From: Kishon Vijay Abraham I <kishon@ti.com> To: Kishon Vijay Abraham I <kishon@ti.com>, Bjorn Helgaas <bhelgaas@google.com> Cc: Roger Quadros <rogerq@ti.com>, <linux-omap@vger.kernel.org>, <linux-pci@vger.kernel.org>, <linux-kernel@vger.kernel.org>, <nsekhar@ti.com>, Vignesh R <vigneshr@ti.com> Subject: [PATCH 2/2] phy: ti-pipe3: Update pcie phy settings Date: Mon, 9 Oct 2017 14:33:38 +0530 [thread overview] Message-ID: <20171009090338.26033-3-kishon@ti.com> (raw) In-Reply-To: <20171009090338.26033-1-kishon@ti.com> Update the PCIe phy settings based on new settings available in AM572x Technical Reference Manual[1] Revision I, revised April 2017 in Table 26-62 "Preferred PCIe_PHY_RX SCP Register Settings". [1] http://www.ti.com/lit/ug/spruhz6i/spruhz6i.pdf Cc: Vignesh R <vigneshr@ti.com> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> [nsekhar@ti.com: commit message updates] Signed-off-by: Sekhar Nori <nsekhar@ti.com> --- drivers/phy/ti/phy-ti-pipe3.c | 101 +++++++++++++++++++++++++++++++++++++++++- 1 file changed, 100 insertions(+), 1 deletion(-) diff --git a/drivers/phy/ti/phy-ti-pipe3.c b/drivers/phy/ti/phy-ti-pipe3.c index 0e564f32749f..68ce4a082b9b 100644 --- a/drivers/phy/ti/phy-ti-pipe3.c +++ b/drivers/phy/ti/phy-ti-pipe3.c @@ -68,6 +68,40 @@ #define PCIE_PCS_MASK 0xFF0000 #define PCIE_PCS_DELAY_COUNT_SHIFT 0x10 +#define PCIEPHYRX_ANA_PROGRAMMABILITY 0x0000000C +#define INTERFACE_MASK GENMASK(31, 27) +#define INTERFACE_SHIFT 27 +#define LOSD_MASK GENMASK(17, 14) +#define LOSD_SHIFT 14 +#define MEM_PLLDIV GENMASK(6, 5) + +#define PCIEPHYRX_TRIM 0x0000001C +#define MEM_DLL_TRIM_SEL GENMASK(31, 30) +#define MEM_DLL_TRIM_SHIFT 30 + +#define PCIEPHYRX_DLL 0x00000024 +#define MEM_DLL_PHINT_RATE GENMASK(31, 30) + +#define PCIEPHYRX_DIGITAL_MODES 0x00000028 +#define MEM_CDR_FASTLOCK BIT(23) +#define MEM_CDR_LBW GENMASK(22, 21) +#define MEM_CDR_STEPCNT GENMASK(20, 19) +#define MEM_CDR_STL_MASK GENMASK(18, 16) +#define MEM_CDR_STL_SHIFT 16 +#define MEM_CDR_THR_MASK GENMASK(15, 13) +#define MEM_CDR_THR_SHIFT 13 +#define MEM_CDR_THR_MODE BIT(12) +#define MEM_CDR_CDR_2NDO_SDM_MODE BIT(11) +#define MEM_OVRD_HS_RATE BIT(26) + +#define PCIEPHYRX_EQUALIZER 0x00000038 +#define MEM_EQLEV GENMASK(31, 16) +#define MEM_EQFTC GENMASK(15, 11) +#define MEM_EQCTL GENMASK(10, 7) +#define MEM_EQCTL_SHIFT 7 +#define MEM_OVRD_EQLEV BIT(2) +#define MEM_OVRD_EQFTC BIT(1) + /* * This is an Empirical value that works, need to confirm the actual * value required for the PIPE3PHY_PLL_CONFIGURATION2.PLL_IDLE status @@ -91,6 +125,8 @@ struct pipe3_dpll_map { struct ti_pipe3 { void __iomem *pll_ctrl_base; + void __iomem *phy_rx; + void __iomem *phy_tx; struct device *dev; struct device *control_dev; struct clk *wkupclk; @@ -261,6 +297,37 @@ static int ti_pipe3_dpll_program(struct ti_pipe3 *phy) return ti_pipe3_dpll_wait_lock(phy); } +static void ti_pipe3_calibrate(struct ti_pipe3 *phy) +{ + u32 val; + + val = ti_pipe3_readl(phy->phy_rx, PCIEPHYRX_ANA_PROGRAMMABILITY); + val &= ~(INTERFACE_MASK | LOSD_MASK | MEM_PLLDIV); + val = (0x1 << INTERFACE_SHIFT | 0xA << LOSD_SHIFT); + ti_pipe3_writel(phy->phy_rx, PCIEPHYRX_ANA_PROGRAMMABILITY, val); + + val = ti_pipe3_readl(phy->phy_rx, PCIEPHYRX_DIGITAL_MODES); + val &= ~(MEM_CDR_STEPCNT | MEM_CDR_STL_MASK | MEM_CDR_THR_MASK | + MEM_CDR_CDR_2NDO_SDM_MODE | MEM_OVRD_HS_RATE); + val |= (MEM_CDR_FASTLOCK | MEM_CDR_LBW | 0x3 << MEM_CDR_STL_SHIFT | + 0x1 << MEM_CDR_THR_SHIFT | MEM_CDR_THR_MODE); + ti_pipe3_writel(phy->phy_rx, PCIEPHYRX_DIGITAL_MODES, val); + + val = ti_pipe3_readl(phy->phy_rx, PCIEPHYRX_TRIM); + val &= ~MEM_DLL_TRIM_SEL; + val |= 0x2 << MEM_DLL_TRIM_SHIFT; + ti_pipe3_writel(phy->phy_rx, PCIEPHYRX_TRIM, val); + + val = ti_pipe3_readl(phy->phy_rx, PCIEPHYRX_DLL); + val |= MEM_DLL_PHINT_RATE; + ti_pipe3_writel(phy->phy_rx, PCIEPHYRX_DLL, val); + + val = ti_pipe3_readl(phy->phy_rx, PCIEPHYRX_EQUALIZER); + val &= ~(MEM_EQLEV | MEM_EQCTL | MEM_OVRD_EQLEV | MEM_OVRD_EQFTC); + val |= MEM_EQFTC | 0x1 << MEM_EQCTL_SHIFT; + ti_pipe3_writel(phy->phy_rx, PCIEPHYRX_EQUALIZER, val); +} + static int ti_pipe3_init(struct phy *x) { struct ti_pipe3 *phy = phy_get_drvdata(x); @@ -282,7 +349,12 @@ static int ti_pipe3_init(struct phy *x) val = 0x96 << OMAP_CTRL_PCIE_PCS_DELAY_COUNT_SHIFT; ret = regmap_update_bits(phy->pcs_syscon, phy->pcie_pcs_reg, PCIE_PCS_MASK, val); - return ret; + if (ret) + return ret; + + ti_pipe3_calibrate(phy); + + return 0; } /* Bring it out of IDLE if it is IDLE */ @@ -513,6 +585,29 @@ static int ti_pipe3_get_sysctrl(struct ti_pipe3 *phy) return 0; } +static int ti_pipe3_get_tx_rx_base(struct ti_pipe3 *phy) +{ + struct resource *res; + struct device *dev = phy->dev; + struct device_node *node = dev->of_node; + struct platform_device *pdev = to_platform_device(dev); + + if (!of_device_is_compatible(node, "ti,phy-pipe3-pcie")) + return 0; + + res = platform_get_resource_byname(pdev, IORESOURCE_MEM, + "phy_rx"); + phy->phy_rx = devm_ioremap_resource(dev, res); + if (IS_ERR(phy->phy_rx)) + return PTR_ERR(phy->phy_rx); + + res = platform_get_resource_byname(pdev, IORESOURCE_MEM, + "phy_tx"); + phy->phy_tx = devm_ioremap_resource(dev, res); + + return PTR_ERR_OR_ZERO(phy->phy_tx); +} + static int ti_pipe3_get_pll_base(struct ti_pipe3 *phy) { struct resource *res; @@ -559,6 +654,10 @@ static int ti_pipe3_probe(struct platform_device *pdev) if (ret) return ret; + ret = ti_pipe3_get_tx_rx_base(phy); + if (ret) + return ret; + ret = ti_pipe3_get_sysctrl(phy); if (ret) return ret; -- 2.11.0
WARNING: multiple messages have this Message-ID (diff)
From: Kishon Vijay Abraham I <kishon@ti.com> To: Kishon Vijay Abraham I <kishon@ti.com>, Bjorn Helgaas <bhelgaas@google.com> Cc: Roger Quadros <rogerq@ti.com>, linux-omap@vger.kernel.org, linux-pci@vger.kernel.org, linux-kernel@vger.kernel.org, nsekhar@ti.com, Vignesh R <vigneshr@ti.com> Subject: [PATCH 2/2] phy: ti-pipe3: Update pcie phy settings Date: Mon, 9 Oct 2017 14:33:38 +0530 [thread overview] Message-ID: <20171009090338.26033-3-kishon@ti.com> (raw) In-Reply-To: <20171009090338.26033-1-kishon@ti.com> Update the PCIe phy settings based on new settings available in AM572x Technical Reference Manual[1] Revision I, revised April 2017 in Table 26-62 "Preferred PCIe_PHY_RX SCP Register Settings". [1] http://www.ti.com/lit/ug/spruhz6i/spruhz6i.pdf Cc: Vignesh R <vigneshr@ti.com> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> [nsekhar@ti.com: commit message updates] Signed-off-by: Sekhar Nori <nsekhar@ti.com> --- drivers/phy/ti/phy-ti-pipe3.c | 101 +++++++++++++++++++++++++++++++++++++++++- 1 file changed, 100 insertions(+), 1 deletion(-) diff --git a/drivers/phy/ti/phy-ti-pipe3.c b/drivers/phy/ti/phy-ti-pipe3.c index 0e564f32749f..68ce4a082b9b 100644 --- a/drivers/phy/ti/phy-ti-pipe3.c +++ b/drivers/phy/ti/phy-ti-pipe3.c @@ -68,6 +68,40 @@ #define PCIE_PCS_MASK 0xFF0000 #define PCIE_PCS_DELAY_COUNT_SHIFT 0x10 +#define PCIEPHYRX_ANA_PROGRAMMABILITY 0x0000000C +#define INTERFACE_MASK GENMASK(31, 27) +#define INTERFACE_SHIFT 27 +#define LOSD_MASK GENMASK(17, 14) +#define LOSD_SHIFT 14 +#define MEM_PLLDIV GENMASK(6, 5) + +#define PCIEPHYRX_TRIM 0x0000001C +#define MEM_DLL_TRIM_SEL GENMASK(31, 30) +#define MEM_DLL_TRIM_SHIFT 30 + +#define PCIEPHYRX_DLL 0x00000024 +#define MEM_DLL_PHINT_RATE GENMASK(31, 30) + +#define PCIEPHYRX_DIGITAL_MODES 0x00000028 +#define MEM_CDR_FASTLOCK BIT(23) +#define MEM_CDR_LBW GENMASK(22, 21) +#define MEM_CDR_STEPCNT GENMASK(20, 19) +#define MEM_CDR_STL_MASK GENMASK(18, 16) +#define MEM_CDR_STL_SHIFT 16 +#define MEM_CDR_THR_MASK GENMASK(15, 13) +#define MEM_CDR_THR_SHIFT 13 +#define MEM_CDR_THR_MODE BIT(12) +#define MEM_CDR_CDR_2NDO_SDM_MODE BIT(11) +#define MEM_OVRD_HS_RATE BIT(26) + +#define PCIEPHYRX_EQUALIZER 0x00000038 +#define MEM_EQLEV GENMASK(31, 16) +#define MEM_EQFTC GENMASK(15, 11) +#define MEM_EQCTL GENMASK(10, 7) +#define MEM_EQCTL_SHIFT 7 +#define MEM_OVRD_EQLEV BIT(2) +#define MEM_OVRD_EQFTC BIT(1) + /* * This is an Empirical value that works, need to confirm the actual * value required for the PIPE3PHY_PLL_CONFIGURATION2.PLL_IDLE status @@ -91,6 +125,8 @@ struct pipe3_dpll_map { struct ti_pipe3 { void __iomem *pll_ctrl_base; + void __iomem *phy_rx; + void __iomem *phy_tx; struct device *dev; struct device *control_dev; struct clk *wkupclk; @@ -261,6 +297,37 @@ static int ti_pipe3_dpll_program(struct ti_pipe3 *phy) return ti_pipe3_dpll_wait_lock(phy); } +static void ti_pipe3_calibrate(struct ti_pipe3 *phy) +{ + u32 val; + + val = ti_pipe3_readl(phy->phy_rx, PCIEPHYRX_ANA_PROGRAMMABILITY); + val &= ~(INTERFACE_MASK | LOSD_MASK | MEM_PLLDIV); + val = (0x1 << INTERFACE_SHIFT | 0xA << LOSD_SHIFT); + ti_pipe3_writel(phy->phy_rx, PCIEPHYRX_ANA_PROGRAMMABILITY, val); + + val = ti_pipe3_readl(phy->phy_rx, PCIEPHYRX_DIGITAL_MODES); + val &= ~(MEM_CDR_STEPCNT | MEM_CDR_STL_MASK | MEM_CDR_THR_MASK | + MEM_CDR_CDR_2NDO_SDM_MODE | MEM_OVRD_HS_RATE); + val |= (MEM_CDR_FASTLOCK | MEM_CDR_LBW | 0x3 << MEM_CDR_STL_SHIFT | + 0x1 << MEM_CDR_THR_SHIFT | MEM_CDR_THR_MODE); + ti_pipe3_writel(phy->phy_rx, PCIEPHYRX_DIGITAL_MODES, val); + + val = ti_pipe3_readl(phy->phy_rx, PCIEPHYRX_TRIM); + val &= ~MEM_DLL_TRIM_SEL; + val |= 0x2 << MEM_DLL_TRIM_SHIFT; + ti_pipe3_writel(phy->phy_rx, PCIEPHYRX_TRIM, val); + + val = ti_pipe3_readl(phy->phy_rx, PCIEPHYRX_DLL); + val |= MEM_DLL_PHINT_RATE; + ti_pipe3_writel(phy->phy_rx, PCIEPHYRX_DLL, val); + + val = ti_pipe3_readl(phy->phy_rx, PCIEPHYRX_EQUALIZER); + val &= ~(MEM_EQLEV | MEM_EQCTL | MEM_OVRD_EQLEV | MEM_OVRD_EQFTC); + val |= MEM_EQFTC | 0x1 << MEM_EQCTL_SHIFT; + ti_pipe3_writel(phy->phy_rx, PCIEPHYRX_EQUALIZER, val); +} + static int ti_pipe3_init(struct phy *x) { struct ti_pipe3 *phy = phy_get_drvdata(x); @@ -282,7 +349,12 @@ static int ti_pipe3_init(struct phy *x) val = 0x96 << OMAP_CTRL_PCIE_PCS_DELAY_COUNT_SHIFT; ret = regmap_update_bits(phy->pcs_syscon, phy->pcie_pcs_reg, PCIE_PCS_MASK, val); - return ret; + if (ret) + return ret; + + ti_pipe3_calibrate(phy); + + return 0; } /* Bring it out of IDLE if it is IDLE */ @@ -513,6 +585,29 @@ static int ti_pipe3_get_sysctrl(struct ti_pipe3 *phy) return 0; } +static int ti_pipe3_get_tx_rx_base(struct ti_pipe3 *phy) +{ + struct resource *res; + struct device *dev = phy->dev; + struct device_node *node = dev->of_node; + struct platform_device *pdev = to_platform_device(dev); + + if (!of_device_is_compatible(node, "ti,phy-pipe3-pcie")) + return 0; + + res = platform_get_resource_byname(pdev, IORESOURCE_MEM, + "phy_rx"); + phy->phy_rx = devm_ioremap_resource(dev, res); + if (IS_ERR(phy->phy_rx)) + return PTR_ERR(phy->phy_rx); + + res = platform_get_resource_byname(pdev, IORESOURCE_MEM, + "phy_tx"); + phy->phy_tx = devm_ioremap_resource(dev, res); + + return PTR_ERR_OR_ZERO(phy->phy_tx); +} + static int ti_pipe3_get_pll_base(struct ti_pipe3 *phy) { struct resource *res; @@ -559,6 +654,10 @@ static int ti_pipe3_probe(struct platform_device *pdev) if (ret) return ret; + ret = ti_pipe3_get_tx_rx_base(phy); + if (ret) + return ret; + ret = ti_pipe3_get_sysctrl(phy); if (ret) return ret; -- 2.11.0
next prev parent reply other threads:[~2017-10-09 9:03 UTC|newest] Thread overview: 21+ messages / expand[flat|nested] mbox.gz Atom feed top 2017-10-09 9:03 [PATCH 0/2] phy: ti-pipe3: Update PCIe PHY settings Kishon Vijay Abraham I 2017-10-09 9:03 ` Kishon Vijay Abraham I 2017-10-09 9:03 ` [PATCH 1/2] PCI: dwc: dra7xx: Create functional dependency between PCIe and PHY Kishon Vijay Abraham I 2017-10-09 9:03 ` Kishon Vijay Abraham I 2017-10-10 7:19 ` Roger Quadros 2017-10-10 7:19 ` Roger Quadros 2017-10-10 7:19 ` Roger Quadros 2017-10-10 7:42 ` Kishon Vijay Abraham I 2017-10-10 7:42 ` Kishon Vijay Abraham I 2017-10-10 7:59 ` Roger Quadros 2017-10-10 7:59 ` Roger Quadros 2017-10-10 7:59 ` Roger Quadros 2017-10-18 12:12 ` Kishon Vijay Abraham I 2017-10-18 12:12 ` Kishon Vijay Abraham I 2017-10-19 9:46 ` Roger Quadros 2017-10-19 9:46 ` Roger Quadros 2017-10-09 9:03 ` Kishon Vijay Abraham I [this message] 2017-10-09 9:03 ` [PATCH 2/2] phy: ti-pipe3: Update pcie phy settings Kishon Vijay Abraham I 2017-10-17 19:31 ` [PATCH 0/2] phy: ti-pipe3: Update PCIe PHY settings Bjorn Helgaas 2017-10-18 12:08 ` Kishon Vijay Abraham I 2017-10-18 12:08 ` Kishon Vijay Abraham I
Reply instructions: You may reply publicly to this message via plain-text email using any one of the following methods: * Save the following mbox file, import it into your mail client, and reply-to-all from there: mbox Avoid top-posting and favor interleaved quoting: https://en.wikipedia.org/wiki/Posting_style#Interleaved_style * Reply using the --to, --cc, and --in-reply-to switches of git-send-email(1): git send-email \ --in-reply-to=20171009090338.26033-3-kishon@ti.com \ --to=kishon@ti.com \ --cc=bhelgaas@google.com \ --cc=linux-kernel@vger.kernel.org \ --cc=linux-omap@vger.kernel.org \ --cc=linux-pci@vger.kernel.org \ --cc=nsekhar@ti.com \ --cc=rogerq@ti.com \ --cc=vigneshr@ti.com \ /path/to/YOUR_REPLY https://kernel.org/pub/software/scm/git/docs/git-send-email.html * If your mail client supports setting the In-Reply-To header via mailto: links, try the mailto: linkBe sure your reply has a Subject: header at the top and a blank line before the message body.
This is an external index of several public inboxes, see mirroring instructions on how to clone and mirror all data and code used by this external index.