From: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
To: linus.walleij@linaro.org, robh+dt@kernel.org, afaerber@suse.de
Cc: devicetree@vger.kernel.org, daniel.thompson@linaro.org,
hzhang@ucrobotics.com, bdong@ucrobotics.com,
liuwei@actions-semi.com, linux-kernel@vger.kernel.org,
amit.kucheria@linaro.org, linux-gpio@vger.kernel.org,
mp-cs@actions-semi.com, 96boards@ucrobotics.com,
Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>,
linux-arm-kernel@lists.infradead.org
Subject: [PATCH v2 07/10] arm64: dts: actions: Add gpio line names to Bubblegum-96 board
Date: Wed, 21 Feb 2018 21:30:41 +0530 [thread overview]
Message-ID: <20180221160044.15089-8-manivannan.sadhasivam@linaro.org> (raw)
In-Reply-To: <20180221160044.15089-1-manivannan.sadhasivam@linaro.org>
Add gpio line names to Actions Semi S900 based Bubblegum-96 board.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
---
arch/arm64/boot/dts/actions/s900-bubblegum-96.dts | 195 ++++++++++++++++++++++
1 file changed, 195 insertions(+)
diff --git a/arch/arm64/boot/dts/actions/s900-bubblegum-96.dts b/arch/arm64/boot/dts/actions/s900-bubblegum-96.dts
index 60ddaf98401b..05ec8a7e924d 100644
--- a/arch/arm64/boot/dts/actions/s900-bubblegum-96.dts
+++ b/arch/arm64/boot/dts/actions/s900-bubblegum-96.dts
@@ -40,3 +40,198 @@
status = "okay";
clocks = <&cmu CLK_UART5>;
};
+
+/*
+ * GPIO name legend: proper name = the GPIO line is used as GPIO
+ * NC = not connected (pin out but not routed from the chip to
+ * anything the board)
+ * "[PER]" = pin is muxed for [peripheral] (not GPIO)
+ * LSEC = Low Speed External Connector
+ * HSEC = High Speed External Connector
+ *
+ * Line names are taken from the schematic "Schematics Bubblegum96"
+ * version v1.0
+ *
+ * For the lines routed to the external connectors the
+ * lines are named after the 96Boards CE Specification 1.0,
+ * Appendix "Expansion Connector Signal Description".
+ *
+ * When the 96Boards naming of a line and the schematic name of
+ * the same line are in conflict, the 96Boards specification
+ * takes precedence, which means that the external UART on the
+ * LSEC is named UART0 while the schematic and SoC names this
+ * UART2. Only exception is the I2C lines for which the schematic
+ * naming has been preferred. This is only for the informational
+ * lines i.e. "[FOO]", the GPIO named lines "GPIO-A" thru "GPIO-L"
+ * are the only ones actually used for GPIO.
+ */
+
+&gpioa {
+ gpio-line-names =
+ "GPIO-A", /* GPIO_0, LSEC pin 23 */
+ "GPIO-B", /* GPIO_1, LSEC pin 24 */
+ "GPIO-C", /* GPIO_2, LSEC pin 25 */
+ "GPIO-D", /* GPIO_3, LSEC pin 26 */
+ "GPIO-E", /* GPIO_4, LSEC pin 27 */
+ "GPIO-F", /* GPIO_5, LSEC pin 28 */
+ "GPIO-G", /* GPIO_6, LSEC pin 29 */
+ "GPIO-H", /* GPIO_7, LSEC pin 30 */
+ "GPIO-I", /* GPIO_8, LSEC pin 31 */
+ "GPIO-J", /* GPIO_9, LSEC pin 32 */
+ "NC", /* GPIO_10 */
+ "NC", /* GPIO_11 */
+ "SIRQ2_1V8", /* GPIO_12 */
+ "PCM0_OUT", /* GPIO_13 */
+ "WIFI_LED", /* GPIO_14 */
+ "PCM0_SYNC", /* GPIO_15 */
+ "PCM0_CLK", /* GPIO_16 */
+ "PCM0_IN", /* GPIO_17 */
+ "BT_LED", /* GPIO_18 */
+ "LED0", /* GPIO_19 */
+ "LED1", /* GPIO_20 */
+ "JTAG_TCK", /* GPIO_21 */
+ "JTAG_TMS", /* GPIO_22 */
+ "JTAG_TDI", /* GPIO_23 */
+ "JTAG_TDO", /* GPIO_24 */
+ "[UART1_RxD]", /* GPIO_25, LSEC pin 13 */
+ "NC", /* GPIO_26 */
+ "[UART1_TxD]", /* GPIO_27, LSEC pin 11 */
+ "SD0_D0", /* GPIO_28 */
+ "SD0_D1", /* GPIO_29 */
+ "SD0_D2", /* GPIO_30 */
+ "SD0_D3"; /* GPIO_31 */
+};
+
+&gpiob {
+ gpio-line-names =
+ "SD1_D0", /* GPIO_32 */
+ "SD1_D1", /* GPIO_33 */
+ "SD1_D2", /* GPIO_34 */
+ "SD1_D3", /* GPIO_35 */
+ "SD0_CMD", /* GPIO_36 */
+ "SD0_CLK", /* GPIO_37 */
+ "SD1_CMD", /* GPIO_38 */
+ "SD1_CLK", /* GPIO_39 */
+ "SPI0_SCLK", /* GPIO_40, LSEC pin 8 */
+ "SPI0_CS", /* GPIO_41, LSEC pin 12 */
+ "SPI0_DIN", /* GPIO_42, LSEC pin 10 */
+ "SPI0_DOUT", /* GPIO_43, LSEC pin 14 */
+ "I2C5_SDATA", /* GPIO_44, HSEC pin 36 */
+ "I2C5_SCLK", /* GPIO_45, HSEC pin 38 */
+ "UART0_RX", /* GPIO_46, LSEC pin 7 */
+ "UART0_TX", /* GPIO_47, LSEC pin 5 */
+ "UART0_RTSB", /* GPIO_48, LSEC pin 9 */
+ "UART0_CTSB", /* GPIO_49, LSEC pin 3 */
+ "I2C4_SCLK", /* GPIO_50, HSEC pin 32 */
+ "I2C4_SDATA", /* GPIO_51, HSEC pin 34 */
+ "I2C0_SCLK", /* GPIO_52 */
+ "I2C0_SDATA", /* GPIO_53 */
+ "I2C1_SCLK", /* GPIO_54, LSEC pin 15 */
+ "I2C1_SDATA", /* GPIO_55, LSEC pin 17 */
+ "I2C2_SCLK", /* GPIO_56, LSEC pin 19 */
+ "I2C2_SDATA", /* GPIO_57, LSEC pin 21 */
+ "CSI0_DN0", /* GPIO_58, HSEC pin 10 */
+ "CSI0_DP0", /* GPIO_59, HSEC pin 8 */
+ "CSI0_DN1", /* GPIO_60, HSEC pin 16 */
+ "CSI0_DP1", /* GPIO_61, HSEC pin 14 */
+ "CSI0_CN", /* GPIO_62, HSEC pin 4 */
+ "CSI0_CP"; /* GPIO_63, HSEC pin 2 */
+};
+
+&gpioc {
+ gpio-line-names =
+ "CSI0_DN2", /* GPIO_64, HSEC pin 22 */
+ "CSI0_DP2", /* GPIO_65, HSEC pin 20 */
+ "CSI0_DN3", /* GPIO_66, HSEC pin 28 */
+ "CSI0_DP3", /* GPIO_67, HSEC pin 26 */
+ "[CLK0]", /* GPIO_68, HSEC pin 15 */
+ "CSI1_DN0", /* GPIO_69, HSEC pin 44 */
+ "CSI1_DP0", /* GPIO_70, HSEC pin 42 */
+ "CSI1_DN1", /* GPIO_71, HSEC pin 50 */
+ "CSI1_DP1", /* GPIO_72, HSEC pin 48 */
+ "CSI1_CN", /* GPIO_73, HSEC pin 56 */
+ "CSI1_CP", /* GPIO_74, HSEC pin 54 */
+ "[CLK1]"; /* GPIO_75, HSEC pin 17 */
+};
+
+&gpiod {
+ gpio-line-names =
+ "[GPIOD0]", /* GPIO_76 */
+ "[GPIOD1]", /* GPIO_77 */
+ "BT_RST_N", /* GPIO_78 */
+ "EXT_DC_EN", /* GPIO_79 */
+ "[PCM_DI]", /* GPIO_80, LSEC pin 22 */
+ "[PCM_DO]", /* GPIO_81, LSEC pin 20 */
+ "[PCM_CLK]", /* GPIO_82, LSEC pin 18 */
+ "[PCM_FS]", /* GPIO_83, LSEC pin 16 */
+ "WAKE_BT", /* GPIO_84 */
+ "WL_REG_ON", /* GPIO_85 */
+ "NC", /* GPIO_86 */
+ "NC", /* GPIO_87 */
+ "NC", /* GPIO_88 */
+ "NC", /* GPIO_89 */
+ "NC", /* GPIO_90 */
+ "WIFI_WAKE", /* GPIO_91 */
+ "BT_WAKE", /* GPIO_92 */
+ "NC", /* GPIO_93 */
+ "OTG_EN2", /* GPIO_94 */
+ "OTG_EN", /* GPIO_95 */
+ "DSI_DP3", /* GPIO_96, HSEC pin 45 */
+ "DSI_DN3", /* GPIO_97, HSEC pin 47 */
+ "DSI_DP1", /* GPIO_98, HSEC pin 33 */
+ "DSI_DN1", /* GPIO_99, HSEC pin 35 */
+ "DSI_CP", /* GPIO_100, HSEC pin 21 */
+ "DSI_CN", /* GPIO_101, HSEC pin 23 */
+ "DSI_DP0", /* GPIO_102, HSEC pin 27 */
+ "DSI_DN0", /* GPIO_103, HSEC pin 29 */
+ "DSI_DP2", /* GPIO_104, HSEC pin 39 */
+ "DSI_DN2"; /* GPIO_105, HSEC pin 41 */
+};
+
+&gpioe {
+ gpio-line-names =
+ "N0_D0", /* GPIO_106 */
+ "N0_D1", /* GPIO_107 */
+ "N0_D2", /* GPIO_108 */
+ "N0_D3", /* GPIO_109 */
+ "N0_D4", /* GPIO_110 */
+ "N0_D5", /* GPIO_111 */
+ "N0_D6", /* GPIO_112 */
+ "N0_D7", /* GPIO_113 */
+ "N0_DQS", /* GPIO_114 */
+ "N0_DQSN", /* GPIO_115 */
+ "NC", /* GPIO_116 */
+ "NC", /* GPIO_117 */
+ "NC", /* GPIO_118 */
+ "N0_CEB1", /* GPIO_119 */
+ "CARD_DT", /* GPIO_120 */
+ "N0_CEB3", /* GPIO_121 */
+ "SD_DAT0", /* GPIO_122, HSEC pin 1 */
+ "SD_DAT1", /* GPIO_123, HSEC pin 3 */
+ "SD_DAT2", /* GPIO_124, HSEC pin 5 */
+ "SD_DAT3", /* GPIO_125, HSEC pin 7 */
+ "NC", /* GPIO_126 */
+ "NC", /* GPIO_127 */
+ "[PWR_BTN_N]", /* GPIO_128, LSEC pin 4 */
+ "[RST_BTN_N]", /* GPIO_129, LSEC pin 6 */
+ "NC", /* GPIO_130 */
+ "SD_CMD", /* GPIO_131 */
+ "GPIO-L", /* GPIO_132, LSEC pin 34 */
+ "GPIO-K", /* GPIO_133, LSEC pin 33 */
+ "NC", /* GPIO_134 */
+ "SD_SCLK", /* GPIO_135 */
+ "NC", /* GPIO_136 */
+ "JTAG_TRST"; /* GPIO_137 */
+};
+
+&gpiof {
+ gpio-line-names =
+ "I2C3_SCLK", /* GPIO_138 */
+ "LED2", /* GPIO_139 */
+ "LED3", /* GPIO_140 */
+ "I2C3_SDATA", /* GPIO_141 */
+ "UART3_RX", /* GPIO_142 */
+ "UART3_TX", /* GPIO_143 */
+ "UART3_RTSB", /* GPIO_144 */
+ "UART3_CTSB"; /* GPIO_145 */
+};
--
2.14.1
WARNING: multiple messages have this Message-ID (diff)
From: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
To: linus.walleij@linaro.org, robh+dt@kernel.org, afaerber@suse.de
Cc: liuwei@actions-semi.com, mp-cs@actions-semi.com,
96boards@ucrobotics.com, devicetree@vger.kernel.org,
daniel.thompson@linaro.org, amit.kucheria@linaro.org,
linux-arm-kernel@lists.infradead.org, linux-gpio@vger.kernel.org,
linux-kernel@vger.kernel.org, hzhang@ucrobotics.com,
bdong@ucrobotics.com,
Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Subject: [PATCH v2 07/10] arm64: dts: actions: Add gpio line names to Bubblegum-96 board
Date: Wed, 21 Feb 2018 21:30:41 +0530 [thread overview]
Message-ID: <20180221160044.15089-8-manivannan.sadhasivam@linaro.org> (raw)
In-Reply-To: <20180221160044.15089-1-manivannan.sadhasivam@linaro.org>
Add gpio line names to Actions Semi S900 based Bubblegum-96 board.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
---
arch/arm64/boot/dts/actions/s900-bubblegum-96.dts | 195 ++++++++++++++++++++++
1 file changed, 195 insertions(+)
diff --git a/arch/arm64/boot/dts/actions/s900-bubblegum-96.dts b/arch/arm64/boot/dts/actions/s900-bubblegum-96.dts
index 60ddaf98401b..05ec8a7e924d 100644
--- a/arch/arm64/boot/dts/actions/s900-bubblegum-96.dts
+++ b/arch/arm64/boot/dts/actions/s900-bubblegum-96.dts
@@ -40,3 +40,198 @@
status = "okay";
clocks = <&cmu CLK_UART5>;
};
+
+/*
+ * GPIO name legend: proper name = the GPIO line is used as GPIO
+ * NC = not connected (pin out but not routed from the chip to
+ * anything the board)
+ * "[PER]" = pin is muxed for [peripheral] (not GPIO)
+ * LSEC = Low Speed External Connector
+ * HSEC = High Speed External Connector
+ *
+ * Line names are taken from the schematic "Schematics Bubblegum96"
+ * version v1.0
+ *
+ * For the lines routed to the external connectors the
+ * lines are named after the 96Boards CE Specification 1.0,
+ * Appendix "Expansion Connector Signal Description".
+ *
+ * When the 96Boards naming of a line and the schematic name of
+ * the same line are in conflict, the 96Boards specification
+ * takes precedence, which means that the external UART on the
+ * LSEC is named UART0 while the schematic and SoC names this
+ * UART2. Only exception is the I2C lines for which the schematic
+ * naming has been preferred. This is only for the informational
+ * lines i.e. "[FOO]", the GPIO named lines "GPIO-A" thru "GPIO-L"
+ * are the only ones actually used for GPIO.
+ */
+
+&gpioa {
+ gpio-line-names =
+ "GPIO-A", /* GPIO_0, LSEC pin 23 */
+ "GPIO-B", /* GPIO_1, LSEC pin 24 */
+ "GPIO-C", /* GPIO_2, LSEC pin 25 */
+ "GPIO-D", /* GPIO_3, LSEC pin 26 */
+ "GPIO-E", /* GPIO_4, LSEC pin 27 */
+ "GPIO-F", /* GPIO_5, LSEC pin 28 */
+ "GPIO-G", /* GPIO_6, LSEC pin 29 */
+ "GPIO-H", /* GPIO_7, LSEC pin 30 */
+ "GPIO-I", /* GPIO_8, LSEC pin 31 */
+ "GPIO-J", /* GPIO_9, LSEC pin 32 */
+ "NC", /* GPIO_10 */
+ "NC", /* GPIO_11 */
+ "SIRQ2_1V8", /* GPIO_12 */
+ "PCM0_OUT", /* GPIO_13 */
+ "WIFI_LED", /* GPIO_14 */
+ "PCM0_SYNC", /* GPIO_15 */
+ "PCM0_CLK", /* GPIO_16 */
+ "PCM0_IN", /* GPIO_17 */
+ "BT_LED", /* GPIO_18 */
+ "LED0", /* GPIO_19 */
+ "LED1", /* GPIO_20 */
+ "JTAG_TCK", /* GPIO_21 */
+ "JTAG_TMS", /* GPIO_22 */
+ "JTAG_TDI", /* GPIO_23 */
+ "JTAG_TDO", /* GPIO_24 */
+ "[UART1_RxD]", /* GPIO_25, LSEC pin 13 */
+ "NC", /* GPIO_26 */
+ "[UART1_TxD]", /* GPIO_27, LSEC pin 11 */
+ "SD0_D0", /* GPIO_28 */
+ "SD0_D1", /* GPIO_29 */
+ "SD0_D2", /* GPIO_30 */
+ "SD0_D3"; /* GPIO_31 */
+};
+
+&gpiob {
+ gpio-line-names =
+ "SD1_D0", /* GPIO_32 */
+ "SD1_D1", /* GPIO_33 */
+ "SD1_D2", /* GPIO_34 */
+ "SD1_D3", /* GPIO_35 */
+ "SD0_CMD", /* GPIO_36 */
+ "SD0_CLK", /* GPIO_37 */
+ "SD1_CMD", /* GPIO_38 */
+ "SD1_CLK", /* GPIO_39 */
+ "SPI0_SCLK", /* GPIO_40, LSEC pin 8 */
+ "SPI0_CS", /* GPIO_41, LSEC pin 12 */
+ "SPI0_DIN", /* GPIO_42, LSEC pin 10 */
+ "SPI0_DOUT", /* GPIO_43, LSEC pin 14 */
+ "I2C5_SDATA", /* GPIO_44, HSEC pin 36 */
+ "I2C5_SCLK", /* GPIO_45, HSEC pin 38 */
+ "UART0_RX", /* GPIO_46, LSEC pin 7 */
+ "UART0_TX", /* GPIO_47, LSEC pin 5 */
+ "UART0_RTSB", /* GPIO_48, LSEC pin 9 */
+ "UART0_CTSB", /* GPIO_49, LSEC pin 3 */
+ "I2C4_SCLK", /* GPIO_50, HSEC pin 32 */
+ "I2C4_SDATA", /* GPIO_51, HSEC pin 34 */
+ "I2C0_SCLK", /* GPIO_52 */
+ "I2C0_SDATA", /* GPIO_53 */
+ "I2C1_SCLK", /* GPIO_54, LSEC pin 15 */
+ "I2C1_SDATA", /* GPIO_55, LSEC pin 17 */
+ "I2C2_SCLK", /* GPIO_56, LSEC pin 19 */
+ "I2C2_SDATA", /* GPIO_57, LSEC pin 21 */
+ "CSI0_DN0", /* GPIO_58, HSEC pin 10 */
+ "CSI0_DP0", /* GPIO_59, HSEC pin 8 */
+ "CSI0_DN1", /* GPIO_60, HSEC pin 16 */
+ "CSI0_DP1", /* GPIO_61, HSEC pin 14 */
+ "CSI0_CN", /* GPIO_62, HSEC pin 4 */
+ "CSI0_CP"; /* GPIO_63, HSEC pin 2 */
+};
+
+&gpioc {
+ gpio-line-names =
+ "CSI0_DN2", /* GPIO_64, HSEC pin 22 */
+ "CSI0_DP2", /* GPIO_65, HSEC pin 20 */
+ "CSI0_DN3", /* GPIO_66, HSEC pin 28 */
+ "CSI0_DP3", /* GPIO_67, HSEC pin 26 */
+ "[CLK0]", /* GPIO_68, HSEC pin 15 */
+ "CSI1_DN0", /* GPIO_69, HSEC pin 44 */
+ "CSI1_DP0", /* GPIO_70, HSEC pin 42 */
+ "CSI1_DN1", /* GPIO_71, HSEC pin 50 */
+ "CSI1_DP1", /* GPIO_72, HSEC pin 48 */
+ "CSI1_CN", /* GPIO_73, HSEC pin 56 */
+ "CSI1_CP", /* GPIO_74, HSEC pin 54 */
+ "[CLK1]"; /* GPIO_75, HSEC pin 17 */
+};
+
+&gpiod {
+ gpio-line-names =
+ "[GPIOD0]", /* GPIO_76 */
+ "[GPIOD1]", /* GPIO_77 */
+ "BT_RST_N", /* GPIO_78 */
+ "EXT_DC_EN", /* GPIO_79 */
+ "[PCM_DI]", /* GPIO_80, LSEC pin 22 */
+ "[PCM_DO]", /* GPIO_81, LSEC pin 20 */
+ "[PCM_CLK]", /* GPIO_82, LSEC pin 18 */
+ "[PCM_FS]", /* GPIO_83, LSEC pin 16 */
+ "WAKE_BT", /* GPIO_84 */
+ "WL_REG_ON", /* GPIO_85 */
+ "NC", /* GPIO_86 */
+ "NC", /* GPIO_87 */
+ "NC", /* GPIO_88 */
+ "NC", /* GPIO_89 */
+ "NC", /* GPIO_90 */
+ "WIFI_WAKE", /* GPIO_91 */
+ "BT_WAKE", /* GPIO_92 */
+ "NC", /* GPIO_93 */
+ "OTG_EN2", /* GPIO_94 */
+ "OTG_EN", /* GPIO_95 */
+ "DSI_DP3", /* GPIO_96, HSEC pin 45 */
+ "DSI_DN3", /* GPIO_97, HSEC pin 47 */
+ "DSI_DP1", /* GPIO_98, HSEC pin 33 */
+ "DSI_DN1", /* GPIO_99, HSEC pin 35 */
+ "DSI_CP", /* GPIO_100, HSEC pin 21 */
+ "DSI_CN", /* GPIO_101, HSEC pin 23 */
+ "DSI_DP0", /* GPIO_102, HSEC pin 27 */
+ "DSI_DN0", /* GPIO_103, HSEC pin 29 */
+ "DSI_DP2", /* GPIO_104, HSEC pin 39 */
+ "DSI_DN2"; /* GPIO_105, HSEC pin 41 */
+};
+
+&gpioe {
+ gpio-line-names =
+ "N0_D0", /* GPIO_106 */
+ "N0_D1", /* GPIO_107 */
+ "N0_D2", /* GPIO_108 */
+ "N0_D3", /* GPIO_109 */
+ "N0_D4", /* GPIO_110 */
+ "N0_D5", /* GPIO_111 */
+ "N0_D6", /* GPIO_112 */
+ "N0_D7", /* GPIO_113 */
+ "N0_DQS", /* GPIO_114 */
+ "N0_DQSN", /* GPIO_115 */
+ "NC", /* GPIO_116 */
+ "NC", /* GPIO_117 */
+ "NC", /* GPIO_118 */
+ "N0_CEB1", /* GPIO_119 */
+ "CARD_DT", /* GPIO_120 */
+ "N0_CEB3", /* GPIO_121 */
+ "SD_DAT0", /* GPIO_122, HSEC pin 1 */
+ "SD_DAT1", /* GPIO_123, HSEC pin 3 */
+ "SD_DAT2", /* GPIO_124, HSEC pin 5 */
+ "SD_DAT3", /* GPIO_125, HSEC pin 7 */
+ "NC", /* GPIO_126 */
+ "NC", /* GPIO_127 */
+ "[PWR_BTN_N]", /* GPIO_128, LSEC pin 4 */
+ "[RST_BTN_N]", /* GPIO_129, LSEC pin 6 */
+ "NC", /* GPIO_130 */
+ "SD_CMD", /* GPIO_131 */
+ "GPIO-L", /* GPIO_132, LSEC pin 34 */
+ "GPIO-K", /* GPIO_133, LSEC pin 33 */
+ "NC", /* GPIO_134 */
+ "SD_SCLK", /* GPIO_135 */
+ "NC", /* GPIO_136 */
+ "JTAG_TRST"; /* GPIO_137 */
+};
+
+&gpiof {
+ gpio-line-names =
+ "I2C3_SCLK", /* GPIO_138 */
+ "LED2", /* GPIO_139 */
+ "LED3", /* GPIO_140 */
+ "I2C3_SDATA", /* GPIO_141 */
+ "UART3_RX", /* GPIO_142 */
+ "UART3_TX", /* GPIO_143 */
+ "UART3_RTSB", /* GPIO_144 */
+ "UART3_CTSB"; /* GPIO_145 */
+};
--
2.14.1
WARNING: multiple messages have this Message-ID (diff)
From: manivannan.sadhasivam@linaro.org (Manivannan Sadhasivam)
To: linux-arm-kernel@lists.infradead.org
Subject: [PATCH v2 07/10] arm64: dts: actions: Add gpio line names to Bubblegum-96 board
Date: Wed, 21 Feb 2018 21:30:41 +0530 [thread overview]
Message-ID: <20180221160044.15089-8-manivannan.sadhasivam@linaro.org> (raw)
In-Reply-To: <20180221160044.15089-1-manivannan.sadhasivam@linaro.org>
Add gpio line names to Actions Semi S900 based Bubblegum-96 board.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
---
arch/arm64/boot/dts/actions/s900-bubblegum-96.dts | 195 ++++++++++++++++++++++
1 file changed, 195 insertions(+)
diff --git a/arch/arm64/boot/dts/actions/s900-bubblegum-96.dts b/arch/arm64/boot/dts/actions/s900-bubblegum-96.dts
index 60ddaf98401b..05ec8a7e924d 100644
--- a/arch/arm64/boot/dts/actions/s900-bubblegum-96.dts
+++ b/arch/arm64/boot/dts/actions/s900-bubblegum-96.dts
@@ -40,3 +40,198 @@
status = "okay";
clocks = <&cmu CLK_UART5>;
};
+
+/*
+ * GPIO name legend: proper name = the GPIO line is used as GPIO
+ * NC = not connected (pin out but not routed from the chip to
+ * anything the board)
+ * "[PER]" = pin is muxed for [peripheral] (not GPIO)
+ * LSEC = Low Speed External Connector
+ * HSEC = High Speed External Connector
+ *
+ * Line names are taken from the schematic "Schematics Bubblegum96"
+ * version v1.0
+ *
+ * For the lines routed to the external connectors the
+ * lines are named after the 96Boards CE Specification 1.0,
+ * Appendix "Expansion Connector Signal Description".
+ *
+ * When the 96Boards naming of a line and the schematic name of
+ * the same line are in conflict, the 96Boards specification
+ * takes precedence, which means that the external UART on the
+ * LSEC is named UART0 while the schematic and SoC names this
+ * UART2. Only exception is the I2C lines for which the schematic
+ * naming has been preferred. This is only for the informational
+ * lines i.e. "[FOO]", the GPIO named lines "GPIO-A" thru "GPIO-L"
+ * are the only ones actually used for GPIO.
+ */
+
+&gpioa {
+ gpio-line-names =
+ "GPIO-A", /* GPIO_0, LSEC pin 23 */
+ "GPIO-B", /* GPIO_1, LSEC pin 24 */
+ "GPIO-C", /* GPIO_2, LSEC pin 25 */
+ "GPIO-D", /* GPIO_3, LSEC pin 26 */
+ "GPIO-E", /* GPIO_4, LSEC pin 27 */
+ "GPIO-F", /* GPIO_5, LSEC pin 28 */
+ "GPIO-G", /* GPIO_6, LSEC pin 29 */
+ "GPIO-H", /* GPIO_7, LSEC pin 30 */
+ "GPIO-I", /* GPIO_8, LSEC pin 31 */
+ "GPIO-J", /* GPIO_9, LSEC pin 32 */
+ "NC", /* GPIO_10 */
+ "NC", /* GPIO_11 */
+ "SIRQ2_1V8", /* GPIO_12 */
+ "PCM0_OUT", /* GPIO_13 */
+ "WIFI_LED", /* GPIO_14 */
+ "PCM0_SYNC", /* GPIO_15 */
+ "PCM0_CLK", /* GPIO_16 */
+ "PCM0_IN", /* GPIO_17 */
+ "BT_LED", /* GPIO_18 */
+ "LED0", /* GPIO_19 */
+ "LED1", /* GPIO_20 */
+ "JTAG_TCK", /* GPIO_21 */
+ "JTAG_TMS", /* GPIO_22 */
+ "JTAG_TDI", /* GPIO_23 */
+ "JTAG_TDO", /* GPIO_24 */
+ "[UART1_RxD]", /* GPIO_25, LSEC pin 13 */
+ "NC", /* GPIO_26 */
+ "[UART1_TxD]", /* GPIO_27, LSEC pin 11 */
+ "SD0_D0", /* GPIO_28 */
+ "SD0_D1", /* GPIO_29 */
+ "SD0_D2", /* GPIO_30 */
+ "SD0_D3"; /* GPIO_31 */
+};
+
+&gpiob {
+ gpio-line-names =
+ "SD1_D0", /* GPIO_32 */
+ "SD1_D1", /* GPIO_33 */
+ "SD1_D2", /* GPIO_34 */
+ "SD1_D3", /* GPIO_35 */
+ "SD0_CMD", /* GPIO_36 */
+ "SD0_CLK", /* GPIO_37 */
+ "SD1_CMD", /* GPIO_38 */
+ "SD1_CLK", /* GPIO_39 */
+ "SPI0_SCLK", /* GPIO_40, LSEC pin 8 */
+ "SPI0_CS", /* GPIO_41, LSEC pin 12 */
+ "SPI0_DIN", /* GPIO_42, LSEC pin 10 */
+ "SPI0_DOUT", /* GPIO_43, LSEC pin 14 */
+ "I2C5_SDATA", /* GPIO_44, HSEC pin 36 */
+ "I2C5_SCLK", /* GPIO_45, HSEC pin 38 */
+ "UART0_RX", /* GPIO_46, LSEC pin 7 */
+ "UART0_TX", /* GPIO_47, LSEC pin 5 */
+ "UART0_RTSB", /* GPIO_48, LSEC pin 9 */
+ "UART0_CTSB", /* GPIO_49, LSEC pin 3 */
+ "I2C4_SCLK", /* GPIO_50, HSEC pin 32 */
+ "I2C4_SDATA", /* GPIO_51, HSEC pin 34 */
+ "I2C0_SCLK", /* GPIO_52 */
+ "I2C0_SDATA", /* GPIO_53 */
+ "I2C1_SCLK", /* GPIO_54, LSEC pin 15 */
+ "I2C1_SDATA", /* GPIO_55, LSEC pin 17 */
+ "I2C2_SCLK", /* GPIO_56, LSEC pin 19 */
+ "I2C2_SDATA", /* GPIO_57, LSEC pin 21 */
+ "CSI0_DN0", /* GPIO_58, HSEC pin 10 */
+ "CSI0_DP0", /* GPIO_59, HSEC pin 8 */
+ "CSI0_DN1", /* GPIO_60, HSEC pin 16 */
+ "CSI0_DP1", /* GPIO_61, HSEC pin 14 */
+ "CSI0_CN", /* GPIO_62, HSEC pin 4 */
+ "CSI0_CP"; /* GPIO_63, HSEC pin 2 */
+};
+
+&gpioc {
+ gpio-line-names =
+ "CSI0_DN2", /* GPIO_64, HSEC pin 22 */
+ "CSI0_DP2", /* GPIO_65, HSEC pin 20 */
+ "CSI0_DN3", /* GPIO_66, HSEC pin 28 */
+ "CSI0_DP3", /* GPIO_67, HSEC pin 26 */
+ "[CLK0]", /* GPIO_68, HSEC pin 15 */
+ "CSI1_DN0", /* GPIO_69, HSEC pin 44 */
+ "CSI1_DP0", /* GPIO_70, HSEC pin 42 */
+ "CSI1_DN1", /* GPIO_71, HSEC pin 50 */
+ "CSI1_DP1", /* GPIO_72, HSEC pin 48 */
+ "CSI1_CN", /* GPIO_73, HSEC pin 56 */
+ "CSI1_CP", /* GPIO_74, HSEC pin 54 */
+ "[CLK1]"; /* GPIO_75, HSEC pin 17 */
+};
+
+&gpiod {
+ gpio-line-names =
+ "[GPIOD0]", /* GPIO_76 */
+ "[GPIOD1]", /* GPIO_77 */
+ "BT_RST_N", /* GPIO_78 */
+ "EXT_DC_EN", /* GPIO_79 */
+ "[PCM_DI]", /* GPIO_80, LSEC pin 22 */
+ "[PCM_DO]", /* GPIO_81, LSEC pin 20 */
+ "[PCM_CLK]", /* GPIO_82, LSEC pin 18 */
+ "[PCM_FS]", /* GPIO_83, LSEC pin 16 */
+ "WAKE_BT", /* GPIO_84 */
+ "WL_REG_ON", /* GPIO_85 */
+ "NC", /* GPIO_86 */
+ "NC", /* GPIO_87 */
+ "NC", /* GPIO_88 */
+ "NC", /* GPIO_89 */
+ "NC", /* GPIO_90 */
+ "WIFI_WAKE", /* GPIO_91 */
+ "BT_WAKE", /* GPIO_92 */
+ "NC", /* GPIO_93 */
+ "OTG_EN2", /* GPIO_94 */
+ "OTG_EN", /* GPIO_95 */
+ "DSI_DP3", /* GPIO_96, HSEC pin 45 */
+ "DSI_DN3", /* GPIO_97, HSEC pin 47 */
+ "DSI_DP1", /* GPIO_98, HSEC pin 33 */
+ "DSI_DN1", /* GPIO_99, HSEC pin 35 */
+ "DSI_CP", /* GPIO_100, HSEC pin 21 */
+ "DSI_CN", /* GPIO_101, HSEC pin 23 */
+ "DSI_DP0", /* GPIO_102, HSEC pin 27 */
+ "DSI_DN0", /* GPIO_103, HSEC pin 29 */
+ "DSI_DP2", /* GPIO_104, HSEC pin 39 */
+ "DSI_DN2"; /* GPIO_105, HSEC pin 41 */
+};
+
+&gpioe {
+ gpio-line-names =
+ "N0_D0", /* GPIO_106 */
+ "N0_D1", /* GPIO_107 */
+ "N0_D2", /* GPIO_108 */
+ "N0_D3", /* GPIO_109 */
+ "N0_D4", /* GPIO_110 */
+ "N0_D5", /* GPIO_111 */
+ "N0_D6", /* GPIO_112 */
+ "N0_D7", /* GPIO_113 */
+ "N0_DQS", /* GPIO_114 */
+ "N0_DQSN", /* GPIO_115 */
+ "NC", /* GPIO_116 */
+ "NC", /* GPIO_117 */
+ "NC", /* GPIO_118 */
+ "N0_CEB1", /* GPIO_119 */
+ "CARD_DT", /* GPIO_120 */
+ "N0_CEB3", /* GPIO_121 */
+ "SD_DAT0", /* GPIO_122, HSEC pin 1 */
+ "SD_DAT1", /* GPIO_123, HSEC pin 3 */
+ "SD_DAT2", /* GPIO_124, HSEC pin 5 */
+ "SD_DAT3", /* GPIO_125, HSEC pin 7 */
+ "NC", /* GPIO_126 */
+ "NC", /* GPIO_127 */
+ "[PWR_BTN_N]", /* GPIO_128, LSEC pin 4 */
+ "[RST_BTN_N]", /* GPIO_129, LSEC pin 6 */
+ "NC", /* GPIO_130 */
+ "SD_CMD", /* GPIO_131 */
+ "GPIO-L", /* GPIO_132, LSEC pin 34 */
+ "GPIO-K", /* GPIO_133, LSEC pin 33 */
+ "NC", /* GPIO_134 */
+ "SD_SCLK", /* GPIO_135 */
+ "NC", /* GPIO_136 */
+ "JTAG_TRST"; /* GPIO_137 */
+};
+
+&gpiof {
+ gpio-line-names =
+ "I2C3_SCLK", /* GPIO_138 */
+ "LED2", /* GPIO_139 */
+ "LED3", /* GPIO_140 */
+ "I2C3_SDATA", /* GPIO_141 */
+ "UART3_RX", /* GPIO_142 */
+ "UART3_TX", /* GPIO_143 */
+ "UART3_RTSB", /* GPIO_144 */
+ "UART3_CTSB"; /* GPIO_145 */
+};
--
2.14.1
next prev parent reply other threads:[~2018-02-21 16:00 UTC|newest]
Thread overview: 42+ messages / expand[flat|nested] mbox.gz Atom feed top
2018-02-21 16:00 [PATCH v2 00/10] Add Actions Semi S900 pinctrl and gpio support Manivannan Sadhasivam
2018-02-21 16:00 ` Manivannan Sadhasivam
2018-02-21 16:00 ` Manivannan Sadhasivam
2018-02-21 16:00 ` [PATCH v2 01/10] dt-bindings: pinctrl: Add bindings for Actions S900 SoC Manivannan Sadhasivam
2018-02-21 16:00 ` Manivannan Sadhasivam
2018-02-21 16:00 ` Manivannan Sadhasivam
2018-02-21 16:00 ` [PATCH v2 02/10] arm64: dts: actions: Add pinctrl node for S900 Manivannan Sadhasivam
2018-02-21 16:00 ` Manivannan Sadhasivam
2018-02-21 16:00 ` Manivannan Sadhasivam
2018-02-21 16:00 ` [PATCH v2 03/10] arm64: actions: Enable PINCTRL in platforms Kconfig Manivannan Sadhasivam
2018-02-21 16:00 ` Manivannan Sadhasivam
2018-02-21 16:00 ` Manivannan Sadhasivam
2018-02-21 16:00 ` [PATCH v2 04/10] pinctrl: actions: Add Actions S900 pinctrl driver Manivannan Sadhasivam
2018-02-21 16:00 ` Manivannan Sadhasivam
2018-02-21 16:00 ` Manivannan Sadhasivam
2018-02-23 15:07 ` Linus Walleij
2018-02-23 15:07 ` Linus Walleij
2018-02-23 15:07 ` Linus Walleij
2018-02-21 16:00 ` [PATCH v2 05/10] dt-bindings: gpio: Add gpio nodes for Actions S900 SoC Manivannan Sadhasivam
2018-02-21 16:00 ` Manivannan Sadhasivam
2018-02-21 16:00 ` Manivannan Sadhasivam
2018-02-21 16:00 ` [PATCH v2 06/10] arm64: dts: actions: Add S900 gpio nodes Manivannan Sadhasivam
2018-02-21 16:00 ` Manivannan Sadhasivam
2018-02-21 16:00 ` Manivannan Sadhasivam
2018-02-21 16:00 ` Manivannan Sadhasivam [this message]
2018-02-21 16:00 ` [PATCH v2 07/10] arm64: dts: actions: Add gpio line names to Bubblegum-96 board Manivannan Sadhasivam
2018-02-21 16:00 ` Manivannan Sadhasivam
2018-02-21 16:00 ` [PATCH v2 08/10] gpio: Add gpio driver for Actions OWL S900 SoC Manivannan Sadhasivam
2018-02-21 16:00 ` Manivannan Sadhasivam
2018-02-21 16:00 ` Manivannan Sadhasivam
2018-02-21 19:13 ` Andy Shevchenko
2018-02-21 19:13 ` Andy Shevchenko
2018-02-21 19:13 ` Andy Shevchenko
2018-02-21 22:38 ` Andreas Färber
2018-02-21 22:38 ` Andreas Färber
2018-02-21 22:38 ` Andreas Färber
2018-02-21 16:00 ` [PATCH v2 09/10] MAINTAINERS: Add reviewer for ACTIONS platforms Manivannan Sadhasivam
2018-02-21 16:00 ` Manivannan Sadhasivam
2018-02-21 16:00 ` Manivannan Sadhasivam
2018-02-21 16:00 ` [PATCH v2 10/10] MAINTAINERS: Add Actions Semi S900 pinctrl and gpio entries Manivannan Sadhasivam
2018-02-21 16:00 ` Manivannan Sadhasivam
2018-02-21 16:00 ` Manivannan Sadhasivam
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20180221160044.15089-8-manivannan.sadhasivam@linaro.org \
--to=manivannan.sadhasivam@linaro.org \
--cc=96boards@ucrobotics.com \
--cc=afaerber@suse.de \
--cc=amit.kucheria@linaro.org \
--cc=bdong@ucrobotics.com \
--cc=daniel.thompson@linaro.org \
--cc=devicetree@vger.kernel.org \
--cc=hzhang@ucrobotics.com \
--cc=linus.walleij@linaro.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-gpio@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=liuwei@actions-semi.com \
--cc=mp-cs@actions-semi.com \
--cc=robh+dt@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.