From: Jagan Teki <jagan@amarulasolutions.com> To: Maxime Ripard <maxime.ripard@bootlin.com>, David Airlie <airlied@linux.ie>, Daniel Vetter <daniel@ffwll.ch>, Chen-Yu Tsai <wens@csie.org>, dri-devel@lists.freedesktop.org, linux-arm-kernel@lists.infradead.org, linux-kernel@vger.kernel.org Cc: Michael Trimarchi <michael@amarulasolutions.com>, devicetree@vger.kernel.org, linux-sunxi@googlegroups.com, linux-amarula@amarulasolutions.com, Sergey Suloev <ssuloev@orpaltech.com>, Ryan Pannell <ryan@osukl.com>, bshah@mykolab.com, Jagan Teki <jagan@amarulasolutions.com> Subject: [DO NOT MERGE] [PATCH v9 8/9] arm64: dts: allwinner: a64-pine64-lts: Enable Feiyang FY07024DI26A30-D DSI panel Date: Wed, 29 May 2019 16:26:14 +0530 [thread overview] Message-ID: <20190529105615.14027-9-jagan@amarulasolutions.com> (raw) In-Reply-To: <20190529105615.14027-1-jagan@amarulasolutions.com> Feiyang FY07024DI26A30-D MIPI_DSI panel is desiged to attach with DSI connector on pine64 boards, enable the same for pine64 LTS. DSI panel connected via board DSI port with, - DLDO1 as VCC-DSI supply - DC1SW as AVDD supply - DLDO2 as DVDD supply - PD24 gpio for reset pin - PH10 gpio for backlight enable pin Tested-by: Merlijn Wajer <merlijn@wizzup.org> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> --- .../allwinner/sun50i-a64-sopine-baseboard.dts | 31 +++++++++++++++++++ 1 file changed, 31 insertions(+) diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64-sopine-baseboard.dts b/arch/arm64/boot/dts/allwinner/sun50i-a64-sopine-baseboard.dts index e6fb9683f213..51b0cf71c3d4 100644 --- a/arch/arm64/boot/dts/allwinner/sun50i-a64-sopine-baseboard.dts +++ b/arch/arm64/boot/dts/allwinner/sun50i-a64-sopine-baseboard.dts @@ -46,6 +46,7 @@ /dts-v1/; #include "sun50i-a64-sopine.dtsi" +#include <dt-bindings/pwm/pwm.h> / { model = "SoPine with baseboard"; @@ -61,6 +62,14 @@ stdout-path = "serial0:115200n8"; }; + backlight: backlight { + compatible = "pwm-backlight"; + pwms = <&r_pwm 0 50000 PWM_POLARITY_INVERTED>; + brightness-levels = <1 2 4 8 16 32 64 128 255>; + default-brightness-level = <8>; + enable-gpios = <&pio 7 10 GPIO_ACTIVE_HIGH>; /* LCD-BL-EN: PH10 */ + }; + hdmi-connector { compatible = "hdmi-connector"; type = "a"; @@ -104,6 +113,24 @@ status = "okay"; }; +&dphy { + status = "okay"; +}; + +&dsi { + vcc-dsi-supply = <®_dldo1>; /* VCC-DSI */ + status = "okay"; + + panel@0 { + compatible = "feiyang,fy07024di26a30d"; + reg = <0>; + avdd-supply = <®_dc1sw>; /* VCC-LCD */ + dvdd-supply = <®_dldo2>; /* VCC-MIPI */ + reset-gpios = <&pio 3 24 GPIO_ACTIVE_HIGH>; /* LCD-RST: PD24 */ + backlight = <&backlight>; + }; +}; + &ehci0 { status = "okay"; }; @@ -184,6 +211,10 @@ vcc-hdmi-supply = <®_dldo1>; }; +&r_pwm { + status = "okay"; +}; + &sound { simple-audio-card,aux-devs = <&codec_analog>; simple-audio-card,widgets = "Microphone", "Microphone Jack", -- 2.18.0.321.gffc6fa0e3
WARNING: multiple messages have this Message-ID (diff)
From: Jagan Teki <jagan@amarulasolutions.com> To: Maxime Ripard <maxime.ripard@bootlin.com>, David Airlie <airlied@linux.ie>, Daniel Vetter <daniel@ffwll.ch>, Chen-Yu Tsai <wens@csie.org>, dri-devel@lists.freedesktop.org, linux-arm-kernel@lists.infradead.org, linux-kernel@vger.kernel.org Cc: devicetree@vger.kernel.org, Ryan Pannell <ryan@osukl.com>, bshah@mykolab.com, linux-sunxi@googlegroups.com, Jagan Teki <jagan@amarulasolutions.com>, Michael Trimarchi <michael@amarulasolutions.com>, linux-amarula@amarulasolutions.com, Sergey Suloev <ssuloev@orpaltech.com> Subject: [DO NOT MERGE] [PATCH v9 8/9] arm64: dts: allwinner: a64-pine64-lts: Enable Feiyang FY07024DI26A30-D DSI panel Date: Wed, 29 May 2019 16:26:14 +0530 [thread overview] Message-ID: <20190529105615.14027-9-jagan@amarulasolutions.com> (raw) In-Reply-To: <20190529105615.14027-1-jagan@amarulasolutions.com> Feiyang FY07024DI26A30-D MIPI_DSI panel is desiged to attach with DSI connector on pine64 boards, enable the same for pine64 LTS. DSI panel connected via board DSI port with, - DLDO1 as VCC-DSI supply - DC1SW as AVDD supply - DLDO2 as DVDD supply - PD24 gpio for reset pin - PH10 gpio for backlight enable pin Tested-by: Merlijn Wajer <merlijn@wizzup.org> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> --- .../allwinner/sun50i-a64-sopine-baseboard.dts | 31 +++++++++++++++++++ 1 file changed, 31 insertions(+) diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64-sopine-baseboard.dts b/arch/arm64/boot/dts/allwinner/sun50i-a64-sopine-baseboard.dts index e6fb9683f213..51b0cf71c3d4 100644 --- a/arch/arm64/boot/dts/allwinner/sun50i-a64-sopine-baseboard.dts +++ b/arch/arm64/boot/dts/allwinner/sun50i-a64-sopine-baseboard.dts @@ -46,6 +46,7 @@ /dts-v1/; #include "sun50i-a64-sopine.dtsi" +#include <dt-bindings/pwm/pwm.h> / { model = "SoPine with baseboard"; @@ -61,6 +62,14 @@ stdout-path = "serial0:115200n8"; }; + backlight: backlight { + compatible = "pwm-backlight"; + pwms = <&r_pwm 0 50000 PWM_POLARITY_INVERTED>; + brightness-levels = <1 2 4 8 16 32 64 128 255>; + default-brightness-level = <8>; + enable-gpios = <&pio 7 10 GPIO_ACTIVE_HIGH>; /* LCD-BL-EN: PH10 */ + }; + hdmi-connector { compatible = "hdmi-connector"; type = "a"; @@ -104,6 +113,24 @@ status = "okay"; }; +&dphy { + status = "okay"; +}; + +&dsi { + vcc-dsi-supply = <®_dldo1>; /* VCC-DSI */ + status = "okay"; + + panel@0 { + compatible = "feiyang,fy07024di26a30d"; + reg = <0>; + avdd-supply = <®_dc1sw>; /* VCC-LCD */ + dvdd-supply = <®_dldo2>; /* VCC-MIPI */ + reset-gpios = <&pio 3 24 GPIO_ACTIVE_HIGH>; /* LCD-RST: PD24 */ + backlight = <&backlight>; + }; +}; + &ehci0 { status = "okay"; }; @@ -184,6 +211,10 @@ vcc-hdmi-supply = <®_dldo1>; }; +&r_pwm { + status = "okay"; +}; + &sound { simple-audio-card,aux-devs = <&codec_analog>; simple-audio-card,widgets = "Microphone", "Microphone Jack", -- 2.18.0.321.gffc6fa0e3 _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
next prev parent reply other threads:[~2019-05-29 10:57 UTC|newest] Thread overview: 36+ messages / expand[flat|nested] mbox.gz Atom feed top 2019-05-29 10:56 [PATCH v9 0/9] drm/sun4i: Allwinner A64 MIPI-DSI support Jagan Teki 2019-05-29 10:56 ` Jagan Teki 2019-05-29 10:56 ` Jagan Teki 2019-05-29 10:56 ` [PATCH v9 1/9] dt-bindings: sun6i-dsi: Add A64 MIPI-DSI compatible Jagan Teki 2019-05-29 10:56 ` Jagan Teki 2019-05-31 6:59 ` Maxime Ripard 2019-05-31 6:59 ` Maxime Ripard 2019-05-31 6:59 ` Maxime Ripard 2019-05-31 7:21 ` Jagan Teki 2019-05-31 7:21 ` Jagan Teki 2019-05-29 10:56 ` [PATCH v9 2/9] dt-bindings: sun6i-dsi: Add A64 DPHY compatible (w/ A31 fallback) Jagan Teki 2019-05-29 10:56 ` Jagan Teki 2019-05-29 10:56 ` Jagan Teki 2019-05-31 7:00 ` Maxime Ripard 2019-05-31 7:00 ` Maxime Ripard 2019-05-31 7:00 ` Maxime Ripard 2019-05-29 10:56 ` [PATCH v9 3/9] drm/sun4i: dsi: Add has_mod_clk quirk Jagan Teki 2019-05-29 10:56 ` Jagan Teki 2019-05-29 10:56 ` [PATCH v9 4/9] drm/sun4i: dsi: Add Allwinner A64 MIPI DSI support Jagan Teki 2019-05-29 10:56 ` Jagan Teki 2019-05-29 10:56 ` [PATCH v9 5/9] arm64: dts: allwinner: a64: Add MIPI DSI pipeline Jagan Teki 2019-05-29 10:56 ` Jagan Teki 2019-05-29 10:56 ` Jagan Teki 2019-05-29 10:56 ` [PATCH v9 6/9] arm64: dts: allwinner: a64-amarula-relic: Add Techstar TS8550B MIPI-DSI panel Jagan Teki 2019-05-29 10:56 ` Jagan Teki 2019-05-29 10:56 ` [DO NOT MERGE] [PATCH v9 7/9] arm64: dts: allwinner: bananapi-m64: Enable Bananapi S070WV20-CT16 DSI panel Jagan Teki 2019-05-29 10:56 ` Jagan Teki 2019-05-29 10:56 ` Jagan Teki [this message] 2019-05-29 10:56 ` [DO NOT MERGE] [PATCH v9 8/9] arm64: dts: allwinner: a64-pine64-lts: Enable Feiyang FY07024DI26A30-D " Jagan Teki 2019-05-29 10:56 ` [DO NOT MERGE] [PATCH v9 9/9] arm64: dts: allwinner: oceanic-5205-5inmfd: Enable Microtech MTF050FHDI-03 panel Jagan Teki 2019-05-29 10:56 ` Jagan Teki 2019-05-31 6:58 ` [PATCH v9 0/9] drm/sun4i: Allwinner A64 MIPI-DSI support Maxime Ripard 2019-05-31 6:58 ` Maxime Ripard 2019-05-31 6:58 ` Maxime Ripard 2019-05-31 7:25 ` Jagan Teki 2019-05-31 7:25 ` Jagan Teki
Reply instructions: You may reply publicly to this message via plain-text email using any one of the following methods: * Save the following mbox file, import it into your mail client, and reply-to-all from there: mbox Avoid top-posting and favor interleaved quoting: https://en.wikipedia.org/wiki/Posting_style#Interleaved_style * Reply using the --to, --cc, and --in-reply-to switches of git-send-email(1): git send-email \ --in-reply-to=20190529105615.14027-9-jagan@amarulasolutions.com \ --to=jagan@amarulasolutions.com \ --cc=airlied@linux.ie \ --cc=bshah@mykolab.com \ --cc=daniel@ffwll.ch \ --cc=devicetree@vger.kernel.org \ --cc=dri-devel@lists.freedesktop.org \ --cc=linux-amarula@amarulasolutions.com \ --cc=linux-arm-kernel@lists.infradead.org \ --cc=linux-kernel@vger.kernel.org \ --cc=linux-sunxi@googlegroups.com \ --cc=maxime.ripard@bootlin.com \ --cc=michael@amarulasolutions.com \ --cc=ryan@osukl.com \ --cc=ssuloev@orpaltech.com \ --cc=wens@csie.org \ /path/to/YOUR_REPLY https://kernel.org/pub/software/scm/git/docs/git-send-email.html * If your mail client supports setting the In-Reply-To header via mailto: links, try the mailto: linkBe sure your reply has a Subject: header at the top and a blank line before the message body.
This is an external index of several public inboxes, see mirroring instructions on how to clone and mirror all data and code used by this external index.