From: Andy Green <andy.green@linaro.org>
To: linux-omap@vger.kernel.org
Cc: s-jan@ti.com, arnd@arndb.de, patches@linaro.org,
tony@atomide.com, netdev@vger.kernel.org,
linux-kernel@vger.kernel.org, rostedt@goodmis.org,
linux-arm-kernel@lists.infradead.org
Subject: [PATCH 4 4/4] config test config extending omap2plus with wl12xx etc
Date: Thu, 05 Jul 2012 10:45:03 +0800 [thread overview]
Message-ID: <20120705024501.26317.53085.stgit@build.warmcat.com> (raw)
In-Reply-To: <20120705024259.26317.16000.stgit@build.warmcat.com>
From: Andy Green <andy@warmcat.com>
This is just provided for testing convenience, it has enough config
options to get Ethernet and WL12xx driver on PandaBoard / ES up
You should be able to reproduce something like this, with different
MAC addresses.
# ifconfig -a
eth0 Link encap:Ethernet HWaddr 2e:20:3c:ea:46:01
inet addr:10.42.0.98 Bcast:10.42.0.255 Mask:255.255.255.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:13 errors:0 dropped:0 overruns:0 frame:0
TX packets:31 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:1647 (1.6 KB) TX bytes:5534 (5.5 KB)
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:2 errors:0 dropped:0 overruns:0 frame:0
TX packets:2 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:100 (100.0 B) TX bytes:100 (100.0 B)
wlan0 Link encap:Ethernet HWaddr 2e:60:3c:ea:46:01
BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
Signed-off-by: Andy Green <andy.green@linaro.org>
---
arch/arm/configs/omap2plus_defconfig | 35 ++++++++++++++--------------------
1 file changed, 14 insertions(+), 21 deletions(-)
diff --git a/arch/arm/configs/omap2plus_defconfig b/arch/arm/configs/omap2plus_defconfig
index f3087cb..7dcd384 100644
--- a/arch/arm/configs/omap2plus_defconfig
+++ b/arch/arm/configs/omap2plus_defconfig
@@ -2,13 +2,13 @@ CONFIG_EXPERIMENTAL=y
CONFIG_SYSVIPC=y
CONFIG_POSIX_MQUEUE=y
CONFIG_BSD_PROCESS_ACCT=y
+CONFIG_NO_HZ=y
+CONFIG_HIGH_RES_TIMERS=y
CONFIG_IKCONFIG=y
CONFIG_IKCONFIG_PROC=y
CONFIG_LOG_BUF_SHIFT=16
CONFIG_BLK_DEV_INITRD=y
CONFIG_EXPERT=y
-# CONFIG_SYSCTL_SYSCALL is not set
-CONFIG_KALLSYMS_EXTRA_PASS=y
CONFIG_SLAB=y
CONFIG_PROFILING=y
CONFIG_OPROFILE=y
@@ -20,13 +20,12 @@ CONFIG_MODULE_FORCE_UNLOAD=y
CONFIG_MODVERSIONS=y
CONFIG_MODULE_SRCVERSION_ALL=y
# CONFIG_BLK_DEV_BSG is not set
+CONFIG_PARTITION_ADVANCED=y
CONFIG_ARCH_OMAP=y
CONFIG_OMAP_RESET_CLOCKS=y
CONFIG_OMAP_MUX_DEBUG=y
CONFIG_ARM_THUMBEE=y
CONFIG_ARM_ERRATA_411920=y
-CONFIG_NO_HZ=y
-CONFIG_HIGH_RES_TIMERS=y
CONFIG_SMP=y
CONFIG_NR_CPUS=2
CONFIG_LEDS=y
@@ -60,6 +59,7 @@ CONFIG_BT_HCIUART_LL=y
CONFIG_BT_HCIBCM203X=m
CONFIG_BT_HCIBPA10X=m
CONFIG_CFG80211=m
+CONFIG_LIB80211=m
CONFIG_MAC80211=m
CONFIG_MAC80211_RC_PID=y
CONFIG_MAC80211_RC_DEFAULT_PID=y
@@ -87,22 +87,20 @@ CONFIG_SCSI_MULTI_LUN=y
CONFIG_SCSI_SCAN_ASYNC=y
CONFIG_MD=y
CONFIG_NETDEVICES=y
-CONFIG_SMSC_PHY=y
-CONFIG_NET_ETHERNET=y
-CONFIG_SMC91X=y
-CONFIG_SMSC911X=y
CONFIG_KS8851=y
CONFIG_KS8851_MLL=y
-CONFIG_LIBERTAS=m
-CONFIG_LIBERTAS_USB=m
-CONFIG_LIBERTAS_SDIO=m
-CONFIG_LIBERTAS_DEBUG=y
+CONFIG_SMC91X=y
+CONFIG_SMSC911X=y
+CONFIG_SMSC_PHY=y
CONFIG_USB_USBNET=y
CONFIG_USB_NET_SMSC95XX=y
CONFIG_USB_ALI_M5632=y
CONFIG_USB_AN2720=y
CONFIG_USB_EPSON2888=y
CONFIG_USB_KC2190=y
+CONFIG_WL_TI=y
+CONFIG_WL12XX=m
+CONFIG_WLCORE_SDIO=m
CONFIG_INPUT_JOYDEV=y
CONFIG_INPUT_EVDEV=y
CONFIG_KEYBOARD_GPIO=y
@@ -131,14 +129,14 @@ CONFIG_POWER_SUPPLY=y
CONFIG_WATCHDOG=y
CONFIG_OMAP_WATCHDOG=y
CONFIG_TWL4030_WATCHDOG=y
-CONFIG_REGULATOR_TWL4030=y
+CONFIG_MFD_WL1273_CORE=y
CONFIG_REGULATOR_TPS65023=y
CONFIG_REGULATOR_TPS6507X=y
+CONFIG_REGULATOR_TWL4030=y
CONFIG_FB=y
CONFIG_FIRMWARE_EDID=y
CONFIG_FB_MODE_HELPERS=y
CONFIG_FB_TILEBLITTING=y
-CONFIG_FB_OMAP_LCD_VGA=y
CONFIG_OMAP2_DSS=m
CONFIG_OMAP2_DSS_RFBI=y
CONFIG_OMAP2_DSS_SDI=y
@@ -153,7 +151,6 @@ CONFIG_PANEL_ACX565AKM=m
CONFIG_BACKLIGHT_LCD_SUPPORT=y
CONFIG_LCD_CLASS_DEVICE=y
CONFIG_LCD_PLATFORM=y
-CONFIG_DISPLAY_SUPPORT=y
CONFIG_FRAMEBUFFER_CONSOLE=y
CONFIG_FRAMEBUFFER_CONSOLE_ROTATION=y
CONFIG_FONTS=y
@@ -173,7 +170,6 @@ CONFIG_SND_OMAP_SOC_OMAP3_PANDORA=m
CONFIG_USB=y
CONFIG_USB_DEBUG=y
CONFIG_USB_ANNOUNCE_NEW_DEVICES=y
-CONFIG_USB_DEVICEFS=y
CONFIG_USB_SUSPEND=y
CONFIG_USB_MON=y
CONFIG_USB_EHCI_HCD=y
@@ -212,23 +208,20 @@ CONFIG_JFFS2_RUBIN=y
CONFIG_UBIFS_FS=y
CONFIG_CRAMFS=y
CONFIG_NFS_FS=y
-CONFIG_NFS_V3=y
CONFIG_NFS_V3_ACL=y
CONFIG_NFS_V4=y
CONFIG_ROOT_NFS=y
-CONFIG_PARTITION_ADVANCED=y
CONFIG_NLS_CODEPAGE_437=y
CONFIG_NLS_ISO8859_1=y
CONFIG_PRINTK_TIME=y
CONFIG_MAGIC_SYSRQ=y
-CONFIG_DEBUG_KERNEL=y
CONFIG_SCHEDSTATS=y
CONFIG_TIMER_STATS=y
CONFIG_PROVE_LOCKING=y
-CONFIG_DEBUG_SPINLOCK_SLEEP=y
# CONFIG_DEBUG_BUGVERBOSE is not set
CONFIG_DEBUG_INFO=y
-# CONFIG_RCU_CPU_STALL_DETECTOR is not set
+CONFIG_DEBUG_LL=y
+CONFIG_EARLY_PRINTK=y
CONFIG_SECURITY=y
CONFIG_CRYPTO_MICHAEL_MIC=y
# CONFIG_CRYPTO_ANSI_CPRNG is not set
WARNING: multiple messages have this Message-ID (diff)
From: andy.green@linaro.org (Andy Green)
To: linux-arm-kernel@lists.infradead.org
Subject: [PATCH 4 4/4] config test config extending omap2plus with wl12xx etc
Date: Thu, 05 Jul 2012 10:45:03 +0800 [thread overview]
Message-ID: <20120705024501.26317.53085.stgit@build.warmcat.com> (raw)
In-Reply-To: <20120705024259.26317.16000.stgit@build.warmcat.com>
From: Andy Green <andy@warmcat.com>
This is just provided for testing convenience, it has enough config
options to get Ethernet and WL12xx driver on PandaBoard / ES up
You should be able to reproduce something like this, with different
MAC addresses.
# ifconfig -a
eth0 Link encap:Ethernet HWaddr 2e:20:3c:ea:46:01
inet addr:10.42.0.98 Bcast:10.42.0.255 Mask:255.255.255.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:13 errors:0 dropped:0 overruns:0 frame:0
TX packets:31 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:1647 (1.6 KB) TX bytes:5534 (5.5 KB)
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:2 errors:0 dropped:0 overruns:0 frame:0
TX packets:2 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:100 (100.0 B) TX bytes:100 (100.0 B)
wlan0 Link encap:Ethernet HWaddr 2e:60:3c:ea:46:01
BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
Signed-off-by: Andy Green <andy.green@linaro.org>
---
arch/arm/configs/omap2plus_defconfig | 35 ++++++++++++++--------------------
1 file changed, 14 insertions(+), 21 deletions(-)
diff --git a/arch/arm/configs/omap2plus_defconfig b/arch/arm/configs/omap2plus_defconfig
index f3087cb..7dcd384 100644
--- a/arch/arm/configs/omap2plus_defconfig
+++ b/arch/arm/configs/omap2plus_defconfig
@@ -2,13 +2,13 @@ CONFIG_EXPERIMENTAL=y
CONFIG_SYSVIPC=y
CONFIG_POSIX_MQUEUE=y
CONFIG_BSD_PROCESS_ACCT=y
+CONFIG_NO_HZ=y
+CONFIG_HIGH_RES_TIMERS=y
CONFIG_IKCONFIG=y
CONFIG_IKCONFIG_PROC=y
CONFIG_LOG_BUF_SHIFT=16
CONFIG_BLK_DEV_INITRD=y
CONFIG_EXPERT=y
-# CONFIG_SYSCTL_SYSCALL is not set
-CONFIG_KALLSYMS_EXTRA_PASS=y
CONFIG_SLAB=y
CONFIG_PROFILING=y
CONFIG_OPROFILE=y
@@ -20,13 +20,12 @@ CONFIG_MODULE_FORCE_UNLOAD=y
CONFIG_MODVERSIONS=y
CONFIG_MODULE_SRCVERSION_ALL=y
# CONFIG_BLK_DEV_BSG is not set
+CONFIG_PARTITION_ADVANCED=y
CONFIG_ARCH_OMAP=y
CONFIG_OMAP_RESET_CLOCKS=y
CONFIG_OMAP_MUX_DEBUG=y
CONFIG_ARM_THUMBEE=y
CONFIG_ARM_ERRATA_411920=y
-CONFIG_NO_HZ=y
-CONFIG_HIGH_RES_TIMERS=y
CONFIG_SMP=y
CONFIG_NR_CPUS=2
CONFIG_LEDS=y
@@ -60,6 +59,7 @@ CONFIG_BT_HCIUART_LL=y
CONFIG_BT_HCIBCM203X=m
CONFIG_BT_HCIBPA10X=m
CONFIG_CFG80211=m
+CONFIG_LIB80211=m
CONFIG_MAC80211=m
CONFIG_MAC80211_RC_PID=y
CONFIG_MAC80211_RC_DEFAULT_PID=y
@@ -87,22 +87,20 @@ CONFIG_SCSI_MULTI_LUN=y
CONFIG_SCSI_SCAN_ASYNC=y
CONFIG_MD=y
CONFIG_NETDEVICES=y
-CONFIG_SMSC_PHY=y
-CONFIG_NET_ETHERNET=y
-CONFIG_SMC91X=y
-CONFIG_SMSC911X=y
CONFIG_KS8851=y
CONFIG_KS8851_MLL=y
-CONFIG_LIBERTAS=m
-CONFIG_LIBERTAS_USB=m
-CONFIG_LIBERTAS_SDIO=m
-CONFIG_LIBERTAS_DEBUG=y
+CONFIG_SMC91X=y
+CONFIG_SMSC911X=y
+CONFIG_SMSC_PHY=y
CONFIG_USB_USBNET=y
CONFIG_USB_NET_SMSC95XX=y
CONFIG_USB_ALI_M5632=y
CONFIG_USB_AN2720=y
CONFIG_USB_EPSON2888=y
CONFIG_USB_KC2190=y
+CONFIG_WL_TI=y
+CONFIG_WL12XX=m
+CONFIG_WLCORE_SDIO=m
CONFIG_INPUT_JOYDEV=y
CONFIG_INPUT_EVDEV=y
CONFIG_KEYBOARD_GPIO=y
@@ -131,14 +129,14 @@ CONFIG_POWER_SUPPLY=y
CONFIG_WATCHDOG=y
CONFIG_OMAP_WATCHDOG=y
CONFIG_TWL4030_WATCHDOG=y
-CONFIG_REGULATOR_TWL4030=y
+CONFIG_MFD_WL1273_CORE=y
CONFIG_REGULATOR_TPS65023=y
CONFIG_REGULATOR_TPS6507X=y
+CONFIG_REGULATOR_TWL4030=y
CONFIG_FB=y
CONFIG_FIRMWARE_EDID=y
CONFIG_FB_MODE_HELPERS=y
CONFIG_FB_TILEBLITTING=y
-CONFIG_FB_OMAP_LCD_VGA=y
CONFIG_OMAP2_DSS=m
CONFIG_OMAP2_DSS_RFBI=y
CONFIG_OMAP2_DSS_SDI=y
@@ -153,7 +151,6 @@ CONFIG_PANEL_ACX565AKM=m
CONFIG_BACKLIGHT_LCD_SUPPORT=y
CONFIG_LCD_CLASS_DEVICE=y
CONFIG_LCD_PLATFORM=y
-CONFIG_DISPLAY_SUPPORT=y
CONFIG_FRAMEBUFFER_CONSOLE=y
CONFIG_FRAMEBUFFER_CONSOLE_ROTATION=y
CONFIG_FONTS=y
@@ -173,7 +170,6 @@ CONFIG_SND_OMAP_SOC_OMAP3_PANDORA=m
CONFIG_USB=y
CONFIG_USB_DEBUG=y
CONFIG_USB_ANNOUNCE_NEW_DEVICES=y
-CONFIG_USB_DEVICEFS=y
CONFIG_USB_SUSPEND=y
CONFIG_USB_MON=y
CONFIG_USB_EHCI_HCD=y
@@ -212,23 +208,20 @@ CONFIG_JFFS2_RUBIN=y
CONFIG_UBIFS_FS=y
CONFIG_CRAMFS=y
CONFIG_NFS_FS=y
-CONFIG_NFS_V3=y
CONFIG_NFS_V3_ACL=y
CONFIG_NFS_V4=y
CONFIG_ROOT_NFS=y
-CONFIG_PARTITION_ADVANCED=y
CONFIG_NLS_CODEPAGE_437=y
CONFIG_NLS_ISO8859_1=y
CONFIG_PRINTK_TIME=y
CONFIG_MAGIC_SYSRQ=y
-CONFIG_DEBUG_KERNEL=y
CONFIG_SCHEDSTATS=y
CONFIG_TIMER_STATS=y
CONFIG_PROVE_LOCKING=y
-CONFIG_DEBUG_SPINLOCK_SLEEP=y
# CONFIG_DEBUG_BUGVERBOSE is not set
CONFIG_DEBUG_INFO=y
-# CONFIG_RCU_CPU_STALL_DETECTOR is not set
+CONFIG_DEBUG_LL=y
+CONFIG_EARLY_PRINTK=y
CONFIG_SECURITY=y
CONFIG_CRYPTO_MICHAEL_MIC=y
# CONFIG_CRYPTO_ANSI_CPRNG is not set
next prev parent reply other threads:[~2012-07-05 2:55 UTC|newest]
Thread overview: 29+ messages / expand[flat|nested] mbox.gz Atom feed top
2012-07-05 2:44 [PATCH 4 0/4] Add ability to set defaultless network device MAC addresses to deterministic computed locally administered values Andy Green
2012-07-05 2:44 ` Andy Green
2012-07-05 2:44 ` [PATCH 4 1/4] OMAP: add cpu id register to MAC address helper Andy Green
2012-07-05 2:44 ` Andy Green
2012-07-05 2:44 ` [PATCH 4 2/4] NET ethernet introduce mac_platform helper Andy Green
2012-07-05 2:44 ` Andy Green
2012-07-05 3:12 ` Joe Perches
2012-07-05 3:12 ` Joe Perches
2012-07-05 3:20 ` Andy Green
2012-07-05 3:20 ` Andy Green
2012-07-05 3:25 ` Joe Perches
2012-07-05 3:25 ` Joe Perches
2012-07-06 22:40 ` Ben Hutchings
2012-07-06 22:40 ` Ben Hutchings
2012-07-06 22:40 ` Ben Hutchings
2012-07-05 2:44 ` [PATCH 4 3/4] OMAP4 PANDA register ethernet and wlan for automatic mac allocation Andy Green
2012-07-05 2:44 ` Andy Green
2012-07-05 2:45 ` Andy Green [this message]
2012-07-05 2:45 ` [PATCH 4 4/4] config test config extending omap2plus with wl12xx etc Andy Green
2012-07-10 12:37 ` [PATCH 4 0/4] Add ability to set defaultless network device MAC addresses to deterministic computed locally administered values Florian Fainelli
2012-07-10 12:37 ` Florian Fainelli
2012-07-10 12:58 ` "Andy Green (林安廸)"
2012-07-10 12:58 ` "Andy Green (林安廸)"
2012-07-10 13:08 ` Steven Rostedt
2012-07-10 13:08 ` Steven Rostedt
2012-07-10 15:20 ` Alan Cox
2012-07-10 15:20 ` Alan Cox
2012-07-27 7:26 ` arm interrupt handling Qipeng Zha
2012-07-27 7:26 ` Qipeng Zha
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20120705024501.26317.53085.stgit@build.warmcat.com \
--to=andy.green@linaro.org \
--cc=arnd@arndb.de \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-omap@vger.kernel.org \
--cc=netdev@vger.kernel.org \
--cc=patches@linaro.org \
--cc=rostedt@goodmis.org \
--cc=s-jan@ti.com \
--cc=tony@atomide.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.