From: Nishanth Menon <nm@ti.com>
To: Tony Lindgren <tony@atomide.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>,
Kishon Vijay Abraham I <kishon@ti.com>,
<linux-omap@vger.kernel.org>, <linux-kernel@vger.kernel.org>,
<linux-arm-kernel@lists.infradead.org>,
<devicetree@vger.kernel.org>, Nishanth Menon <nm@ti.com>
Subject: [PATCH 1/2] ARM: dts: am57xx-beagle-x15: Remove pinmux configurations
Date: Fri, 2 Sep 2016 04:05:59 -0500 [thread overview]
Message-ID: <20160902090600.27262-2-nm@ti.com> (raw)
In-Reply-To: <20160902090600.27262-1-nm@ti.com>
pinmuxing for DRA7x/AM57x family of processors need to be done in IO
isolation as part of initial bootloader executed from SRAM. This is
done as part of iodelay configuration sequence and is required due to
the limitations introduced by erratum ID: i869[1] and elaborated in
the Technical Reference Manual[2] 18.4.6.1.7 Isolation Requirements.
Only peripheral that is permitted for dynamic pin mux configuration is
MMC. This is to accommodate the requirements for varied speeds (which
require IO-delay support in kernel as well). Hence with the exception
of MMC, all other pin mux configurations are removed from the dts.
[1] http://www.ti.com/lit/pdf/sprz429
[2] http://www.ti.com/lit/pdf/sprui30
Signed-off-by: Nishanth Menon <nm@ti.com>
---
arch/arm/boot/dts/am57xx-beagle-x15.dts | 222 +-------------------------------
1 file changed, 1 insertion(+), 221 deletions(-)
diff --git a/arch/arm/boot/dts/am57xx-beagle-x15.dts b/arch/arm/boot/dts/am57xx-beagle-x15.dts
index 9067ca092dc5..ef21da558ea3 100644
--- a/arch/arm/boot/dts/am57xx-beagle-x15.dts
+++ b/arch/arm/boot/dts/am57xx-beagle-x15.dts
@@ -59,8 +59,6 @@
leds {
compatible = "gpio-leds";
- pinctrl-names = "default";
- pinctrl-0 = <&leds_pins_default>;
led0 {
label = "beagle-x15:usr0";
@@ -116,9 +114,6 @@
tpd12s015: encoder {
compatible = "ti,tpd12s015";
- pinctrl-names = "default";
- pinctrl-0 = <&tpd12s015_pins>;
-
gpios = <&gpio7 10 GPIO_ACTIVE_HIGH>, /* gpio7_10, CT CP HPD */
<&gpio6 28 GPIO_ACTIVE_HIGH>, /* gpio6_28, LS OE */
<&gpio7 12 GPIO_ACTIVE_HIGH>; /* gpio7_12/sp1_cs2, HPD */
@@ -173,43 +168,6 @@
};
&dra7_pmx_core {
- leds_pins_default: leds_pins_default {
- pinctrl-single,pins = <
- DRA7XX_CORE_IOPAD(0x37a8, PIN_OUTPUT | MUX_MODE14) /* spi1_d1.gpio7_8 */
- DRA7XX_CORE_IOPAD(0x37ac, PIN_OUTPUT | MUX_MODE14) /* spi1_d0.gpio7_9 */
- DRA7XX_CORE_IOPAD(0x37c0, PIN_OUTPUT | MUX_MODE14) /* spi2_sclk.gpio7_14 */
- DRA7XX_CORE_IOPAD(0x37c4, PIN_OUTPUT | MUX_MODE14) /* spi2_d1.gpio7_15 */
- >;
- };
-
- i2c1_pins_default: i2c1_pins_default {
- pinctrl-single,pins = <
- DRA7XX_CORE_IOPAD(0x3800, PIN_INPUT_PULLUP | MUX_MODE0) /* i2c1_sda.sda */
- DRA7XX_CORE_IOPAD(0x3804, PIN_INPUT_PULLUP | MUX_MODE0) /* i2c1_scl.scl */
- >;
- };
-
- hdmi_pins: pinmux_hdmi_pins {
- pinctrl-single,pins = <
- DRA7XX_CORE_IOPAD(0x3808, PIN_INPUT | MUX_MODE1) /* i2c2_sda.hdmi1_ddc_scl */
- DRA7XX_CORE_IOPAD(0x380c, PIN_INPUT | MUX_MODE1) /* i2c2_scl.hdmi1_ddc_sda */
- >;
- };
-
- i2c3_pins_default: i2c3_pins_default {
- pinctrl-single,pins = <
- DRA7XX_CORE_IOPAD(0x36a4, PIN_INPUT| MUX_MODE10) /* mcasp1_aclkx.i2c3_sda */
- DRA7XX_CORE_IOPAD(0x36a8, PIN_INPUT| MUX_MODE10) /* mcasp1_fsx.i2c3_scl */
- >;
- };
-
- uart3_pins_default: uart3_pins_default {
- pinctrl-single,pins = <
- DRA7XX_CORE_IOPAD(0x37f8, PIN_INPUT_SLEW | MUX_MODE2) /* uart2_ctsn.uart3_rxd */
- DRA7XX_CORE_IOPAD(0x37fc, PIN_INPUT_SLEW | MUX_MODE1) /* uart2_rtsn.uart3_txd */
- >;
- };
-
mmc1_pins_default: mmc1_pins_default {
pinctrl-single,pins = <
DRA7XX_CORE_IOPAD(0x376c, PIN_INPUT | MUX_MODE14) /* mmc1sdcd.gpio219 */
@@ -236,154 +194,9 @@
DRA7XX_CORE_IOPAD(0x3498, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a22.mmc2_dat7 */
>;
};
-
- cpsw_pins_default: cpsw_pins_default {
- pinctrl-single,pins = <
- /* Slave 1 */
- DRA7XX_CORE_IOPAD(0x3650, PIN_OUTPUT | MUX_MODE0) /* rgmii1_tclk */
- DRA7XX_CORE_IOPAD(0x3654, PIN_OUTPUT | MUX_MODE0) /* rgmii1_tctl */
- DRA7XX_CORE_IOPAD(0x3658, PIN_OUTPUT | MUX_MODE0) /* rgmii1_td3 */
- DRA7XX_CORE_IOPAD(0x365c, PIN_OUTPUT | MUX_MODE0) /* rgmii1_td2 */
- DRA7XX_CORE_IOPAD(0x3660, PIN_OUTPUT | MUX_MODE0) /* rgmii1_td1 */
- DRA7XX_CORE_IOPAD(0x3664, PIN_OUTPUT | MUX_MODE0) /* rgmii1_td0 */
- DRA7XX_CORE_IOPAD(0x3668, PIN_INPUT | MUX_MODE0) /* rgmii1_rclk */
- DRA7XX_CORE_IOPAD(0x366c, PIN_INPUT | MUX_MODE0) /* rgmii1_rctl */
- DRA7XX_CORE_IOPAD(0x3670, PIN_INPUT | MUX_MODE0) /* rgmii1_rd3 */
- DRA7XX_CORE_IOPAD(0x3674, PIN_INPUT | MUX_MODE0) /* rgmii1_rd2 */
- DRA7XX_CORE_IOPAD(0x3678, PIN_INPUT | MUX_MODE0) /* rgmii1_rd1 */
- DRA7XX_CORE_IOPAD(0x367c, PIN_INPUT | MUX_MODE0) /* rgmii1_rd0 */
-
- /* Slave 2 */
- DRA7XX_CORE_IOPAD(0x3598, PIN_OUTPUT | MUX_MODE3) /* rgmii2_tclk */
- DRA7XX_CORE_IOPAD(0x359c, PIN_OUTPUT | MUX_MODE3) /* rgmii2_tctl */
- DRA7XX_CORE_IOPAD(0x35a0, PIN_OUTPUT | MUX_MODE3) /* rgmii2_td3 */
- DRA7XX_CORE_IOPAD(0x35a4, PIN_OUTPUT | MUX_MODE3) /* rgmii2_td2 */
- DRA7XX_CORE_IOPAD(0x35a8, PIN_OUTPUT | MUX_MODE3) /* rgmii2_td1 */
- DRA7XX_CORE_IOPAD(0x35ac, PIN_OUTPUT | MUX_MODE3) /* rgmii2_td0 */
- DRA7XX_CORE_IOPAD(0x35b0, PIN_INPUT | MUX_MODE3) /* rgmii2_rclk */
- DRA7XX_CORE_IOPAD(0x35b4, PIN_INPUT | MUX_MODE3) /* rgmii2_rctl */
- DRA7XX_CORE_IOPAD(0x35b8, PIN_INPUT | MUX_MODE3) /* rgmii2_rd3 */
- DRA7XX_CORE_IOPAD(0x35bc, PIN_INPUT | MUX_MODE3) /* rgmii2_rd2 */
- DRA7XX_CORE_IOPAD(0x35c0, PIN_INPUT | MUX_MODE3) /* rgmii2_rd1 */
- DRA7XX_CORE_IOPAD(0x35c4, PIN_INPUT | MUX_MODE3) /* rgmii2_rd0 */
- >;
-
- };
-
- cpsw_pins_sleep: cpsw_pins_sleep {
- pinctrl-single,pins = <
- /* Slave 1 */
- DRA7XX_CORE_IOPAD(0x3650, PIN_INPUT | MUX_MODE15)
- DRA7XX_CORE_IOPAD(0x3654, PIN_INPUT | MUX_MODE15)
- DRA7XX_CORE_IOPAD(0x3658, PIN_INPUT | MUX_MODE15)
- DRA7XX_CORE_IOPAD(0x365c, PIN_INPUT | MUX_MODE15)
- DRA7XX_CORE_IOPAD(0x3660, PIN_INPUT | MUX_MODE15)
- DRA7XX_CORE_IOPAD(0x3664, PIN_INPUT | MUX_MODE15)
- DRA7XX_CORE_IOPAD(0x3668, PIN_INPUT | MUX_MODE15)
- DRA7XX_CORE_IOPAD(0x366c, PIN_INPUT | MUX_MODE15)
- DRA7XX_CORE_IOPAD(0x3670, PIN_INPUT | MUX_MODE15)
- DRA7XX_CORE_IOPAD(0x3674, PIN_INPUT | MUX_MODE15)
- DRA7XX_CORE_IOPAD(0x3678, PIN_INPUT | MUX_MODE15)
- DRA7XX_CORE_IOPAD(0x367c, PIN_INPUT | MUX_MODE15)
-
- /* Slave 2 */
- DRA7XX_CORE_IOPAD(0x3598, PIN_INPUT | MUX_MODE15)
- DRA7XX_CORE_IOPAD(0x359c, PIN_INPUT | MUX_MODE15)
- DRA7XX_CORE_IOPAD(0x35a0, PIN_INPUT | MUX_MODE15)
- DRA7XX_CORE_IOPAD(0x35a4, PIN_INPUT | MUX_MODE15)
- DRA7XX_CORE_IOPAD(0x35a8, PIN_INPUT | MUX_MODE15)
- DRA7XX_CORE_IOPAD(0x35ac, PIN_INPUT | MUX_MODE15)
- DRA7XX_CORE_IOPAD(0x35b0, PIN_INPUT | MUX_MODE15)
- DRA7XX_CORE_IOPAD(0x35b4, PIN_INPUT | MUX_MODE15)
- DRA7XX_CORE_IOPAD(0x35b8, PIN_INPUT | MUX_MODE15)
- DRA7XX_CORE_IOPAD(0x35bc, PIN_INPUT | MUX_MODE15)
- DRA7XX_CORE_IOPAD(0x35c0, PIN_INPUT | MUX_MODE15)
- DRA7XX_CORE_IOPAD(0x35c4, PIN_INPUT | MUX_MODE15)
- >;
- };
-
- davinci_mdio_pins_default: davinci_mdio_pins_default {
- pinctrl-single,pins = <
- /* MDIO */
- DRA7XX_CORE_IOPAD(0x363c, PIN_OUTPUT_PULLUP | MUX_MODE0) /* mdio_mclk */
- DRA7XX_CORE_IOPAD(0x3640, PIN_INPUT_PULLUP | MUX_MODE0) /* mdio_d */
- >;
- };
-
- davinci_mdio_pins_sleep: davinci_mdio_pins_sleep {
- pinctrl-single,pins = <
- DRA7XX_CORE_IOPAD(0x363c, PIN_INPUT | MUX_MODE15)
- DRA7XX_CORE_IOPAD(0x3640, PIN_INPUT | MUX_MODE15)
- >;
- };
-
- tps659038_pins_default: tps659038_pins_default {
- pinctrl-single,pins = <
- DRA7XX_CORE_IOPAD(0x3818, PIN_INPUT_PULLUP | MUX_MODE14) /* wakeup0.gpio1_0 */
- >;
- };
-
- tmp102_pins_default: tmp102_pins_default {
- pinctrl-single,pins = <
- DRA7XX_CORE_IOPAD(0x37c8, PIN_INPUT_PULLUP | MUX_MODE14) /* spi2_d0.gpio7_16 */
- >;
- };
-
- mcp79410_pins_default: mcp79410_pins_default {
- pinctrl-single,pins = <
- DRA7XX_CORE_IOPAD(0x3824, PIN_INPUT_PULLUP | MUX_MODE1) /* wakeup3.sys_nirq1 */
- >;
- };
-
- usb1_pins: pinmux_usb1_pins {
- pinctrl-single,pins = <
- DRA7XX_CORE_IOPAD(0x3680, PIN_INPUT_SLEW | MUX_MODE0) /* usb1_drvvbus */
- >;
- };
-
- tpd12s015_pins: pinmux_tpd12s015_pins {
- pinctrl-single,pins = <
- DRA7XX_CORE_IOPAD(0x37b0, PIN_OUTPUT | MUX_MODE14) /* gpio7_10 CT_CP_HPD */
- DRA7XX_CORE_IOPAD(0x37b8, PIN_INPUT_PULLDOWN | MUX_MODE14) /* gpio7_12 HPD */
- DRA7XX_CORE_IOPAD(0x3770, PIN_OUTPUT | MUX_MODE14) /* gpio6_28 LS_OE */
- >;
- };
-
- clkout2_pins_default: clkout2_pins_default {
- pinctrl-single,pins = <
- DRA7XX_CORE_IOPAD(0x3694, PIN_OUTPUT_PULLDOWN | MUX_MODE9) /* xref_clk0.clkout2 */
- >;
- };
-
- clkout2_pins_sleep: clkout2_pins_sleep {
- pinctrl-single,pins = <
- DRA7XX_CORE_IOPAD(0x3694, PIN_INPUT | MUX_MODE15) /* xref_clk0.clkout2 */
- >;
- };
-
- mcasp3_pins_default: mcasp3_pins_default {
- pinctrl-single,pins = <
- DRA7XX_CORE_IOPAD(0x3724, PIN_INPUT_PULLDOWN | MUX_MODE0) /* mcasp3_aclkx.mcasp3_aclkx */
- DRA7XX_CORE_IOPAD(0x3728, PIN_INPUT_PULLDOWN | MUX_MODE0) /* mcasp3_fsx.mcasp3_fsx */
- DRA7XX_CORE_IOPAD(0x372c, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* mcasp3_axr0.mcasp3_axr0 */
- DRA7XX_CORE_IOPAD(0x3730, PIN_INPUT_PULLDOWN | MUX_MODE0) /* mcasp3_axr1.mcasp3_axr1 */
- >;
- };
-
- mcasp3_pins_sleep: mcasp3_pins_sleep {
- pinctrl-single,pins = <
- DRA7XX_CORE_IOPAD(0x3724, PIN_INPUT | MUX_MODE15)
- DRA7XX_CORE_IOPAD(0x3728, PIN_INPUT | MUX_MODE15)
- DRA7XX_CORE_IOPAD(0x372c, PIN_INPUT | MUX_MODE15)
- DRA7XX_CORE_IOPAD(0x3730, PIN_INPUT | MUX_MODE15)
- >;
- };
};
-
&i2c1 {
status = "okay";
- pinctrl-names = "default";
- pinctrl-0 = <&i2c1_pins_default>;
clock-frequency = <400000>;
tps659038: tps659038@58 {
@@ -392,9 +205,6 @@
interrupt-parent = <&gpio1>;
interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
- pinctrl-names = "default";
- pinctrl-0 = <&tps659038_pins_default>;
-
#interrupt-cells = <2>;
interrupt-controller;
@@ -556,8 +366,6 @@
tmp102: tmp102@48 {
compatible = "ti,tmp102";
reg = <0x48>;
- pinctrl-names = "default";
- pinctrl-0 = <&tmp102_pins_default>;
interrupt-parent = <&gpio7>;
interrupts = <16 IRQ_TYPE_LEVEL_LOW>;
#thermal-sensor-cells = <1>;
@@ -567,9 +375,6 @@
#sound-dai-cells = <0>;
compatible = "ti,tlv320aic3104";
reg = <0x18>;
- pinctrl-names = "default", "sleep";
- pinctrl-0 = <&clkout2_pins_default>;
- pinctrl-1 = <&clkout2_pins_sleep>;
assigned-clocks = <&clkoutmux2_clk_mux>;
assigned-clock-parents = <&sys_clk2_dclk_div>;
@@ -590,8 +395,6 @@
&i2c3 {
status = "okay";
- pinctrl-names = "default";
- pinctrl-0 = <&i2c3_pins_default>;
clock-frequency = <400000>;
mcp_rtc: rtc@6f {
@@ -601,9 +404,6 @@
<&dra7_pmx_core 0x424>;
interrupt-names = "irq", "wakeup";
- pinctrl-names = "default";
- pinctrl-0 = <&mcp79410_pins_default>;
-
vcc-supply = <&vdd_3v3>;
wakeup-source;
};
@@ -623,16 +423,10 @@
status = "okay";
interrupts-extended = <&crossbar_mpu GIC_SPI 69 IRQ_TYPE_LEVEL_HIGH>,
<&dra7_pmx_core 0x3f8>;
-
- pinctrl-names = "default";
- pinctrl-0 = <&uart3_pins_default>;
};
&mac {
status = "okay";
- pinctrl-names = "default", "sleep";
- pinctrl-0 = <&cpsw_pins_default>;
- pinctrl-1 = <&cpsw_pins_sleep>;
dual_emac;
};
@@ -648,12 +442,6 @@
dual_emac_res_vlan = <2>;
};
-&davinci_mdio {
- pinctrl-names = "default", "sleep";
- pinctrl-0 = <&davinci_mdio_pins_default>;
- pinctrl-1 = <&davinci_mdio_pins_sleep>;
-};
-
&mmc1 {
status = "okay";
@@ -669,7 +457,7 @@
status = "okay";
pinctrl-names = "default";
- pinctrl-0 = <&mmc2_pins_default>;
+ pinctrl-0 = <&mmc1_pins_default>;
vmmc-supply = <&vdd_3v3>;
bus-width = <8>;
@@ -691,8 +479,6 @@
&usb1 {
dr_mode = "host";
- pinctrl-names = "default";
- pinctrl-0 = <&usb1_pins>;
};
&omap_dwc3_2 {
@@ -768,9 +554,6 @@
status = "ok";
vdda-supply = <&ldo4_reg>;
- pinctrl-names = "default";
- pinctrl-0 = <&hdmi_pins>;
-
port {
hdmi_out: endpoint {
remote-endpoint = <&tpd12s015_in>;
@@ -784,9 +567,6 @@
&mcasp3 {
#sound-dai-cells = <0>;
- pinctrl-names = "default", "sleep";
- pinctrl-0 = <&mcasp3_pins_default>;
- pinctrl-1 = <&mcasp3_pins_sleep>;
assigned-clocks = <&mcasp3_ahclkx_mux>;
assigned-clock-parents = <&sys_clkin2>;
status = "okay";
--
2.9.1.200.gb1ec08f
WARNING: multiple messages have this Message-ID (diff)
From: Nishanth Menon <nm@ti.com>
To: Tony Lindgren <tony@atomide.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>,
Kishon Vijay Abraham I <kishon@ti.com>,
linux-omap@vger.kernel.org, linux-kernel@vger.kernel.org,
linux-arm-kernel@lists.infradead.org, devicetree@vger.kernel.org,
Nishanth Menon <nm@ti.com>
Subject: [PATCH 1/2] ARM: dts: am57xx-beagle-x15: Remove pinmux configurations
Date: Fri, 2 Sep 2016 04:05:59 -0500 [thread overview]
Message-ID: <20160902090600.27262-2-nm@ti.com> (raw)
In-Reply-To: <20160902090600.27262-1-nm@ti.com>
pinmuxing for DRA7x/AM57x family of processors need to be done in IO
isolation as part of initial bootloader executed from SRAM. This is
done as part of iodelay configuration sequence and is required due to
the limitations introduced by erratum ID: i869[1] and elaborated in
the Technical Reference Manual[2] 18.4.6.1.7 Isolation Requirements.
Only peripheral that is permitted for dynamic pin mux configuration is
MMC. This is to accommodate the requirements for varied speeds (which
require IO-delay support in kernel as well). Hence with the exception
of MMC, all other pin mux configurations are removed from the dts.
[1] http://www.ti.com/lit/pdf/sprz429
[2] http://www.ti.com/lit/pdf/sprui30
Signed-off-by: Nishanth Menon <nm@ti.com>
---
arch/arm/boot/dts/am57xx-beagle-x15.dts | 222 +-------------------------------
1 file changed, 1 insertion(+), 221 deletions(-)
diff --git a/arch/arm/boot/dts/am57xx-beagle-x15.dts b/arch/arm/boot/dts/am57xx-beagle-x15.dts
index 9067ca092dc5..ef21da558ea3 100644
--- a/arch/arm/boot/dts/am57xx-beagle-x15.dts
+++ b/arch/arm/boot/dts/am57xx-beagle-x15.dts
@@ -59,8 +59,6 @@
leds {
compatible = "gpio-leds";
- pinctrl-names = "default";
- pinctrl-0 = <&leds_pins_default>;
led0 {
label = "beagle-x15:usr0";
@@ -116,9 +114,6 @@
tpd12s015: encoder {
compatible = "ti,tpd12s015";
- pinctrl-names = "default";
- pinctrl-0 = <&tpd12s015_pins>;
-
gpios = <&gpio7 10 GPIO_ACTIVE_HIGH>, /* gpio7_10, CT CP HPD */
<&gpio6 28 GPIO_ACTIVE_HIGH>, /* gpio6_28, LS OE */
<&gpio7 12 GPIO_ACTIVE_HIGH>; /* gpio7_12/sp1_cs2, HPD */
@@ -173,43 +168,6 @@
};
&dra7_pmx_core {
- leds_pins_default: leds_pins_default {
- pinctrl-single,pins = <
- DRA7XX_CORE_IOPAD(0x37a8, PIN_OUTPUT | MUX_MODE14) /* spi1_d1.gpio7_8 */
- DRA7XX_CORE_IOPAD(0x37ac, PIN_OUTPUT | MUX_MODE14) /* spi1_d0.gpio7_9 */
- DRA7XX_CORE_IOPAD(0x37c0, PIN_OUTPUT | MUX_MODE14) /* spi2_sclk.gpio7_14 */
- DRA7XX_CORE_IOPAD(0x37c4, PIN_OUTPUT | MUX_MODE14) /* spi2_d1.gpio7_15 */
- >;
- };
-
- i2c1_pins_default: i2c1_pins_default {
- pinctrl-single,pins = <
- DRA7XX_CORE_IOPAD(0x3800, PIN_INPUT_PULLUP | MUX_MODE0) /* i2c1_sda.sda */
- DRA7XX_CORE_IOPAD(0x3804, PIN_INPUT_PULLUP | MUX_MODE0) /* i2c1_scl.scl */
- >;
- };
-
- hdmi_pins: pinmux_hdmi_pins {
- pinctrl-single,pins = <
- DRA7XX_CORE_IOPAD(0x3808, PIN_INPUT | MUX_MODE1) /* i2c2_sda.hdmi1_ddc_scl */
- DRA7XX_CORE_IOPAD(0x380c, PIN_INPUT | MUX_MODE1) /* i2c2_scl.hdmi1_ddc_sda */
- >;
- };
-
- i2c3_pins_default: i2c3_pins_default {
- pinctrl-single,pins = <
- DRA7XX_CORE_IOPAD(0x36a4, PIN_INPUT| MUX_MODE10) /* mcasp1_aclkx.i2c3_sda */
- DRA7XX_CORE_IOPAD(0x36a8, PIN_INPUT| MUX_MODE10) /* mcasp1_fsx.i2c3_scl */
- >;
- };
-
- uart3_pins_default: uart3_pins_default {
- pinctrl-single,pins = <
- DRA7XX_CORE_IOPAD(0x37f8, PIN_INPUT_SLEW | MUX_MODE2) /* uart2_ctsn.uart3_rxd */
- DRA7XX_CORE_IOPAD(0x37fc, PIN_INPUT_SLEW | MUX_MODE1) /* uart2_rtsn.uart3_txd */
- >;
- };
-
mmc1_pins_default: mmc1_pins_default {
pinctrl-single,pins = <
DRA7XX_CORE_IOPAD(0x376c, PIN_INPUT | MUX_MODE14) /* mmc1sdcd.gpio219 */
@@ -236,154 +194,9 @@
DRA7XX_CORE_IOPAD(0x3498, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a22.mmc2_dat7 */
>;
};
-
- cpsw_pins_default: cpsw_pins_default {
- pinctrl-single,pins = <
- /* Slave 1 */
- DRA7XX_CORE_IOPAD(0x3650, PIN_OUTPUT | MUX_MODE0) /* rgmii1_tclk */
- DRA7XX_CORE_IOPAD(0x3654, PIN_OUTPUT | MUX_MODE0) /* rgmii1_tctl */
- DRA7XX_CORE_IOPAD(0x3658, PIN_OUTPUT | MUX_MODE0) /* rgmii1_td3 */
- DRA7XX_CORE_IOPAD(0x365c, PIN_OUTPUT | MUX_MODE0) /* rgmii1_td2 */
- DRA7XX_CORE_IOPAD(0x3660, PIN_OUTPUT | MUX_MODE0) /* rgmii1_td1 */
- DRA7XX_CORE_IOPAD(0x3664, PIN_OUTPUT | MUX_MODE0) /* rgmii1_td0 */
- DRA7XX_CORE_IOPAD(0x3668, PIN_INPUT | MUX_MODE0) /* rgmii1_rclk */
- DRA7XX_CORE_IOPAD(0x366c, PIN_INPUT | MUX_MODE0) /* rgmii1_rctl */
- DRA7XX_CORE_IOPAD(0x3670, PIN_INPUT | MUX_MODE0) /* rgmii1_rd3 */
- DRA7XX_CORE_IOPAD(0x3674, PIN_INPUT | MUX_MODE0) /* rgmii1_rd2 */
- DRA7XX_CORE_IOPAD(0x3678, PIN_INPUT | MUX_MODE0) /* rgmii1_rd1 */
- DRA7XX_CORE_IOPAD(0x367c, PIN_INPUT | MUX_MODE0) /* rgmii1_rd0 */
-
- /* Slave 2 */
- DRA7XX_CORE_IOPAD(0x3598, PIN_OUTPUT | MUX_MODE3) /* rgmii2_tclk */
- DRA7XX_CORE_IOPAD(0x359c, PIN_OUTPUT | MUX_MODE3) /* rgmii2_tctl */
- DRA7XX_CORE_IOPAD(0x35a0, PIN_OUTPUT | MUX_MODE3) /* rgmii2_td3 */
- DRA7XX_CORE_IOPAD(0x35a4, PIN_OUTPUT | MUX_MODE3) /* rgmii2_td2 */
- DRA7XX_CORE_IOPAD(0x35a8, PIN_OUTPUT | MUX_MODE3) /* rgmii2_td1 */
- DRA7XX_CORE_IOPAD(0x35ac, PIN_OUTPUT | MUX_MODE3) /* rgmii2_td0 */
- DRA7XX_CORE_IOPAD(0x35b0, PIN_INPUT | MUX_MODE3) /* rgmii2_rclk */
- DRA7XX_CORE_IOPAD(0x35b4, PIN_INPUT | MUX_MODE3) /* rgmii2_rctl */
- DRA7XX_CORE_IOPAD(0x35b8, PIN_INPUT | MUX_MODE3) /* rgmii2_rd3 */
- DRA7XX_CORE_IOPAD(0x35bc, PIN_INPUT | MUX_MODE3) /* rgmii2_rd2 */
- DRA7XX_CORE_IOPAD(0x35c0, PIN_INPUT | MUX_MODE3) /* rgmii2_rd1 */
- DRA7XX_CORE_IOPAD(0x35c4, PIN_INPUT | MUX_MODE3) /* rgmii2_rd0 */
- >;
-
- };
-
- cpsw_pins_sleep: cpsw_pins_sleep {
- pinctrl-single,pins = <
- /* Slave 1 */
- DRA7XX_CORE_IOPAD(0x3650, PIN_INPUT | MUX_MODE15)
- DRA7XX_CORE_IOPAD(0x3654, PIN_INPUT | MUX_MODE15)
- DRA7XX_CORE_IOPAD(0x3658, PIN_INPUT | MUX_MODE15)
- DRA7XX_CORE_IOPAD(0x365c, PIN_INPUT | MUX_MODE15)
- DRA7XX_CORE_IOPAD(0x3660, PIN_INPUT | MUX_MODE15)
- DRA7XX_CORE_IOPAD(0x3664, PIN_INPUT | MUX_MODE15)
- DRA7XX_CORE_IOPAD(0x3668, PIN_INPUT | MUX_MODE15)
- DRA7XX_CORE_IOPAD(0x366c, PIN_INPUT | MUX_MODE15)
- DRA7XX_CORE_IOPAD(0x3670, PIN_INPUT | MUX_MODE15)
- DRA7XX_CORE_IOPAD(0x3674, PIN_INPUT | MUX_MODE15)
- DRA7XX_CORE_IOPAD(0x3678, PIN_INPUT | MUX_MODE15)
- DRA7XX_CORE_IOPAD(0x367c, PIN_INPUT | MUX_MODE15)
-
- /* Slave 2 */
- DRA7XX_CORE_IOPAD(0x3598, PIN_INPUT | MUX_MODE15)
- DRA7XX_CORE_IOPAD(0x359c, PIN_INPUT | MUX_MODE15)
- DRA7XX_CORE_IOPAD(0x35a0, PIN_INPUT | MUX_MODE15)
- DRA7XX_CORE_IOPAD(0x35a4, PIN_INPUT | MUX_MODE15)
- DRA7XX_CORE_IOPAD(0x35a8, PIN_INPUT | MUX_MODE15)
- DRA7XX_CORE_IOPAD(0x35ac, PIN_INPUT | MUX_MODE15)
- DRA7XX_CORE_IOPAD(0x35b0, PIN_INPUT | MUX_MODE15)
- DRA7XX_CORE_IOPAD(0x35b4, PIN_INPUT | MUX_MODE15)
- DRA7XX_CORE_IOPAD(0x35b8, PIN_INPUT | MUX_MODE15)
- DRA7XX_CORE_IOPAD(0x35bc, PIN_INPUT | MUX_MODE15)
- DRA7XX_CORE_IOPAD(0x35c0, PIN_INPUT | MUX_MODE15)
- DRA7XX_CORE_IOPAD(0x35c4, PIN_INPUT | MUX_MODE15)
- >;
- };
-
- davinci_mdio_pins_default: davinci_mdio_pins_default {
- pinctrl-single,pins = <
- /* MDIO */
- DRA7XX_CORE_IOPAD(0x363c, PIN_OUTPUT_PULLUP | MUX_MODE0) /* mdio_mclk */
- DRA7XX_CORE_IOPAD(0x3640, PIN_INPUT_PULLUP | MUX_MODE0) /* mdio_d */
- >;
- };
-
- davinci_mdio_pins_sleep: davinci_mdio_pins_sleep {
- pinctrl-single,pins = <
- DRA7XX_CORE_IOPAD(0x363c, PIN_INPUT | MUX_MODE15)
- DRA7XX_CORE_IOPAD(0x3640, PIN_INPUT | MUX_MODE15)
- >;
- };
-
- tps659038_pins_default: tps659038_pins_default {
- pinctrl-single,pins = <
- DRA7XX_CORE_IOPAD(0x3818, PIN_INPUT_PULLUP | MUX_MODE14) /* wakeup0.gpio1_0 */
- >;
- };
-
- tmp102_pins_default: tmp102_pins_default {
- pinctrl-single,pins = <
- DRA7XX_CORE_IOPAD(0x37c8, PIN_INPUT_PULLUP | MUX_MODE14) /* spi2_d0.gpio7_16 */
- >;
- };
-
- mcp79410_pins_default: mcp79410_pins_default {
- pinctrl-single,pins = <
- DRA7XX_CORE_IOPAD(0x3824, PIN_INPUT_PULLUP | MUX_MODE1) /* wakeup3.sys_nirq1 */
- >;
- };
-
- usb1_pins: pinmux_usb1_pins {
- pinctrl-single,pins = <
- DRA7XX_CORE_IOPAD(0x3680, PIN_INPUT_SLEW | MUX_MODE0) /* usb1_drvvbus */
- >;
- };
-
- tpd12s015_pins: pinmux_tpd12s015_pins {
- pinctrl-single,pins = <
- DRA7XX_CORE_IOPAD(0x37b0, PIN_OUTPUT | MUX_MODE14) /* gpio7_10 CT_CP_HPD */
- DRA7XX_CORE_IOPAD(0x37b8, PIN_INPUT_PULLDOWN | MUX_MODE14) /* gpio7_12 HPD */
- DRA7XX_CORE_IOPAD(0x3770, PIN_OUTPUT | MUX_MODE14) /* gpio6_28 LS_OE */
- >;
- };
-
- clkout2_pins_default: clkout2_pins_default {
- pinctrl-single,pins = <
- DRA7XX_CORE_IOPAD(0x3694, PIN_OUTPUT_PULLDOWN | MUX_MODE9) /* xref_clk0.clkout2 */
- >;
- };
-
- clkout2_pins_sleep: clkout2_pins_sleep {
- pinctrl-single,pins = <
- DRA7XX_CORE_IOPAD(0x3694, PIN_INPUT | MUX_MODE15) /* xref_clk0.clkout2 */
- >;
- };
-
- mcasp3_pins_default: mcasp3_pins_default {
- pinctrl-single,pins = <
- DRA7XX_CORE_IOPAD(0x3724, PIN_INPUT_PULLDOWN | MUX_MODE0) /* mcasp3_aclkx.mcasp3_aclkx */
- DRA7XX_CORE_IOPAD(0x3728, PIN_INPUT_PULLDOWN | MUX_MODE0) /* mcasp3_fsx.mcasp3_fsx */
- DRA7XX_CORE_IOPAD(0x372c, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* mcasp3_axr0.mcasp3_axr0 */
- DRA7XX_CORE_IOPAD(0x3730, PIN_INPUT_PULLDOWN | MUX_MODE0) /* mcasp3_axr1.mcasp3_axr1 */
- >;
- };
-
- mcasp3_pins_sleep: mcasp3_pins_sleep {
- pinctrl-single,pins = <
- DRA7XX_CORE_IOPAD(0x3724, PIN_INPUT | MUX_MODE15)
- DRA7XX_CORE_IOPAD(0x3728, PIN_INPUT | MUX_MODE15)
- DRA7XX_CORE_IOPAD(0x372c, PIN_INPUT | MUX_MODE15)
- DRA7XX_CORE_IOPAD(0x3730, PIN_INPUT | MUX_MODE15)
- >;
- };
};
-
&i2c1 {
status = "okay";
- pinctrl-names = "default";
- pinctrl-0 = <&i2c1_pins_default>;
clock-frequency = <400000>;
tps659038: tps659038@58 {
@@ -392,9 +205,6 @@
interrupt-parent = <&gpio1>;
interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
- pinctrl-names = "default";
- pinctrl-0 = <&tps659038_pins_default>;
-
#interrupt-cells = <2>;
interrupt-controller;
@@ -556,8 +366,6 @@
tmp102: tmp102@48 {
compatible = "ti,tmp102";
reg = <0x48>;
- pinctrl-names = "default";
- pinctrl-0 = <&tmp102_pins_default>;
interrupt-parent = <&gpio7>;
interrupts = <16 IRQ_TYPE_LEVEL_LOW>;
#thermal-sensor-cells = <1>;
@@ -567,9 +375,6 @@
#sound-dai-cells = <0>;
compatible = "ti,tlv320aic3104";
reg = <0x18>;
- pinctrl-names = "default", "sleep";
- pinctrl-0 = <&clkout2_pins_default>;
- pinctrl-1 = <&clkout2_pins_sleep>;
assigned-clocks = <&clkoutmux2_clk_mux>;
assigned-clock-parents = <&sys_clk2_dclk_div>;
@@ -590,8 +395,6 @@
&i2c3 {
status = "okay";
- pinctrl-names = "default";
- pinctrl-0 = <&i2c3_pins_default>;
clock-frequency = <400000>;
mcp_rtc: rtc@6f {
@@ -601,9 +404,6 @@
<&dra7_pmx_core 0x424>;
interrupt-names = "irq", "wakeup";
- pinctrl-names = "default";
- pinctrl-0 = <&mcp79410_pins_default>;
-
vcc-supply = <&vdd_3v3>;
wakeup-source;
};
@@ -623,16 +423,10 @@
status = "okay";
interrupts-extended = <&crossbar_mpu GIC_SPI 69 IRQ_TYPE_LEVEL_HIGH>,
<&dra7_pmx_core 0x3f8>;
-
- pinctrl-names = "default";
- pinctrl-0 = <&uart3_pins_default>;
};
&mac {
status = "okay";
- pinctrl-names = "default", "sleep";
- pinctrl-0 = <&cpsw_pins_default>;
- pinctrl-1 = <&cpsw_pins_sleep>;
dual_emac;
};
@@ -648,12 +442,6 @@
dual_emac_res_vlan = <2>;
};
-&davinci_mdio {
- pinctrl-names = "default", "sleep";
- pinctrl-0 = <&davinci_mdio_pins_default>;
- pinctrl-1 = <&davinci_mdio_pins_sleep>;
-};
-
&mmc1 {
status = "okay";
@@ -669,7 +457,7 @@
status = "okay";
pinctrl-names = "default";
- pinctrl-0 = <&mmc2_pins_default>;
+ pinctrl-0 = <&mmc1_pins_default>;
vmmc-supply = <&vdd_3v3>;
bus-width = <8>;
@@ -691,8 +479,6 @@
&usb1 {
dr_mode = "host";
- pinctrl-names = "default";
- pinctrl-0 = <&usb1_pins>;
};
&omap_dwc3_2 {
@@ -768,9 +554,6 @@
status = "ok";
vdda-supply = <&ldo4_reg>;
- pinctrl-names = "default";
- pinctrl-0 = <&hdmi_pins>;
-
port {
hdmi_out: endpoint {
remote-endpoint = <&tpd12s015_in>;
@@ -784,9 +567,6 @@
&mcasp3 {
#sound-dai-cells = <0>;
- pinctrl-names = "default", "sleep";
- pinctrl-0 = <&mcasp3_pins_default>;
- pinctrl-1 = <&mcasp3_pins_sleep>;
assigned-clocks = <&mcasp3_ahclkx_mux>;
assigned-clock-parents = <&sys_clkin2>;
status = "okay";
--
2.9.1.200.gb1ec08f
WARNING: multiple messages have this Message-ID (diff)
From: nm@ti.com (Nishanth Menon)
To: linux-arm-kernel@lists.infradead.org
Subject: [PATCH 1/2] ARM: dts: am57xx-beagle-x15: Remove pinmux configurations
Date: Fri, 2 Sep 2016 04:05:59 -0500 [thread overview]
Message-ID: <20160902090600.27262-2-nm@ti.com> (raw)
In-Reply-To: <20160902090600.27262-1-nm@ti.com>
pinmuxing for DRA7x/AM57x family of processors need to be done in IO
isolation as part of initial bootloader executed from SRAM. This is
done as part of iodelay configuration sequence and is required due to
the limitations introduced by erratum ID: i869[1] and elaborated in
the Technical Reference Manual[2] 18.4.6.1.7 Isolation Requirements.
Only peripheral that is permitted for dynamic pin mux configuration is
MMC. This is to accommodate the requirements for varied speeds (which
require IO-delay support in kernel as well). Hence with the exception
of MMC, all other pin mux configurations are removed from the dts.
[1] http://www.ti.com/lit/pdf/sprz429
[2] http://www.ti.com/lit/pdf/sprui30
Signed-off-by: Nishanth Menon <nm@ti.com>
---
arch/arm/boot/dts/am57xx-beagle-x15.dts | 222 +-------------------------------
1 file changed, 1 insertion(+), 221 deletions(-)
diff --git a/arch/arm/boot/dts/am57xx-beagle-x15.dts b/arch/arm/boot/dts/am57xx-beagle-x15.dts
index 9067ca092dc5..ef21da558ea3 100644
--- a/arch/arm/boot/dts/am57xx-beagle-x15.dts
+++ b/arch/arm/boot/dts/am57xx-beagle-x15.dts
@@ -59,8 +59,6 @@
leds {
compatible = "gpio-leds";
- pinctrl-names = "default";
- pinctrl-0 = <&leds_pins_default>;
led0 {
label = "beagle-x15:usr0";
@@ -116,9 +114,6 @@
tpd12s015: encoder {
compatible = "ti,tpd12s015";
- pinctrl-names = "default";
- pinctrl-0 = <&tpd12s015_pins>;
-
gpios = <&gpio7 10 GPIO_ACTIVE_HIGH>, /* gpio7_10, CT CP HPD */
<&gpio6 28 GPIO_ACTIVE_HIGH>, /* gpio6_28, LS OE */
<&gpio7 12 GPIO_ACTIVE_HIGH>; /* gpio7_12/sp1_cs2, HPD */
@@ -173,43 +168,6 @@
};
&dra7_pmx_core {
- leds_pins_default: leds_pins_default {
- pinctrl-single,pins = <
- DRA7XX_CORE_IOPAD(0x37a8, PIN_OUTPUT | MUX_MODE14) /* spi1_d1.gpio7_8 */
- DRA7XX_CORE_IOPAD(0x37ac, PIN_OUTPUT | MUX_MODE14) /* spi1_d0.gpio7_9 */
- DRA7XX_CORE_IOPAD(0x37c0, PIN_OUTPUT | MUX_MODE14) /* spi2_sclk.gpio7_14 */
- DRA7XX_CORE_IOPAD(0x37c4, PIN_OUTPUT | MUX_MODE14) /* spi2_d1.gpio7_15 */
- >;
- };
-
- i2c1_pins_default: i2c1_pins_default {
- pinctrl-single,pins = <
- DRA7XX_CORE_IOPAD(0x3800, PIN_INPUT_PULLUP | MUX_MODE0) /* i2c1_sda.sda */
- DRA7XX_CORE_IOPAD(0x3804, PIN_INPUT_PULLUP | MUX_MODE0) /* i2c1_scl.scl */
- >;
- };
-
- hdmi_pins: pinmux_hdmi_pins {
- pinctrl-single,pins = <
- DRA7XX_CORE_IOPAD(0x3808, PIN_INPUT | MUX_MODE1) /* i2c2_sda.hdmi1_ddc_scl */
- DRA7XX_CORE_IOPAD(0x380c, PIN_INPUT | MUX_MODE1) /* i2c2_scl.hdmi1_ddc_sda */
- >;
- };
-
- i2c3_pins_default: i2c3_pins_default {
- pinctrl-single,pins = <
- DRA7XX_CORE_IOPAD(0x36a4, PIN_INPUT| MUX_MODE10) /* mcasp1_aclkx.i2c3_sda */
- DRA7XX_CORE_IOPAD(0x36a8, PIN_INPUT| MUX_MODE10) /* mcasp1_fsx.i2c3_scl */
- >;
- };
-
- uart3_pins_default: uart3_pins_default {
- pinctrl-single,pins = <
- DRA7XX_CORE_IOPAD(0x37f8, PIN_INPUT_SLEW | MUX_MODE2) /* uart2_ctsn.uart3_rxd */
- DRA7XX_CORE_IOPAD(0x37fc, PIN_INPUT_SLEW | MUX_MODE1) /* uart2_rtsn.uart3_txd */
- >;
- };
-
mmc1_pins_default: mmc1_pins_default {
pinctrl-single,pins = <
DRA7XX_CORE_IOPAD(0x376c, PIN_INPUT | MUX_MODE14) /* mmc1sdcd.gpio219 */
@@ -236,154 +194,9 @@
DRA7XX_CORE_IOPAD(0x3498, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a22.mmc2_dat7 */
>;
};
-
- cpsw_pins_default: cpsw_pins_default {
- pinctrl-single,pins = <
- /* Slave 1 */
- DRA7XX_CORE_IOPAD(0x3650, PIN_OUTPUT | MUX_MODE0) /* rgmii1_tclk */
- DRA7XX_CORE_IOPAD(0x3654, PIN_OUTPUT | MUX_MODE0) /* rgmii1_tctl */
- DRA7XX_CORE_IOPAD(0x3658, PIN_OUTPUT | MUX_MODE0) /* rgmii1_td3 */
- DRA7XX_CORE_IOPAD(0x365c, PIN_OUTPUT | MUX_MODE0) /* rgmii1_td2 */
- DRA7XX_CORE_IOPAD(0x3660, PIN_OUTPUT | MUX_MODE0) /* rgmii1_td1 */
- DRA7XX_CORE_IOPAD(0x3664, PIN_OUTPUT | MUX_MODE0) /* rgmii1_td0 */
- DRA7XX_CORE_IOPAD(0x3668, PIN_INPUT | MUX_MODE0) /* rgmii1_rclk */
- DRA7XX_CORE_IOPAD(0x366c, PIN_INPUT | MUX_MODE0) /* rgmii1_rctl */
- DRA7XX_CORE_IOPAD(0x3670, PIN_INPUT | MUX_MODE0) /* rgmii1_rd3 */
- DRA7XX_CORE_IOPAD(0x3674, PIN_INPUT | MUX_MODE0) /* rgmii1_rd2 */
- DRA7XX_CORE_IOPAD(0x3678, PIN_INPUT | MUX_MODE0) /* rgmii1_rd1 */
- DRA7XX_CORE_IOPAD(0x367c, PIN_INPUT | MUX_MODE0) /* rgmii1_rd0 */
-
- /* Slave 2 */
- DRA7XX_CORE_IOPAD(0x3598, PIN_OUTPUT | MUX_MODE3) /* rgmii2_tclk */
- DRA7XX_CORE_IOPAD(0x359c, PIN_OUTPUT | MUX_MODE3) /* rgmii2_tctl */
- DRA7XX_CORE_IOPAD(0x35a0, PIN_OUTPUT | MUX_MODE3) /* rgmii2_td3 */
- DRA7XX_CORE_IOPAD(0x35a4, PIN_OUTPUT | MUX_MODE3) /* rgmii2_td2 */
- DRA7XX_CORE_IOPAD(0x35a8, PIN_OUTPUT | MUX_MODE3) /* rgmii2_td1 */
- DRA7XX_CORE_IOPAD(0x35ac, PIN_OUTPUT | MUX_MODE3) /* rgmii2_td0 */
- DRA7XX_CORE_IOPAD(0x35b0, PIN_INPUT | MUX_MODE3) /* rgmii2_rclk */
- DRA7XX_CORE_IOPAD(0x35b4, PIN_INPUT | MUX_MODE3) /* rgmii2_rctl */
- DRA7XX_CORE_IOPAD(0x35b8, PIN_INPUT | MUX_MODE3) /* rgmii2_rd3 */
- DRA7XX_CORE_IOPAD(0x35bc, PIN_INPUT | MUX_MODE3) /* rgmii2_rd2 */
- DRA7XX_CORE_IOPAD(0x35c0, PIN_INPUT | MUX_MODE3) /* rgmii2_rd1 */
- DRA7XX_CORE_IOPAD(0x35c4, PIN_INPUT | MUX_MODE3) /* rgmii2_rd0 */
- >;
-
- };
-
- cpsw_pins_sleep: cpsw_pins_sleep {
- pinctrl-single,pins = <
- /* Slave 1 */
- DRA7XX_CORE_IOPAD(0x3650, PIN_INPUT | MUX_MODE15)
- DRA7XX_CORE_IOPAD(0x3654, PIN_INPUT | MUX_MODE15)
- DRA7XX_CORE_IOPAD(0x3658, PIN_INPUT | MUX_MODE15)
- DRA7XX_CORE_IOPAD(0x365c, PIN_INPUT | MUX_MODE15)
- DRA7XX_CORE_IOPAD(0x3660, PIN_INPUT | MUX_MODE15)
- DRA7XX_CORE_IOPAD(0x3664, PIN_INPUT | MUX_MODE15)
- DRA7XX_CORE_IOPAD(0x3668, PIN_INPUT | MUX_MODE15)
- DRA7XX_CORE_IOPAD(0x366c, PIN_INPUT | MUX_MODE15)
- DRA7XX_CORE_IOPAD(0x3670, PIN_INPUT | MUX_MODE15)
- DRA7XX_CORE_IOPAD(0x3674, PIN_INPUT | MUX_MODE15)
- DRA7XX_CORE_IOPAD(0x3678, PIN_INPUT | MUX_MODE15)
- DRA7XX_CORE_IOPAD(0x367c, PIN_INPUT | MUX_MODE15)
-
- /* Slave 2 */
- DRA7XX_CORE_IOPAD(0x3598, PIN_INPUT | MUX_MODE15)
- DRA7XX_CORE_IOPAD(0x359c, PIN_INPUT | MUX_MODE15)
- DRA7XX_CORE_IOPAD(0x35a0, PIN_INPUT | MUX_MODE15)
- DRA7XX_CORE_IOPAD(0x35a4, PIN_INPUT | MUX_MODE15)
- DRA7XX_CORE_IOPAD(0x35a8, PIN_INPUT | MUX_MODE15)
- DRA7XX_CORE_IOPAD(0x35ac, PIN_INPUT | MUX_MODE15)
- DRA7XX_CORE_IOPAD(0x35b0, PIN_INPUT | MUX_MODE15)
- DRA7XX_CORE_IOPAD(0x35b4, PIN_INPUT | MUX_MODE15)
- DRA7XX_CORE_IOPAD(0x35b8, PIN_INPUT | MUX_MODE15)
- DRA7XX_CORE_IOPAD(0x35bc, PIN_INPUT | MUX_MODE15)
- DRA7XX_CORE_IOPAD(0x35c0, PIN_INPUT | MUX_MODE15)
- DRA7XX_CORE_IOPAD(0x35c4, PIN_INPUT | MUX_MODE15)
- >;
- };
-
- davinci_mdio_pins_default: davinci_mdio_pins_default {
- pinctrl-single,pins = <
- /* MDIO */
- DRA7XX_CORE_IOPAD(0x363c, PIN_OUTPUT_PULLUP | MUX_MODE0) /* mdio_mclk */
- DRA7XX_CORE_IOPAD(0x3640, PIN_INPUT_PULLUP | MUX_MODE0) /* mdio_d */
- >;
- };
-
- davinci_mdio_pins_sleep: davinci_mdio_pins_sleep {
- pinctrl-single,pins = <
- DRA7XX_CORE_IOPAD(0x363c, PIN_INPUT | MUX_MODE15)
- DRA7XX_CORE_IOPAD(0x3640, PIN_INPUT | MUX_MODE15)
- >;
- };
-
- tps659038_pins_default: tps659038_pins_default {
- pinctrl-single,pins = <
- DRA7XX_CORE_IOPAD(0x3818, PIN_INPUT_PULLUP | MUX_MODE14) /* wakeup0.gpio1_0 */
- >;
- };
-
- tmp102_pins_default: tmp102_pins_default {
- pinctrl-single,pins = <
- DRA7XX_CORE_IOPAD(0x37c8, PIN_INPUT_PULLUP | MUX_MODE14) /* spi2_d0.gpio7_16 */
- >;
- };
-
- mcp79410_pins_default: mcp79410_pins_default {
- pinctrl-single,pins = <
- DRA7XX_CORE_IOPAD(0x3824, PIN_INPUT_PULLUP | MUX_MODE1) /* wakeup3.sys_nirq1 */
- >;
- };
-
- usb1_pins: pinmux_usb1_pins {
- pinctrl-single,pins = <
- DRA7XX_CORE_IOPAD(0x3680, PIN_INPUT_SLEW | MUX_MODE0) /* usb1_drvvbus */
- >;
- };
-
- tpd12s015_pins: pinmux_tpd12s015_pins {
- pinctrl-single,pins = <
- DRA7XX_CORE_IOPAD(0x37b0, PIN_OUTPUT | MUX_MODE14) /* gpio7_10 CT_CP_HPD */
- DRA7XX_CORE_IOPAD(0x37b8, PIN_INPUT_PULLDOWN | MUX_MODE14) /* gpio7_12 HPD */
- DRA7XX_CORE_IOPAD(0x3770, PIN_OUTPUT | MUX_MODE14) /* gpio6_28 LS_OE */
- >;
- };
-
- clkout2_pins_default: clkout2_pins_default {
- pinctrl-single,pins = <
- DRA7XX_CORE_IOPAD(0x3694, PIN_OUTPUT_PULLDOWN | MUX_MODE9) /* xref_clk0.clkout2 */
- >;
- };
-
- clkout2_pins_sleep: clkout2_pins_sleep {
- pinctrl-single,pins = <
- DRA7XX_CORE_IOPAD(0x3694, PIN_INPUT | MUX_MODE15) /* xref_clk0.clkout2 */
- >;
- };
-
- mcasp3_pins_default: mcasp3_pins_default {
- pinctrl-single,pins = <
- DRA7XX_CORE_IOPAD(0x3724, PIN_INPUT_PULLDOWN | MUX_MODE0) /* mcasp3_aclkx.mcasp3_aclkx */
- DRA7XX_CORE_IOPAD(0x3728, PIN_INPUT_PULLDOWN | MUX_MODE0) /* mcasp3_fsx.mcasp3_fsx */
- DRA7XX_CORE_IOPAD(0x372c, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* mcasp3_axr0.mcasp3_axr0 */
- DRA7XX_CORE_IOPAD(0x3730, PIN_INPUT_PULLDOWN | MUX_MODE0) /* mcasp3_axr1.mcasp3_axr1 */
- >;
- };
-
- mcasp3_pins_sleep: mcasp3_pins_sleep {
- pinctrl-single,pins = <
- DRA7XX_CORE_IOPAD(0x3724, PIN_INPUT | MUX_MODE15)
- DRA7XX_CORE_IOPAD(0x3728, PIN_INPUT | MUX_MODE15)
- DRA7XX_CORE_IOPAD(0x372c, PIN_INPUT | MUX_MODE15)
- DRA7XX_CORE_IOPAD(0x3730, PIN_INPUT | MUX_MODE15)
- >;
- };
};
-
&i2c1 {
status = "okay";
- pinctrl-names = "default";
- pinctrl-0 = <&i2c1_pins_default>;
clock-frequency = <400000>;
tps659038: tps659038 at 58 {
@@ -392,9 +205,6 @@
interrupt-parent = <&gpio1>;
interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
- pinctrl-names = "default";
- pinctrl-0 = <&tps659038_pins_default>;
-
#interrupt-cells = <2>;
interrupt-controller;
@@ -556,8 +366,6 @@
tmp102: tmp102 at 48 {
compatible = "ti,tmp102";
reg = <0x48>;
- pinctrl-names = "default";
- pinctrl-0 = <&tmp102_pins_default>;
interrupt-parent = <&gpio7>;
interrupts = <16 IRQ_TYPE_LEVEL_LOW>;
#thermal-sensor-cells = <1>;
@@ -567,9 +375,6 @@
#sound-dai-cells = <0>;
compatible = "ti,tlv320aic3104";
reg = <0x18>;
- pinctrl-names = "default", "sleep";
- pinctrl-0 = <&clkout2_pins_default>;
- pinctrl-1 = <&clkout2_pins_sleep>;
assigned-clocks = <&clkoutmux2_clk_mux>;
assigned-clock-parents = <&sys_clk2_dclk_div>;
@@ -590,8 +395,6 @@
&i2c3 {
status = "okay";
- pinctrl-names = "default";
- pinctrl-0 = <&i2c3_pins_default>;
clock-frequency = <400000>;
mcp_rtc: rtc at 6f {
@@ -601,9 +404,6 @@
<&dra7_pmx_core 0x424>;
interrupt-names = "irq", "wakeup";
- pinctrl-names = "default";
- pinctrl-0 = <&mcp79410_pins_default>;
-
vcc-supply = <&vdd_3v3>;
wakeup-source;
};
@@ -623,16 +423,10 @@
status = "okay";
interrupts-extended = <&crossbar_mpu GIC_SPI 69 IRQ_TYPE_LEVEL_HIGH>,
<&dra7_pmx_core 0x3f8>;
-
- pinctrl-names = "default";
- pinctrl-0 = <&uart3_pins_default>;
};
&mac {
status = "okay";
- pinctrl-names = "default", "sleep";
- pinctrl-0 = <&cpsw_pins_default>;
- pinctrl-1 = <&cpsw_pins_sleep>;
dual_emac;
};
@@ -648,12 +442,6 @@
dual_emac_res_vlan = <2>;
};
-&davinci_mdio {
- pinctrl-names = "default", "sleep";
- pinctrl-0 = <&davinci_mdio_pins_default>;
- pinctrl-1 = <&davinci_mdio_pins_sleep>;
-};
-
&mmc1 {
status = "okay";
@@ -669,7 +457,7 @@
status = "okay";
pinctrl-names = "default";
- pinctrl-0 = <&mmc2_pins_default>;
+ pinctrl-0 = <&mmc1_pins_default>;
vmmc-supply = <&vdd_3v3>;
bus-width = <8>;
@@ -691,8 +479,6 @@
&usb1 {
dr_mode = "host";
- pinctrl-names = "default";
- pinctrl-0 = <&usb1_pins>;
};
&omap_dwc3_2 {
@@ -768,9 +554,6 @@
status = "ok";
vdda-supply = <&ldo4_reg>;
- pinctrl-names = "default";
- pinctrl-0 = <&hdmi_pins>;
-
port {
hdmi_out: endpoint {
remote-endpoint = <&tpd12s015_in>;
@@ -784,9 +567,6 @@
&mcasp3 {
#sound-dai-cells = <0>;
- pinctrl-names = "default", "sleep";
- pinctrl-0 = <&mcasp3_pins_default>;
- pinctrl-1 = <&mcasp3_pins_sleep>;
assigned-clocks = <&mcasp3_ahclkx_mux>;
assigned-clock-parents = <&sys_clkin2>;
status = "okay";
--
2.9.1.200.gb1ec08f
next prev parent reply other threads:[~2016-09-02 9:06 UTC|newest]
Thread overview: 51+ messages / expand[flat|nested] mbox.gz Atom feed top
2016-09-02 9:05 [PATCH 0/2] ARM: dts: Introduce support for rev BeagleBoard-X15 B1 Nishanth Menon
2016-09-02 9:05 ` Nishanth Menon
2016-09-02 9:05 ` Nishanth Menon
2016-09-02 9:05 ` Nishanth Menon [this message]
2016-09-02 9:05 ` [PATCH 1/2] ARM: dts: am57xx-beagle-x15: Remove pinmux configurations Nishanth Menon
2016-09-02 9:05 ` Nishanth Menon
2016-09-02 10:18 ` Sekhar Nori
2016-09-02 10:18 ` Sekhar Nori
2016-09-02 10:18 ` Sekhar Nori
2016-09-02 14:52 ` Nishanth Menon
2016-09-02 14:52 ` Nishanth Menon
2016-09-02 14:52 ` Nishanth Menon
2016-09-02 9:06 ` [PATCH 2/2] ARM: dts: am57xx-beagle-x15: Add support for rev B1 Nishanth Menon
2016-09-02 9:06 ` Nishanth Menon
2016-09-02 9:06 ` Nishanth Menon
2016-09-02 9:58 ` Tomi Valkeinen
2016-09-02 9:58 ` Tomi Valkeinen
2016-09-02 9:58 ` Tomi Valkeinen
2016-09-02 10:01 ` Nishanth Menon
2016-09-02 10:01 ` Nishanth Menon
2016-09-02 10:01 ` Nishanth Menon
2016-09-02 11:48 ` Tomi Valkeinen
2016-09-02 11:48 ` Tomi Valkeinen
2016-09-02 11:48 ` Tomi Valkeinen
2016-09-02 10:41 ` Sekhar Nori
2016-09-02 10:41 ` Sekhar Nori
2016-09-02 10:41 ` Sekhar Nori
2016-09-02 11:18 ` Tomi Valkeinen
2016-09-02 11:18 ` Tomi Valkeinen
2016-09-02 11:18 ` Tomi Valkeinen
2016-09-02 13:52 ` Robert Nelson
2016-09-02 13:52 ` Robert Nelson
2016-09-02 13:52 ` Robert Nelson
2016-09-02 15:01 ` Nishanth Menon
2016-09-02 15:01 ` Nishanth Menon
2016-09-02 15:01 ` Nishanth Menon
2016-09-02 15:06 ` Tony Lindgren
2016-09-02 15:06 ` Tony Lindgren
2016-09-02 15:06 ` Tony Lindgren
2016-09-06 10:10 ` Sekhar Nori
2016-09-06 10:10 ` Sekhar Nori
2016-09-06 10:10 ` Sekhar Nori
2016-09-06 20:05 ` Tony Lindgren
2016-09-06 20:05 ` Tony Lindgren
2016-09-06 20:05 ` Tony Lindgren
2016-09-07 5:09 ` Sekhar Nori
2016-09-07 5:09 ` Sekhar Nori
2016-09-07 5:09 ` Sekhar Nori
2016-09-02 9:14 ` [PATCH 0/2] ARM: dts: Introduce support for rev BeagleBoard-X15 B1 Nishanth Menon
2016-09-02 9:14 ` Nishanth Menon
2016-09-02 9:14 ` Nishanth Menon
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20160902090600.27262-2-nm@ti.com \
--to=nm@ti.com \
--cc=devicetree@vger.kernel.org \
--cc=kishon@ti.com \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-omap@vger.kernel.org \
--cc=tomi.valkeinen@ti.com \
--cc=tony@atomide.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.