From: Jerome Brunet <jbrunet@baylibre.com> To: Kevin Hilman <khilman@baylibre.com> Cc: Jerome Brunet <jbrunet@baylibre.com>, devicetree@vger.kernel.org, linux-amlogic@lists.infradead.org, linux-kernel@vger.kernel.org Subject: [PATCH 2/3] arm64: dts: meson: u200: add sd and emmc Date: Tue, 14 May 2019 11:16:10 +0200 [thread overview] Message-ID: <20190514091611.15278-3-jbrunet@baylibre.com> (raw) In-Reply-To: <20190514091611.15278-1-jbrunet@baylibre.com> Enable eMMC and SDCard on the g12a u200 board Signed-off-by: Jerome Brunet <jbrunet@baylibre.com> --- .../boot/dts/amlogic/meson-g12a-u200.dts | 42 +++++++++++++++++++ 1 file changed, 42 insertions(+) diff --git a/arch/arm64/boot/dts/amlogic/meson-g12a-u200.dts b/arch/arm64/boot/dts/amlogic/meson-g12a-u200.dts index 7cc3e2d6a4f1..972926121beb 100644 --- a/arch/arm64/boot/dts/amlogic/meson-g12a-u200.dts +++ b/arch/arm64/boot/dts/amlogic/meson-g12a-u200.dts @@ -31,6 +31,11 @@ }; }; + emmc_pwrseq: emmc-pwrseq { + compatible = "mmc-pwrseq-emmc"; + reset-gpios = <&gpio BOOT_12 GPIO_ACTIVE_LOW>; + }; + hdmi-connector { compatible = "hdmi-connector"; type = "a"; @@ -164,6 +169,43 @@ pinctrl-names = "default"; }; +/* SD card */ +&sd_emmc_b { + status = "okay"; + pinctrl-0 = <&sdcard_c_pins>; + pinctrl-1 = <&sdcard_clk_gate_c_pins>; + pinctrl-names = "default", "clk-gate"; + + bus-width = <4>; + cap-sd-highspeed; + max-frequency = <50000000>; + disable-wp; + + cd-gpios = <&gpio GPIOC_6 GPIO_ACTIVE_LOW>; + vmmc-supply = <&vddao_3v3>; + vqmmc-supply = <&vddao_3v3>; +}; + +/* eMMC */ +&sd_emmc_c { + status = "okay"; + pinctrl-0 = <&emmc_pins>, <&emmc_ds_pins>; + pinctrl-1 = <&emmc_clk_gate_pins>; + pinctrl-names = "default", "clk-gate"; + + bus-width = <8>; + cap-mmc-highspeed; + mmc-ddr-1_8v; + mmc-hs200-1_8v; + max-frequency = <200000000>; + non-removable; + disable-wp; + + mmc-pwrseq = <&emmc_pwrseq>; + vmmc-supply = <&vcc_3v3>; + vqmmc-supply = <&flash_1v8>; +}; + &uart_AO { status = "okay"; pinctrl-0 = <&uart_ao_a_pins>; -- 2.20.1
WARNING: multiple messages have this Message-ID (diff)
From: Jerome Brunet <jbrunet@baylibre.com> To: Kevin Hilman <khilman@baylibre.com> Cc: devicetree@vger.kernel.org, linux-amlogic@lists.infradead.org, linux-kernel@vger.kernel.org, Jerome Brunet <jbrunet@baylibre.com> Subject: [PATCH 2/3] arm64: dts: meson: u200: add sd and emmc Date: Tue, 14 May 2019 11:16:10 +0200 [thread overview] Message-ID: <20190514091611.15278-3-jbrunet@baylibre.com> (raw) In-Reply-To: <20190514091611.15278-1-jbrunet@baylibre.com> Enable eMMC and SDCard on the g12a u200 board Signed-off-by: Jerome Brunet <jbrunet@baylibre.com> --- .../boot/dts/amlogic/meson-g12a-u200.dts | 42 +++++++++++++++++++ 1 file changed, 42 insertions(+) diff --git a/arch/arm64/boot/dts/amlogic/meson-g12a-u200.dts b/arch/arm64/boot/dts/amlogic/meson-g12a-u200.dts index 7cc3e2d6a4f1..972926121beb 100644 --- a/arch/arm64/boot/dts/amlogic/meson-g12a-u200.dts +++ b/arch/arm64/boot/dts/amlogic/meson-g12a-u200.dts @@ -31,6 +31,11 @@ }; }; + emmc_pwrseq: emmc-pwrseq { + compatible = "mmc-pwrseq-emmc"; + reset-gpios = <&gpio BOOT_12 GPIO_ACTIVE_LOW>; + }; + hdmi-connector { compatible = "hdmi-connector"; type = "a"; @@ -164,6 +169,43 @@ pinctrl-names = "default"; }; +/* SD card */ +&sd_emmc_b { + status = "okay"; + pinctrl-0 = <&sdcard_c_pins>; + pinctrl-1 = <&sdcard_clk_gate_c_pins>; + pinctrl-names = "default", "clk-gate"; + + bus-width = <4>; + cap-sd-highspeed; + max-frequency = <50000000>; + disable-wp; + + cd-gpios = <&gpio GPIOC_6 GPIO_ACTIVE_LOW>; + vmmc-supply = <&vddao_3v3>; + vqmmc-supply = <&vddao_3v3>; +}; + +/* eMMC */ +&sd_emmc_c { + status = "okay"; + pinctrl-0 = <&emmc_pins>, <&emmc_ds_pins>; + pinctrl-1 = <&emmc_clk_gate_pins>; + pinctrl-names = "default", "clk-gate"; + + bus-width = <8>; + cap-mmc-highspeed; + mmc-ddr-1_8v; + mmc-hs200-1_8v; + max-frequency = <200000000>; + non-removable; + disable-wp; + + mmc-pwrseq = <&emmc_pwrseq>; + vmmc-supply = <&vcc_3v3>; + vqmmc-supply = <&flash_1v8>; +}; + &uart_AO { status = "okay"; pinctrl-0 = <&uart_ao_a_pins>; -- 2.20.1 _______________________________________________ linux-amlogic mailing list linux-amlogic@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-amlogic
next prev parent reply other threads:[~2019-05-14 9:16 UTC|newest] Thread overview: 19+ messages / expand[flat|nested] mbox.gz Atom feed top 2019-05-14 9:16 [PATCH 0/3] arm64: dts: meson: g12a: add mmc B and C Jerome Brunet 2019-05-14 9:16 ` Jerome Brunet 2019-05-14 9:16 ` [PATCH 1/3] arm64: dts: meson: g12a: add mmc nodes Jerome Brunet 2019-05-14 9:16 ` Jerome Brunet 2019-05-14 18:29 ` Martin Blumenstingl 2019-05-14 18:29 ` Martin Blumenstingl 2019-05-14 9:16 ` Jerome Brunet [this message] 2019-05-14 9:16 ` [PATCH 2/3] arm64: dts: meson: u200: add sd and emmc Jerome Brunet 2019-05-14 18:24 ` Martin Blumenstingl 2019-05-14 18:24 ` Martin Blumenstingl 2019-05-14 9:16 ` [PATCH 3/3] arm64: dts: meson: sei510: " Jerome Brunet 2019-05-14 9:16 ` Jerome Brunet 2019-05-14 18:24 ` Martin Blumenstingl 2019-05-14 18:24 ` Martin Blumenstingl 2019-05-14 10:21 ` [PATCH 0/3] arm64: dts: meson: g12a: add mmc B and C Neil Armstrong 2019-05-14 10:21 ` Neil Armstrong 2019-05-15 0:23 ` Kevin Hilman 2019-05-15 0:23 ` Kevin Hilman 2019-05-15 0:23 ` Kevin Hilman
Reply instructions: You may reply publicly to this message via plain-text email using any one of the following methods: * Save the following mbox file, import it into your mail client, and reply-to-all from there: mbox Avoid top-posting and favor interleaved quoting: https://en.wikipedia.org/wiki/Posting_style#Interleaved_style * Reply using the --to, --cc, and --in-reply-to switches of git-send-email(1): git send-email \ --in-reply-to=20190514091611.15278-3-jbrunet@baylibre.com \ --to=jbrunet@baylibre.com \ --cc=devicetree@vger.kernel.org \ --cc=khilman@baylibre.com \ --cc=linux-amlogic@lists.infradead.org \ --cc=linux-kernel@vger.kernel.org \ /path/to/YOUR_REPLY https://kernel.org/pub/software/scm/git/docs/git-send-email.html * If your mail client supports setting the In-Reply-To header via mailto: links, try the mailto: linkBe sure your reply has a Subject: header at the top and a blank line before the message body.
This is an external index of several public inboxes, see mirroring instructions on how to clone and mirror all data and code used by this external index.