[PATCH] ARM: dts: at91: sama5d2 Xplained: add QSPI0 + SPI NOR memory nodes

[<Tudor.Ambarus@microchip.com>]

From: Cyrille Pitchen <cyrille.pitchen@microchip.com>

This patch configures the QSPI0 controller pin muxing and declares
a jedec,spi-nor memory.

sama5d2 Xplained RevB and RevC use the Macronix MX25L25673G flash
memory which advertises a maximum frequency of 80MHz for Quad IO
Fast Read. Set the spi-max-frequency to 80MHz knowing that actually
the QSPI drver will set the SPI bus clock to 166MHz / 3 = 55.3MHz.

Signed-off-by: Cyrille Pitchen <cyrille.pitchen@microchip.com>
[tudor.ambarus@microchip.com:
- drop partitions,
- add spi-rx/tx-bus-width
- change spi-max-frequency to match the 80MHz limit advertised by
  MX25L25673G for Quad IO Fast Read,
- reword commit message and subject.]
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
---
 arch/arm/boot/dts/at91-sama5d2_xplained.dts | 31 +++++++++++++++++++++++++++++
 1 file changed, 31 insertions(+)

diff --git a/arch/arm/boot/dts/at91-sama5d2_xplained.dts b/arch/arm/boot/dts/at91-sama5d2_xplained.dts
index 518e2b095ccf..171bc82cfbbf 100644
--- a/arch/arm/boot/dts/at91-sama5d2_xplained.dts
+++ b/arch/arm/boot/dts/at91-sama5d2_xplained.dts
@@ -108,6 +108,21 @@
 		};
 
 		apb {
+			qspi0: spi@f0020000 {
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_qspi0_default>;
+				/* status = "okay"; */ /* conflict with sdmmc1 */
+
+				flash@0 {
+					compatible = "jedec,spi-nor";
+					reg = <0>;
+					spi-max-frequency = <80000000>;
+					spi-tx-bus-width = <4>;
+					spi-rx-bus-width = <4>;
+					m25p,fast-read;
+				};
+			};
+
 			spi0: spi@f8000000 {
 				pinctrl-names = "default";
 				pinctrl-0 = <&pinctrl_spi0_default>;
@@ -485,6 +500,22 @@
 					bias-disable;
 				};
 
+				pinctrl_qspi0_default: qspi0_default {
+					sck_cs {
+						pinmux = <PIN_PA22__QSPI0_SCK>,
+							 <PIN_PA23__QSPI0_CS>;
+						bias-disable;
+					};
+
+					data {
+						pinmux = <PIN_PA24__QSPI0_IO0>,
+							 <PIN_PA25__QSPI0_IO1>,
+							 <PIN_PA26__QSPI0_IO2>,
+							 <PIN_PA27__QSPI0_IO3>;
+						bias-pull-up;
+					};
+				};
+
 				pinctrl_sdmmc0_default: sdmmc0_default {
 					cmd_data {
 						pinmux = <PIN_PA1__SDMMC0_CMD>,
-- 
2.9.4