[PATCH 19/42] lpfc: Fix sg_seg_cnt for HBAs that don't support NVME

[James Smart <jsmart2021@gmail.com>]

On an SLi-3 adapter which does not support NVMe, but with the
driver global attribute to enable nvme on any adapter if it
does support NVMe (e.g. module parameter lpfc_enable_fc4_type=3),
the SGL and total SGE values are being munged by the protocol
enablement when it shouldn't be.

Correct by changing the location of where the NVME sgl information
is being applied, which will avoid any SLI-3-based adapter.

Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
---
 drivers/scsi/lpfc/lpfc_attr.c | 10 ----------
 drivers/scsi/lpfc/lpfc_init.c |  9 +++++++++
 2 files changed, 9 insertions(+), 10 deletions(-)

diff --git a/drivers/scsi/lpfc/lpfc_attr.c b/drivers/scsi/lpfc/lpfc_attr.c
index 90181afe0e28..7ac6508b7ed8 100644
--- a/drivers/scsi/lpfc/lpfc_attr.c
+++ b/drivers/scsi/lpfc/lpfc_attr.c
@@ -7196,16 +7196,6 @@ lpfc_get_cfgparam(struct lpfc_hba *phba)
 	lpfc_ras_fwlog_level_init(phba, lpfc_ras_fwlog_level);
 	lpfc_ras_fwlog_func_init(phba, lpfc_ras_fwlog_func);
 
-
-	/* If the NVME FC4 type is enabled, scale the sg_seg_cnt to
-	 * accommodate 512K and 1M IOs in a single nvme buf and supply
-	 * enough NVME LS iocb buffers for larger connectivity counts.
-	 */
-	if (phba->cfg_enable_fc4_type & LPFC_ENABLE_NVME) {
-		phba->cfg_sg_seg_cnt = LPFC_MAX_NVME_SEG_CNT;
-		phba->cfg_iocb_cnt = 5;
-	}
-
 	return;
 }
 
diff --git a/drivers/scsi/lpfc/lpfc_init.c b/drivers/scsi/lpfc/lpfc_init.c
index fcc1c45f2d35..84a77faed114 100644
--- a/drivers/scsi/lpfc/lpfc_init.c
+++ b/drivers/scsi/lpfc/lpfc_init.c
@@ -11702,6 +11702,15 @@ lpfc_get_sli4_parameters(struct lpfc_hba *phba, LPFC_MBOXQ_t *mboxq)
 		}
 	}
 
+	/* If the NVME FC4 type is enabled, scale the sg_seg_cnt to
+	 * accommodate 512K and 1M IOs in a single nvme buf and supply
+	 * enough NVME LS iocb buffers for larger connectivity counts.
+	 */
+	if (phba->cfg_enable_fc4_type & LPFC_ENABLE_NVME) {
+		phba->cfg_sg_seg_cnt = LPFC_MAX_NVME_SEG_CNT;
+		phba->cfg_iocb_cnt = 5;
+	}
+
 	/* Only embed PBDE for if_type 6, PBDE support requires xib be set */
 	if ((bf_get(lpfc_sli_intf_if_type, &phba->sli4_hba.sli_intf) !=
 	    LPFC_SLI_INTF_IF_TYPE_6) || (!bf_get(cfg_xib, mbx_sli4_parameters)))
-- 
2.13.7