[PATCH v7 10/14] dt-bindings: Document the Rockchip ISP1 bindings

[Helen Koike <helen.koike@collabora.com>]

From: Jacob Chen <jacob2.chen@rock-chips.com>

Add DT bindings documentation for Rockchip ISP1

Signed-off-by: Jacob Chen <jacob2.chen@rock-chips.com>
Reviewed-by: Rob Herring <robh@kernel.org>
[update for upstream]
Signed-off-by: Helen Koike <helen.koike@collabora.com>

---

Changes in v7:
- update document with new design and tested example

 .../bindings/media/rockchip-isp1.txt          | 71 +++++++++++++++++++
 1 file changed, 71 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/media/rockchip-isp1.txt

diff --git a/Documentation/devicetree/bindings/media/rockchip-isp1.txt b/Documentation/devicetree/bindings/media/rockchip-isp1.txt
new file mode 100644
index 000000000000..a97fef0f189f
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/rockchip-isp1.txt
@@ -0,0 +1,71 @@
+Rockchip SoC Image Signal Processing unit v1
+----------------------------------------------
+
+Rockchip ISP1 is the Camera interface for the Rockchip series of SoCs
+which contains image processing, scaling, and compression funcitons.
+
+Required properties:
+- compatible: value should be one of the following
+	"rockchip,rk3288-cif-isp";
+	"rockchip,rk3399-cif-isp";
+- reg : offset and length of the register set for the device.
+- interrupts: should contain ISP interrupt.
+- clocks: phandle to the required clocks.
+- clock-names: required clock name.
+- iommus: required a iommu node.
+- phys: the phandle for the PHY port
+- phy-names: must contain "dphy"
+
+port node
+-------------------
+
+The device node should contain one 'ports' child node, with children 'port'
+with child 'endpoint'.
+nodes, according to the bindings defined in Documentation/devicetree/bindings/
+media/video-interfaces.txt.
+
+- endpoint(mipi):
+	- remote-endpoint: Connecting to Rockchip MIPI-DPHY,
+		which is defined in rockchip-mipi-dphy.txt.
+
+The port node must contain at least one endpoint, either parallel or mipi.
+It could have multiple endpoints, but please note the hardware don't support
+two sensors work at a time, they are supposed to work asynchronously.
+
+Device node example
+-------------------
+
+	isp0: isp0@ff910000 {
+		compatible = "rockchip,rk3399-cif-isp";
+		reg = <0x0 0xff910000 0x0 0x4000>;
+		interrupts = <GIC_SPI 43 IRQ_TYPE_LEVEL_HIGH 0>;
+		clocks = <&cru SCLK_ISP0>,
+			 <&cru ACLK_ISP0>, <&cru ACLK_ISP0_WRAPPER>,
+			 <&cru HCLK_ISP0>, <&cru HCLK_ISP0_WRAPPER>;
+		clock-names = "clk_isp",
+			      "aclk_isp", "aclk_isp_wrap",
+			      "hclk_isp", "hclk_isp_wrap";
+		power-domains = <&power RK3399_PD_ISP0>;
+		iommus = <&isp0_mmu>;
+		phys = <&dphy>;
+		phy-names = "dphy";
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				mipi_in_wcam: endpoint@0 {
+					reg = <0>;
+					remote-endpoint = <&wcam_out>;
+					data-lanes = <1 2>;
+				};
+
+				mipi_in_ucam: endpoint@1 {
+					reg = <1>;
+					remote-endpoint = <&ucam_out>;
+					data-lanes = <1>;
+				};
+			};
+		};
+	};
-- 
2.20.1