[PULL 02/26] arm64: Use physical counter for in-kernel reads when booted in EL2

[Christoffer Dall <christoffer.dall@linaro.org>]

From: Christoffer Dall <cdall@linaro.org>

Using the physical counter allows KVM to retain the offset between the
virtual and physical counter as long as it is actively running a VCPU.

As soon as a VCPU is released, another thread is scheduled or we start
running userspace applications, we reset the offset to 0, so that
userspace accessing the virtual timer can still read the virtual counter
and get the same view of time as the kernel.

This opens up potential improvements for KVM performance, but we have to
make a few adjustments to preserve system consistency.

Currently get_cycles() is hardwired to arch_counter_get_cntvct() on
arm64, but as we move to using the physical timer for the in-kernel
time-keeping on systems that boot in EL2, we should use the same counter
for get_cycles() as for other in-kernel timekeeping operations.

Similarly, implementations of arch_timer_set_next_event_phys() is
modified to use the counter specific to the timer being programmed.

VHE kernels or kernels continuing to use the virtual timer are
unaffected.

Cc: Will Deacon <will.deacon@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <cdall@linaro.org>
---
 arch/arm64/include/asm/timex.h       |  2 +-
 drivers/clocksource/arm_arch_timer.c | 12 ++++++++----
 2 files changed, 9 insertions(+), 5 deletions(-)

diff --git a/arch/arm64/include/asm/timex.h b/arch/arm64/include/asm/timex.h
index 81a076eb37fa..9ad60bae5c8d 100644
--- a/arch/arm64/include/asm/timex.h
+++ b/arch/arm64/include/asm/timex.h
@@ -22,7 +22,7 @@
  * Use the current timer as a cycle counter since this is what we use for
  * the delay loop.
  */
-#define get_cycles()	arch_counter_get_cntvct()
+#define get_cycles()	arch_timer_read_counter()
 
 #include <asm-generic/timex.h>
 
diff --git a/drivers/clocksource/arm_arch_timer.c b/drivers/clocksource/arm_arch_timer.c
index ff8f8a177156..061476e92db7 100644
--- a/drivers/clocksource/arm_arch_timer.c
+++ b/drivers/clocksource/arm_arch_timer.c
@@ -158,6 +158,7 @@ u32 arch_timer_reg_read(int access, enum arch_timer_reg reg,
  * if we don't have the cp15 accessors we won't have a problem.
  */
 u64 (*arch_timer_read_counter)(void) = arch_counter_get_cntvct;
+EXPORT_SYMBOL_GPL(arch_timer_read_counter);
 
 static u64 arch_counter_read(struct clocksource *cs)
 {
@@ -329,16 +330,19 @@ static void erratum_set_next_event_tval_generic(const int access, unsigned long
 						struct clock_event_device *clk)
 {
 	unsigned long ctrl;
-	u64 cval = evt + arch_counter_get_cntvct();
+	u64 cval;
 
 	ctrl = arch_timer_reg_read(access, ARCH_TIMER_REG_CTRL, clk);
 	ctrl |= ARCH_TIMER_CTRL_ENABLE;
 	ctrl &= ~ARCH_TIMER_CTRL_IT_MASK;
 
-	if (access == ARCH_TIMER_PHYS_ACCESS)
+	if (access == ARCH_TIMER_PHYS_ACCESS) {
+		cval = evt + arch_counter_get_cntpct();
 		write_sysreg(cval, cntp_cval_el0);
-	else
+	} else {
+		cval = evt + arch_counter_get_cntvct();
 		write_sysreg(cval, cntv_cval_el0);
+	}
 
 	arch_timer_reg_write(access, ARCH_TIMER_REG_CTRL, ctrl, clk);
 }
@@ -913,7 +917,7 @@ static void __init arch_counter_register(unsigned type)
 
 	/* Register the CP15 based counter if we have one */
 	if (type & ARCH_TIMER_TYPE_CP15) {
-		if (IS_ENABLED(CONFIG_ARM64) ||
+		if ((IS_ENABLED(CONFIG_ARM64) && !is_hyp_mode_available()) ||
 		    arch_timer_uses_ppi == ARCH_TIMER_VIRT_PPI)
 			arch_timer_read_counter = arch_counter_get_cntvct;
 		else
-- 
2.14.2