From: Arnd Bergmann <arnd@arndb.de>
To: soc@kernel.org
Cc: Arnd Bergmann <arnd@arndb.de>,
Linus Walleij <linus.walleij@linaro.org>,
Bartosz Golaszewski <bgolaszewski@baylibre.com>,
linux-kernel@vger.kernel.org, linux-gpio@vger.kernel.org
Subject: [PATCH 03/16] gpio: remove ks8695 driver
Date: Fri, 9 Aug 2019 22:27:31 +0200 [thread overview]
Message-ID: <20190809202749.742267-4-arnd@arndb.de> (raw)
In-Reply-To: <20190809202749.742267-1-arnd@arndb.de>
The platform is getting removed, so there are no remaining
users of this driver.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
---
drivers/gpio/Makefile | 1 -
drivers/gpio/gpio-ks8695.c | 284 -------------------------------------
2 files changed, 285 deletions(-)
delete mode 100644 drivers/gpio/gpio-ks8695.c
diff --git a/drivers/gpio/Makefile b/drivers/gpio/Makefile
index a4e91175c708..65d74084c9b2 100644
--- a/drivers/gpio/Makefile
+++ b/drivers/gpio/Makefile
@@ -67,7 +67,6 @@ obj-$(CONFIG_GPIO_IT87) += gpio-it87.o
obj-$(CONFIG_GPIO_IXP4XX) += gpio-ixp4xx.o
obj-$(CONFIG_GPIO_JANZ_TTL) += gpio-janz-ttl.o
obj-$(CONFIG_GPIO_KEMPLD) += gpio-kempld.o
-obj-$(CONFIG_ARCH_KS8695) += gpio-ks8695.o
obj-$(CONFIG_GPIO_LOONGSON1) += gpio-loongson1.o
obj-$(CONFIG_GPIO_LOONGSON) += gpio-loongson.o
obj-$(CONFIG_GPIO_LP3943) += gpio-lp3943.o
diff --git a/drivers/gpio/gpio-ks8695.c b/drivers/gpio/gpio-ks8695.c
deleted file mode 100644
index a0f87c124894..000000000000
--- a/drivers/gpio/gpio-ks8695.c
+++ /dev/null
@@ -1,284 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-only
-/*
- * arch/arm/mach-ks8695/gpio.c
- *
- * Copyright (C) 2006 Andrew Victor
- * Updated to GPIOLIB, Copyright 2008 Simtec Electronics
- * Daniel Silverstone <dsilvers@simtec.co.uk>
- */
-#include <linux/gpio/driver.h>
-#include <linux/kernel.h>
-#include <linux/mm.h>
-#include <linux/init.h>
-#include <linux/debugfs.h>
-#include <linux/seq_file.h>
-#include <linux/module.h>
-#include <linux/io.h>
-
-#include <mach/hardware.h>
-#include <asm/mach/irq.h>
-
-#include <mach/regs-gpio.h>
-#include <mach/gpio-ks8695.h>
-
-/*
- * Configure a GPIO line for either GPIO function, or its internal
- * function (Interrupt, Timer, etc).
- */
-static void ks8695_gpio_mode(unsigned int pin, short gpio)
-{
- unsigned int enable[] = { IOPC_IOEINT0EN, IOPC_IOEINT1EN, IOPC_IOEINT2EN, IOPC_IOEINT3EN, IOPC_IOTIM0EN, IOPC_IOTIM1EN };
- unsigned long x, flags;
-
- if (pin > KS8695_GPIO_5) /* only GPIO 0..5 have internal functions */
- return;
-
- local_irq_save(flags);
-
- x = __raw_readl(KS8695_GPIO_VA + KS8695_IOPC);
- if (gpio) /* GPIO: set bit to 0 */
- x &= ~enable[pin];
- else /* Internal function: set bit to 1 */
- x |= enable[pin];
- __raw_writel(x, KS8695_GPIO_VA + KS8695_IOPC);
-
- local_irq_restore(flags);
-}
-
-
-static unsigned short gpio_irq[] = { KS8695_IRQ_EXTERN0, KS8695_IRQ_EXTERN1, KS8695_IRQ_EXTERN2, KS8695_IRQ_EXTERN3 };
-
-/*
- * Configure GPIO pin as external interrupt source.
- */
-int ks8695_gpio_interrupt(unsigned int pin, unsigned int type)
-{
- unsigned long x, flags;
-
- if (pin > KS8695_GPIO_3) /* only GPIO 0..3 can generate IRQ */
- return -EINVAL;
-
- local_irq_save(flags);
-
- /* set pin as input */
- x = __raw_readl(KS8695_GPIO_VA + KS8695_IOPM);
- x &= ~IOPM(pin);
- __raw_writel(x, KS8695_GPIO_VA + KS8695_IOPM);
-
- local_irq_restore(flags);
-
- /* Set IRQ triggering type */
- irq_set_irq_type(gpio_irq[pin], type);
-
- /* enable interrupt mode */
- ks8695_gpio_mode(pin, 0);
-
- return 0;
-}
-EXPORT_SYMBOL(ks8695_gpio_interrupt);
-
-
-
-/* .... Generic GPIO interface .............................................. */
-
-/*
- * Configure the GPIO line as an input.
- */
-static int ks8695_gpio_direction_input(struct gpio_chip *gc, unsigned int pin)
-{
- unsigned long x, flags;
-
- if (pin > KS8695_GPIO_15)
- return -EINVAL;
-
- /* set pin to GPIO mode */
- ks8695_gpio_mode(pin, 1);
-
- local_irq_save(flags);
-
- /* set pin as input */
- x = __raw_readl(KS8695_GPIO_VA + KS8695_IOPM);
- x &= ~IOPM(pin);
- __raw_writel(x, KS8695_GPIO_VA + KS8695_IOPM);
-
- local_irq_restore(flags);
-
- return 0;
-}
-
-
-/*
- * Configure the GPIO line as an output, with default state.
- */
-static int ks8695_gpio_direction_output(struct gpio_chip *gc,
- unsigned int pin, int state)
-{
- unsigned long x, flags;
-
- if (pin > KS8695_GPIO_15)
- return -EINVAL;
-
- /* set pin to GPIO mode */
- ks8695_gpio_mode(pin, 1);
-
- local_irq_save(flags);
-
- /* set line state */
- x = __raw_readl(KS8695_GPIO_VA + KS8695_IOPD);
- if (state)
- x |= IOPD(pin);
- else
- x &= ~IOPD(pin);
- __raw_writel(x, KS8695_GPIO_VA + KS8695_IOPD);
-
- /* set pin as output */
- x = __raw_readl(KS8695_GPIO_VA + KS8695_IOPM);
- x |= IOPM(pin);
- __raw_writel(x, KS8695_GPIO_VA + KS8695_IOPM);
-
- local_irq_restore(flags);
-
- return 0;
-}
-
-
-/*
- * Set the state of an output GPIO line.
- */
-static void ks8695_gpio_set_value(struct gpio_chip *gc,
- unsigned int pin, int state)
-{
- unsigned long x, flags;
-
- if (pin > KS8695_GPIO_15)
- return;
-
- local_irq_save(flags);
-
- /* set output line state */
- x = __raw_readl(KS8695_GPIO_VA + KS8695_IOPD);
- if (state)
- x |= IOPD(pin);
- else
- x &= ~IOPD(pin);
- __raw_writel(x, KS8695_GPIO_VA + KS8695_IOPD);
-
- local_irq_restore(flags);
-}
-
-
-/*
- * Read the state of a GPIO line.
- */
-static int ks8695_gpio_get_value(struct gpio_chip *gc, unsigned int pin)
-{
- unsigned long x;
-
- if (pin > KS8695_GPIO_15)
- return -EINVAL;
-
- x = __raw_readl(KS8695_GPIO_VA + KS8695_IOPD);
- return (x & IOPD(pin)) != 0;
-}
-
-
-/*
- * Map GPIO line to IRQ number.
- */
-static int ks8695_gpio_to_irq(struct gpio_chip *gc, unsigned int pin)
-{
- if (pin > KS8695_GPIO_3) /* only GPIO 0..3 can generate IRQ */
- return -EINVAL;
-
- return gpio_irq[pin];
-}
-
-/* GPIOLIB interface */
-
-static struct gpio_chip ks8695_gpio_chip = {
- .label = "KS8695",
- .direction_input = ks8695_gpio_direction_input,
- .direction_output = ks8695_gpio_direction_output,
- .get = ks8695_gpio_get_value,
- .set = ks8695_gpio_set_value,
- .to_irq = ks8695_gpio_to_irq,
- .base = 0,
- .ngpio = 16,
- .can_sleep = false,
-};
-
-/* Register the GPIOs */
-void ks8695_register_gpios(void)
-{
- if (gpiochip_add_data(&ks8695_gpio_chip, NULL))
- printk(KERN_ERR "Unable to register core GPIOs\n");
-}
-
-/* .... Debug interface ..................................................... */
-
-#ifdef CONFIG_DEBUG_FS
-
-static int ks8695_gpio_show(struct seq_file *s, void *unused)
-{
- unsigned int enable[] = { IOPC_IOEINT0EN, IOPC_IOEINT1EN, IOPC_IOEINT2EN, IOPC_IOEINT3EN, IOPC_IOTIM0EN, IOPC_IOTIM1EN };
- unsigned int intmask[] = { IOPC_IOEINT0TM, IOPC_IOEINT1TM, IOPC_IOEINT2TM, IOPC_IOEINT3TM };
- unsigned long mode, ctrl, data;
- int i;
-
- mode = __raw_readl(KS8695_GPIO_VA + KS8695_IOPM);
- ctrl = __raw_readl(KS8695_GPIO_VA + KS8695_IOPC);
- data = __raw_readl(KS8695_GPIO_VA + KS8695_IOPD);
-
- seq_printf(s, "Pin\tI/O\tFunction\tState\n\n");
-
- for (i = KS8695_GPIO_0; i <= KS8695_GPIO_15 ; i++) {
- seq_printf(s, "%i:\t", i);
-
- seq_printf(s, "%s\t", (mode & IOPM(i)) ? "Output" : "Input");
-
- if (i <= KS8695_GPIO_3) {
- if (ctrl & enable[i]) {
- seq_printf(s, "EXT%i ", i);
-
- switch ((ctrl & intmask[i]) >> (4 * i)) {
- case IOPC_TM_LOW:
- seq_printf(s, "(Low)"); break;
- case IOPC_TM_HIGH:
- seq_printf(s, "(High)"); break;
- case IOPC_TM_RISING:
- seq_printf(s, "(Rising)"); break;
- case IOPC_TM_FALLING:
- seq_printf(s, "(Falling)"); break;
- case IOPC_TM_EDGE:
- seq_printf(s, "(Edges)"); break;
- }
- } else
- seq_printf(s, "GPIO\t");
- } else if (i <= KS8695_GPIO_5) {
- if (ctrl & enable[i])
- seq_printf(s, "TOUT%i\t", i - KS8695_GPIO_4);
- else
- seq_printf(s, "GPIO\t");
- } else {
- seq_printf(s, "GPIO\t");
- }
-
- seq_printf(s, "\t");
-
- seq_printf(s, "%i\n", (data & IOPD(i)) ? 1 : 0);
- }
- return 0;
-}
-
-DEFINE_SHOW_ATTRIBUTE(ks8695_gpio);
-
-static int __init ks8695_gpio_debugfs_init(void)
-{
- /* /sys/kernel/debug/ks8695_gpio */
- debugfs_create_file("ks8695_gpio", S_IFREG | S_IRUGO, NULL, NULL,
- &ks8695_gpio_fops);
- return 0;
-}
-postcore_initcall(ks8695_gpio_debugfs_init);
-
-#endif
--
2.20.0
next prev parent reply other threads:[~2019-08-09 20:28 UTC|newest]
Thread overview: 55+ messages / expand[flat|nested] mbox.gz Atom feed top
2019-08-09 20:27 [PATCH 00/16] ARM: remove ks8695 and w90x900 platforms Arnd Bergmann
2019-08-09 20:27 ` Arnd Bergmann
2019-08-09 20:27 ` Arnd Bergmann
2019-08-09 20:27 ` Arnd Bergmann
2019-08-09 20:27 ` [PATCH 01/16] ARM: remove ks8695 platform Arnd Bergmann
2019-08-09 20:27 ` Arnd Bergmann
2019-08-11 9:18 ` Ben Dooks
2019-08-12 3:59 ` Greg Ungerer
2019-08-13 15:27 ` Ben Dooks
2019-08-13 15:27 ` Ben Dooks
2019-08-09 20:27 ` [PATCH 02/16] serial: remove ks8695 driver Arnd Bergmann
2019-08-09 20:27 ` Arnd Bergmann [this message]
2019-08-10 9:03 ` [PATCH 03/16] gpio: " Linus Walleij
2019-08-09 20:27 ` [PATCH 04/16] watchdog: " Arnd Bergmann
2019-08-09 20:42 ` Guenter Roeck
2019-08-10 8:37 ` Arnd Bergmann
2019-08-10 12:56 ` Guenter Roeck
2019-08-09 20:27 ` [PATCH 05/16] net: " Arnd Bergmann
2019-08-09 20:27 ` [PATCH 06/16] watchdog: remove w90x900 driver Arnd Bergmann
2019-08-09 20:42 ` Guenter Roeck
2019-08-09 20:27 ` [PATCH 07/16] spi: " Arnd Bergmann
2019-08-12 10:36 ` Mark Brown
2019-08-12 13:06 ` Mark Brown
2019-08-09 20:27 ` [PATCH 08/16] ASoC: remove w90x900/nuc900 platform drivers Arnd Bergmann
2019-08-12 10:36 ` Mark Brown
2019-08-12 13:09 ` Applied "ASoC: remove w90x900/nuc900 platform drivers" to the asoc tree Mark Brown
2019-08-12 13:09 ` Mark Brown
2019-08-09 20:27 ` [PATCH 09/16] fbdev: remove w90x900/nuc900 platform drivers Arnd Bergmann
2019-08-09 20:27 ` Arnd Bergmann
2019-08-09 20:27 ` Arnd Bergmann
2019-08-13 13:30 ` Bartlomiej Zolnierkiewicz
2019-08-13 13:30 ` Bartlomiej Zolnierkiewicz
2019-08-13 13:40 ` Arnd Bergmann
2019-08-13 13:40 ` Arnd Bergmann
2019-08-13 13:40 ` Arnd Bergmann
2019-08-09 20:27 ` [PATCH 10/16] Input: remove w90x900 keyboard driver Arnd Bergmann
2019-08-09 21:56 ` Dmitry Torokhov
2019-08-09 20:27 ` [PATCH 11/16] Input: remove w90x900 touchscreen driver Arnd Bergmann
2019-08-09 21:56 ` Dmitry Torokhov
2019-08-09 20:27 ` [PATCH 12/16] mtd: rawnand: remove w90x900 driver Arnd Bergmann
2019-08-09 20:27 ` Arnd Bergmann
2019-08-10 8:21 ` Boris Brezillon
2019-08-10 8:21 ` Boris Brezillon
2019-08-26 12:58 ` Miquel Raynal
2019-08-26 12:58 ` Miquel Raynal
2019-08-09 20:27 ` [PATCH 13/16] net: remove w90p910-ether driver Arnd Bergmann
2019-08-09 20:27 ` [PATCH 14/16] rtc: remove w90x900/nuc900 driver Arnd Bergmann
2019-08-12 20:57 ` Alexandre Belloni
2019-08-09 20:27 ` [PATCH 15/16] usb: remove ehci-w90x900 driver Arnd Bergmann
2019-08-09 20:27 ` [PATCH 16/16] ARM: remove w90x900 platform Arnd Bergmann
2019-08-09 20:27 ` Arnd Bergmann
2019-08-10 7:29 ` [PATCH 00/16] ARM: remove ks8695 and w90x900 platforms Greg Kroah-Hartman
2019-08-10 7:29 ` Greg Kroah-Hartman
2019-08-10 7:29 ` Greg Kroah-Hartman
2019-08-10 7:29 ` Greg Kroah-Hartman
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20190809202749.742267-4-arnd@arndb.de \
--to=arnd@arndb.de \
--cc=bgolaszewski@baylibre.com \
--cc=linus.walleij@linaro.org \
--cc=linux-gpio@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=soc@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.