All of lore.kernel.org
 help / color / mirror / Atom feed
From: Bjorn Andersson <bjorn.andersson@linaro.org>
To: Andy Gross <agross@kernel.org>, Rob Herring <robh+dt@kernel.org>,
	Mark Rutland <mark.rutland@arm.com>
Cc: linux-arm-msm@vger.kernel.org, devicetree@vger.kernel.org,
	linux-kernel@vger.kernel.org
Subject: [PATCH 03/11] arm64: dts: qcom: msm8996: Move regulator consumers to db820c
Date: Sun, 20 Oct 2019 22:13:14 -0700	[thread overview]
Message-ID: <20191021051322.297560-4-bjorn.andersson@linaro.org> (raw)
In-Reply-To: <20191021051322.297560-1-bjorn.andersson@linaro.org>

Supplies for the various components in the SoC depends on board layout,
so move the supply definitions to db820c.dtsi instead of carrying them
in the platform dtsi.

Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
---
 arch/arm64/boot/dts/qcom/apq8096-db820c.dtsi | 44 ++++++++++++++++++++
 arch/arm64/boot/dts/qcom/msm8996.dtsi        | 44 --------------------
 2 files changed, 44 insertions(+), 44 deletions(-)

diff --git a/arch/arm64/boot/dts/qcom/apq8096-db820c.dtsi b/arch/arm64/boot/dts/qcom/apq8096-db820c.dtsi
index 44ec3eb1c8e8..21e029afb27b 100644
--- a/arch/arm64/boot/dts/qcom/apq8096-db820c.dtsi
+++ b/arch/arm64/boot/dts/qcom/apq8096-db820c.dtsi
@@ -142,6 +142,10 @@
 	status = "okay";
 };
 
+&camss {
+	vdda-supply = <&pm8994_l2>;
+};
+
 &sdhc2 {
 	/* External SD card */
 	pinctrl-names = "default", "sleep";
@@ -155,10 +159,28 @@
 
 &ufsphy {
 	status = "okay";
+
+	vdda-phy-supply = <&pm8994_l28>;
+	vdda-pll-supply = <&pm8994_l12>;
+
+	vdda-phy-max-microamp = <18380>;
+	vdda-pll-max-microamp = <9440>;
+
+	vddp-ref-clk-supply = <&pm8994_l25>;
+	vddp-ref-clk-max-microamp = <100>;
+	vddp-ref-clk-always-on;
 };
 
 &ufshc {
 	status = "okay";
+
+	vcc-supply = <&pm8994_l20>;
+	vccq-supply = <&pm8994_l25>;
+	vccq2-supply = <&pm8994_s4>;
+
+	vcc-max-microamp = <600000>;
+	vccq-max-microamp = <450000>;
+	vccq2-max-microamp = <450000>;
 };
 
 &msmgpio {
@@ -369,18 +391,31 @@
 
 &pcie_phy {
 	status = "okay";
+
+	vdda-phy-supply = <&pm8994_l28>;
+	vdda-pll-supply = <&pm8994_l12>;
 };
 
 &usb3phy {
 	status = "okay";
+
+	vdda-phy-supply = <&pm8994_l28>;
+	vdda-pll-supply = <&pm8994_l12>;
+
 };
 
 &hsusb_phy1 {
 	status = "okay";
+
+	vdda-pll-supply = <&pm8994_l12>;
+	vdda-phy-dpdm-supply = <&pm8994_l24>;
 };
 
 &hsusb_phy2 {
 	status = "okay";
+
+	vdda-pll-supply = <&pm8994_l12>;
+	vdda-phy-dpdm-supply = <&pm8994_l24>;
 };
 
 &usb3 {
@@ -408,22 +443,31 @@
 	status = "okay";
 	perst-gpio = <&msmgpio 35 GPIO_ACTIVE_LOW>;
 	vddpe-3v3-supply = <&wlan_en>;
+	vdda-supply = <&pm8994_l28>;
 };
 
 &pcie1 {
 	status = "okay";
 	perst-gpio = <&msmgpio 130 GPIO_ACTIVE_LOW>;
+	vdda-supply = <&pm8994_l28>;
 };
 
 &pcie2 {
 	status = "okay";
 	perst-gpio = <&msmgpio 114 GPIO_ACTIVE_LOW>;
+	vdda-supply = <&pm8994_l28>;
 };
 
 &wcd9335 {
 	clock-names = "mclk", "slimbus";
 	clocks = <&div1_mclk>,
 		 <&rpmcc RPM_SMD_BB_CLK1>;
+
+	vdd-buck-supply = <&pm8994_s4>;
+	vdd-buck-sido-supply = <&pm8994_s4>;
+	vdd-tx-supply = <&pm8994_s4>;
+	vdd-rx-supply = <&pm8994_s4>;
+	vdd-io-supply = <&pm8994_s4>;
 };
 
 &mdss {
diff --git a/arch/arm64/boot/dts/qcom/msm8996.dtsi b/arch/arm64/boot/dts/qcom/msm8996.dtsi
index 36f161547aa6..a297d3223161 100644
--- a/arch/arm64/boot/dts/qcom/msm8996.dtsi
+++ b/arch/arm64/boot/dts/qcom/msm8996.dtsi
@@ -1322,16 +1322,6 @@
 			reg-names = "phy_mem";
 			#phy-cells = <0>;
 
-			vdda-phy-supply = <&pm8994_l28>;
-			vdda-pll-supply = <&pm8994_l12>;
-
-			vdda-phy-max-microamp = <18380>;
-			vdda-pll-max-microamp = <9440>;
-
-			vddp-ref-clk-supply = <&pm8994_l25>;
-			vddp-ref-clk-max-microamp = <100>;
-			vddp-ref-clk-always-on;
-
 			clock-names = "ref_clk_src", "ref_clk";
 			clocks = <&rpmcc RPM_SMD_LN_BB_CLK>,
 				 <&gcc GCC_UFS_CLKREF_CLK>;
@@ -1347,14 +1337,6 @@
 			phys = <&ufsphy>;
 			phy-names = "ufsphy";
 
-			vcc-supply = <&pm8994_l20>;
-			vccq-supply = <&pm8994_l25>;
-			vccq2-supply = <&pm8994_s4>;
-
-			vcc-max-microamp = <600000>;
-			vccq-max-microamp = <450000>;
-			vccq2-max-microamp = <450000>;
-
 			power-domains = <&gcc UFS_GDSC>;
 
 			clock-names =
@@ -1456,9 +1438,6 @@
 				<&gcc GCC_PCIE_CLKREF_CLK>;
 			clock-names = "aux", "cfg_ahb", "ref";
 
-			vdda-phy-supply = <&pm8994_l28>;
-			vdda-pll-supply = <&pm8994_l12>;
-
 			resets = <&gcc GCC_PCIE_PHY_BCR>,
 				<&gcc GCC_PCIE_PHY_COM_BCR>,
 				<&gcc GCC_PCIE_PHY_COM_NOCSR_BCR>;
@@ -1518,9 +1497,6 @@
 				<&gcc GCC_USB3_CLKREF_CLK>;
 			clock-names = "aux", "cfg_ahb", "ref";
 
-			vdda-phy-supply = <&pm8994_l28>;
-			vdda-pll-supply = <&pm8994_l12>;
-
 			resets = <&gcc GCC_USB3_PHY_BCR>,
 				<&gcc GCC_USB3PHY_PHY_BCR>;
 			reset-names = "phy", "common";
@@ -1547,9 +1523,6 @@
 				<&gcc GCC_RX1_USB2_CLKREF_CLK>;
 			clock-names = "cfg_ahb", "ref";
 
-			vdda-pll-supply = <&pm8994_l12>;
-			vdda-phy-dpdm-supply = <&pm8994_l24>;
-
 			resets = <&gcc GCC_QUSB2PHY_PRIM_BCR>;
 			nvmem-cells = <&qusb2p_hstx_trim>;
 			status = "disabled";
@@ -1564,9 +1537,6 @@
 				<&gcc GCC_RX2_USB2_CLKREF_CLK>;
 			clock-names = "cfg_ahb", "ref";
 
-			vdda-pll-supply = <&pm8994_l12>;
-			vdda-phy-dpdm-supply = <&pm8994_l24>;
-
 			resets = <&gcc GCC_QUSB2PHY_SEC_BCR>;
 			nvmem-cells = <&qusb2s_hstx_trim>;
 			status = "disabled";
@@ -1770,7 +1740,6 @@
 				"vfe1_stream",
 				"vfe_ahb",
 				"vfe_axi";
-			vdda-supply = <&pm8994_l2>;
 			iommus = <&vfe_smmu 0>,
 				 <&vfe_smmu 1>,
 				 <&vfe_smmu 2>,
@@ -1882,9 +1851,6 @@
 				pinctrl-0 = <&pcie0_clkreq_default &pcie0_perst_default &pcie0_wake_default>;
 				pinctrl-1 = <&pcie0_clkreq_sleep &pcie0_perst_default &pcie0_wake_sleep>;
 
-
-				vdda-supply = <&pm8994_l28>;
-
 				linux,pci-domain = <0>;
 
 				clocks = <&gcc GCC_PCIE_0_PIPE_CLK>,
@@ -1937,8 +1903,6 @@
 				pinctrl-0 = <&pcie1_clkreq_default &pcie1_perst_default &pcie1_wake_default>;
 				pinctrl-1 = <&pcie1_clkreq_sleep &pcie1_perst_default &pcie1_wake_sleep>;
 
-
-				vdda-supply = <&pm8994_l28>;
 				linux,pci-domain = <1>;
 
 				clocks = <&gcc GCC_PCIE_1_PIPE_CLK>,
@@ -1990,8 +1954,6 @@
 				pinctrl-0 = <&pcie2_clkreq_default &pcie2_perst_default &pcie2_wake_default>;
 				pinctrl-1 = <&pcie2_clkreq_sleep &pcie2_perst_default &pcie2_wake_sleep >;
 
-				vdda-supply = <&pm8994_l28>;
-
 				linux,pci-domain = <2>;
 				clocks = <&gcc GCC_PCIE_2_PIPE_CLK>,
 					<&gcc GCC_PCIE_2_AUX_CLK>,
@@ -2056,12 +2018,6 @@
 
 					slim-ifc-dev  = <&tasha_ifd>;
 
-					vdd-buck-supply = <&pm8994_s4>;
-					vdd-buck-sido-supply = <&pm8994_s4>;
-					vdd-tx-supply = <&pm8994_s4>;
-					vdd-rx-supply = <&pm8994_s4>;
-					vdd-io-supply = <&pm8994_s4>;
-
 					#sound-dai-cells = <1>;
 				};
 			};
-- 
2.23.0


  parent reply	other threads:[~2019-10-21  5:14 UTC|newest]

Thread overview: 15+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2019-10-21  5:13 [PATCH 00/11] arm64: dts: qcom: msm8996: Introduce IFC6640 Bjorn Andersson
2019-10-21  5:13 ` [PATCH 01/11] arm64: dts: qcom: db820c: Move non-soc entries out of /soc Bjorn Andersson
2019-10-21  5:13 ` [PATCH 02/11] arm64: dts: qcom: msm8996: Use node references in db820c Bjorn Andersson
2019-10-21  5:13 ` Bjorn Andersson [this message]
2019-10-21  5:13 ` [PATCH 04/11] arm64: dts: qcom: msm8996: Move regulators to db820c Bjorn Andersson
2019-10-21  5:13 ` [PATCH 05/11] arm64: dts: qcom: db820c: Group root nodes Bjorn Andersson
2019-10-21  5:13 ` [PATCH 06/11] arm64: dts: qcom: db820c: Sort all nodes Bjorn Andersson
2019-10-21  5:13 ` [PATCH 07/11] arm64: dts: qcom: db820c: Remove pin specific files Bjorn Andersson
2019-10-21  5:13 ` [PATCH 08/11] arm64: dts: qcom: msm8996: Pad addresses Bjorn Andersson
2019-10-21  5:13 ` [PATCH 09/11] arm64: dts: qcom: msm8996: Sort all nodes in msm8996.dtsi Bjorn Andersson
2019-10-21  5:13 ` [PATCH 10/11] arm64: dts: qcom: db820c: Use regulator names from schematics Bjorn Andersson
2019-10-21  5:13 ` [PATCH 11/11] arm64: dts: qcom: msm8996: Introduce IFC6640 Bjorn Andersson
2019-11-03  8:13 ` [PATCH 00/11] " Vinod Koul
2019-11-04  4:55   ` Bjorn Andersson
2019-11-04  9:27     ` Vinod Koul

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20191021051322.297560-4-bjorn.andersson@linaro.org \
    --to=bjorn.andersson@linaro.org \
    --cc=agross@kernel.org \
    --cc=devicetree@vger.kernel.org \
    --cc=linux-arm-msm@vger.kernel.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=mark.rutland@arm.com \
    --cc=robh+dt@kernel.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body. 
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.