From: Peter Rosin <peda@axentia.se> To: linux-kernel@vger.kernel.org Cc: Peter Rosin <peda@axentia.se>, Boris Brezillon <boris.brezillon@bootlin.com>, David Airlie <airlied@linux.ie>, Nicolas Ferre <nicolas.ferre@microchip.com>, Alexandre Belloni <alexandre.belloni@bootlin.com>, dri-devel@lists.freedesktop.org, linux-arm-kernel@lists.infradead.org Subject: [PATCH 2/2] drm/atmel-hlcdc: allow selecting a higher pixel-clock that requested Date: Fri, 24 Aug 2018 10:55:01 +0200 [thread overview] Message-ID: <20180824085501.9740-3-peda@axentia.se> (raw) In-Reply-To: <20180824085501.9740-1-peda@axentia.se> But only if the highest pixel-clock frequency lower than requested is significantly much less accurate that the lowest frequency higher than requested. I pulled "10 times" as the discriminator out of the hat, and went with that. This is useful, if e.g. the target pixel-clock is 65MHz and the sys_clk is 132MHz. In this case the highest possible pixel-clock lower than the requested 65MHz is 52.8MHz, which is almost 20% off (and outside the spec for the panel). The lowest possible pixel-clock higher than 65MHz is 66MHz, which is a *much* better match, and only 1.5% off. Signed-off-by: Peter Rosin <peda@axentia.se> --- drivers/gpu/drm/atmel-hlcdc/atmel_hlcdc_crtc.c | 13 +++++++++++++ 1 file changed, 13 insertions(+) diff --git a/drivers/gpu/drm/atmel-hlcdc/atmel_hlcdc_crtc.c b/drivers/gpu/drm/atmel-hlcdc/atmel_hlcdc_crtc.c index 71c9cd90d2ae..0c2717ed4ac6 100644 --- a/drivers/gpu/drm/atmel-hlcdc/atmel_hlcdc_crtc.c +++ b/drivers/gpu/drm/atmel-hlcdc/atmel_hlcdc_crtc.c @@ -116,6 +116,19 @@ static void atmel_hlcdc_crtc_mode_set_nofb(struct drm_crtc *c) div = DIV_ROUND_UP(prate, mode_rate); if (ATMEL_HLCDC_CLKDIV(div) & ~ATMEL_HLCDC_CLKDIV_MASK) div = ATMEL_HLCDC_CLKDIV_MASK; + } else { + int div_low = prate / mode_rate; + + if (div_low >= 2 && + ((prate / div_low - mode_rate) < + 10 * (mode_rate - prate / div))) + /* + * At least 10 times better when + * using a higher frequency than + * requested, instead of a lower. + * So, go with that. + */ + div = div_low; } cfg |= ATMEL_HLCDC_CLKDIV(div); -- 2.11.0
WARNING: multiple messages have this Message-ID (diff)
From: peda@axentia.se (Peter Rosin) To: linux-arm-kernel@lists.infradead.org Subject: [PATCH 2/2] drm/atmel-hlcdc: allow selecting a higher pixel-clock that requested Date: Fri, 24 Aug 2018 10:55:01 +0200 [thread overview] Message-ID: <20180824085501.9740-3-peda@axentia.se> (raw) In-Reply-To: <20180824085501.9740-1-peda@axentia.se> But only if the highest pixel-clock frequency lower than requested is significantly much less accurate that the lowest frequency higher than requested. I pulled "10 times" as the discriminator out of the hat, and went with that. This is useful, if e.g. the target pixel-clock is 65MHz and the sys_clk is 132MHz. In this case the highest possible pixel-clock lower than the requested 65MHz is 52.8MHz, which is almost 20% off (and outside the spec for the panel). The lowest possible pixel-clock higher than 65MHz is 66MHz, which is a *much* better match, and only 1.5% off. Signed-off-by: Peter Rosin <peda@axentia.se> --- drivers/gpu/drm/atmel-hlcdc/atmel_hlcdc_crtc.c | 13 +++++++++++++ 1 file changed, 13 insertions(+) diff --git a/drivers/gpu/drm/atmel-hlcdc/atmel_hlcdc_crtc.c b/drivers/gpu/drm/atmel-hlcdc/atmel_hlcdc_crtc.c index 71c9cd90d2ae..0c2717ed4ac6 100644 --- a/drivers/gpu/drm/atmel-hlcdc/atmel_hlcdc_crtc.c +++ b/drivers/gpu/drm/atmel-hlcdc/atmel_hlcdc_crtc.c @@ -116,6 +116,19 @@ static void atmel_hlcdc_crtc_mode_set_nofb(struct drm_crtc *c) div = DIV_ROUND_UP(prate, mode_rate); if (ATMEL_HLCDC_CLKDIV(div) & ~ATMEL_HLCDC_CLKDIV_MASK) div = ATMEL_HLCDC_CLKDIV_MASK; + } else { + int div_low = prate / mode_rate; + + if (div_low >= 2 && + ((prate / div_low - mode_rate) < + 10 * (mode_rate - prate / div))) + /* + * At least 10 times better when + * using a higher frequency than + * requested, instead of a lower. + * So, go with that. + */ + div = div_low; } cfg |= ATMEL_HLCDC_CLKDIV(div); -- 2.11.0
next prev parent reply other threads:[~2018-08-24 8:55 UTC|newest] Thread overview: 12+ messages / expand[flat|nested] mbox.gz Atom feed top 2018-08-24 8:54 [PATCH 0/2] drm/atmel-hlcdc: revise selection of pixel-clock frequency divider Peter Rosin 2018-08-24 8:54 ` Peter Rosin 2018-08-24 8:55 ` [PATCH 1/2] drm/atmel-hlcdc: prefer a higher rate clock as pixel-clock base Peter Rosin 2018-08-24 8:55 ` Peter Rosin 2018-08-24 8:59 ` Boris Brezillon 2018-08-24 8:59 ` Boris Brezillon 2018-08-24 8:59 ` Boris Brezillon 2018-08-24 8:55 ` Peter Rosin [this message] 2018-08-24 8:55 ` [PATCH 2/2] drm/atmel-hlcdc: allow selecting a higher pixel-clock that requested Peter Rosin 2018-08-24 9:07 ` Boris Brezillon 2018-08-24 9:07 ` Boris Brezillon 2018-08-24 9:07 ` Boris Brezillon
Reply instructions: You may reply publicly to this message via plain-text email using any one of the following methods: * Save the following mbox file, import it into your mail client, and reply-to-all from there: mbox Avoid top-posting and favor interleaved quoting: https://en.wikipedia.org/wiki/Posting_style#Interleaved_style * Reply using the --to, --cc, and --in-reply-to switches of git-send-email(1): git send-email \ --in-reply-to=20180824085501.9740-3-peda@axentia.se \ --to=peda@axentia.se \ --cc=airlied@linux.ie \ --cc=alexandre.belloni@bootlin.com \ --cc=boris.brezillon@bootlin.com \ --cc=dri-devel@lists.freedesktop.org \ --cc=linux-arm-kernel@lists.infradead.org \ --cc=linux-kernel@vger.kernel.org \ --cc=nicolas.ferre@microchip.com \ /path/to/YOUR_REPLY https://kernel.org/pub/software/scm/git/docs/git-send-email.html * If your mail client supports setting the In-Reply-To header via mailto: links, try the mailto: linkBe sure your reply has a Subject: header at the top and a blank line before the message body.
This is an external index of several public inboxes, see mirroring instructions on how to clone and mirror all data and code used by this external index.