From: Jerome Brunet <jbrunet@baylibre.com>
To: Kevin Hilman <khilman@baylibre.com>, Carlo Caione <carlo@caione.org>
Cc: Jerome Brunet <jbrunet@baylibre.com>,
linux-amlogic@lists.infradead.org, devicetree@vger.kernel.org,
linux-arm-kernel@lists.infradead.org,
linux-kernel@vger.kernel.org
Subject: [PATCH v2 3/9] ARM64: dts: meson: add mmc clk gate pins
Date: Mon, 21 Aug 2017 18:06:31 +0200 [thread overview]
Message-ID: <20170821160637.22456-4-jbrunet@baylibre.com> (raw)
In-Reply-To: <20170821160637.22456-1-jbrunet@baylibre.com>
Add the pinctrl to switch mmc clk pins in gpio (pulled down) mode. This
is necessary to be able to gate the clk outside of the SoC while
keeping it running in the controller
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
---
.../arm64/boot/dts/amlogic/meson-gx-p23x-q20x.dtsi | 9 ++++--
.../boot/dts/amlogic/meson-gxbb-nanopi-k2.dts | 9 ++++--
.../boot/dts/amlogic/meson-gxbb-nexbox-a95x.dts | 11 +++++---
.../arm64/boot/dts/amlogic/meson-gxbb-odroidc2.dts | 8 ++++--
arch/arm64/boot/dts/amlogic/meson-gxbb-p20x.dtsi | 9 ++++--
.../boot/dts/amlogic/meson-gxbb-vega-s95.dtsi | 9 ++++--
arch/arm64/boot/dts/amlogic/meson-gxbb.dtsi | 33 ++++++++++++++++++++++
.../dts/amlogic/meson-gxl-s905x-hwacom-amazetv.dts | 6 ++--
.../dts/amlogic/meson-gxl-s905x-libretech-cc.dts | 6 ++--
.../dts/amlogic/meson-gxl-s905x-nexbox-a95x.dts | 9 ++++--
.../boot/dts/amlogic/meson-gxl-s905x-p212.dtsi | 9 ++++--
arch/arm64/boot/dts/amlogic/meson-gxl.dtsi | 33 ++++++++++++++++++++++
.../arm64/boot/dts/amlogic/meson-gxm-nexbox-a1.dts | 6 ++--
13 files changed, 126 insertions(+), 31 deletions(-)
diff --git a/arch/arm64/boot/dts/amlogic/meson-gx-p23x-q20x.dtsi b/arch/arm64/boot/dts/amlogic/meson-gx-p23x-q20x.dtsi
index cff39c5a2632..9ac904f75013 100644
--- a/arch/arm64/boot/dts/amlogic/meson-gx-p23x-q20x.dtsi
+++ b/arch/arm64/boot/dts/amlogic/meson-gx-p23x-q20x.dtsi
@@ -161,7 +161,8 @@
&sd_emmc_a {
status = "okay";
pinctrl-0 = <&sdio_pins>;
- pinctrl-names = "default";
+ pinctrl-1 = <&sdio_clk_gate_pins>;
+ pinctrl-names = "default", "clk-gate";
#address-cells = <1>;
#size-cells = <0>;
@@ -187,7 +188,8 @@
&sd_emmc_b {
status = "okay";
pinctrl-0 = <&sdcard_pins>;
- pinctrl-names = "default";
+ pinctrl-1 = <&sdcard_clk_gate_pins>;
+ pinctrl-names = "default", "clk-gate";
bus-width = <4>;
cap-sd-highspeed;
@@ -205,7 +207,8 @@
&sd_emmc_c {
status = "okay";
pinctrl-0 = <&emmc_pins>;
- pinctrl-names = "default";
+ pinctrl-1 = <&emmc_clk_gate_pins>;
+ pinctrl-names = "default", "clk-gate";
bus-width = <8>;
cap-mmc-highspeed;
diff --git a/arch/arm64/boot/dts/amlogic/meson-gxbb-nanopi-k2.dts b/arch/arm64/boot/dts/amlogic/meson-gxbb-nanopi-k2.dts
index b48a4576158a..e4c6b2fd52ee 100644
--- a/arch/arm64/boot/dts/amlogic/meson-gxbb-nanopi-k2.dts
+++ b/arch/arm64/boot/dts/amlogic/meson-gxbb-nanopi-k2.dts
@@ -192,7 +192,8 @@
&sd_emmc_a {
status = "okay";
pinctrl-0 = <&sdio_pins>, <&sdio_irq_pins>;
- pinctrl-names = "default";
+ pinctrl-1 = <&sdio_clk_gate_pins>;
+ pinctrl-names = "default", "clk-gate";
#address-cells = <1>;
#size-cells = <0>;
@@ -218,7 +219,8 @@
&sd_emmc_b {
status = "okay";
pinctrl-0 = <&sdcard_pins>;
- pinctrl-names = "default";
+ pinctrl-1 = <&sdcard_clk_gate_pins>;
+ pinctrl-names = "default", "clk-gate";
bus-width = <4>;
cap-sd-highspeed;
@@ -236,7 +238,8 @@
&sd_emmc_c {
status = "disabled";
pinctrl-0 = <&emmc_pins>;
- pinctrl-names = "default";
+ pinctrl-1 = <&emmc_clk_gate_pins>;
+ pinctrl-names = "default", "clk-gate";
bus-width = <8>;
max-frequency = <200000000>;
diff --git a/arch/arm64/boot/dts/amlogic/meson-gxbb-nexbox-a95x.dts b/arch/arm64/boot/dts/amlogic/meson-gxbb-nexbox-a95x.dts
index c64c2256d092..7342c31f73b6 100644
--- a/arch/arm64/boot/dts/amlogic/meson-gxbb-nexbox-a95x.dts
+++ b/arch/arm64/boot/dts/amlogic/meson-gxbb-nexbox-a95x.dts
@@ -51,7 +51,7 @@
/ {
compatible = "nexbox,a95x", "amlogic,meson-gxbb";
model = "NEXBOX A95X";
-
+
aliases {
serial0 = &uart_AO;
};
@@ -225,7 +225,8 @@
&sd_emmc_a {
status = "okay";
pinctrl-0 = <&sdio_pins>;
- pinctrl-names = "default";
+ pinctrl-1 = <&sdio_clk_gate_pins>;
+ pinctrl-names = "default", "clk-gate";
#address-cells = <1>;
#size-cells = <0>;
@@ -246,7 +247,8 @@
&sd_emmc_b {
status = "okay";
pinctrl-0 = <&sdcard_pins>;
- pinctrl-names = "default";
+ pinctrl-1 = <&sdcard_clk_gate_pins>;
+ pinctrl-names = "default", "clk-gate";
bus-width = <4>;
cap-sd-highspeed;
@@ -264,7 +266,8 @@
&sd_emmc_c {
status = "okay";
pinctrl-0 = <&emmc_pins>;
- pinctrl-names = "default";
+ pinctrl-1 = <&emmc_clk_gate_pins>;
+ pinctrl-names = "default", "clk-gate";
bus-width = <8>;
cap-mmc-highspeed;
diff --git a/arch/arm64/boot/dts/amlogic/meson-gxbb-odroidc2.dts b/arch/arm64/boot/dts/amlogic/meson-gxbb-odroidc2.dts
index a12303becab4..1ffa1c238a72 100644
--- a/arch/arm64/boot/dts/amlogic/meson-gxbb-odroidc2.dts
+++ b/arch/arm64/boot/dts/amlogic/meson-gxbb-odroidc2.dts
@@ -50,7 +50,7 @@
/ {
compatible = "hardkernel,odroid-c2", "amlogic,meson-gxbb";
model = "Hardkernel ODROID-C2";
-
+
aliases {
serial0 = &uart_AO;
};
@@ -253,7 +253,8 @@
&sd_emmc_b {
status = "okay";
pinctrl-0 = <&sdcard_pins>;
- pinctrl-names = "default";
+ pinctrl-1 = <&sdcard_clk_gate_pins>;
+ pinctrl-names = "default", "clk-gate";
bus-width = <4>;
cap-sd-highspeed;
@@ -271,7 +272,8 @@
&sd_emmc_c {
status = "okay";
pinctrl-0 = <&emmc_pins>;
- pinctrl-names = "default";
+ pinctrl-1 = <&emmc_clk_gate_pins>;
+ pinctrl-names = "default", "clk-gate";
bus-width = <8>;
max-frequency = <200000000>;
diff --git a/arch/arm64/boot/dts/amlogic/meson-gxbb-p20x.dtsi b/arch/arm64/boot/dts/amlogic/meson-gxbb-p20x.dtsi
index 30b880b694de..99c409d1c8f8 100644
--- a/arch/arm64/boot/dts/amlogic/meson-gxbb-p20x.dtsi
+++ b/arch/arm64/boot/dts/amlogic/meson-gxbb-p20x.dtsi
@@ -187,7 +187,8 @@
&sd_emmc_a {
status = "okay";
pinctrl-0 = <&sdio_pins>;
- pinctrl-names = "default";
+ pinctrl-1 = <&sdio_clk_gate_pins>;
+ pinctrl-names = "default", "clk-gate";
#address-cells = <1>;
#size-cells = <0>;
@@ -213,7 +214,8 @@
&sd_emmc_b {
status = "okay";
pinctrl-0 = <&sdcard_pins>;
- pinctrl-names = "default";
+ pinctrl-1 = <&sdcard_clk_gate_pins>;
+ pinctrl-names = "default", "clk-gate";
bus-width = <4>;
cap-sd-highspeed;
@@ -231,7 +233,8 @@
&sd_emmc_c {
status = "okay";
pinctrl-0 = <&emmc_pins>;
- pinctrl-names = "default";
+ pinctrl-1 = <&emmc_clk_gate_pins>;
+ pinctrl-names = "default", "clk-gate";
bus-width = <8>;
cap-mmc-highspeed;
diff --git a/arch/arm64/boot/dts/amlogic/meson-gxbb-vega-s95.dtsi b/arch/arm64/boot/dts/amlogic/meson-gxbb-vega-s95.dtsi
index 0262ef8d48e4..f2bc6dea1fc6 100644
--- a/arch/arm64/boot/dts/amlogic/meson-gxbb-vega-s95.dtsi
+++ b/arch/arm64/boot/dts/amlogic/meson-gxbb-vega-s95.dtsi
@@ -155,7 +155,8 @@
&sd_emmc_a {
status = "okay";
pinctrl-0 = <&sdio_pins &sdio_irq_pins>;
- pinctrl-names = "default";
+ pinctrl-1 = <&sdio_clk_gate_pins>;
+ pinctrl-names = "default", "clk-gate";
#address-cells = <1>;
#size-cells = <0>;
@@ -181,7 +182,8 @@
&sd_emmc_b {
status = "okay";
pinctrl-0 = <&sdcard_pins>;
- pinctrl-names = "default";
+ pinctrl-1 = <&sdcard_clk_gate_pins>;
+ pinctrl-names = "default", "clk-gate";
bus-width = <4>;
cap-sd-highspeed;
@@ -198,7 +200,8 @@
&sd_emmc_c {
status = "okay";
pinctrl-0 = <&emmc_pins>;
- pinctrl-names = "default";
+ pinctrl-1 = <&emmc_clk_gate_pins>;
+ pinctrl-names = "default", "clk-gate";
bus-width = <8>;
cap-mmc-highspeed;
diff --git a/arch/arm64/boot/dts/amlogic/meson-gxbb.dtsi b/arch/arm64/boot/dts/amlogic/meson-gxbb.dtsi
index 9a1e478f80d5..1d6314e2eb8a 100644
--- a/arch/arm64/boot/dts/amlogic/meson-gxbb.dtsi
+++ b/arch/arm64/boot/dts/amlogic/meson-gxbb.dtsi
@@ -383,6 +383,17 @@
};
};
+ emmc_clk_gate_pins: emmc_clk_gate {
+ mux {
+ groups = "BOOT_8";
+ function = "gpio_periphs";
+ };
+ cfg-pull-down {
+ pins = "BOOT_8";
+ bias-pull-down;
+ };
+ };
+
nor_pins: nor {
mux {
groups = "nor_d",
@@ -421,6 +432,17 @@
};
};
+ sdcard_clk_gate_pins: sdcard_clk_gate {
+ mux {
+ groups = "CARD_2";
+ function = "gpio_periphs";
+ };
+ cfg-pull-down {
+ pins = "CARD_2";
+ bias-pull-down;
+ };
+ };
+
sdio_pins: sdio {
mux {
groups = "sdio_d0",
@@ -433,6 +455,17 @@
};
};
+ sdio_clk_gate_pins: sdio_clk_gate {
+ mux {
+ groups = "GPIOX_4";
+ function = "gpio_periphs";
+ };
+ cfg-pull-down {
+ pins = "GPIOX_4";
+ bias-pull-down;
+ };
+ };
+
sdio_irq_pins: sdio_irq {
mux {
groups = "sdio_irq";
diff --git a/arch/arm64/boot/dts/amlogic/meson-gxl-s905x-hwacom-amazetv.dts b/arch/arm64/boot/dts/amlogic/meson-gxl-s905x-hwacom-amazetv.dts
index f779a985f923..977b4240f3c1 100644
--- a/arch/arm64/boot/dts/amlogic/meson-gxl-s905x-hwacom-amazetv.dts
+++ b/arch/arm64/boot/dts/amlogic/meson-gxl-s905x-hwacom-amazetv.dts
@@ -123,7 +123,8 @@
&sd_emmc_b {
status = "okay";
pinctrl-0 = <&sdcard_pins>;
- pinctrl-names = "default";
+ pinctrl-1 = <&sdcard_clk_gate_pins>;
+ pinctrl-names = "default", "clk-gate";
bus-width = <4>;
cap-sd-highspeed;
@@ -141,7 +142,8 @@
&sd_emmc_c {
status = "okay";
pinctrl-0 = <&emmc_pins>;
- pinctrl-names = "default";
+ pinctrl-1 = <&emmc_clk_gate_pins>;
+ pinctrl-names = "default", "clk-gate";
bus-width = <8>;
cap-mmc-highspeed;
diff --git a/arch/arm64/boot/dts/amlogic/meson-gxl-s905x-libretech-cc.dts b/arch/arm64/boot/dts/amlogic/meson-gxl-s905x-libretech-cc.dts
index 51c4ecc3b31e..2b56f7d9be2b 100644
--- a/arch/arm64/boot/dts/amlogic/meson-gxl-s905x-libretech-cc.dts
+++ b/arch/arm64/boot/dts/amlogic/meson-gxl-s905x-libretech-cc.dts
@@ -134,7 +134,8 @@
&sd_emmc_b {
status = "okay";
pinctrl-0 = <&sdcard_pins>;
- pinctrl-names = "default";
+ pinctrl-1 = <&sdcard_clk_gate_pins>;
+ pinctrl-names = "default", "clk-gate";
bus-width = <4>;
cap-sd-highspeed;
@@ -156,7 +157,8 @@
&sd_emmc_c {
status = "okay";
pinctrl-0 = <&emmc_pins>;
- pinctrl-names = "default";
+ pinctrl-1 = <&emmc_clk_gate_pins>;
+ pinctrl-names = "default", "clk-gate";
bus-width = <8>;
cap-mmc-highspeed;
diff --git a/arch/arm64/boot/dts/amlogic/meson-gxl-s905x-nexbox-a95x.dts b/arch/arm64/boot/dts/amlogic/meson-gxl-s905x-nexbox-a95x.dts
index 83c35efbae8b..df448b11a16b 100644
--- a/arch/arm64/boot/dts/amlogic/meson-gxl-s905x-nexbox-a95x.dts
+++ b/arch/arm64/boot/dts/amlogic/meson-gxl-s905x-nexbox-a95x.dts
@@ -182,7 +182,8 @@
&sd_emmc_a {
status = "okay";
pinctrl-0 = <&sdio_pins>;
- pinctrl-names = "default";
+ pinctrl-1 = <&sdio_clk_gate_pins>;
+ pinctrl-names = "default", "clk-gate";
#address-cells = <1>;
#size-cells = <0>;
@@ -203,7 +204,8 @@
&sd_emmc_b {
status = "okay";
pinctrl-0 = <&sdcard_pins>;
- pinctrl-names = "default";
+ pinctrl-1 = <&sdcard_clk_gate_pins>;
+ pinctrl-names = "default", "clk-gate";
bus-width = <4>;
cap-sd-highspeed;
@@ -221,7 +223,8 @@
&sd_emmc_c {
status = "okay";
pinctrl-0 = <&emmc_pins>;
- pinctrl-names = "default";
+ pinctrl-1 = <&emmc_clk_gate_pins>;
+ pinctrl-names = "default", "clk-gate";
bus-width = <8>;
cap-mmc-highspeed;
diff --git a/arch/arm64/boot/dts/amlogic/meson-gxl-s905x-p212.dtsi b/arch/arm64/boot/dts/amlogic/meson-gxl-s905x-p212.dtsi
index 8899121f79e1..129af9068814 100644
--- a/arch/arm64/boot/dts/amlogic/meson-gxl-s905x-p212.dtsi
+++ b/arch/arm64/boot/dts/amlogic/meson-gxl-s905x-p212.dtsi
@@ -95,7 +95,8 @@
&sd_emmc_a {
status = "okay";
pinctrl-0 = <&sdio_pins>;
- pinctrl-names = "default";
+ pinctrl-1 = <&sdio_clk_gate_pins>;
+ pinctrl-names = "default", "clk-gate";
#address-cells = <1>;
#size-cells = <0>;
@@ -116,7 +117,8 @@
&sd_emmc_b {
status = "okay";
pinctrl-0 = <&sdcard_pins>;
- pinctrl-names = "default";
+ pinctrl-1 = <&sdcard_clk_gate_pins>;
+ pinctrl-names = "default", "clk-gate";
bus-width = <4>;
cap-sd-highspeed;
@@ -134,7 +136,8 @@
&sd_emmc_c {
status = "okay";
pinctrl-0 = <&emmc_pins>;
- pinctrl-names = "default";
+ pinctrl-1 = <&emmc_clk_gate_pins>;
+ pinctrl-names = "default", "clk-gate";
bus-width = <8>;
cap-mmc-highspeed;
diff --git a/arch/arm64/boot/dts/amlogic/meson-gxl.dtsi b/arch/arm64/boot/dts/amlogic/meson-gxl.dtsi
index 071eca074a91..e3433a4bf451 100644
--- a/arch/arm64/boot/dts/amlogic/meson-gxl.dtsi
+++ b/arch/arm64/boot/dts/amlogic/meson-gxl.dtsi
@@ -271,6 +271,17 @@
};
};
+ emmc_clk_gate_pins: emmc_clk_gate {
+ mux {
+ groups = "BOOT_8";
+ function = "gpio_periphs";
+ };
+ cfg-pull-down {
+ pins = "BOOT_8";
+ bias-pull-down;
+ };
+ };
+
nor_pins: nor {
mux {
groups = "nor_d",
@@ -309,6 +320,17 @@
};
};
+ sdcard_clk_gate_pins: sdcard_clk_gate {
+ mux {
+ groups = "CARD_2";
+ function = "gpio_periphs";
+ };
+ cfg-pull-down {
+ pins = "CARD_2";
+ bias-pull-down;
+ };
+ };
+
sdio_pins: sdio {
mux {
groups = "sdio_d0",
@@ -321,6 +343,17 @@
};
};
+ sdio_clk_gate_pins: sdio_clk_gate {
+ mux {
+ groups = "GPIOX_4";
+ function = "gpio_periphs";
+ };
+ cfg-pull-down {
+ pins = "GPIOX_4";
+ bias-pull-down;
+ };
+ };
+
sdio_irq_pins: sdio_irq {
mux {
groups = "sdio_irq";
diff --git a/arch/arm64/boot/dts/amlogic/meson-gxm-nexbox-a1.dts b/arch/arm64/boot/dts/amlogic/meson-gxm-nexbox-a1.dts
index 583da09acf66..7af153535073 100644
--- a/arch/arm64/boot/dts/amlogic/meson-gxm-nexbox-a1.dts
+++ b/arch/arm64/boot/dts/amlogic/meson-gxm-nexbox-a1.dts
@@ -168,7 +168,8 @@
&sd_emmc_b {
status = "okay";
pinctrl-0 = <&sdcard_pins>;
- pinctrl-names = "default";
+ pinctrl-1 = <&sdcard_clk_gate_pins>;
+ pinctrl-names = "default", "clk-gate";
bus-width = <4>;
cap-sd-highspeed;
@@ -186,7 +187,8 @@
&sd_emmc_c {
status = "okay";
pinctrl-0 = <&emmc_pins>;
- pinctrl-names = "default";
+ pinctrl-1 = <&emmc_clk_gate_pins>;
+ pinctrl-names = "default", "clk-gate";
bus-width = <8>;
cap-mmc-highspeed;
--
2.9.5
WARNING: multiple messages have this Message-ID (diff)
From: jbrunet@baylibre.com (Jerome Brunet)
To: linux-arm-kernel@lists.infradead.org
Subject: [PATCH v2 3/9] ARM64: dts: meson: add mmc clk gate pins
Date: Mon, 21 Aug 2017 18:06:31 +0200 [thread overview]
Message-ID: <20170821160637.22456-4-jbrunet@baylibre.com> (raw)
In-Reply-To: <20170821160637.22456-1-jbrunet@baylibre.com>
Add the pinctrl to switch mmc clk pins in gpio (pulled down) mode. This
is necessary to be able to gate the clk outside of the SoC while
keeping it running in the controller
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
---
.../arm64/boot/dts/amlogic/meson-gx-p23x-q20x.dtsi | 9 ++++--
.../boot/dts/amlogic/meson-gxbb-nanopi-k2.dts | 9 ++++--
.../boot/dts/amlogic/meson-gxbb-nexbox-a95x.dts | 11 +++++---
.../arm64/boot/dts/amlogic/meson-gxbb-odroidc2.dts | 8 ++++--
arch/arm64/boot/dts/amlogic/meson-gxbb-p20x.dtsi | 9 ++++--
.../boot/dts/amlogic/meson-gxbb-vega-s95.dtsi | 9 ++++--
arch/arm64/boot/dts/amlogic/meson-gxbb.dtsi | 33 ++++++++++++++++++++++
.../dts/amlogic/meson-gxl-s905x-hwacom-amazetv.dts | 6 ++--
.../dts/amlogic/meson-gxl-s905x-libretech-cc.dts | 6 ++--
.../dts/amlogic/meson-gxl-s905x-nexbox-a95x.dts | 9 ++++--
.../boot/dts/amlogic/meson-gxl-s905x-p212.dtsi | 9 ++++--
arch/arm64/boot/dts/amlogic/meson-gxl.dtsi | 33 ++++++++++++++++++++++
.../arm64/boot/dts/amlogic/meson-gxm-nexbox-a1.dts | 6 ++--
13 files changed, 126 insertions(+), 31 deletions(-)
diff --git a/arch/arm64/boot/dts/amlogic/meson-gx-p23x-q20x.dtsi b/arch/arm64/boot/dts/amlogic/meson-gx-p23x-q20x.dtsi
index cff39c5a2632..9ac904f75013 100644
--- a/arch/arm64/boot/dts/amlogic/meson-gx-p23x-q20x.dtsi
+++ b/arch/arm64/boot/dts/amlogic/meson-gx-p23x-q20x.dtsi
@@ -161,7 +161,8 @@
&sd_emmc_a {
status = "okay";
pinctrl-0 = <&sdio_pins>;
- pinctrl-names = "default";
+ pinctrl-1 = <&sdio_clk_gate_pins>;
+ pinctrl-names = "default", "clk-gate";
#address-cells = <1>;
#size-cells = <0>;
@@ -187,7 +188,8 @@
&sd_emmc_b {
status = "okay";
pinctrl-0 = <&sdcard_pins>;
- pinctrl-names = "default";
+ pinctrl-1 = <&sdcard_clk_gate_pins>;
+ pinctrl-names = "default", "clk-gate";
bus-width = <4>;
cap-sd-highspeed;
@@ -205,7 +207,8 @@
&sd_emmc_c {
status = "okay";
pinctrl-0 = <&emmc_pins>;
- pinctrl-names = "default";
+ pinctrl-1 = <&emmc_clk_gate_pins>;
+ pinctrl-names = "default", "clk-gate";
bus-width = <8>;
cap-mmc-highspeed;
diff --git a/arch/arm64/boot/dts/amlogic/meson-gxbb-nanopi-k2.dts b/arch/arm64/boot/dts/amlogic/meson-gxbb-nanopi-k2.dts
index b48a4576158a..e4c6b2fd52ee 100644
--- a/arch/arm64/boot/dts/amlogic/meson-gxbb-nanopi-k2.dts
+++ b/arch/arm64/boot/dts/amlogic/meson-gxbb-nanopi-k2.dts
@@ -192,7 +192,8 @@
&sd_emmc_a {
status = "okay";
pinctrl-0 = <&sdio_pins>, <&sdio_irq_pins>;
- pinctrl-names = "default";
+ pinctrl-1 = <&sdio_clk_gate_pins>;
+ pinctrl-names = "default", "clk-gate";
#address-cells = <1>;
#size-cells = <0>;
@@ -218,7 +219,8 @@
&sd_emmc_b {
status = "okay";
pinctrl-0 = <&sdcard_pins>;
- pinctrl-names = "default";
+ pinctrl-1 = <&sdcard_clk_gate_pins>;
+ pinctrl-names = "default", "clk-gate";
bus-width = <4>;
cap-sd-highspeed;
@@ -236,7 +238,8 @@
&sd_emmc_c {
status = "disabled";
pinctrl-0 = <&emmc_pins>;
- pinctrl-names = "default";
+ pinctrl-1 = <&emmc_clk_gate_pins>;
+ pinctrl-names = "default", "clk-gate";
bus-width = <8>;
max-frequency = <200000000>;
diff --git a/arch/arm64/boot/dts/amlogic/meson-gxbb-nexbox-a95x.dts b/arch/arm64/boot/dts/amlogic/meson-gxbb-nexbox-a95x.dts
index c64c2256d092..7342c31f73b6 100644
--- a/arch/arm64/boot/dts/amlogic/meson-gxbb-nexbox-a95x.dts
+++ b/arch/arm64/boot/dts/amlogic/meson-gxbb-nexbox-a95x.dts
@@ -51,7 +51,7 @@
/ {
compatible = "nexbox,a95x", "amlogic,meson-gxbb";
model = "NEXBOX A95X";
-
+
aliases {
serial0 = &uart_AO;
};
@@ -225,7 +225,8 @@
&sd_emmc_a {
status = "okay";
pinctrl-0 = <&sdio_pins>;
- pinctrl-names = "default";
+ pinctrl-1 = <&sdio_clk_gate_pins>;
+ pinctrl-names = "default", "clk-gate";
#address-cells = <1>;
#size-cells = <0>;
@@ -246,7 +247,8 @@
&sd_emmc_b {
status = "okay";
pinctrl-0 = <&sdcard_pins>;
- pinctrl-names = "default";
+ pinctrl-1 = <&sdcard_clk_gate_pins>;
+ pinctrl-names = "default", "clk-gate";
bus-width = <4>;
cap-sd-highspeed;
@@ -264,7 +266,8 @@
&sd_emmc_c {
status = "okay";
pinctrl-0 = <&emmc_pins>;
- pinctrl-names = "default";
+ pinctrl-1 = <&emmc_clk_gate_pins>;
+ pinctrl-names = "default", "clk-gate";
bus-width = <8>;
cap-mmc-highspeed;
diff --git a/arch/arm64/boot/dts/amlogic/meson-gxbb-odroidc2.dts b/arch/arm64/boot/dts/amlogic/meson-gxbb-odroidc2.dts
index a12303becab4..1ffa1c238a72 100644
--- a/arch/arm64/boot/dts/amlogic/meson-gxbb-odroidc2.dts
+++ b/arch/arm64/boot/dts/amlogic/meson-gxbb-odroidc2.dts
@@ -50,7 +50,7 @@
/ {
compatible = "hardkernel,odroid-c2", "amlogic,meson-gxbb";
model = "Hardkernel ODROID-C2";
-
+
aliases {
serial0 = &uart_AO;
};
@@ -253,7 +253,8 @@
&sd_emmc_b {
status = "okay";
pinctrl-0 = <&sdcard_pins>;
- pinctrl-names = "default";
+ pinctrl-1 = <&sdcard_clk_gate_pins>;
+ pinctrl-names = "default", "clk-gate";
bus-width = <4>;
cap-sd-highspeed;
@@ -271,7 +272,8 @@
&sd_emmc_c {
status = "okay";
pinctrl-0 = <&emmc_pins>;
- pinctrl-names = "default";
+ pinctrl-1 = <&emmc_clk_gate_pins>;
+ pinctrl-names = "default", "clk-gate";
bus-width = <8>;
max-frequency = <200000000>;
diff --git a/arch/arm64/boot/dts/amlogic/meson-gxbb-p20x.dtsi b/arch/arm64/boot/dts/amlogic/meson-gxbb-p20x.dtsi
index 30b880b694de..99c409d1c8f8 100644
--- a/arch/arm64/boot/dts/amlogic/meson-gxbb-p20x.dtsi
+++ b/arch/arm64/boot/dts/amlogic/meson-gxbb-p20x.dtsi
@@ -187,7 +187,8 @@
&sd_emmc_a {
status = "okay";
pinctrl-0 = <&sdio_pins>;
- pinctrl-names = "default";
+ pinctrl-1 = <&sdio_clk_gate_pins>;
+ pinctrl-names = "default", "clk-gate";
#address-cells = <1>;
#size-cells = <0>;
@@ -213,7 +214,8 @@
&sd_emmc_b {
status = "okay";
pinctrl-0 = <&sdcard_pins>;
- pinctrl-names = "default";
+ pinctrl-1 = <&sdcard_clk_gate_pins>;
+ pinctrl-names = "default", "clk-gate";
bus-width = <4>;
cap-sd-highspeed;
@@ -231,7 +233,8 @@
&sd_emmc_c {
status = "okay";
pinctrl-0 = <&emmc_pins>;
- pinctrl-names = "default";
+ pinctrl-1 = <&emmc_clk_gate_pins>;
+ pinctrl-names = "default", "clk-gate";
bus-width = <8>;
cap-mmc-highspeed;
diff --git a/arch/arm64/boot/dts/amlogic/meson-gxbb-vega-s95.dtsi b/arch/arm64/boot/dts/amlogic/meson-gxbb-vega-s95.dtsi
index 0262ef8d48e4..f2bc6dea1fc6 100644
--- a/arch/arm64/boot/dts/amlogic/meson-gxbb-vega-s95.dtsi
+++ b/arch/arm64/boot/dts/amlogic/meson-gxbb-vega-s95.dtsi
@@ -155,7 +155,8 @@
&sd_emmc_a {
status = "okay";
pinctrl-0 = <&sdio_pins &sdio_irq_pins>;
- pinctrl-names = "default";
+ pinctrl-1 = <&sdio_clk_gate_pins>;
+ pinctrl-names = "default", "clk-gate";
#address-cells = <1>;
#size-cells = <0>;
@@ -181,7 +182,8 @@
&sd_emmc_b {
status = "okay";
pinctrl-0 = <&sdcard_pins>;
- pinctrl-names = "default";
+ pinctrl-1 = <&sdcard_clk_gate_pins>;
+ pinctrl-names = "default", "clk-gate";
bus-width = <4>;
cap-sd-highspeed;
@@ -198,7 +200,8 @@
&sd_emmc_c {
status = "okay";
pinctrl-0 = <&emmc_pins>;
- pinctrl-names = "default";
+ pinctrl-1 = <&emmc_clk_gate_pins>;
+ pinctrl-names = "default", "clk-gate";
bus-width = <8>;
cap-mmc-highspeed;
diff --git a/arch/arm64/boot/dts/amlogic/meson-gxbb.dtsi b/arch/arm64/boot/dts/amlogic/meson-gxbb.dtsi
index 9a1e478f80d5..1d6314e2eb8a 100644
--- a/arch/arm64/boot/dts/amlogic/meson-gxbb.dtsi
+++ b/arch/arm64/boot/dts/amlogic/meson-gxbb.dtsi
@@ -383,6 +383,17 @@
};
};
+ emmc_clk_gate_pins: emmc_clk_gate {
+ mux {
+ groups = "BOOT_8";
+ function = "gpio_periphs";
+ };
+ cfg-pull-down {
+ pins = "BOOT_8";
+ bias-pull-down;
+ };
+ };
+
nor_pins: nor {
mux {
groups = "nor_d",
@@ -421,6 +432,17 @@
};
};
+ sdcard_clk_gate_pins: sdcard_clk_gate {
+ mux {
+ groups = "CARD_2";
+ function = "gpio_periphs";
+ };
+ cfg-pull-down {
+ pins = "CARD_2";
+ bias-pull-down;
+ };
+ };
+
sdio_pins: sdio {
mux {
groups = "sdio_d0",
@@ -433,6 +455,17 @@
};
};
+ sdio_clk_gate_pins: sdio_clk_gate {
+ mux {
+ groups = "GPIOX_4";
+ function = "gpio_periphs";
+ };
+ cfg-pull-down {
+ pins = "GPIOX_4";
+ bias-pull-down;
+ };
+ };
+
sdio_irq_pins: sdio_irq {
mux {
groups = "sdio_irq";
diff --git a/arch/arm64/boot/dts/amlogic/meson-gxl-s905x-hwacom-amazetv.dts b/arch/arm64/boot/dts/amlogic/meson-gxl-s905x-hwacom-amazetv.dts
index f779a985f923..977b4240f3c1 100644
--- a/arch/arm64/boot/dts/amlogic/meson-gxl-s905x-hwacom-amazetv.dts
+++ b/arch/arm64/boot/dts/amlogic/meson-gxl-s905x-hwacom-amazetv.dts
@@ -123,7 +123,8 @@
&sd_emmc_b {
status = "okay";
pinctrl-0 = <&sdcard_pins>;
- pinctrl-names = "default";
+ pinctrl-1 = <&sdcard_clk_gate_pins>;
+ pinctrl-names = "default", "clk-gate";
bus-width = <4>;
cap-sd-highspeed;
@@ -141,7 +142,8 @@
&sd_emmc_c {
status = "okay";
pinctrl-0 = <&emmc_pins>;
- pinctrl-names = "default";
+ pinctrl-1 = <&emmc_clk_gate_pins>;
+ pinctrl-names = "default", "clk-gate";
bus-width = <8>;
cap-mmc-highspeed;
diff --git a/arch/arm64/boot/dts/amlogic/meson-gxl-s905x-libretech-cc.dts b/arch/arm64/boot/dts/amlogic/meson-gxl-s905x-libretech-cc.dts
index 51c4ecc3b31e..2b56f7d9be2b 100644
--- a/arch/arm64/boot/dts/amlogic/meson-gxl-s905x-libretech-cc.dts
+++ b/arch/arm64/boot/dts/amlogic/meson-gxl-s905x-libretech-cc.dts
@@ -134,7 +134,8 @@
&sd_emmc_b {
status = "okay";
pinctrl-0 = <&sdcard_pins>;
- pinctrl-names = "default";
+ pinctrl-1 = <&sdcard_clk_gate_pins>;
+ pinctrl-names = "default", "clk-gate";
bus-width = <4>;
cap-sd-highspeed;
@@ -156,7 +157,8 @@
&sd_emmc_c {
status = "okay";
pinctrl-0 = <&emmc_pins>;
- pinctrl-names = "default";
+ pinctrl-1 = <&emmc_clk_gate_pins>;
+ pinctrl-names = "default", "clk-gate";
bus-width = <8>;
cap-mmc-highspeed;
diff --git a/arch/arm64/boot/dts/amlogic/meson-gxl-s905x-nexbox-a95x.dts b/arch/arm64/boot/dts/amlogic/meson-gxl-s905x-nexbox-a95x.dts
index 83c35efbae8b..df448b11a16b 100644
--- a/arch/arm64/boot/dts/amlogic/meson-gxl-s905x-nexbox-a95x.dts
+++ b/arch/arm64/boot/dts/amlogic/meson-gxl-s905x-nexbox-a95x.dts
@@ -182,7 +182,8 @@
&sd_emmc_a {
status = "okay";
pinctrl-0 = <&sdio_pins>;
- pinctrl-names = "default";
+ pinctrl-1 = <&sdio_clk_gate_pins>;
+ pinctrl-names = "default", "clk-gate";
#address-cells = <1>;
#size-cells = <0>;
@@ -203,7 +204,8 @@
&sd_emmc_b {
status = "okay";
pinctrl-0 = <&sdcard_pins>;
- pinctrl-names = "default";
+ pinctrl-1 = <&sdcard_clk_gate_pins>;
+ pinctrl-names = "default", "clk-gate";
bus-width = <4>;
cap-sd-highspeed;
@@ -221,7 +223,8 @@
&sd_emmc_c {
status = "okay";
pinctrl-0 = <&emmc_pins>;
- pinctrl-names = "default";
+ pinctrl-1 = <&emmc_clk_gate_pins>;
+ pinctrl-names = "default", "clk-gate";
bus-width = <8>;
cap-mmc-highspeed;
diff --git a/arch/arm64/boot/dts/amlogic/meson-gxl-s905x-p212.dtsi b/arch/arm64/boot/dts/amlogic/meson-gxl-s905x-p212.dtsi
index 8899121f79e1..129af9068814 100644
--- a/arch/arm64/boot/dts/amlogic/meson-gxl-s905x-p212.dtsi
+++ b/arch/arm64/boot/dts/amlogic/meson-gxl-s905x-p212.dtsi
@@ -95,7 +95,8 @@
&sd_emmc_a {
status = "okay";
pinctrl-0 = <&sdio_pins>;
- pinctrl-names = "default";
+ pinctrl-1 = <&sdio_clk_gate_pins>;
+ pinctrl-names = "default", "clk-gate";
#address-cells = <1>;
#size-cells = <0>;
@@ -116,7 +117,8 @@
&sd_emmc_b {
status = "okay";
pinctrl-0 = <&sdcard_pins>;
- pinctrl-names = "default";
+ pinctrl-1 = <&sdcard_clk_gate_pins>;
+ pinctrl-names = "default", "clk-gate";
bus-width = <4>;
cap-sd-highspeed;
@@ -134,7 +136,8 @@
&sd_emmc_c {
status = "okay";
pinctrl-0 = <&emmc_pins>;
- pinctrl-names = "default";
+ pinctrl-1 = <&emmc_clk_gate_pins>;
+ pinctrl-names = "default", "clk-gate";
bus-width = <8>;
cap-mmc-highspeed;
diff --git a/arch/arm64/boot/dts/amlogic/meson-gxl.dtsi b/arch/arm64/boot/dts/amlogic/meson-gxl.dtsi
index 071eca074a91..e3433a4bf451 100644
--- a/arch/arm64/boot/dts/amlogic/meson-gxl.dtsi
+++ b/arch/arm64/boot/dts/amlogic/meson-gxl.dtsi
@@ -271,6 +271,17 @@
};
};
+ emmc_clk_gate_pins: emmc_clk_gate {
+ mux {
+ groups = "BOOT_8";
+ function = "gpio_periphs";
+ };
+ cfg-pull-down {
+ pins = "BOOT_8";
+ bias-pull-down;
+ };
+ };
+
nor_pins: nor {
mux {
groups = "nor_d",
@@ -309,6 +320,17 @@
};
};
+ sdcard_clk_gate_pins: sdcard_clk_gate {
+ mux {
+ groups = "CARD_2";
+ function = "gpio_periphs";
+ };
+ cfg-pull-down {
+ pins = "CARD_2";
+ bias-pull-down;
+ };
+ };
+
sdio_pins: sdio {
mux {
groups = "sdio_d0",
@@ -321,6 +343,17 @@
};
};
+ sdio_clk_gate_pins: sdio_clk_gate {
+ mux {
+ groups = "GPIOX_4";
+ function = "gpio_periphs";
+ };
+ cfg-pull-down {
+ pins = "GPIOX_4";
+ bias-pull-down;
+ };
+ };
+
sdio_irq_pins: sdio_irq {
mux {
groups = "sdio_irq";
diff --git a/arch/arm64/boot/dts/amlogic/meson-gxm-nexbox-a1.dts b/arch/arm64/boot/dts/amlogic/meson-gxm-nexbox-a1.dts
index 583da09acf66..7af153535073 100644
--- a/arch/arm64/boot/dts/amlogic/meson-gxm-nexbox-a1.dts
+++ b/arch/arm64/boot/dts/amlogic/meson-gxm-nexbox-a1.dts
@@ -168,7 +168,8 @@
&sd_emmc_b {
status = "okay";
pinctrl-0 = <&sdcard_pins>;
- pinctrl-names = "default";
+ pinctrl-1 = <&sdcard_clk_gate_pins>;
+ pinctrl-names = "default", "clk-gate";
bus-width = <4>;
cap-sd-highspeed;
@@ -186,7 +187,8 @@
&sd_emmc_c {
status = "okay";
pinctrl-0 = <&emmc_pins>;
- pinctrl-names = "default";
+ pinctrl-1 = <&emmc_clk_gate_pins>;
+ pinctrl-names = "default", "clk-gate";
bus-width = <8>;
cap-mmc-highspeed;
--
2.9.5
WARNING: multiple messages have this Message-ID (diff)
From: jbrunet@baylibre.com (Jerome Brunet)
To: linus-amlogic@lists.infradead.org
Subject: [PATCH v2 3/9] ARM64: dts: meson: add mmc clk gate pins
Date: Mon, 21 Aug 2017 18:06:31 +0200 [thread overview]
Message-ID: <20170821160637.22456-4-jbrunet@baylibre.com> (raw)
In-Reply-To: <20170821160637.22456-1-jbrunet@baylibre.com>
Add the pinctrl to switch mmc clk pins in gpio (pulled down) mode. This
is necessary to be able to gate the clk outside of the SoC while
keeping it running in the controller
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
---
.../arm64/boot/dts/amlogic/meson-gx-p23x-q20x.dtsi | 9 ++++--
.../boot/dts/amlogic/meson-gxbb-nanopi-k2.dts | 9 ++++--
.../boot/dts/amlogic/meson-gxbb-nexbox-a95x.dts | 11 +++++---
.../arm64/boot/dts/amlogic/meson-gxbb-odroidc2.dts | 8 ++++--
arch/arm64/boot/dts/amlogic/meson-gxbb-p20x.dtsi | 9 ++++--
.../boot/dts/amlogic/meson-gxbb-vega-s95.dtsi | 9 ++++--
arch/arm64/boot/dts/amlogic/meson-gxbb.dtsi | 33 ++++++++++++++++++++++
.../dts/amlogic/meson-gxl-s905x-hwacom-amazetv.dts | 6 ++--
.../dts/amlogic/meson-gxl-s905x-libretech-cc.dts | 6 ++--
.../dts/amlogic/meson-gxl-s905x-nexbox-a95x.dts | 9 ++++--
.../boot/dts/amlogic/meson-gxl-s905x-p212.dtsi | 9 ++++--
arch/arm64/boot/dts/amlogic/meson-gxl.dtsi | 33 ++++++++++++++++++++++
.../arm64/boot/dts/amlogic/meson-gxm-nexbox-a1.dts | 6 ++--
13 files changed, 126 insertions(+), 31 deletions(-)
diff --git a/arch/arm64/boot/dts/amlogic/meson-gx-p23x-q20x.dtsi b/arch/arm64/boot/dts/amlogic/meson-gx-p23x-q20x.dtsi
index cff39c5a2632..9ac904f75013 100644
--- a/arch/arm64/boot/dts/amlogic/meson-gx-p23x-q20x.dtsi
+++ b/arch/arm64/boot/dts/amlogic/meson-gx-p23x-q20x.dtsi
@@ -161,7 +161,8 @@
&sd_emmc_a {
status = "okay";
pinctrl-0 = <&sdio_pins>;
- pinctrl-names = "default";
+ pinctrl-1 = <&sdio_clk_gate_pins>;
+ pinctrl-names = "default", "clk-gate";
#address-cells = <1>;
#size-cells = <0>;
@@ -187,7 +188,8 @@
&sd_emmc_b {
status = "okay";
pinctrl-0 = <&sdcard_pins>;
- pinctrl-names = "default";
+ pinctrl-1 = <&sdcard_clk_gate_pins>;
+ pinctrl-names = "default", "clk-gate";
bus-width = <4>;
cap-sd-highspeed;
@@ -205,7 +207,8 @@
&sd_emmc_c {
status = "okay";
pinctrl-0 = <&emmc_pins>;
- pinctrl-names = "default";
+ pinctrl-1 = <&emmc_clk_gate_pins>;
+ pinctrl-names = "default", "clk-gate";
bus-width = <8>;
cap-mmc-highspeed;
diff --git a/arch/arm64/boot/dts/amlogic/meson-gxbb-nanopi-k2.dts b/arch/arm64/boot/dts/amlogic/meson-gxbb-nanopi-k2.dts
index b48a4576158a..e4c6b2fd52ee 100644
--- a/arch/arm64/boot/dts/amlogic/meson-gxbb-nanopi-k2.dts
+++ b/arch/arm64/boot/dts/amlogic/meson-gxbb-nanopi-k2.dts
@@ -192,7 +192,8 @@
&sd_emmc_a {
status = "okay";
pinctrl-0 = <&sdio_pins>, <&sdio_irq_pins>;
- pinctrl-names = "default";
+ pinctrl-1 = <&sdio_clk_gate_pins>;
+ pinctrl-names = "default", "clk-gate";
#address-cells = <1>;
#size-cells = <0>;
@@ -218,7 +219,8 @@
&sd_emmc_b {
status = "okay";
pinctrl-0 = <&sdcard_pins>;
- pinctrl-names = "default";
+ pinctrl-1 = <&sdcard_clk_gate_pins>;
+ pinctrl-names = "default", "clk-gate";
bus-width = <4>;
cap-sd-highspeed;
@@ -236,7 +238,8 @@
&sd_emmc_c {
status = "disabled";
pinctrl-0 = <&emmc_pins>;
- pinctrl-names = "default";
+ pinctrl-1 = <&emmc_clk_gate_pins>;
+ pinctrl-names = "default", "clk-gate";
bus-width = <8>;
max-frequency = <200000000>;
diff --git a/arch/arm64/boot/dts/amlogic/meson-gxbb-nexbox-a95x.dts b/arch/arm64/boot/dts/amlogic/meson-gxbb-nexbox-a95x.dts
index c64c2256d092..7342c31f73b6 100644
--- a/arch/arm64/boot/dts/amlogic/meson-gxbb-nexbox-a95x.dts
+++ b/arch/arm64/boot/dts/amlogic/meson-gxbb-nexbox-a95x.dts
@@ -51,7 +51,7 @@
/ {
compatible = "nexbox,a95x", "amlogic,meson-gxbb";
model = "NEXBOX A95X";
-
+
aliases {
serial0 = &uart_AO;
};
@@ -225,7 +225,8 @@
&sd_emmc_a {
status = "okay";
pinctrl-0 = <&sdio_pins>;
- pinctrl-names = "default";
+ pinctrl-1 = <&sdio_clk_gate_pins>;
+ pinctrl-names = "default", "clk-gate";
#address-cells = <1>;
#size-cells = <0>;
@@ -246,7 +247,8 @@
&sd_emmc_b {
status = "okay";
pinctrl-0 = <&sdcard_pins>;
- pinctrl-names = "default";
+ pinctrl-1 = <&sdcard_clk_gate_pins>;
+ pinctrl-names = "default", "clk-gate";
bus-width = <4>;
cap-sd-highspeed;
@@ -264,7 +266,8 @@
&sd_emmc_c {
status = "okay";
pinctrl-0 = <&emmc_pins>;
- pinctrl-names = "default";
+ pinctrl-1 = <&emmc_clk_gate_pins>;
+ pinctrl-names = "default", "clk-gate";
bus-width = <8>;
cap-mmc-highspeed;
diff --git a/arch/arm64/boot/dts/amlogic/meson-gxbb-odroidc2.dts b/arch/arm64/boot/dts/amlogic/meson-gxbb-odroidc2.dts
index a12303becab4..1ffa1c238a72 100644
--- a/arch/arm64/boot/dts/amlogic/meson-gxbb-odroidc2.dts
+++ b/arch/arm64/boot/dts/amlogic/meson-gxbb-odroidc2.dts
@@ -50,7 +50,7 @@
/ {
compatible = "hardkernel,odroid-c2", "amlogic,meson-gxbb";
model = "Hardkernel ODROID-C2";
-
+
aliases {
serial0 = &uart_AO;
};
@@ -253,7 +253,8 @@
&sd_emmc_b {
status = "okay";
pinctrl-0 = <&sdcard_pins>;
- pinctrl-names = "default";
+ pinctrl-1 = <&sdcard_clk_gate_pins>;
+ pinctrl-names = "default", "clk-gate";
bus-width = <4>;
cap-sd-highspeed;
@@ -271,7 +272,8 @@
&sd_emmc_c {
status = "okay";
pinctrl-0 = <&emmc_pins>;
- pinctrl-names = "default";
+ pinctrl-1 = <&emmc_clk_gate_pins>;
+ pinctrl-names = "default", "clk-gate";
bus-width = <8>;
max-frequency = <200000000>;
diff --git a/arch/arm64/boot/dts/amlogic/meson-gxbb-p20x.dtsi b/arch/arm64/boot/dts/amlogic/meson-gxbb-p20x.dtsi
index 30b880b694de..99c409d1c8f8 100644
--- a/arch/arm64/boot/dts/amlogic/meson-gxbb-p20x.dtsi
+++ b/arch/arm64/boot/dts/amlogic/meson-gxbb-p20x.dtsi
@@ -187,7 +187,8 @@
&sd_emmc_a {
status = "okay";
pinctrl-0 = <&sdio_pins>;
- pinctrl-names = "default";
+ pinctrl-1 = <&sdio_clk_gate_pins>;
+ pinctrl-names = "default", "clk-gate";
#address-cells = <1>;
#size-cells = <0>;
@@ -213,7 +214,8 @@
&sd_emmc_b {
status = "okay";
pinctrl-0 = <&sdcard_pins>;
- pinctrl-names = "default";
+ pinctrl-1 = <&sdcard_clk_gate_pins>;
+ pinctrl-names = "default", "clk-gate";
bus-width = <4>;
cap-sd-highspeed;
@@ -231,7 +233,8 @@
&sd_emmc_c {
status = "okay";
pinctrl-0 = <&emmc_pins>;
- pinctrl-names = "default";
+ pinctrl-1 = <&emmc_clk_gate_pins>;
+ pinctrl-names = "default", "clk-gate";
bus-width = <8>;
cap-mmc-highspeed;
diff --git a/arch/arm64/boot/dts/amlogic/meson-gxbb-vega-s95.dtsi b/arch/arm64/boot/dts/amlogic/meson-gxbb-vega-s95.dtsi
index 0262ef8d48e4..f2bc6dea1fc6 100644
--- a/arch/arm64/boot/dts/amlogic/meson-gxbb-vega-s95.dtsi
+++ b/arch/arm64/boot/dts/amlogic/meson-gxbb-vega-s95.dtsi
@@ -155,7 +155,8 @@
&sd_emmc_a {
status = "okay";
pinctrl-0 = <&sdio_pins &sdio_irq_pins>;
- pinctrl-names = "default";
+ pinctrl-1 = <&sdio_clk_gate_pins>;
+ pinctrl-names = "default", "clk-gate";
#address-cells = <1>;
#size-cells = <0>;
@@ -181,7 +182,8 @@
&sd_emmc_b {
status = "okay";
pinctrl-0 = <&sdcard_pins>;
- pinctrl-names = "default";
+ pinctrl-1 = <&sdcard_clk_gate_pins>;
+ pinctrl-names = "default", "clk-gate";
bus-width = <4>;
cap-sd-highspeed;
@@ -198,7 +200,8 @@
&sd_emmc_c {
status = "okay";
pinctrl-0 = <&emmc_pins>;
- pinctrl-names = "default";
+ pinctrl-1 = <&emmc_clk_gate_pins>;
+ pinctrl-names = "default", "clk-gate";
bus-width = <8>;
cap-mmc-highspeed;
diff --git a/arch/arm64/boot/dts/amlogic/meson-gxbb.dtsi b/arch/arm64/boot/dts/amlogic/meson-gxbb.dtsi
index 9a1e478f80d5..1d6314e2eb8a 100644
--- a/arch/arm64/boot/dts/amlogic/meson-gxbb.dtsi
+++ b/arch/arm64/boot/dts/amlogic/meson-gxbb.dtsi
@@ -383,6 +383,17 @@
};
};
+ emmc_clk_gate_pins: emmc_clk_gate {
+ mux {
+ groups = "BOOT_8";
+ function = "gpio_periphs";
+ };
+ cfg-pull-down {
+ pins = "BOOT_8";
+ bias-pull-down;
+ };
+ };
+
nor_pins: nor {
mux {
groups = "nor_d",
@@ -421,6 +432,17 @@
};
};
+ sdcard_clk_gate_pins: sdcard_clk_gate {
+ mux {
+ groups = "CARD_2";
+ function = "gpio_periphs";
+ };
+ cfg-pull-down {
+ pins = "CARD_2";
+ bias-pull-down;
+ };
+ };
+
sdio_pins: sdio {
mux {
groups = "sdio_d0",
@@ -433,6 +455,17 @@
};
};
+ sdio_clk_gate_pins: sdio_clk_gate {
+ mux {
+ groups = "GPIOX_4";
+ function = "gpio_periphs";
+ };
+ cfg-pull-down {
+ pins = "GPIOX_4";
+ bias-pull-down;
+ };
+ };
+
sdio_irq_pins: sdio_irq {
mux {
groups = "sdio_irq";
diff --git a/arch/arm64/boot/dts/amlogic/meson-gxl-s905x-hwacom-amazetv.dts b/arch/arm64/boot/dts/amlogic/meson-gxl-s905x-hwacom-amazetv.dts
index f779a985f923..977b4240f3c1 100644
--- a/arch/arm64/boot/dts/amlogic/meson-gxl-s905x-hwacom-amazetv.dts
+++ b/arch/arm64/boot/dts/amlogic/meson-gxl-s905x-hwacom-amazetv.dts
@@ -123,7 +123,8 @@
&sd_emmc_b {
status = "okay";
pinctrl-0 = <&sdcard_pins>;
- pinctrl-names = "default";
+ pinctrl-1 = <&sdcard_clk_gate_pins>;
+ pinctrl-names = "default", "clk-gate";
bus-width = <4>;
cap-sd-highspeed;
@@ -141,7 +142,8 @@
&sd_emmc_c {
status = "okay";
pinctrl-0 = <&emmc_pins>;
- pinctrl-names = "default";
+ pinctrl-1 = <&emmc_clk_gate_pins>;
+ pinctrl-names = "default", "clk-gate";
bus-width = <8>;
cap-mmc-highspeed;
diff --git a/arch/arm64/boot/dts/amlogic/meson-gxl-s905x-libretech-cc.dts b/arch/arm64/boot/dts/amlogic/meson-gxl-s905x-libretech-cc.dts
index 51c4ecc3b31e..2b56f7d9be2b 100644
--- a/arch/arm64/boot/dts/amlogic/meson-gxl-s905x-libretech-cc.dts
+++ b/arch/arm64/boot/dts/amlogic/meson-gxl-s905x-libretech-cc.dts
@@ -134,7 +134,8 @@
&sd_emmc_b {
status = "okay";
pinctrl-0 = <&sdcard_pins>;
- pinctrl-names = "default";
+ pinctrl-1 = <&sdcard_clk_gate_pins>;
+ pinctrl-names = "default", "clk-gate";
bus-width = <4>;
cap-sd-highspeed;
@@ -156,7 +157,8 @@
&sd_emmc_c {
status = "okay";
pinctrl-0 = <&emmc_pins>;
- pinctrl-names = "default";
+ pinctrl-1 = <&emmc_clk_gate_pins>;
+ pinctrl-names = "default", "clk-gate";
bus-width = <8>;
cap-mmc-highspeed;
diff --git a/arch/arm64/boot/dts/amlogic/meson-gxl-s905x-nexbox-a95x.dts b/arch/arm64/boot/dts/amlogic/meson-gxl-s905x-nexbox-a95x.dts
index 83c35efbae8b..df448b11a16b 100644
--- a/arch/arm64/boot/dts/amlogic/meson-gxl-s905x-nexbox-a95x.dts
+++ b/arch/arm64/boot/dts/amlogic/meson-gxl-s905x-nexbox-a95x.dts
@@ -182,7 +182,8 @@
&sd_emmc_a {
status = "okay";
pinctrl-0 = <&sdio_pins>;
- pinctrl-names = "default";
+ pinctrl-1 = <&sdio_clk_gate_pins>;
+ pinctrl-names = "default", "clk-gate";
#address-cells = <1>;
#size-cells = <0>;
@@ -203,7 +204,8 @@
&sd_emmc_b {
status = "okay";
pinctrl-0 = <&sdcard_pins>;
- pinctrl-names = "default";
+ pinctrl-1 = <&sdcard_clk_gate_pins>;
+ pinctrl-names = "default", "clk-gate";
bus-width = <4>;
cap-sd-highspeed;
@@ -221,7 +223,8 @@
&sd_emmc_c {
status = "okay";
pinctrl-0 = <&emmc_pins>;
- pinctrl-names = "default";
+ pinctrl-1 = <&emmc_clk_gate_pins>;
+ pinctrl-names = "default", "clk-gate";
bus-width = <8>;
cap-mmc-highspeed;
diff --git a/arch/arm64/boot/dts/amlogic/meson-gxl-s905x-p212.dtsi b/arch/arm64/boot/dts/amlogic/meson-gxl-s905x-p212.dtsi
index 8899121f79e1..129af9068814 100644
--- a/arch/arm64/boot/dts/amlogic/meson-gxl-s905x-p212.dtsi
+++ b/arch/arm64/boot/dts/amlogic/meson-gxl-s905x-p212.dtsi
@@ -95,7 +95,8 @@
&sd_emmc_a {
status = "okay";
pinctrl-0 = <&sdio_pins>;
- pinctrl-names = "default";
+ pinctrl-1 = <&sdio_clk_gate_pins>;
+ pinctrl-names = "default", "clk-gate";
#address-cells = <1>;
#size-cells = <0>;
@@ -116,7 +117,8 @@
&sd_emmc_b {
status = "okay";
pinctrl-0 = <&sdcard_pins>;
- pinctrl-names = "default";
+ pinctrl-1 = <&sdcard_clk_gate_pins>;
+ pinctrl-names = "default", "clk-gate";
bus-width = <4>;
cap-sd-highspeed;
@@ -134,7 +136,8 @@
&sd_emmc_c {
status = "okay";
pinctrl-0 = <&emmc_pins>;
- pinctrl-names = "default";
+ pinctrl-1 = <&emmc_clk_gate_pins>;
+ pinctrl-names = "default", "clk-gate";
bus-width = <8>;
cap-mmc-highspeed;
diff --git a/arch/arm64/boot/dts/amlogic/meson-gxl.dtsi b/arch/arm64/boot/dts/amlogic/meson-gxl.dtsi
index 071eca074a91..e3433a4bf451 100644
--- a/arch/arm64/boot/dts/amlogic/meson-gxl.dtsi
+++ b/arch/arm64/boot/dts/amlogic/meson-gxl.dtsi
@@ -271,6 +271,17 @@
};
};
+ emmc_clk_gate_pins: emmc_clk_gate {
+ mux {
+ groups = "BOOT_8";
+ function = "gpio_periphs";
+ };
+ cfg-pull-down {
+ pins = "BOOT_8";
+ bias-pull-down;
+ };
+ };
+
nor_pins: nor {
mux {
groups = "nor_d",
@@ -309,6 +320,17 @@
};
};
+ sdcard_clk_gate_pins: sdcard_clk_gate {
+ mux {
+ groups = "CARD_2";
+ function = "gpio_periphs";
+ };
+ cfg-pull-down {
+ pins = "CARD_2";
+ bias-pull-down;
+ };
+ };
+
sdio_pins: sdio {
mux {
groups = "sdio_d0",
@@ -321,6 +343,17 @@
};
};
+ sdio_clk_gate_pins: sdio_clk_gate {
+ mux {
+ groups = "GPIOX_4";
+ function = "gpio_periphs";
+ };
+ cfg-pull-down {
+ pins = "GPIOX_4";
+ bias-pull-down;
+ };
+ };
+
sdio_irq_pins: sdio_irq {
mux {
groups = "sdio_irq";
diff --git a/arch/arm64/boot/dts/amlogic/meson-gxm-nexbox-a1.dts b/arch/arm64/boot/dts/amlogic/meson-gxm-nexbox-a1.dts
index 583da09acf66..7af153535073 100644
--- a/arch/arm64/boot/dts/amlogic/meson-gxm-nexbox-a1.dts
+++ b/arch/arm64/boot/dts/amlogic/meson-gxm-nexbox-a1.dts
@@ -168,7 +168,8 @@
&sd_emmc_b {
status = "okay";
pinctrl-0 = <&sdcard_pins>;
- pinctrl-names = "default";
+ pinctrl-1 = <&sdcard_clk_gate_pins>;
+ pinctrl-names = "default", "clk-gate";
bus-width = <4>;
cap-sd-highspeed;
@@ -186,7 +187,8 @@
&sd_emmc_c {
status = "okay";
pinctrl-0 = <&emmc_pins>;
- pinctrl-names = "default";
+ pinctrl-1 = <&emmc_clk_gate_pins>;
+ pinctrl-names = "default", "clk-gate";
bus-width = <8>;
cap-mmc-highspeed;
--
2.9.5
next prev parent reply other threads:[~2017-08-21 16:08 UTC|newest]
Thread overview: 31+ messages / expand[flat|nested] mbox.gz Atom feed top
2017-08-21 16:06 [PATCH v2 0/9] ARM64: dts: meson: update around mmc Jerome Brunet
2017-08-21 16:06 ` Jerome Brunet
2017-08-21 16:06 ` Jerome Brunet
2017-08-21 16:06 ` [PATCH v2 1/9] ARM64: dts: meson-gx: Use correct mmc clock source 0 Jerome Brunet
2017-08-21 16:06 ` Jerome Brunet
2017-08-21 16:06 ` Jerome Brunet
2017-08-21 16:06 ` [PATCH v2 2/9] ARM64: dts: meson: remove cap-sd-highspeed from emmc nodes Jerome Brunet
2017-08-21 16:06 ` Jerome Brunet
2017-08-21 16:06 ` Jerome Brunet
2017-08-21 16:06 ` Jerome Brunet
2017-08-21 16:06 ` Jerome Brunet [this message]
2017-08-21 16:06 ` [PATCH v2 3/9] ARM64: dts: meson: add mmc clk gate pins Jerome Brunet
2017-08-21 16:06 ` Jerome Brunet
2017-08-21 16:06 ` [PATCH v2 4/9] ARM64: dts: meson-gxbb: nanopi-k2: add card regulator settle times Jerome Brunet
2017-08-21 16:06 ` Jerome Brunet
2017-08-21 16:06 ` Jerome Brunet
2017-08-21 16:06 ` [PATCH v2 5/9] ARM64: dts: meson-gxl: libretech-cc: " Jerome Brunet
2017-08-21 16:06 ` Jerome Brunet
2017-08-21 16:06 ` Jerome Brunet
2017-08-21 16:06 ` [PATCH v2 6/9] ARM64: dts: meson-gxl: libretech-cc: remove sdr104 capability Jerome Brunet
2017-08-21 16:06 ` Jerome Brunet
2017-08-21 16:06 ` Jerome Brunet
2017-08-21 16:06 ` [PATCH v2 7/9] ARM64: dts: meson-gxbb: p20x: enable sdcard UHS modes Jerome Brunet
2017-08-21 16:06 ` Jerome Brunet
2017-08-21 16:06 ` Jerome Brunet
2017-08-21 16:06 ` [PATCH v2 8/9] ARM64: dts: meson-gxbb: nanopi-k2: " Jerome Brunet
2017-08-21 16:06 ` Jerome Brunet
2017-08-21 16:06 ` Jerome Brunet
2017-08-21 16:06 ` [PATCH v2 9/9] ARM64: dts: meson-gxbb: nanopi-k2: enable sdr104 mode Jerome Brunet
2017-08-21 16:06 ` Jerome Brunet
2017-08-21 16:06 ` Jerome Brunet
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20170821160637.22456-4-jbrunet@baylibre.com \
--to=jbrunet@baylibre.com \
--cc=carlo@caione.org \
--cc=devicetree@vger.kernel.org \
--cc=khilman@baylibre.com \
--cc=linux-amlogic@lists.infradead.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.