All of lore.kernel.org
 help / color / mirror / Atom feed
From: Martin Fuzzey <martin.fuzzey@flowbird.group>
To: linux-wireless@vger.kernel.org
Cc: Amitkumar Karwar <amitkarwar@gmail.com>,
	Siva Rebbagondla <siva8118@gmail.com>,
	Kalle Valo <kvalo@codeaurora.org>,
	Jakub Kicinski <kuba@kernel.org>,
	Prameela Rani Garnepudi <prameela.j04cs@gmail.com>,
	linux-kernel@vger.kernel.org,
	Martin Fuzzey <martin.fuzzey@flowbird.group>
Subject: [PATCH v2 3/3] rsi: fix rate mask set leading to P2P failure
Date: Mon, 30 Aug 2021 17:26:46 +0200	[thread overview]
Message-ID: <1630337206-12410-4-git-send-email-martin.fuzzey@flowbird.group> (raw)
In-Reply-To: <1630337206-12410-1-git-send-email-martin.fuzzey@flowbird.group>

P2P client mode was only working the first time.
On subsequent connection attempts the group was successfully created but
no data was sent (no transmitted data packets were seen with a sniffer).

The reason for this was that the hardware was being configured in fixed
rate mode with rate RSI_RATE_1 (1Mbps) which is not valid in the 5GHz band.

In P2P mode wpa_supplicant uses NL80211_CMD_SET_TX_BITRATE_MASK to disallow
the 11b rates in the 2.4GHz band which updated common->fixedrate_mask.

rsi_set_min_rate() then used the fixedrate_mask to calculate the minimum
allowed rate, or 0xffff = auto if none was found.
However that calculation did not account for the different rate sets
allowed in the different bands leading to the error.

Fixing set_min_rate() would result in 6Mb/s being used all the time
which is not what we want either.

The reason the problem did not occur on the first connection is that
rsi_mac80211_set_rate_mask() only updated the fixedrate_mask for
the *current* band. When it was called that was still 2.4GHz as the
switch is done later. So the when set_min_rate() was subsequently
called after the switch to 5GHz it still had a mask of zero, leading
to defaulting to auto mode.

Fix this by differentiating the case of a single rate being
requested, in which case the hardware will be used in fixed rate
mode with just that rate, and multiple rates being requested,
in which case we remain in auto mode but the firmware rate selection
algorithm is configured with a restricted set of rates.

Fixes: dad0d04fa7ba ("rsi: Add RS9113 wireless driver")
Signed-off-by: Martin Fuzzey <martin.fuzzey@flowbird.group>
CC: stable@vger.kernel.org
---
 drivers/net/wireless/rsi/rsi_91x_hal.c      |  8 ++--
 drivers/net/wireless/rsi/rsi_91x_mac80211.c | 74 +++++++++--------------------
 drivers/net/wireless/rsi/rsi_91x_mgmt.c     | 21 +++++---
 drivers/net/wireless/rsi/rsi_main.h         | 12 +++--
 4 files changed, 50 insertions(+), 65 deletions(-)

diff --git a/drivers/net/wireless/rsi/rsi_91x_hal.c b/drivers/net/wireless/rsi/rsi_91x_hal.c
index 2aa9f0b..dca81a4 100644
--- a/drivers/net/wireless/rsi/rsi_91x_hal.c
+++ b/drivers/net/wireless/rsi/rsi_91x_hal.c
@@ -214,15 +214,17 @@ int rsi_prepare_data_desc(struct rsi_common *common, struct sk_buff *skb)
 			RSI_WIFI_DATA_Q);
 	data_desc->header_len = ieee80211_size;
 
-	if (common->min_rate != RSI_RATE_AUTO) {
+	if (common->rate_config[common->band].fixed_enabled) {
 		/* Send fixed rate */
+		u16 fixed_rate = common->rate_config[common->band].fixed_hw_rate;
+
 		data_desc->frame_info = cpu_to_le16(RATE_INFO_ENABLE);
-		data_desc->rate_info = cpu_to_le16(common->min_rate);
+		data_desc->rate_info = cpu_to_le16(fixed_rate);
 
 		if (conf_is_ht40(&common->priv->hw->conf))
 			data_desc->bbp_info = cpu_to_le16(FULL40M_ENABLE);
 
-		if ((common->vif_info[0].sgi) && (common->min_rate & 0x100)) {
+		if (common->vif_info[0].sgi && (fixed_rate & 0x100)) {
 		       /* Only MCS rates */
 			data_desc->rate_info |=
 				cpu_to_le16(ENABLE_SHORTGI_RATE);
diff --git a/drivers/net/wireless/rsi/rsi_91x_mac80211.c b/drivers/net/wireless/rsi/rsi_91x_mac80211.c
index b66975f..e70c1c7f 100644
--- a/drivers/net/wireless/rsi/rsi_91x_mac80211.c
+++ b/drivers/net/wireless/rsi/rsi_91x_mac80211.c
@@ -510,7 +510,6 @@ static int rsi_mac80211_add_interface(struct ieee80211_hw *hw,
 	if ((vif->type == NL80211_IFTYPE_AP) ||
 	    (vif->type == NL80211_IFTYPE_P2P_GO)) {
 		rsi_send_rx_filter_frame(common, DISALLOW_BEACONS);
-		common->min_rate = RSI_RATE_AUTO;
 		for (i = 0; i < common->max_stations; i++)
 			common->stations[i].sta = NULL;
 	}
@@ -1228,20 +1227,32 @@ static int rsi_mac80211_set_rate_mask(struct ieee80211_hw *hw,
 				      struct ieee80211_vif *vif,
 				      const struct cfg80211_bitrate_mask *mask)
 {
+	const unsigned int mcs_offset = ARRAY_SIZE(rsi_rates);
 	struct rsi_hw *adapter = hw->priv;
 	struct rsi_common *common = adapter->priv;
-	enum nl80211_band band = hw->conf.chandef.chan->band;
+	int i;
 
 	mutex_lock(&common->mutex);
-	common->fixedrate_mask[band] = 0;
 
-	if (mask->control[band].legacy == 0xfff) {
-		common->fixedrate_mask[band] =
-			(mask->control[band].ht_mcs[0] << 12);
-	} else {
-		common->fixedrate_mask[band] =
-			mask->control[band].legacy;
+	for (i = 0; i < ARRAY_SIZE(common->rate_config); i++) {
+		struct rsi_rate_config *cfg = &common->rate_config[i];
+		u32 bm;
+
+		bm = mask->control[i].legacy | (mask->control[i].ht_mcs[0] << mcs_offset);
+		if (hweight32(bm) == 1) { /* single rate */
+			int rate_index = ffs(bm) - 1;
+
+			if (rate_index < mcs_offset)
+				cfg->fixed_hw_rate = rsi_rates[rate_index].hw_value;
+			else
+				cfg->fixed_hw_rate = rsi_mcsrates[rate_index - mcs_offset];
+			cfg->fixed_enabled = true;
+		} else {
+			cfg->configured_mask = bm;
+			cfg->fixed_enabled = false;
+		}
 	}
+
 	mutex_unlock(&common->mutex);
 
 	return 0;
@@ -1378,46 +1389,6 @@ void rsi_indicate_pkt_to_os(struct rsi_common *common,
 	ieee80211_rx_irqsafe(hw, skb);
 }
 
-static void rsi_set_min_rate(struct ieee80211_hw *hw,
-			     struct ieee80211_sta *sta,
-			     struct rsi_common *common)
-{
-	u8 band = hw->conf.chandef.chan->band;
-	u8 ii;
-	u32 rate_bitmap;
-	bool matched = false;
-
-	common->bitrate_mask[band] = sta->supp_rates[band];
-
-	rate_bitmap = (common->fixedrate_mask[band] & sta->supp_rates[band]);
-
-	if (rate_bitmap & 0xfff) {
-		/* Find out the min rate */
-		for (ii = 0; ii < ARRAY_SIZE(rsi_rates); ii++) {
-			if (rate_bitmap & BIT(ii)) {
-				common->min_rate = rsi_rates[ii].hw_value;
-				matched = true;
-				break;
-			}
-		}
-	}
-
-	common->vif_info[0].is_ht = sta->ht_cap.ht_supported;
-
-	if ((common->vif_info[0].is_ht) && (rate_bitmap >> 12)) {
-		for (ii = 0; ii < ARRAY_SIZE(rsi_mcsrates); ii++) {
-			if ((rate_bitmap >> 12) & BIT(ii)) {
-				common->min_rate = rsi_mcsrates[ii];
-				matched = true;
-				break;
-			}
-		}
-	}
-
-	if (!matched)
-		common->min_rate = 0xffff;
-}
-
 /**
  * rsi_mac80211_sta_add() - This function notifies driver about a peer getting
  *			    connected.
@@ -1516,9 +1487,9 @@ static int rsi_mac80211_sta_add(struct ieee80211_hw *hw,
 
 	if ((vif->type == NL80211_IFTYPE_STATION) ||
 	    (vif->type == NL80211_IFTYPE_P2P_CLIENT)) {
-		rsi_set_min_rate(hw, sta, common);
+		common->bitrate_mask[common->band] = sta->supp_rates[common->band];
+		common->vif_info[0].is_ht = sta->ht_cap.ht_supported;
 		if (sta->ht_cap.ht_supported) {
-			common->vif_info[0].is_ht = true;
 			common->bitrate_mask[NL80211_BAND_2GHZ] =
 					sta->supp_rates[NL80211_BAND_2GHZ];
 			if ((sta->ht_cap.cap & IEEE80211_HT_CAP_SGI_20) ||
@@ -1592,7 +1563,6 @@ static int rsi_mac80211_sta_remove(struct ieee80211_hw *hw,
 		bss->qos = sta->wme;
 		common->bitrate_mask[NL80211_BAND_2GHZ] = 0;
 		common->bitrate_mask[NL80211_BAND_5GHZ] = 0;
-		common->min_rate = 0xffff;
 		common->vif_info[0].is_ht = false;
 		common->vif_info[0].sgi = false;
 		common->vif_info[0].seq_start = 0;
diff --git a/drivers/net/wireless/rsi/rsi_91x_mgmt.c b/drivers/net/wireless/rsi/rsi_91x_mgmt.c
index a25742a..0848f7a 100644
--- a/drivers/net/wireless/rsi/rsi_91x_mgmt.c
+++ b/drivers/net/wireless/rsi/rsi_91x_mgmt.c
@@ -276,7 +276,7 @@ static void rsi_set_default_parameters(struct rsi_common *common)
 	common->channel_width = BW_20MHZ;
 	common->rts_threshold = IEEE80211_MAX_RTS_THRESHOLD;
 	common->channel = 1;
-	common->min_rate = 0xffff;
+	memset(&common->rate_config, 0, sizeof(common->rate_config));
 	common->fsm_state = FSM_CARD_NOT_READY;
 	common->iface_down = true;
 	common->endpoint = EP_2GHZ_20MHZ;
@@ -1314,7 +1314,7 @@ static int rsi_send_auto_rate_request(struct rsi_common *common,
 	u8 band = hw->conf.chandef.chan->band;
 	u8 num_supported_rates = 0;
 	u8 rate_table_offset, rate_offset = 0;
-	u32 rate_bitmap;
+	u32 rate_bitmap, configured_rates;
 	u16 *selected_rates, min_rate;
 	bool is_ht = false, is_sgi = false;
 	u16 frame_len = sizeof(struct rsi_auto_rate);
@@ -1364,6 +1364,10 @@ static int rsi_send_auto_rate_request(struct rsi_common *common,
 			is_sgi = true;
 	}
 
+	/* Limit to any rates administratively configured by cfg80211 */
+	configured_rates = common->rate_config[band].configured_mask ?: 0xffffffff;
+	rate_bitmap &= configured_rates;
+
 	if (band == NL80211_BAND_2GHZ) {
 		if ((rate_bitmap == 0) && (is_ht))
 			min_rate = RSI_RATE_MCS0;
@@ -1389,10 +1393,13 @@ static int rsi_send_auto_rate_request(struct rsi_common *common,
 	num_supported_rates = jj;
 
 	if (is_ht) {
-		for (ii = 0; ii < ARRAY_SIZE(mcs); ii++)
-			selected_rates[jj++] = mcs[ii];
-		num_supported_rates += ARRAY_SIZE(mcs);
-		rate_offset += ARRAY_SIZE(mcs);
+		for (ii = 0; ii < ARRAY_SIZE(mcs); ii++) {
+			if (configured_rates & BIT(ii + ARRAY_SIZE(rsi_rates))) {
+				selected_rates[jj++] = mcs[ii];
+				num_supported_rates++;
+				rate_offset++;
+			}
+		}
 	}
 
 	sort(selected_rates, jj, sizeof(u16), &rsi_compare, NULL);
@@ -1482,7 +1489,7 @@ void rsi_inform_bss_status(struct rsi_common *common,
 					      qos_enable,
 					      aid, sta_id,
 					      vif);
-		if (common->min_rate == 0xffff)
+		if (!common->rate_config[common->band].fixed_enabled)
 			rsi_send_auto_rate_request(common, sta, sta_id, vif);
 		if (opmode == RSI_OPMODE_STA &&
 		    !(assoc_cap & WLAN_CAPABILITY_PRIVACY) &&
diff --git a/drivers/net/wireless/rsi/rsi_main.h b/drivers/net/wireless/rsi/rsi_main.h
index 810485a..dcf8fb4 100644
--- a/drivers/net/wireless/rsi/rsi_main.h
+++ b/drivers/net/wireless/rsi/rsi_main.h
@@ -61,6 +61,7 @@ enum RSI_FSM_STATES {
 extern u32 rsi_zone_enabled;
 extern __printf(2, 3) void rsi_dbg(u32 zone, const char *fmt, ...);
 
+#define RSI_MAX_BANDS			2
 #define RSI_MAX_VIFS                    3
 #define NUM_EDCA_QUEUES                 4
 #define IEEE80211_ADDR_LEN              6
@@ -230,6 +231,12 @@ struct rsi_9116_features {
 	u32 ps_options;
 };
 
+struct rsi_rate_config {
+	u32 configured_mask;	/* configured by mac80211 bits 0-11=legacy 12+ mcs */
+	u16 fixed_hw_rate;
+	bool fixed_enabled;
+};
+
 struct rsi_common {
 	struct rsi_hw *priv;
 	struct vif_priv vif_info[RSI_MAX_VIFS];
@@ -255,8 +262,8 @@ struct rsi_common {
 	u8 channel_width;
 
 	u16 rts_threshold;
-	u16 bitrate_mask[2];
-	u32 fixedrate_mask[2];
+	u32 bitrate_mask[RSI_MAX_BANDS];
+	struct rsi_rate_config rate_config[RSI_MAX_BANDS];
 
 	u8 rf_reset;
 	struct transmit_q_stats tx_stats;
@@ -277,7 +284,6 @@ struct rsi_common {
 	u8 mac_id;
 	u8 radio_id;
 	u16 rate_pwr[20];
-	u16 min_rate;
 
 	/* WMM algo related */
 	u8 selected_qnum;
-- 
1.9.1


  parent reply	other threads:[~2021-08-30 15:26 UTC|newest]

Thread overview: 6+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2021-08-30 15:26 [PATCH v2 0/3] rsi: fix startup and P2P mode Martin Fuzzey
2021-08-30 15:26 ` [PATCH v2 1/3] rsi: fix occasional initialisation failure with BT coex Martin Fuzzey
2021-09-21  5:43   ` Kalle Valo
2021-08-30 15:26 ` [PATCH v2 2/3] rsi: fix key enabled check causing unwanted encryption for vap_id > 0 Martin Fuzzey
2021-08-30 15:26 ` Martin Fuzzey [this message]
2021-09-21  5:49 ` [PATCH v2 0/3] rsi: fix startup and P2P mode Kalle Valo

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=1630337206-12410-4-git-send-email-martin.fuzzey@flowbird.group \
    --to=martin.fuzzey@flowbird.group \
    --cc=amitkarwar@gmail.com \
    --cc=kuba@kernel.org \
    --cc=kvalo@codeaurora.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=linux-wireless@vger.kernel.org \
    --cc=prameela.j04cs@gmail.com \
    --cc=siva8118@gmail.com \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.