All of lore.kernel.org
 help / color / mirror / Atom feed
From: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
To: jorge.ramirez-ortiz@linaro.org, agross@kernel.org,
	linux@roeck-us.net, wim@linux-watchdog.org,
	bjorn.andersson@linaro.org
Cc: linux-arm-msm@vger.kernel.org, linux-watchdog@vger.kernel.org,
	linux-kernel@vger.kernel.org
Subject: [PATCH v4] watchdog: qcom: support pre-timeout when the bark irq is available
Date: Thu,  5 Sep 2019 23:00:35 +0200	[thread overview]
Message-ID: <20190905210035.9985-1-jorge.ramirez-ortiz@linaro.org> (raw)

Use the bark interrupt as the pre-timeout notifier whenever this
interrupt is available.

By default, the pretimeout notification shall occur one second earlier
than the timeout.

Signed-off-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
---
 v4:
     address Guenter Roeck comments as follows:
       remove unnecessary include and private variable
       provide macro for WDT EN register values
       use pretimeout as per its API intent
       handle EPROBE_DEFER on get_irq
     also:
       handle the irq registration as done in pm8916_wdt.c
 v3:
    remove unnecesary variable added to private.

 v2:
    register the pre-timeout notifier instead.

 v1:
 drivers/watchdog/qcom-wdt.c | 64 ++++++++++++++++++++++++++++++++++---
 1 file changed, 59 insertions(+), 5 deletions(-)

diff --git a/drivers/watchdog/qcom-wdt.c b/drivers/watchdog/qcom-wdt.c
index 7be7f87be28f..0f1d29eeb81d 100644
--- a/drivers/watchdog/qcom-wdt.c
+++ b/drivers/watchdog/qcom-wdt.c
@@ -10,6 +10,7 @@
 #include <linux/platform_device.h>
 #include <linux/watchdog.h>
 #include <linux/of_device.h>
+#include <linux/interrupt.h>
 
 enum wdt_reg {
 	WDT_RST,
@@ -19,6 +20,9 @@ enum wdt_reg {
 	WDT_BITE_TIME,
 };
 
+#define QCOM_WDT_ENABLE		BIT(0)
+#define QCOM_WDT_ENABLE_IRQ	BIT(1)
+
 static const u32 reg_offset_data_apcs_tmr[] = {
 	[WDT_RST] = 0x38,
 	[WDT_EN] = 0x40,
@@ -54,15 +58,38 @@ struct qcom_wdt *to_qcom_wdt(struct watchdog_device *wdd)
 	return container_of(wdd, struct qcom_wdt, wdd);
 }
 
+static inline int qcom_get_enable(struct watchdog_device *wdd)
+{
+	int enable = QCOM_WDT_ENABLE;
+
+	if (wdd->info->options & WDIOF_PRETIMEOUT)
+		enable |= QCOM_WDT_ENABLE_IRQ;
+
+	return enable;
+}
+
+static irqreturn_t qcom_wdt_isr(int irq, void *arg)
+{
+	struct watchdog_device *wdd = arg;
+
+	watchdog_notify_pretimeout(wdd);
+
+	return IRQ_HANDLED;
+}
+
 static int qcom_wdt_start(struct watchdog_device *wdd)
 {
 	struct qcom_wdt *wdt = to_qcom_wdt(wdd);
+	unsigned int bark = wdd->timeout;
+
+	if (wdd->pretimeout)
+		bark = bark - wdd->pretimeout;
 
 	writel(0, wdt_addr(wdt, WDT_EN));
 	writel(1, wdt_addr(wdt, WDT_RST));
-	writel(wdd->timeout * wdt->rate, wdt_addr(wdt, WDT_BARK_TIME));
+	writel(bark * wdt->rate, wdt_addr(wdt, WDT_BARK_TIME));
 	writel(wdd->timeout * wdt->rate, wdt_addr(wdt, WDT_BITE_TIME));
-	writel(1, wdt_addr(wdt, WDT_EN));
+	writel(qcom_get_enable(wdd), wdt_addr(wdt, WDT_EN));
 	return 0;
 }
 
@@ -89,6 +116,13 @@ static int qcom_wdt_set_timeout(struct watchdog_device *wdd,
 	return qcom_wdt_start(wdd);
 }
 
+static int qcom_wdt_set_pretimeout(struct watchdog_device *wdd,
+				   unsigned int timeout)
+{
+	wdd->pretimeout = timeout;
+	return qcom_wdt_start(wdd);
+}
+
 static int qcom_wdt_restart(struct watchdog_device *wdd, unsigned long action,
 			    void *data)
 {
@@ -105,7 +139,7 @@ static int qcom_wdt_restart(struct watchdog_device *wdd, unsigned long action,
 	writel(1, wdt_addr(wdt, WDT_RST));
 	writel(timeout, wdt_addr(wdt, WDT_BARK_TIME));
 	writel(timeout, wdt_addr(wdt, WDT_BITE_TIME));
-	writel(1, wdt_addr(wdt, WDT_EN));
+	writel(qcom_get_enable(wdd), wdt_addr(wdt, WDT_EN));
 
 	/*
 	 * Actually make sure the above sequence hits hardware before sleeping.
@@ -121,6 +155,7 @@ static const struct watchdog_ops qcom_wdt_ops = {
 	.stop		= qcom_wdt_stop,
 	.ping		= qcom_wdt_ping,
 	.set_timeout	= qcom_wdt_set_timeout,
+	.set_pretimeout	= qcom_wdt_set_pretimeout,
 	.restart        = qcom_wdt_restart,
 	.owner		= THIS_MODULE,
 };
@@ -133,6 +168,15 @@ static const struct watchdog_info qcom_wdt_info = {
 	.identity	= KBUILD_MODNAME,
 };
 
+static const struct watchdog_info qcom_wdt_pt_info = {
+	.options	= WDIOF_KEEPALIVEPING
+			| WDIOF_MAGICCLOSE
+			| WDIOF_SETTIMEOUT
+			| WDIOF_PRETIMEOUT
+			| WDIOF_CARDRESET,
+	.identity	= KBUILD_MODNAME,
+};
+
 static void qcom_clk_disable_unprepare(void *data)
 {
 	clk_disable_unprepare(data);
@@ -146,7 +190,7 @@ static int qcom_wdt_probe(struct platform_device *pdev)
 	struct device_node *np = dev->of_node;
 	const u32 *regs;
 	u32 percpu_offset;
-	int ret;
+	int irq, ret;
 
 	regs = of_device_get_match_data(dev);
 	if (!regs) {
@@ -204,7 +248,17 @@ static int qcom_wdt_probe(struct platform_device *pdev)
 		return -EINVAL;
 	}
 
-	wdt->wdd.info = &qcom_wdt_info;
+	irq = platform_get_irq(pdev, 0);
+	if (irq > 0) {
+		if (devm_request_irq(dev, irq, qcom_wdt_isr,
+				     IRQF_TRIGGER_RISING, "wdt_bark",
+				     &wdt->wdd))
+			irq = 0;
+	} else if (irq == -EPROBE_DEFER)
+		return -EPROBE_DEFER;
+
+	wdt->wdd.info = irq > 0 ? &qcom_wdt_pt_info : &qcom_wdt_info;
+	wdt->wdd.pretimeout = irq > 0 ? 1 : 0;
 	wdt->wdd.ops = &qcom_wdt_ops;
 	wdt->wdd.min_timeout = 1;
 	wdt->wdd.max_timeout = 0x10000000U / wdt->rate;
-- 
2.23.0


             reply	other threads:[~2019-09-05 21:00 UTC|newest]

Thread overview: 8+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2019-09-05 21:00 Jorge Ramirez-Ortiz [this message]
2019-09-05 21:19 ` [PATCH v4] watchdog: qcom: support pre-timeout when the bark irq is available Guenter Roeck
2019-09-05 21:34   ` Jorge Ramirez
2019-09-06 12:59     ` Guenter Roeck
2019-09-06 13:25       ` Jorge Ramirez
2019-09-06 17:40 ` Bjorn Andersson
2019-09-06 19:08   ` Guenter Roeck
2019-09-06 19:15   ` Jorge Ramirez

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20190905210035.9985-1-jorge.ramirez-ortiz@linaro.org \
    --to=jorge.ramirez-ortiz@linaro.org \
    --cc=agross@kernel.org \
    --cc=bjorn.andersson@linaro.org \
    --cc=linux-arm-msm@vger.kernel.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=linux-watchdog@vger.kernel.org \
    --cc=linux@roeck-us.net \
    --cc=wim@linux-watchdog.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.