From: Miquel Raynal <miquel.raynal@bootlin.com> To: Gregory Clement <gregory.clement@bootlin.com>, Jason Cooper <jason@lakedaemon.net>, Andrew Lunn <andrew@lunn.ch>, Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>, Kishon Vijay Abraham I <kishon@ti.com> Cc: devicetree@vger.kernel.org, Antoine Tenart <antoine.tenart@bootlin.com>, Grzegorz Jaszczyk <jaz@semihalf.com>, Russell King <linux@armlinux.org.uk>, Maxime Chevallier <maxime.chevallier@bootlin.com>, Nadav Haklai <nadavh@marvell.com>, Rob Herring <robh+dt@kernel.org>, Thomas Petazzoni <thomas.petazzoni@bootlin.com>, Miquel Raynal <miquel.raynal@bootlin.com>, linux-arm-kernel@lists.infradead.org Subject: [PATCH v3 11/19] phy: mvebu-cp110-comphy: Add PCIe support Date: Wed, 31 Jul 2019 14:21:18 +0200 [thread overview] Message-ID: <20190731122126.3049-12-miquel.raynal@bootlin.com> (raw) In-Reply-To: <20190731122126.3049-1-miquel.raynal@bootlin.com> From: Grzegorz Jaszczyk <jaz@semihalf.com> Add PCIe support by filling the COMPHY modes table. Also add a new macro to generate the right value for the firmware depending on the width (PCI x1, x2, x4, etc). The width will be passed by the core as the "submode" argument of the ->set_mode() callback. If this argument is zero, default to x1 mode. Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com> [miquel.raynal@bootlin.com: adapt the content to the mainline driver] Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> --- drivers/phy/marvell/phy-mvebu-cp110-comphy.c | 37 +++++++++++++++++--- 1 file changed, 32 insertions(+), 5 deletions(-) diff --git a/drivers/phy/marvell/phy-mvebu-cp110-comphy.c b/drivers/phy/marvell/phy-mvebu-cp110-comphy.c index c61469ed7cbe..076b2bfa8e7b 100644 --- a/drivers/phy/marvell/phy-mvebu-cp110-comphy.c +++ b/drivers/phy/marvell/phy-mvebu-cp110-comphy.c @@ -128,6 +128,7 @@ * [ 5-11]: COMPHY port index * [12-16]: COMPHY mode * [17]: Clock source + * [18-20]: PCIe width (x1, x2, x4) */ #define COMPHY_FW_POL_OFFSET 0 #define COMPHY_FW_POL_MASK GENMASK(1, 0) @@ -142,24 +143,31 @@ #define COMPHY_FW_PORT_MASK GENMASK(11, 8) #define COMPHY_FW_MODE_OFFSET 12 #define COMPHY_FW_MODE_MASK GENMASK(16, 12) +#define COMPHY_FW_WIDTH_OFFSET 18 +#define COMPHY_FW_WIDTH_MASK GENMASK(20, 18) -#define COMPHY_FW_PARAM_FULL(mode, port, speed, pol) \ +#define COMPHY_FW_PARAM_FULL(mode, port, speed, pol, width) \ ((((pol) << COMPHY_FW_POL_OFFSET) & COMPHY_FW_POL_MASK) | \ (((mode) << COMPHY_FW_MODE_OFFSET) & COMPHY_FW_MODE_MASK) | \ (((port) << COMPHY_FW_PORT_OFFSET) & COMPHY_FW_PORT_MASK) | \ - (((speed) << COMPHY_FW_SPEED_OFFSET) & COMPHY_FW_SPEED_MASK)) + (((speed) << COMPHY_FW_SPEED_OFFSET) & COMPHY_FW_SPEED_MASK) | \ + (((width) << COMPHY_FW_WIDTH_OFFSET) & COMPHY_FW_WIDTH_MASK)) #define COMPHY_FW_PARAM(mode, port) \ - COMPHY_FW_PARAM_FULL(mode, port, 0, 0) + COMPHY_FW_PARAM_FULL(mode, port, COMPHY_FW_SPEED_MAX, 0, 0) #define COMPHY_FW_PARAM_ETH(mode, port, speed) \ - COMPHY_FW_PARAM_FULL(mode, port, speed, 0) + COMPHY_FW_PARAM_FULL(mode, port, speed, 0, 0) + +#define COMPHY_FW_PARAM_PCIE(mode, port, width) \ + COMPHY_FW_PARAM_FULL(mode, port, COMPHY_FW_SPEED_5000, 0, width) #define COMPHY_FW_MODE_SATA 0x1 #define COMPHY_FW_MODE_SGMII 0x2 /* SGMII 1G */ #define COMPHY_FW_MODE_HS_SGMII 0x3 /* SGMII 2.5G */ #define COMPHY_FW_MODE_USB3H 0x4 #define COMPHY_FW_MODE_USB3D 0x5 +#define COMPHY_FW_MODE_PCIE 0x6 #define COMPHY_FW_MODE_RXAUI 0x7 #define COMPHY_FW_MODE_XFI 0x8 /* SFI: 0x9 (is treated like XFI) */ @@ -194,6 +202,7 @@ struct mvebu_comphy_conf { static const struct mvebu_comphy_conf mvebu_comphy_cp110_modes[] = { /* lane 0 */ + GEN_CONF(0, 0, PHY_MODE_PCIE, COMPHY_FW_MODE_PCIE), ETH_CONF(0, 1, PHY_INTERFACE_MODE_SGMII, 0x1, COMPHY_FW_MODE_SGMII), ETH_CONF(0, 1, PHY_INTERFACE_MODE_2500BASEX, 0x1, COMPHY_FW_MODE_HS_SGMII), GEN_CONF(0, 1, PHY_MODE_SATA, COMPHY_FW_MODE_SATA), @@ -201,6 +210,7 @@ static const struct mvebu_comphy_conf mvebu_comphy_cp110_modes[] = { GEN_CONF(1, 0, PHY_MODE_USB_HOST_SS, COMPHY_FW_MODE_USB3H), GEN_CONF(1, 0, PHY_MODE_USB_DEVICE_SS, COMPHY_FW_MODE_USB3D), GEN_CONF(1, 0, PHY_MODE_SATA, COMPHY_FW_MODE_SATA), + GEN_CONF(1, 0, PHY_MODE_PCIE, COMPHY_FW_MODE_PCIE), ETH_CONF(1, 2, PHY_INTERFACE_MODE_SGMII, 0x1, COMPHY_FW_MODE_SGMII), ETH_CONF(1, 2, PHY_INTERFACE_MODE_2500BASEX, 0x1, COMPHY_FW_MODE_HS_SGMII), /* lane 2 */ @@ -210,7 +220,9 @@ static const struct mvebu_comphy_conf mvebu_comphy_cp110_modes[] = { ETH_CONF(2, 0, PHY_INTERFACE_MODE_10GKR, 0x1, COMPHY_FW_MODE_XFI), GEN_CONF(2, 0, PHY_MODE_USB_HOST_SS, COMPHY_FW_MODE_USB3H), GEN_CONF(2, 0, PHY_MODE_SATA, COMPHY_FW_MODE_SATA), + GEN_CONF(2, 0, PHY_MODE_PCIE, COMPHY_FW_MODE_PCIE), /* lane 3 */ + GEN_CONF(3, 0, PHY_MODE_PCIE, COMPHY_FW_MODE_PCIE), ETH_CONF(3, 1, PHY_INTERFACE_MODE_SGMII, 0x2, COMPHY_FW_MODE_SGMII), ETH_CONF(3, 1, PHY_INTERFACE_MODE_2500BASEX, 0x2, COMPHY_FW_MODE_HS_SGMII), ETH_CONF(3, 1, PHY_INTERFACE_MODE_RXAUI, -1, COMPHY_FW_MODE_RXAUI), @@ -223,6 +235,7 @@ static const struct mvebu_comphy_conf mvebu_comphy_cp110_modes[] = { ETH_CONF(4, 0, PHY_INTERFACE_MODE_RXAUI, -1, COMPHY_FW_MODE_RXAUI), GEN_CONF(4, 0, PHY_MODE_USB_DEVICE_SS, COMPHY_FW_MODE_USB3D), GEN_CONF(4, 1, PHY_MODE_USB_HOST_SS, COMPHY_FW_MODE_USB3H), + GEN_CONF(4, 1, PHY_MODE_PCIE, COMPHY_FW_MODE_PCIE), ETH_CONF(4, 1, PHY_INTERFACE_MODE_SGMII, 0x1, COMPHY_FW_MODE_SGMII), ETH_CONF(4, 1, PHY_INTERFACE_MODE_2500BASEX, -1, COMPHY_FW_MODE_HS_SGMII), ETH_CONF(4, 1, PHY_INTERFACE_MODE_10GKR, -1, COMPHY_FW_MODE_XFI), @@ -231,6 +244,7 @@ static const struct mvebu_comphy_conf mvebu_comphy_cp110_modes[] = { GEN_CONF(5, 1, PHY_MODE_SATA, COMPHY_FW_MODE_SATA), ETH_CONF(5, 2, PHY_INTERFACE_MODE_SGMII, 0x1, COMPHY_FW_MODE_SGMII), ETH_CONF(5, 2, PHY_INTERFACE_MODE_2500BASEX, 0x1, COMPHY_FW_MODE_HS_SGMII), + GEN_CONF(5, 2, PHY_MODE_PCIE, COMPHY_FW_MODE_PCIE), }; struct mvebu_comphy_priv { @@ -265,6 +279,8 @@ static int mvebu_comphy_get_mode(bool fw_mode, int lane, int port, enum phy_mode mode, int submode) { int i, n = ARRAY_SIZE(mvebu_comphy_cp110_modes); + /* Ignore PCIe submode: it represents the width */ + bool ignore_submode = (mode == PHY_MODE_PCIE); const struct mvebu_comphy_conf *conf; /* Unused PHY mux value is 0x0 */ @@ -276,7 +292,7 @@ static int mvebu_comphy_get_mode(bool fw_mode, int lane, int port, if (conf->lane == lane && conf->port == port && conf->mode == mode && - conf->submode == submode) + (conf->submode == submode || ignore_submode)) break; } @@ -678,6 +694,12 @@ static int mvebu_comphy_power_on(struct phy *phy) dev_dbg(priv->dev, "set lane %d to SATA mode\n", lane->id); fw_param = COMPHY_FW_PARAM(fw_mode, lane->port); break; + case PHY_MODE_PCIE: + dev_dbg(priv->dev, "set lane %d to PCIe mode (x%d)\n", lane->id, + lane->submode); + fw_param = COMPHY_FW_PARAM_PCIE(fw_mode, lane->port, + lane->submode); + break; default: dev_err(priv->dev, "unsupported PHY mode (%d)\n", lane->mode); return -ENOTSUPP; @@ -714,6 +736,11 @@ static int mvebu_comphy_set_mode(struct phy *phy, lane->mode = mode; lane->submode = submode; + + /* PCIe submode represents the width */ + if (mode == PHY_MODE_PCIE && !lane->submode) + lane->submode = 1; + return 0; } -- 2.20.1
WARNING: multiple messages have this Message-ID (diff)
From: Miquel Raynal <miquel.raynal@bootlin.com> To: Gregory Clement <gregory.clement@bootlin.com>, Jason Cooper <jason@lakedaemon.net>, Andrew Lunn <andrew@lunn.ch>, Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>, Kishon Vijay Abraham I <kishon@ti.com> Cc: devicetree@vger.kernel.org, Antoine Tenart <antoine.tenart@bootlin.com>, Grzegorz Jaszczyk <jaz@semihalf.com>, Russell King <linux@armlinux.org.uk>, Maxime Chevallier <maxime.chevallier@bootlin.com>, Nadav Haklai <nadavh@marvell.com>, Rob Herring <robh+dt@kernel.org>, Thomas Petazzoni <thomas.petazzoni@bootlin.com>, Miquel Raynal <miquel.raynal@bootlin.com>, linux-arm-kernel@lists.infradead.org Subject: [PATCH v3 11/19] phy: mvebu-cp110-comphy: Add PCIe support Date: Wed, 31 Jul 2019 14:21:18 +0200 [thread overview] Message-ID: <20190731122126.3049-12-miquel.raynal@bootlin.com> (raw) In-Reply-To: <20190731122126.3049-1-miquel.raynal@bootlin.com> From: Grzegorz Jaszczyk <jaz@semihalf.com> Add PCIe support by filling the COMPHY modes table. Also add a new macro to generate the right value for the firmware depending on the width (PCI x1, x2, x4, etc). The width will be passed by the core as the "submode" argument of the ->set_mode() callback. If this argument is zero, default to x1 mode. Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com> [miquel.raynal@bootlin.com: adapt the content to the mainline driver] Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> --- drivers/phy/marvell/phy-mvebu-cp110-comphy.c | 37 +++++++++++++++++--- 1 file changed, 32 insertions(+), 5 deletions(-) diff --git a/drivers/phy/marvell/phy-mvebu-cp110-comphy.c b/drivers/phy/marvell/phy-mvebu-cp110-comphy.c index c61469ed7cbe..076b2bfa8e7b 100644 --- a/drivers/phy/marvell/phy-mvebu-cp110-comphy.c +++ b/drivers/phy/marvell/phy-mvebu-cp110-comphy.c @@ -128,6 +128,7 @@ * [ 5-11]: COMPHY port index * [12-16]: COMPHY mode * [17]: Clock source + * [18-20]: PCIe width (x1, x2, x4) */ #define COMPHY_FW_POL_OFFSET 0 #define COMPHY_FW_POL_MASK GENMASK(1, 0) @@ -142,24 +143,31 @@ #define COMPHY_FW_PORT_MASK GENMASK(11, 8) #define COMPHY_FW_MODE_OFFSET 12 #define COMPHY_FW_MODE_MASK GENMASK(16, 12) +#define COMPHY_FW_WIDTH_OFFSET 18 +#define COMPHY_FW_WIDTH_MASK GENMASK(20, 18) -#define COMPHY_FW_PARAM_FULL(mode, port, speed, pol) \ +#define COMPHY_FW_PARAM_FULL(mode, port, speed, pol, width) \ ((((pol) << COMPHY_FW_POL_OFFSET) & COMPHY_FW_POL_MASK) | \ (((mode) << COMPHY_FW_MODE_OFFSET) & COMPHY_FW_MODE_MASK) | \ (((port) << COMPHY_FW_PORT_OFFSET) & COMPHY_FW_PORT_MASK) | \ - (((speed) << COMPHY_FW_SPEED_OFFSET) & COMPHY_FW_SPEED_MASK)) + (((speed) << COMPHY_FW_SPEED_OFFSET) & COMPHY_FW_SPEED_MASK) | \ + (((width) << COMPHY_FW_WIDTH_OFFSET) & COMPHY_FW_WIDTH_MASK)) #define COMPHY_FW_PARAM(mode, port) \ - COMPHY_FW_PARAM_FULL(mode, port, 0, 0) + COMPHY_FW_PARAM_FULL(mode, port, COMPHY_FW_SPEED_MAX, 0, 0) #define COMPHY_FW_PARAM_ETH(mode, port, speed) \ - COMPHY_FW_PARAM_FULL(mode, port, speed, 0) + COMPHY_FW_PARAM_FULL(mode, port, speed, 0, 0) + +#define COMPHY_FW_PARAM_PCIE(mode, port, width) \ + COMPHY_FW_PARAM_FULL(mode, port, COMPHY_FW_SPEED_5000, 0, width) #define COMPHY_FW_MODE_SATA 0x1 #define COMPHY_FW_MODE_SGMII 0x2 /* SGMII 1G */ #define COMPHY_FW_MODE_HS_SGMII 0x3 /* SGMII 2.5G */ #define COMPHY_FW_MODE_USB3H 0x4 #define COMPHY_FW_MODE_USB3D 0x5 +#define COMPHY_FW_MODE_PCIE 0x6 #define COMPHY_FW_MODE_RXAUI 0x7 #define COMPHY_FW_MODE_XFI 0x8 /* SFI: 0x9 (is treated like XFI) */ @@ -194,6 +202,7 @@ struct mvebu_comphy_conf { static const struct mvebu_comphy_conf mvebu_comphy_cp110_modes[] = { /* lane 0 */ + GEN_CONF(0, 0, PHY_MODE_PCIE, COMPHY_FW_MODE_PCIE), ETH_CONF(0, 1, PHY_INTERFACE_MODE_SGMII, 0x1, COMPHY_FW_MODE_SGMII), ETH_CONF(0, 1, PHY_INTERFACE_MODE_2500BASEX, 0x1, COMPHY_FW_MODE_HS_SGMII), GEN_CONF(0, 1, PHY_MODE_SATA, COMPHY_FW_MODE_SATA), @@ -201,6 +210,7 @@ static const struct mvebu_comphy_conf mvebu_comphy_cp110_modes[] = { GEN_CONF(1, 0, PHY_MODE_USB_HOST_SS, COMPHY_FW_MODE_USB3H), GEN_CONF(1, 0, PHY_MODE_USB_DEVICE_SS, COMPHY_FW_MODE_USB3D), GEN_CONF(1, 0, PHY_MODE_SATA, COMPHY_FW_MODE_SATA), + GEN_CONF(1, 0, PHY_MODE_PCIE, COMPHY_FW_MODE_PCIE), ETH_CONF(1, 2, PHY_INTERFACE_MODE_SGMII, 0x1, COMPHY_FW_MODE_SGMII), ETH_CONF(1, 2, PHY_INTERFACE_MODE_2500BASEX, 0x1, COMPHY_FW_MODE_HS_SGMII), /* lane 2 */ @@ -210,7 +220,9 @@ static const struct mvebu_comphy_conf mvebu_comphy_cp110_modes[] = { ETH_CONF(2, 0, PHY_INTERFACE_MODE_10GKR, 0x1, COMPHY_FW_MODE_XFI), GEN_CONF(2, 0, PHY_MODE_USB_HOST_SS, COMPHY_FW_MODE_USB3H), GEN_CONF(2, 0, PHY_MODE_SATA, COMPHY_FW_MODE_SATA), + GEN_CONF(2, 0, PHY_MODE_PCIE, COMPHY_FW_MODE_PCIE), /* lane 3 */ + GEN_CONF(3, 0, PHY_MODE_PCIE, COMPHY_FW_MODE_PCIE), ETH_CONF(3, 1, PHY_INTERFACE_MODE_SGMII, 0x2, COMPHY_FW_MODE_SGMII), ETH_CONF(3, 1, PHY_INTERFACE_MODE_2500BASEX, 0x2, COMPHY_FW_MODE_HS_SGMII), ETH_CONF(3, 1, PHY_INTERFACE_MODE_RXAUI, -1, COMPHY_FW_MODE_RXAUI), @@ -223,6 +235,7 @@ static const struct mvebu_comphy_conf mvebu_comphy_cp110_modes[] = { ETH_CONF(4, 0, PHY_INTERFACE_MODE_RXAUI, -1, COMPHY_FW_MODE_RXAUI), GEN_CONF(4, 0, PHY_MODE_USB_DEVICE_SS, COMPHY_FW_MODE_USB3D), GEN_CONF(4, 1, PHY_MODE_USB_HOST_SS, COMPHY_FW_MODE_USB3H), + GEN_CONF(4, 1, PHY_MODE_PCIE, COMPHY_FW_MODE_PCIE), ETH_CONF(4, 1, PHY_INTERFACE_MODE_SGMII, 0x1, COMPHY_FW_MODE_SGMII), ETH_CONF(4, 1, PHY_INTERFACE_MODE_2500BASEX, -1, COMPHY_FW_MODE_HS_SGMII), ETH_CONF(4, 1, PHY_INTERFACE_MODE_10GKR, -1, COMPHY_FW_MODE_XFI), @@ -231,6 +244,7 @@ static const struct mvebu_comphy_conf mvebu_comphy_cp110_modes[] = { GEN_CONF(5, 1, PHY_MODE_SATA, COMPHY_FW_MODE_SATA), ETH_CONF(5, 2, PHY_INTERFACE_MODE_SGMII, 0x1, COMPHY_FW_MODE_SGMII), ETH_CONF(5, 2, PHY_INTERFACE_MODE_2500BASEX, 0x1, COMPHY_FW_MODE_HS_SGMII), + GEN_CONF(5, 2, PHY_MODE_PCIE, COMPHY_FW_MODE_PCIE), }; struct mvebu_comphy_priv { @@ -265,6 +279,8 @@ static int mvebu_comphy_get_mode(bool fw_mode, int lane, int port, enum phy_mode mode, int submode) { int i, n = ARRAY_SIZE(mvebu_comphy_cp110_modes); + /* Ignore PCIe submode: it represents the width */ + bool ignore_submode = (mode == PHY_MODE_PCIE); const struct mvebu_comphy_conf *conf; /* Unused PHY mux value is 0x0 */ @@ -276,7 +292,7 @@ static int mvebu_comphy_get_mode(bool fw_mode, int lane, int port, if (conf->lane == lane && conf->port == port && conf->mode == mode && - conf->submode == submode) + (conf->submode == submode || ignore_submode)) break; } @@ -678,6 +694,12 @@ static int mvebu_comphy_power_on(struct phy *phy) dev_dbg(priv->dev, "set lane %d to SATA mode\n", lane->id); fw_param = COMPHY_FW_PARAM(fw_mode, lane->port); break; + case PHY_MODE_PCIE: + dev_dbg(priv->dev, "set lane %d to PCIe mode (x%d)\n", lane->id, + lane->submode); + fw_param = COMPHY_FW_PARAM_PCIE(fw_mode, lane->port, + lane->submode); + break; default: dev_err(priv->dev, "unsupported PHY mode (%d)\n", lane->mode); return -ENOTSUPP; @@ -714,6 +736,11 @@ static int mvebu_comphy_set_mode(struct phy *phy, lane->mode = mode; lane->submode = submode; + + /* PCIe submode represents the width */ + if (mode == PHY_MODE_PCIE && !lane->submode) + lane->submode = 1; + return 0; } -- 2.20.1 _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
next prev parent reply other threads:[~2019-07-31 12:21 UTC|newest] Thread overview: 53+ messages / expand[flat|nested] mbox.gz Atom feed top 2019-07-31 12:21 [PATCH v3 00/19] Enhance CP110 COMPHY support Miquel Raynal 2019-07-31 12:21 ` [PATCH v3 01/19] phy: mvebu-cp110-comphy: Add clocks support Miquel Raynal 2019-07-31 12:21 ` Miquel Raynal 2019-07-31 12:21 ` [PATCH v3 02/19] phy: mvebu-cp110-comphy: Explicitly initialize the lane submode Miquel Raynal 2019-07-31 12:21 ` Miquel Raynal 2019-07-31 12:21 ` [PATCH v3 03/19] phy: mvebu-cp110-comphy: Add SMC call support Miquel Raynal 2019-07-31 12:21 ` Miquel Raynal 2019-07-31 12:21 ` [PATCH v3 04/19] phy: mvebu-cp110-comphy: List already supported Ethernet modes Miquel Raynal 2019-07-31 12:21 ` Miquel Raynal 2019-07-31 12:21 ` [PATCH v3 05/19] phy: mvebu-cp110-comphy: Add RXAUI support Miquel Raynal 2019-07-31 12:21 ` Miquel Raynal 2019-07-31 12:21 ` [PATCH v3 06/19] phy: mvebu-cp110-comphy: Rename the macro handling only Ethernet modes Miquel Raynal 2019-07-31 12:21 ` Miquel Raynal 2019-07-31 12:21 ` [PATCH v3 07/19] phy: mvebu-cp110-comphy: Allow non-Ethernet modes to be configured Miquel Raynal 2019-07-31 12:21 ` Miquel Raynal 2019-07-31 12:21 ` [PATCH v3 08/19] phy: mvebu-cp110-comphy: Add USB3 host/device support Miquel Raynal 2019-07-31 12:21 ` Miquel Raynal 2019-07-31 12:21 ` [PATCH v3 09/19] phy: mvebu-cp110-comphy: Add SATA support Miquel Raynal 2019-07-31 12:21 ` Miquel Raynal 2019-07-31 12:21 ` [PATCH v3 10/19] phy: mvebu-cp110-comphy: Cosmetic change in a helper Miquel Raynal 2019-07-31 12:21 ` Miquel Raynal 2019-07-31 12:21 ` Miquel Raynal [this message] 2019-07-31 12:21 ` [PATCH v3 11/19] phy: mvebu-cp110-comphy: Add PCIe support Miquel Raynal 2019-07-31 12:21 ` [PATCH v3 12/19] phy: mvebu-cp110-comphy: Update comment about powering off all lanes at boot Miquel Raynal 2019-07-31 12:21 ` Miquel Raynal 2019-07-31 12:21 ` [PATCH v3 13/19] dt-bindings: phy: Add Marvell COMPHY clocks Miquel Raynal 2019-07-31 12:21 ` Miquel Raynal 2019-08-12 21:29 ` Rob Herring 2019-08-12 21:29 ` Rob Herring 2019-08-19 8:40 ` Miquel Raynal 2019-07-31 12:21 ` [PATCH v3 14/19] dt-bindings: pci: add PHY properties to Armada 7K/8K controller bindings Miquel Raynal 2019-07-31 12:21 ` Miquel Raynal 2019-08-21 18:28 ` Rob Herring 2019-08-21 18:28 ` Rob Herring 2019-08-24 10:15 ` Miquel Raynal 2019-07-31 12:21 ` [PATCH v3 15/19] arm64: dts: marvell: Add CP110 COMPHY clocks Miquel Raynal 2019-07-31 12:21 ` Miquel Raynal 2019-07-31 12:21 ` [PATCH v3 16/19] arm64: dts: marvell: Add 7k/8k per-port PHYs in SATA nodes Miquel Raynal 2019-07-31 12:21 ` Miquel Raynal 2019-07-31 12:21 ` [PATCH v3 17/19] arm64: dts: marvell: Add 7k/8k PHYs in USB3 nodes Miquel Raynal 2019-07-31 12:21 ` Miquel Raynal 2019-07-31 12:21 ` [PATCH v3 18/19] arm64: dts: marvell: Add 7k/8k PHYs in PCIe nodes Miquel Raynal 2019-07-31 12:21 ` Miquel Raynal 2019-07-31 12:21 ` [PATCH v3 19/19] arm64: dts: marvell: Convert 7k/8k usb-phy properties to phy-supply Miquel Raynal 2019-07-31 12:21 ` Miquel Raynal 2019-08-23 3:16 ` [PATCH v3 00/19] Enhance CP110 COMPHY support Kishon Vijay Abraham I 2019-08-23 7:33 ` Miquel Raynal 2019-08-24 11:54 ` Miquel Raynal 2019-08-26 11:51 ` Kishon Vijay Abraham I 2019-08-26 11:51 ` Kishon Vijay Abraham I 2019-08-26 12:23 ` Miquel Raynal 2019-08-27 14:22 ` Gregory CLEMENT 2019-08-27 14:22 ` Gregory CLEMENT
Reply instructions: You may reply publicly to this message via plain-text email using any one of the following methods: * Save the following mbox file, import it into your mail client, and reply-to-all from there: mbox Avoid top-posting and favor interleaved quoting: https://en.wikipedia.org/wiki/Posting_style#Interleaved_style * Reply using the --to, --cc, and --in-reply-to switches of git-send-email(1): git send-email \ --in-reply-to=20190731122126.3049-12-miquel.raynal@bootlin.com \ --to=miquel.raynal@bootlin.com \ --cc=andrew@lunn.ch \ --cc=antoine.tenart@bootlin.com \ --cc=devicetree@vger.kernel.org \ --cc=gregory.clement@bootlin.com \ --cc=jason@lakedaemon.net \ --cc=jaz@semihalf.com \ --cc=kishon@ti.com \ --cc=linux-arm-kernel@lists.infradead.org \ --cc=linux@armlinux.org.uk \ --cc=maxime.chevallier@bootlin.com \ --cc=nadavh@marvell.com \ --cc=robh+dt@kernel.org \ --cc=sebastian.hesselbarth@gmail.com \ --cc=thomas.petazzoni@bootlin.com \ /path/to/YOUR_REPLY https://kernel.org/pub/software/scm/git/docs/git-send-email.html * If your mail client supports setting the In-Reply-To header via mailto: links, try the mailto: linkBe sure your reply has a Subject: header at the top and a blank line before the message body.
This is an external index of several public inboxes, see mirroring instructions on how to clone and mirror all data and code used by this external index.