All of lore.kernel.org
 help / color / mirror / Atom feed
From: Eric Anholt <eric@anholt.net>
To: Florian Fainelli <f.fainelli@gmail.com>,
	Michael Turquette <mturquette@baylibre.com>,
	Stephen Boyd <sboyd@codeaurora.org>,
	Rob Herring <robh+dt@kernel.org>,
	Mark Rutland <mark.rutland@arm.com>,
	dri-devel@lists.freedesktop.org,
	Thierry Reding <thierry.reding@gmail.com>
Cc: linux-rpi-kernel@lists.infradead.org,
	linux-arm-kernel@lists.infradead.org,
	linux-kernel@vger.kernel.org,
	Stephen Warren <swarren@wwwdotorg.org>,
	Lee Jones <lee@kernel.org>,
	bcm-kernel-feedback-list@broadcom.com, linux-clk@vger.kernel.org,
	Eric Anholt <eric@anholt.net>
Subject: [PATCH 11/11] ARM: bcm2835: Enable the Raspberry Pi touchscreen panel.
Date: Wed, 14 Dec 2016 11:46:21 -0800	[thread overview]
Message-ID: <20161214194621.16499-12-eric@anholt.net> (raw)
In-Reply-To: <20161214194621.16499-1-eric@anholt.net>

This commit is not intended to be merged.  Instead we will use
overlays to enable the panel, and this commit is just a demo of how
things get wired up.

Signed-off-by: Eric Anholt <eric@anholt.net>
---
 arch/arm/boot/dts/bcm283x.dtsi | 30 +++++++++++++++++++++++++++++-
 1 file changed, 29 insertions(+), 1 deletion(-)

diff --git a/arch/arm/boot/dts/bcm283x.dtsi b/arch/arm/boot/dts/bcm283x.dtsi
index 82a4eccfb3d8..e96d0f29759a 100644
--- a/arch/arm/boot/dts/bcm283x.dtsi
+++ b/arch/arm/boot/dts/bcm283x.dtsi
@@ -286,7 +286,12 @@
 					     "dsi1_ddr2",
 					     "dsi1_ddr";
 
-			status = "disabled";
+			pitouchscreen: panel@0 {
+				compatible = "raspberrypi,touchscreen";
+				reg = <0>;
+
+				raspberrypi,touchscreen-bridge = <&pitouchscreen_bridge>;
+			};
 		};
 
 		i2c1: i2c@7e804000 {
@@ -346,6 +351,29 @@
 		vc4: gpu {
 			compatible = "brcm,bcm2835-vc4";
 		};
+
+		i2c_dsi: i2c {
+			/* We have to use i2c-gpio because the
+			 * firmware is also polling another device
+			 * using the only hardware I2C bus that could
+			 * connect to these pins.
+			 */
+			compatible = "i2c-gpio";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			gpios = <&gpio 28 0
+				 &gpio 29 0>;
+
+			pitouchscreen_bridge: bridge@45 {
+				compatible = "raspberrypi,touchscreen-bridge-i2c";
+				reg = <0x45>;
+			};
+
+			pitouchscreen_touch: bridge@38 {
+				compatible = "raspberrypi,touchscreen-ts-i2c";
+				reg = <0x38>;
+			};
+		};
 	};
 
 	clocks {
-- 
2.11.0

WARNING: multiple messages have this Message-ID (diff)
From: eric@anholt.net (Eric Anholt)
To: linux-arm-kernel@lists.infradead.org
Subject: [PATCH 11/11] ARM: bcm2835: Enable the Raspberry Pi touchscreen panel.
Date: Wed, 14 Dec 2016 11:46:21 -0800	[thread overview]
Message-ID: <20161214194621.16499-12-eric@anholt.net> (raw)
In-Reply-To: <20161214194621.16499-1-eric@anholt.net>

This commit is not intended to be merged.  Instead we will use
overlays to enable the panel, and this commit is just a demo of how
things get wired up.

Signed-off-by: Eric Anholt <eric@anholt.net>
---
 arch/arm/boot/dts/bcm283x.dtsi | 30 +++++++++++++++++++++++++++++-
 1 file changed, 29 insertions(+), 1 deletion(-)

diff --git a/arch/arm/boot/dts/bcm283x.dtsi b/arch/arm/boot/dts/bcm283x.dtsi
index 82a4eccfb3d8..e96d0f29759a 100644
--- a/arch/arm/boot/dts/bcm283x.dtsi
+++ b/arch/arm/boot/dts/bcm283x.dtsi
@@ -286,7 +286,12 @@
 					     "dsi1_ddr2",
 					     "dsi1_ddr";
 
-			status = "disabled";
+			pitouchscreen: panel at 0 {
+				compatible = "raspberrypi,touchscreen";
+				reg = <0>;
+
+				raspberrypi,touchscreen-bridge = <&pitouchscreen_bridge>;
+			};
 		};
 
 		i2c1: i2c at 7e804000 {
@@ -346,6 +351,29 @@
 		vc4: gpu {
 			compatible = "brcm,bcm2835-vc4";
 		};
+
+		i2c_dsi: i2c {
+			/* We have to use i2c-gpio because the
+			 * firmware is also polling another device
+			 * using the only hardware I2C bus that could
+			 * connect to these pins.
+			 */
+			compatible = "i2c-gpio";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			gpios = <&gpio 28 0
+				 &gpio 29 0>;
+
+			pitouchscreen_bridge: bridge at 45 {
+				compatible = "raspberrypi,touchscreen-bridge-i2c";
+				reg = <0x45>;
+			};
+
+			pitouchscreen_touch: bridge at 38 {
+				compatible = "raspberrypi,touchscreen-ts-i2c";
+				reg = <0x38>;
+			};
+		};
 	};
 
 	clocks {
-- 
2.11.0

WARNING: multiple messages have this Message-ID (diff)
From: Eric Anholt <eric@anholt.net>
To: Florian Fainelli <f.fainelli@gmail.com>,
	Michael Turquette <mturquette@baylibre.com>,
	Stephen Boyd <sboyd@codeaurora.org>,
	Rob Herring <robh+dt@kernel.org>,
	Mark Rutland <mark.rutland@arm.com>,
	dri-devel@lists.freedesktop.org,
	Thierry Reding <thierry.reding@gmail.com>
Cc: Stephen Warren <swarren@wwwdotorg.org>,
	Lee Jones <lee@kernel.org>,
	linux-kernel@vger.kernel.org,
	bcm-kernel-feedback-list@broadcom.com,
	linux-rpi-kernel@lists.infradead.org, linux-clk@vger.kernel.org,
	linux-arm-kernel@lists.infradead.org
Subject: [PATCH 11/11] ARM: bcm2835: Enable the Raspberry Pi touchscreen panel.
Date: Wed, 14 Dec 2016 11:46:21 -0800	[thread overview]
Message-ID: <20161214194621.16499-12-eric@anholt.net> (raw)
In-Reply-To: <20161214194621.16499-1-eric@anholt.net>

This commit is not intended to be merged.  Instead we will use
overlays to enable the panel, and this commit is just a demo of how
things get wired up.

Signed-off-by: Eric Anholt <eric@anholt.net>
---
 arch/arm/boot/dts/bcm283x.dtsi | 30 +++++++++++++++++++++++++++++-
 1 file changed, 29 insertions(+), 1 deletion(-)

diff --git a/arch/arm/boot/dts/bcm283x.dtsi b/arch/arm/boot/dts/bcm283x.dtsi
index 82a4eccfb3d8..e96d0f29759a 100644
--- a/arch/arm/boot/dts/bcm283x.dtsi
+++ b/arch/arm/boot/dts/bcm283x.dtsi
@@ -286,7 +286,12 @@
 					     "dsi1_ddr2",
 					     "dsi1_ddr";
 
-			status = "disabled";
+			pitouchscreen: panel@0 {
+				compatible = "raspberrypi,touchscreen";
+				reg = <0>;
+
+				raspberrypi,touchscreen-bridge = <&pitouchscreen_bridge>;
+			};
 		};
 
 		i2c1: i2c@7e804000 {
@@ -346,6 +351,29 @@
 		vc4: gpu {
 			compatible = "brcm,bcm2835-vc4";
 		};
+
+		i2c_dsi: i2c {
+			/* We have to use i2c-gpio because the
+			 * firmware is also polling another device
+			 * using the only hardware I2C bus that could
+			 * connect to these pins.
+			 */
+			compatible = "i2c-gpio";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			gpios = <&gpio 28 0
+				 &gpio 29 0>;
+
+			pitouchscreen_bridge: bridge@45 {
+				compatible = "raspberrypi,touchscreen-bridge-i2c";
+				reg = <0x45>;
+			};
+
+			pitouchscreen_touch: bridge@38 {
+				compatible = "raspberrypi,touchscreen-ts-i2c";
+				reg = <0x38>;
+			};
+		};
 	};
 
 	clocks {
-- 
2.11.0

_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel

  parent reply	other threads:[~2016-12-14 19:48 UTC|newest]

Thread overview: 64+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2016-12-14 19:46 [PATCH 00/11] drm/vc4: DSI panel support + Raspberry Pi touchscreen Eric Anholt
2016-12-14 19:46 ` Eric Anholt
2016-12-14 19:46 ` [PATCH 01/11] clk: bcm2835: Don't rate change PLLs on behalf of DSI PLL dividers Eric Anholt
2016-12-14 19:46   ` Eric Anholt
2016-12-14 19:46   ` Eric Anholt
2016-12-14 19:46 ` [PATCH 02/11] clk: bcm2835: Register the DSI0/DSI1 pixel clocks Eric Anholt
2016-12-14 19:46   ` Eric Anholt
2016-12-14 19:46   ` Eric Anholt
2016-12-21 23:14   ` Stephen Boyd
2016-12-21 23:14     ` Stephen Boyd
2016-12-21 23:14     ` Stephen Boyd
2016-12-22  1:23     ` Eric Anholt
2016-12-22  1:23       ` Eric Anholt
2016-12-22  1:23       ` Eric Anholt
2016-12-14 19:46 ` [PATCH 03/11] clk: bcm2835: Add leaf clock measurement support, disabled by default Eric Anholt
2016-12-14 19:46   ` Eric Anholt
2016-12-14 19:46   ` Eric Anholt
2016-12-14 19:46 ` [PATCH 04/11] drm/vc4: Set up SCALER_DISPCTRL at boot Eric Anholt
2016-12-14 19:46   ` Eric Anholt
2017-01-31 19:35   ` Daniel Vetter
2017-01-31 19:35     ` Daniel Vetter
2017-01-31 19:35     ` Daniel Vetter
2016-12-14 19:46 ` [PATCH 05/11] drm/vc4: Add support for feeding DSI encoders from the pixel valve Eric Anholt
2016-12-14 19:46   ` Eric Anholt
2017-01-31 19:39   ` Daniel Vetter
2017-01-31 19:39     ` Daniel Vetter
2017-01-31 19:39     ` Daniel Vetter
2017-01-31 19:54     ` Eric Anholt
2017-01-31 19:54       ` Eric Anholt
2017-01-31 19:54       ` Eric Anholt
2016-12-14 19:46 ` [PATCH 06/11] dt-bindings: Document the VC4 DSI module nodes Eric Anholt
2016-12-14 19:46   ` Eric Anholt
2016-12-14 19:46   ` Eric Anholt
2016-12-14 19:46 ` [PATCH 07/11] drm/vc4: Add DSI driver Eric Anholt
2016-12-14 19:46   ` Eric Anholt
2016-12-14 19:46   ` Eric Anholt
2017-01-31 19:51   ` Daniel Vetter
2017-01-31 19:51     ` Daniel Vetter
2017-01-31 19:51     ` Daniel Vetter
2016-12-14 19:46 ` [PATCH 08/11] dt-bindings: Document the Raspberry Pi Touchscreen nodes Eric Anholt
2016-12-14 19:46   ` Eric Anholt
2016-12-14 19:46   ` Eric Anholt
2016-12-14 19:46 ` [PATCH 09/11] drm/panel: Add support for the Raspberry Pi 7" Touchscreen Eric Anholt
2016-12-14 19:46   ` Eric Anholt
2016-12-14 19:46   ` Eric Anholt
2017-01-31 21:07   ` Thierry Reding
2017-01-31 21:07     ` Thierry Reding
2017-01-31 21:07     ` Thierry Reding
2017-01-31 21:17     ` Daniel Vetter
2017-01-31 21:17       ` Daniel Vetter
2017-01-31 21:17       ` Daniel Vetter
2017-01-31 21:42       ` Thierry Reding
2017-01-31 21:42         ` Thierry Reding
2017-01-31 21:42         ` Thierry Reding
2017-01-31 21:19     ` Daniel Vetter
2017-01-31 21:19       ` Daniel Vetter
2017-01-31 21:19       ` Daniel Vetter
2017-01-31 21:38       ` Thierry Reding
2017-01-31 21:38         ` Thierry Reding
2016-12-14 19:46 ` [PATCH 10/11] ARM: bcm2835: dt: Add the DSI module nodes and clocks Eric Anholt
2016-12-14 19:46   ` Eric Anholt
2016-12-14 19:46 ` Eric Anholt [this message]
2016-12-14 19:46   ` [PATCH 11/11] ARM: bcm2835: Enable the Raspberry Pi touchscreen panel Eric Anholt
2016-12-14 19:46   ` Eric Anholt

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20161214194621.16499-12-eric@anholt.net \
    --to=eric@anholt.net \
    --cc=bcm-kernel-feedback-list@broadcom.com \
    --cc=dri-devel@lists.freedesktop.org \
    --cc=f.fainelli@gmail.com \
    --cc=lee@kernel.org \
    --cc=linux-arm-kernel@lists.infradead.org \
    --cc=linux-clk@vger.kernel.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=linux-rpi-kernel@lists.infradead.org \
    --cc=mark.rutland@arm.com \
    --cc=mturquette@baylibre.com \
    --cc=robh+dt@kernel.org \
    --cc=sboyd@codeaurora.org \
    --cc=swarren@wwwdotorg.org \
    --cc=thierry.reding@gmail.com \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body. 
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.