From: Douglas Anderson <dianders@chromium.org>
To: Andy Gross <andy.gross@linaro.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>,
swboyd@chromium.org, tfiga@chromium.org,
Manu Gautam <mgautam@codeaurora.org>,
David Collins <collinsd@codeaurora.org>,
Vivek Gautam <vivek.gautam@codeaurora.org>,
Douglas Anderson <dianders@chromium.org>,
devicetree@vger.kernel.org, linux-arm-msm@vger.kernel.org,
linux-kernel@vger.kernel.org, Rob Herring <robh+dt@kernel.org>,
David Brown <david.brown@linaro.org>,
Will Deacon <will.deacon@arm.com>,
Mark Rutland <mark.rutland@arm.com>,
linux-soc@vger.kernel.org,
Catalin Marinas <catalin.marinas@arm.com>,
linux-arm-kernel@lists.infradead.org
Subject: [PATCH 1/3] arm64: dts: qcom: sdm845: Add USB-related nodes
Date: Fri, 10 Aug 2018 14:51:48 -0700 [thread overview]
Message-ID: <20180810215150.82490-2-dianders@chromium.org> (raw)
In-Reply-To: <20180810215150.82490-1-dianders@chromium.org>
From: Manu Gautam <mgautam@codeaurora.org>
This adds nodes for USB and related PHYs.
Signed-off-by: Manu Gautam <mgautam@codeaurora.org>
[dianders: reworked quite a bit]
Signed-off-by: Douglas Anderson <dianders@chromium.org>
---
Changes in v2:
- Use "0x784000" for qfprom rather than "0x780000" as per docs.
- Add calibration for 2nd USB port too
arch/arm64/boot/dts/qcom/sdm845.dtsi | 196 +++++++++++++++++++++++++++
1 file changed, 196 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/sdm845.dtsi b/arch/arm64/boot/dts/qcom/sdm845.dtsi
index ae57c065780c..f13d8c2fb4a5 100644
--- a/arch/arm64/boot/dts/qcom/sdm845.dtsi
+++ b/arch/arm64/boot/dts/qcom/sdm845.dtsi
@@ -8,6 +8,7 @@
#include <dt-bindings/clock/qcom,gcc-sdm845.h>
#include <dt-bindings/clock/qcom,rpmh.h>
#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/phy/phy-qcom-qusb2.h>
#include <dt-bindings/soc/qcom,rpmh-rsc.h>
/ {
@@ -249,6 +250,23 @@
#power-domain-cells = <1>;
};
+ qfprom@784000 {
+ compatible = "qcom,qfprom";
+ reg = <0x780000 0x8ff>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ qusb2p_hstx_trim: hstx-trim-primary@1eb {
+ reg = <0x1eb 0x1>;
+ bits = <1 4>;
+ };
+
+ qusb2s_hstx_trim: hstx-trim-secondary@1eb {
+ reg = <0x1eb 0x2>;
+ bits = <6 4>;
+ };
+ };
+
qupv3_id_0: geniqup@8c0000 {
compatible = "qcom,geni-se-qup";
reg = <0x8c0000 0x6000>;
@@ -962,6 +980,184 @@
};
};
+ usb_1_hsphy: phy@88e2000 {
+ compatible = "qcom,sdm845-qusb2-phy";
+ reg = <0x88e2000 0x400>;
+ status = "disabled";
+ #phy-cells = <0>;
+
+ clocks = <&gcc GCC_USB_PHY_CFG_AHB2PHY_CLK>,
+ <&rpmhcc RPMH_CXO_CLK>;
+ clock-names = "cfg_ahb", "ref";
+
+ resets = <&gcc GCC_QUSB2PHY_PRIM_BCR>;
+
+ nvmem-cells = <&qusb2p_hstx_trim>;
+ };
+
+ usb_2_hsphy: phy@88e3000 {
+ compatible = "qcom,sdm845-qusb2-phy";
+ reg = <0x88e3000 0x400>;
+ status = "disabled";
+ #phy-cells = <0>;
+
+ clocks = <&gcc GCC_USB_PHY_CFG_AHB2PHY_CLK>,
+ <&rpmhcc RPMH_CXO_CLK>;
+ clock-names = "cfg_ahb", "ref";
+
+ resets = <&gcc GCC_QUSB2PHY_SEC_BCR>;
+
+ nvmem-cells = <&qusb2s_hstx_trim>;
+ };
+
+ usb_1_qmpphy: phy@88e9000 {
+ compatible = "qcom,sdm845-qmp-usb3-phy";
+ reg = <0x88e9000 0x18c>,
+ <0x88e8000 0x10>;
+ reg-names = "reg-base", "dp_com";
+ status = "disabled";
+ #clock-cells = <1>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ clocks = <&gcc GCC_USB3_PRIM_PHY_AUX_CLK>,
+ <&gcc GCC_USB_PHY_CFG_AHB2PHY_CLK>,
+ <&gcc GCC_USB3_PRIM_CLKREF_CLK>,
+ <&gcc GCC_USB3_PRIM_PHY_COM_AUX_CLK>;
+ clock-names = "aux", "cfg_ahb", "ref", "com_aux";
+
+ resets = <&gcc GCC_USB3_DP_PHY_PRIM_BCR>,
+ <&gcc GCC_USB3_PHY_PRIM_BCR>;
+ reset-names = "phy", "common";
+
+ usb_1_ssphy: lane@88e9200 {
+ reg = <0x88e9200 0x128>,
+ <0x88e9400 0x200>,
+ <0x88e9c00 0x218>,
+ <0x88e9a00 0x100>;
+ #phy-cells = <0>;
+ clocks = <&gcc GCC_USB3_PRIM_PHY_PIPE_CLK>;
+ clock-names = "pipe0";
+ clock-output-names = "usb3_phy_pipe_clk_src";
+ };
+ };
+
+ usb_2_qmpphy: phy@88eb000 {
+ compatible = "qcom,sdm845-qmp-usb3-uni-phy";
+ reg = <0x88eb000 0x18c>;
+ status = "disabled";
+ #clock-cells = <1>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ clocks = <&gcc GCC_USB3_SEC_PHY_AUX_CLK>,
+ <&gcc GCC_USB_PHY_CFG_AHB2PHY_CLK>,
+ <&gcc GCC_USB3_SEC_CLKREF_CLK>,
+ <&gcc GCC_USB3_SEC_PHY_COM_AUX_CLK>;
+ clock-names = "aux", "cfg_ahb", "ref", "com_aux";
+
+ resets = <&gcc GCC_USB3PHY_PHY_SEC_BCR>,
+ <&gcc GCC_USB3_PHY_SEC_BCR>;
+ reset-names = "phy", "common";
+
+ usb_2_ssphy: lane@88eb200 {
+ reg = <0x88eb200 0x128>,
+ <0x88eb400 0x1fc>,
+ <0x88eb800 0x218>,
+ <0x88e9600 0x70>;
+ #phy-cells = <0>;
+ clocks = <&gcc GCC_USB3_SEC_PHY_PIPE_CLK>;
+ clock-names = "pipe0";
+ clock-output-names = "usb3_uni_phy_pipe_clk_src";
+ };
+ };
+
+ usb_1: usb@a6f8800 {
+ compatible = "qcom,sdm845-dwc3", "qcom,dwc3";
+ reg = <0xa6f8800 0x400>;
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ clocks = <&gcc GCC_CFG_NOC_USB3_PRIM_AXI_CLK>,
+ <&gcc GCC_USB30_PRIM_MASTER_CLK>,
+ <&gcc GCC_AGGRE_USB3_PRIM_AXI_CLK>,
+ <&gcc GCC_USB30_PRIM_MOCK_UTMI_CLK>,
+ <&gcc GCC_USB30_PRIM_SLEEP_CLK>;
+ clock-names = "cfg_noc", "core", "iface", "mock_utmi",
+ "sleep";
+
+ assigned-clocks = <&gcc GCC_USB30_PRIM_MOCK_UTMI_CLK>,
+ <&gcc GCC_USB30_PRIM_MASTER_CLK>;
+ assigned-clock-rates = <19200000>, <150000000>;
+
+ interrupts = <GIC_SPI 131 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 486 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 488 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 489 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "hs_phy_irq", "ss_phy_irq",
+ "dm_hs_phy_irq", "dp_hs_phy_irq";
+
+ power-domains = <&gcc USB30_PRIM_GDSC>;
+
+ resets = <&gcc GCC_USB30_PRIM_BCR>;
+
+ usb_1_dwc3: dwc3@a600000 {
+ compatible = "snps,dwc3";
+ reg = <0xa600000 0xcd00>;
+ interrupts = <GIC_SPI 133 IRQ_TYPE_LEVEL_HIGH>;
+ snps,dis_u2_susphy_quirk;
+ snps,dis_enblslpm_quirk;
+ phys = <&usb_1_hsphy>, <&usb_1_ssphy>;
+ phy-names = "usb2-phy", "usb3-phy";
+ };
+ };
+
+ usb_2: usb@a8f8800 {
+ compatible = "qcom,sdm845-dwc3", "qcom,dwc3";
+ reg = <0xa8f8800 0x400>;
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ clocks = <&gcc GCC_CFG_NOC_USB3_SEC_AXI_CLK>,
+ <&gcc GCC_USB30_SEC_MASTER_CLK>,
+ <&gcc GCC_AGGRE_USB3_SEC_AXI_CLK>,
+ <&gcc GCC_USB30_SEC_MOCK_UTMI_CLK>,
+ <&gcc GCC_USB30_SEC_SLEEP_CLK>;
+ clock-names = "cfg_noc", "core", "iface", "mock_utmi",
+ "sleep";
+
+ assigned-clocks = <&gcc GCC_USB30_SEC_MOCK_UTMI_CLK>,
+ <&gcc GCC_USB30_SEC_MASTER_CLK>;
+ assigned-clock-rates = <19200000>, <150000000>;
+
+ interrupts = <GIC_SPI 136 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 487 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 490 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 491 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "hs_phy_irq", "ss_phy_irq",
+ "dm_hs_phy_irq", "dp_hs_phy_irq";
+
+ power-domains = <&gcc USB30_SEC_GDSC>;
+
+ resets = <&gcc GCC_USB30_SEC_BCR>;
+
+ usb_2_dwc3: dwc3@a800000 {
+ compatible = "snps,dwc3";
+ reg = <0xa800000 0xcd00>;
+ interrupts = <GIC_SPI 138 IRQ_TYPE_LEVEL_HIGH>;
+ snps,dis_u2_susphy_quirk;
+ snps,dis_enblslpm_quirk;
+ phys = <&usb_2_hsphy>, <&usb_2_ssphy>;
+ phy-names = "usb2-phy", "usb3-phy";
+ };
+ };
+
spmi_bus: spmi@c440000 {
compatible = "qcom,spmi-pmic-arb";
reg = <0xc440000 0x1100>,
--
2.18.0.597.ga71716f1ad-goog
WARNING: multiple messages have this Message-ID (diff)
From: dianders@chromium.org (Douglas Anderson)
To: linux-arm-kernel@lists.infradead.org
Subject: [PATCH 1/3] arm64: dts: qcom: sdm845: Add USB-related nodes
Date: Fri, 10 Aug 2018 14:51:48 -0700 [thread overview]
Message-ID: <20180810215150.82490-2-dianders@chromium.org> (raw)
In-Reply-To: <20180810215150.82490-1-dianders@chromium.org>
From: Manu Gautam <mgautam@codeaurora.org>
This adds nodes for USB and related PHYs.
Signed-off-by: Manu Gautam <mgautam@codeaurora.org>
[dianders: reworked quite a bit]
Signed-off-by: Douglas Anderson <dianders@chromium.org>
---
Changes in v2:
- Use "0x784000" for qfprom rather than "0x780000" as per docs.
- Add calibration for 2nd USB port too
arch/arm64/boot/dts/qcom/sdm845.dtsi | 196 +++++++++++++++++++++++++++
1 file changed, 196 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/sdm845.dtsi b/arch/arm64/boot/dts/qcom/sdm845.dtsi
index ae57c065780c..f13d8c2fb4a5 100644
--- a/arch/arm64/boot/dts/qcom/sdm845.dtsi
+++ b/arch/arm64/boot/dts/qcom/sdm845.dtsi
@@ -8,6 +8,7 @@
#include <dt-bindings/clock/qcom,gcc-sdm845.h>
#include <dt-bindings/clock/qcom,rpmh.h>
#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/phy/phy-qcom-qusb2.h>
#include <dt-bindings/soc/qcom,rpmh-rsc.h>
/ {
@@ -249,6 +250,23 @@
#power-domain-cells = <1>;
};
+ qfprom at 784000 {
+ compatible = "qcom,qfprom";
+ reg = <0x780000 0x8ff>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ qusb2p_hstx_trim: hstx-trim-primary at 1eb {
+ reg = <0x1eb 0x1>;
+ bits = <1 4>;
+ };
+
+ qusb2s_hstx_trim: hstx-trim-secondary at 1eb {
+ reg = <0x1eb 0x2>;
+ bits = <6 4>;
+ };
+ };
+
qupv3_id_0: geniqup at 8c0000 {
compatible = "qcom,geni-se-qup";
reg = <0x8c0000 0x6000>;
@@ -962,6 +980,184 @@
};
};
+ usb_1_hsphy: phy at 88e2000 {
+ compatible = "qcom,sdm845-qusb2-phy";
+ reg = <0x88e2000 0x400>;
+ status = "disabled";
+ #phy-cells = <0>;
+
+ clocks = <&gcc GCC_USB_PHY_CFG_AHB2PHY_CLK>,
+ <&rpmhcc RPMH_CXO_CLK>;
+ clock-names = "cfg_ahb", "ref";
+
+ resets = <&gcc GCC_QUSB2PHY_PRIM_BCR>;
+
+ nvmem-cells = <&qusb2p_hstx_trim>;
+ };
+
+ usb_2_hsphy: phy at 88e3000 {
+ compatible = "qcom,sdm845-qusb2-phy";
+ reg = <0x88e3000 0x400>;
+ status = "disabled";
+ #phy-cells = <0>;
+
+ clocks = <&gcc GCC_USB_PHY_CFG_AHB2PHY_CLK>,
+ <&rpmhcc RPMH_CXO_CLK>;
+ clock-names = "cfg_ahb", "ref";
+
+ resets = <&gcc GCC_QUSB2PHY_SEC_BCR>;
+
+ nvmem-cells = <&qusb2s_hstx_trim>;
+ };
+
+ usb_1_qmpphy: phy at 88e9000 {
+ compatible = "qcom,sdm845-qmp-usb3-phy";
+ reg = <0x88e9000 0x18c>,
+ <0x88e8000 0x10>;
+ reg-names = "reg-base", "dp_com";
+ status = "disabled";
+ #clock-cells = <1>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ clocks = <&gcc GCC_USB3_PRIM_PHY_AUX_CLK>,
+ <&gcc GCC_USB_PHY_CFG_AHB2PHY_CLK>,
+ <&gcc GCC_USB3_PRIM_CLKREF_CLK>,
+ <&gcc GCC_USB3_PRIM_PHY_COM_AUX_CLK>;
+ clock-names = "aux", "cfg_ahb", "ref", "com_aux";
+
+ resets = <&gcc GCC_USB3_DP_PHY_PRIM_BCR>,
+ <&gcc GCC_USB3_PHY_PRIM_BCR>;
+ reset-names = "phy", "common";
+
+ usb_1_ssphy: lane at 88e9200 {
+ reg = <0x88e9200 0x128>,
+ <0x88e9400 0x200>,
+ <0x88e9c00 0x218>,
+ <0x88e9a00 0x100>;
+ #phy-cells = <0>;
+ clocks = <&gcc GCC_USB3_PRIM_PHY_PIPE_CLK>;
+ clock-names = "pipe0";
+ clock-output-names = "usb3_phy_pipe_clk_src";
+ };
+ };
+
+ usb_2_qmpphy: phy at 88eb000 {
+ compatible = "qcom,sdm845-qmp-usb3-uni-phy";
+ reg = <0x88eb000 0x18c>;
+ status = "disabled";
+ #clock-cells = <1>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ clocks = <&gcc GCC_USB3_SEC_PHY_AUX_CLK>,
+ <&gcc GCC_USB_PHY_CFG_AHB2PHY_CLK>,
+ <&gcc GCC_USB3_SEC_CLKREF_CLK>,
+ <&gcc GCC_USB3_SEC_PHY_COM_AUX_CLK>;
+ clock-names = "aux", "cfg_ahb", "ref", "com_aux";
+
+ resets = <&gcc GCC_USB3PHY_PHY_SEC_BCR>,
+ <&gcc GCC_USB3_PHY_SEC_BCR>;
+ reset-names = "phy", "common";
+
+ usb_2_ssphy: lane at 88eb200 {
+ reg = <0x88eb200 0x128>,
+ <0x88eb400 0x1fc>,
+ <0x88eb800 0x218>,
+ <0x88e9600 0x70>;
+ #phy-cells = <0>;
+ clocks = <&gcc GCC_USB3_SEC_PHY_PIPE_CLK>;
+ clock-names = "pipe0";
+ clock-output-names = "usb3_uni_phy_pipe_clk_src";
+ };
+ };
+
+ usb_1: usb at a6f8800 {
+ compatible = "qcom,sdm845-dwc3", "qcom,dwc3";
+ reg = <0xa6f8800 0x400>;
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ clocks = <&gcc GCC_CFG_NOC_USB3_PRIM_AXI_CLK>,
+ <&gcc GCC_USB30_PRIM_MASTER_CLK>,
+ <&gcc GCC_AGGRE_USB3_PRIM_AXI_CLK>,
+ <&gcc GCC_USB30_PRIM_MOCK_UTMI_CLK>,
+ <&gcc GCC_USB30_PRIM_SLEEP_CLK>;
+ clock-names = "cfg_noc", "core", "iface", "mock_utmi",
+ "sleep";
+
+ assigned-clocks = <&gcc GCC_USB30_PRIM_MOCK_UTMI_CLK>,
+ <&gcc GCC_USB30_PRIM_MASTER_CLK>;
+ assigned-clock-rates = <19200000>, <150000000>;
+
+ interrupts = <GIC_SPI 131 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 486 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 488 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 489 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "hs_phy_irq", "ss_phy_irq",
+ "dm_hs_phy_irq", "dp_hs_phy_irq";
+
+ power-domains = <&gcc USB30_PRIM_GDSC>;
+
+ resets = <&gcc GCC_USB30_PRIM_BCR>;
+
+ usb_1_dwc3: dwc3 at a600000 {
+ compatible = "snps,dwc3";
+ reg = <0xa600000 0xcd00>;
+ interrupts = <GIC_SPI 133 IRQ_TYPE_LEVEL_HIGH>;
+ snps,dis_u2_susphy_quirk;
+ snps,dis_enblslpm_quirk;
+ phys = <&usb_1_hsphy>, <&usb_1_ssphy>;
+ phy-names = "usb2-phy", "usb3-phy";
+ };
+ };
+
+ usb_2: usb at a8f8800 {
+ compatible = "qcom,sdm845-dwc3", "qcom,dwc3";
+ reg = <0xa8f8800 0x400>;
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ clocks = <&gcc GCC_CFG_NOC_USB3_SEC_AXI_CLK>,
+ <&gcc GCC_USB30_SEC_MASTER_CLK>,
+ <&gcc GCC_AGGRE_USB3_SEC_AXI_CLK>,
+ <&gcc GCC_USB30_SEC_MOCK_UTMI_CLK>,
+ <&gcc GCC_USB30_SEC_SLEEP_CLK>;
+ clock-names = "cfg_noc", "core", "iface", "mock_utmi",
+ "sleep";
+
+ assigned-clocks = <&gcc GCC_USB30_SEC_MOCK_UTMI_CLK>,
+ <&gcc GCC_USB30_SEC_MASTER_CLK>;
+ assigned-clock-rates = <19200000>, <150000000>;
+
+ interrupts = <GIC_SPI 136 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 487 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 490 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 491 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "hs_phy_irq", "ss_phy_irq",
+ "dm_hs_phy_irq", "dp_hs_phy_irq";
+
+ power-domains = <&gcc USB30_SEC_GDSC>;
+
+ resets = <&gcc GCC_USB30_SEC_BCR>;
+
+ usb_2_dwc3: dwc3 at a800000 {
+ compatible = "snps,dwc3";
+ reg = <0xa800000 0xcd00>;
+ interrupts = <GIC_SPI 138 IRQ_TYPE_LEVEL_HIGH>;
+ snps,dis_u2_susphy_quirk;
+ snps,dis_enblslpm_quirk;
+ phys = <&usb_2_hsphy>, <&usb_2_ssphy>;
+ phy-names = "usb2-phy", "usb3-phy";
+ };
+ };
+
spmi_bus: spmi at c440000 {
compatible = "qcom,spmi-pmic-arb";
reg = <0xc440000 0x1100>,
--
2.18.0.597.ga71716f1ad-goog
next prev parent reply other threads:[~2018-08-10 21:51 UTC|newest]
Thread overview: 26+ messages / expand[flat|nested] mbox.gz Atom feed top
2018-08-10 21:51 [PATCH 0/3] arm64: dts: sdm845: Add RPMh-regulators and usb Douglas Anderson
2018-08-10 21:51 ` Douglas Anderson
2018-08-10 21:51 ` Douglas Anderson
2018-08-10 21:51 ` Douglas Anderson [this message]
2018-08-10 21:51 ` [PATCH 1/3] arm64: dts: qcom: sdm845: Add USB-related nodes Douglas Anderson
2018-08-20 18:17 ` Stephen Boyd
2018-08-20 18:17 ` Stephen Boyd
2018-08-20 18:17 ` Stephen Boyd
2018-08-22 17:37 ` Doug Anderson
2018-08-22 17:37 ` Doug Anderson
2018-08-10 21:51 ` [PATCH 2/3] arm64: dts: qcom: sdm845-mtp: Add RPMh VRM/XOB regulators Douglas Anderson
2018-08-10 21:51 ` Douglas Anderson
2018-08-12 7:06 ` kbuild test robot
2018-08-12 7:06 ` kbuild test robot
2018-08-12 7:06 ` kbuild test robot
2018-08-20 18:18 ` Stephen Boyd
2018-08-20 18:18 ` Stephen Boyd
2018-08-20 18:18 ` Stephen Boyd
2018-08-22 17:38 ` Doug Anderson
2018-08-22 17:38 ` Doug Anderson
2018-08-10 21:51 ` [PATCH 3/3] arm64: dts: qcom: sdm845-mtp: Add nodes for USB Douglas Anderson
2018-08-10 21:51 ` Douglas Anderson
-- strict thread matches above, loose matches on Subject: below --
2018-07-10 22:01 [PATCH 0/3] arm64: dts: sdm845: Add RPMh-regulators and usb Douglas Anderson
2018-07-10 22:02 ` [PATCH 1/3] arm64: dts: qcom: sdm845: Add USB-related nodes Douglas Anderson
2018-07-10 22:02 ` Douglas Anderson
2018-07-12 16:56 ` Doug Anderson
2018-07-12 16:56 ` Doug Anderson
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20180810215150.82490-2-dianders@chromium.org \
--to=dianders@chromium.org \
--cc=andy.gross@linaro.org \
--cc=bjorn.andersson@linaro.org \
--cc=catalin.marinas@arm.com \
--cc=collinsd@codeaurora.org \
--cc=david.brown@linaro.org \
--cc=devicetree@vger.kernel.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-arm-msm@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-soc@vger.kernel.org \
--cc=mark.rutland@arm.com \
--cc=mgautam@codeaurora.org \
--cc=robh+dt@kernel.org \
--cc=swboyd@chromium.org \
--cc=tfiga@chromium.org \
--cc=vivek.gautam@codeaurora.org \
--cc=will.deacon@arm.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.