts/imx6sx-sdb.dts
+++ b/arch/arm/boot/dts/imx6sx-sdb.dts
@@ -114,7 +114,7 @@
 		compatible = "micron,n25q256a", "jedec,spi-nor";
 		spi-max-frequency = <29000000>;
 		spi-rx-bus-width = <4>;
-		spi-tx-bus-width = <4>;
+		spi-tx-bus-width = <1>;
 		reg = <0>;
 	};
 
@@ -124,7 +124,7 @@
 		compatible = "micron,n25q256a", "jedec,spi-nor";
 		spi-max-frequency = <29000000>;
 		spi-rx-bus-width = <4>;
-		spi-tx-bus-width = <4>;
+		spi-tx-bus-width = <1>;
 		reg = <2>;
 	};
 };
diff --git a/arch/arm/boot/dts/imx6ul-14x14-evk.dtsi b/arch/arm/boot/dts/imx6ul-14x14-evk.dtsi
index 779cc536566d..a3fde3316c73 100644
--- a/arch/arm/boot/dts/imx6ul-14x14-evk.dtsi
+++ b/arch/arm/boot/dts/imx6ul-14x14-evk.dtsi
@@ -292,7 +292,7 @@
 		compatible = "micron,n25q256a", "jedec,spi-nor";
 		spi-max-frequency = <29000000>;
 		spi-rx-bus-width = <4>;
-		spi-tx-bus-width = <4>;
+		spi-tx-bus-width = <1>;
 		reg = <0>;
 	};
 };
-- 
2.17.1


WARNING: multiple messages have this Message-ID (diff)
From: haibo.chen@nxp.com
To: robh+dt@kernel.org, shawnguo@kernel.org, s.hauer@pengutronix.de
Cc: kernel@pengutronix.de, festevam@gmail.com, linux-imx@nxp.com,
	devicetree@vger.kernel.org, linux-arm-kernel@lists.infradead.org
Subject: [PATCH 1/2] ARM: dts: imx: change the spi-nor tx
Date: Fri, 20 Aug 2021 17:29:49 +0800	[thread overview]
Message-ID: <1629451790-10507-1-git-send-email-haibo.chen@nxp.com> (raw)

From: Haibo Chen <haibo.chen@nxp.com>

Before commit 0e30f47232ab5 ("mtd: spi-nor: add support for DTR protocol"),
for all PP command, it only support 1-1-1 mode, no matter the tx setting
in dts. But after the upper commit, the logic change. It will choose
the best mode(fastest mode) which flash device and spi-nor host controller
both support.

Though the spi-nor device on imx6sx-sdb/imx6ul(l/z)-14x14-evk board
do not support PP-1-4-4/PP-1-1-4, but if tx is 4 in dts file, it will also
impact the read mode selection. For the spi-nor device on the upper mentioned
boards, they support read 1-4-4 mode and read 1-1-4 mode according to the
device internal sfdp register. But qspi host controller do not support
read 1-4-4 mode. so need to set the tx to 1, let the common code finally
select read 1-1-4 mode, PP-1-1-1 mode.

Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
---
 arch/arm/boot/dts/imx6sx-sdb.dts        | 4 ++--
 arch/arm/boot/dts/imx6ul-14x14-evk.dtsi | 2 +-
 2 files changed, 3 insertions(+), 3 deletions(-)

diff --git a/arch/arm/boot/dts/imx6sx-sdb.dts b/arch/arm/boot/dts/imx6sx-sdb.dts
index 5a63ca615722..99f4cf777a38 100644
--- a/arch/arm/boot/dts/imx6sx-sdb.dts
+++ b/arch/arm/boot/dts/imx6sx-sdb.dts
@@ -114,7 +114,7 @@
 		compatible = "micron,n25q256a", "jedec,spi-nor";
 		spi-max-frequency = <29000000>;
 		spi-rx-bus-width = <4>;
-		spi-tx-bus-width = <4>;
+		spi-tx-bus-width = <1>;
 		reg = <0>;
 	};
 
@@ -124,7 +124,7 @@
 		compatible = "micron,n25q256a", "jedec,spi-nor";
 		spi-max-frequency = <29000000>;
 		spi-rx-bus-width = <4>;
-		spi-tx-bus-width = <4>;
+		spi-tx-bus-width = <1>;
 		reg = <2>;
 	};
 };
diff --git a/arch/arm/boot/dts/imx6ul-14x14-evk.dtsi b/arch/arm/boot/dts/imx6ul-14x14-evk.dtsi
index 779cc536566d..a3fde3316c73 100644
--- a/arch/arm/boot/dts/imx6ul-14x14-evk.dtsi
+++ b/arch/arm/boot/dts/imx6ul-14x14-evk.dtsi
@@ -292,7 +292,7 @@
 		compatible = "micron,n25q256a", "jedec,spi-nor";
 		spi-max-frequency = <29000000>;
 		spi-rx-bus-width = <4>;
-		spi-tx-bus-width = <4>;
+		spi-tx-bus-width = <1>;
 		reg = <0>;
 	};
 };
-- 
2.17.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

             reply	other threads:[~2021-08-20  9:51 UTC|newest]

Thread overview: 6+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2021-08-20  9:29 haibo.chen [this message]
2021-08-20  9:29 ` [PATCH 1/2] ARM: dts: imx: change the spi-nor tx haibo.chen
2021-08-20  9:29 ` [PATCH 2/2] arm64: dts: imx8: " haibo.chen
2021-08-20  9:29   ` haibo.chen
2021-10-04  3:25 ` [PATCH 1/2] ARM: dts: imx: " Shawn Guo
2021-10-04  3:25   ` Shawn Guo

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=1629451790-10507-1-git-send-email-haibo.chen@nxp.com \
    --to=haibo.chen@nxp.com \
    --cc=devicetree@vger.kernel.org \
    --cc=festevam@gmail.com \
    --cc=kernel@pengutronix.de \
    --cc=linux-arm-kernel@lists.infradead.org \
    --cc=linux-imx@nxp.com \
    --cc=robh+dt@kernel.org \
    --cc=s.hauer@pengutronix.de \
    --cc=shawnguo@kernel.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body. 
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.